User manual INFINITI Q45 - 1997

FOREWORD Your INFINITI represents a new way of thinking about car design. It integrates advanced engineering and superior craftsmanship with a simple, refined aesthetic sensitivity associated with traditional Japanese culture. The result is a different notion of luxury and beauty. The car itself is important, but so also is the sense of harmony that the car evokes in its driver, and the sense of satisfaction you feel with the INFINITI --from the way it looks and drives to the high level of dealer service. To ensure that you enjoy your INFINITI to the fullest, we encourage you to read this Owner's Manual immediately. It explains all of the features, controls and performance characteristics of your INFINITI; it also provides important instructions and safety information. A separate Warranty Information Booklet is to be found in your Owner's literature portfolio. Always carry it with you when you take your INFINITI to an authorized dealer. The portfolio contents provide complete information about all warranties covering this vehicle, the periodic maintenance required to keep the warranties in effect as well as the INFINITI Roadside Assistance program. INFINITI is dedicated to providing a satisfying ownership experience for as long as you own your car. Should you have any questions regarding your INFINITI or your INFINITI dealer, please contact our Consumer Affairs department at 1-800-662-6200. In Hawaii 808-836-0848 (Oahu number). In Canada 1-800-363-4520. Thank you. WHEN READING THE MANUAL This manual includes information for all options available on this model. Therefore, you may find some information that does not apply to your vehicle. All information, specifications and illustrations in this manual are those in effect at the time of printing. INFINITI reserves the right to change specifications or design at any time without notice. tions. In addition, damage or performance problems resulting from modification may not be covered under INFINITI warranties. READ FIRST -- THEN DRIVE SAFELY Before driving your vehicle please read your Owner's Manual carefully. This will ensure familiarity with controls and maintenance requirements, assisting you in the safe operation of your vehicle. WARNING IMPORTANT SAFETY INFORMATION REMINDERS FOR SAFETY! Follow these five important driving rules to help ensure a safe and comfortable trip for you and your passengers! MODIFICATION OF YOUR VEHICLE This vehicle should not be modified. Modification could affect its performance, safety or durability, and may even violate governmental regula- NEVER drive under the influence of alcohol or drugs. ALWAYS observe posted speed limits and never drive too fast for conditions. ALWAYS use your seat belts and appropriate child restraint systems. ALWAYS provide information about the proper use of vehicle safety features to all occupants of the vehicle. ALWAYS review this Owner's Manual for important safety information. IMPORTANT INFORMATION ABOUT THIS MANUAL You will see the various symbols in this manual. They are used in the following ways: WARNING This is used to indicate the presence of a hazard that could cause death or serious personal injury. To avoid or reduce the risk, the procedures must be followed precisely. SII0151 If you see this symbol, it means ``Do not do this'' or ``Do not let this happen''. CAUTION This is used to indicate the presence of a hazard that could cause minor or moderate personal injury or danger to your vehicle. To avoid or reduce the risk, the procedures must be followed carefully. © 1996 NISSAN MOTOR CO., LTD. TOKYO, JAPAN All rights reserved. No part of this Owner's Manual may be reproduced or stored in a retrieval system, or transmitted in any form, or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of Nissan Motor Co., Ltd. TABLE OF CONTENTS INSTRUMENTS AND CONTROLS .......................................................... 1-1 PRE-DRIVING CHECKS AND ADJUSTMENTS............................................ 2-1 HEATER/AIR CONDITIONER/AUDIO ....................................................... 3-1 STARTING AND DRIVING................................................................... 4-1 IN CASE OF EMERGENCY .................................................................. 5-1 APPEARANCE AND CARE................................................................... 6-1 DO-IT-YOURSELF ............................................................................ 7-1 MAINTENANCE ............................................................................... 8-1 TECHNICAL AND CONSUMER INFORMATION........................................... 9-1 INDEX ........................................................................................ 10-1 1 INSTRUMENTS AND CONTROLS Meters and gauges .................................... 1-3 Warning/indicator light and chime ............. 1-7 Security systems ...................................... 1-12 Windshield wiper and washer switch ...... 1-14 Rear window and outside door mirror defogger switch ....................................... 1-15 Headlight and turn signal switch ............. 1-16 Front fog light switch ............................... 1-18 Instrument brightness control ................. 1-18 Hazard warning flasher switch ................. 1-19 Heated seats (If so equipped) .................. 1-19 Traction control (TCS) cancel switch ...... 1-20 Cigarette lighters and ashtrays ................ Cup holder ............................................... Console box ............................................. Power window ......................................... Sunroof (If so equipped) ......................... Clock ........................................................ Interior light ............................................. Personal light ........................................... Vanity mirror light .................................... Integrated HomeLink Transmitter .......... 1-21 1-22 1-23 1-24 1-25 1-26 1-26 1-27 1-28 1-28 INSTRUMENTS AND CONTROLS See the page indicated in parentheses for operating details. SII0157 1-2 INSTRUMENTS AND CONTROLS METERS AND GAUGES 80 60 40 E 80 120 100 160 120 200 F 40 20 0 140 240 0 MPH km/h 160 P R N D 2 1 3 2 1 0 4 5 6 7 C PREMIUM UNLEADED FUEL ONLY H x1000r/min 8 SII0072 1-3 INSTRUMENTS AND CONTROLS SPEEDOMETER TRIP ODOMETER The trip odometer records the distance of individual trips. Before each trip, set the trip odometer to zero by pushing the RESET button. CAUTION When engine speed approaches the red zone, shift to a higher gear. Operating the engine in the red zone may cause serious engine damage. TACHOMETER The tachometer indicates engine speed in revolutions per minute (r/min). SII0073 The speedometer indicates vehicle speed. ODOMETER The odometer records the total mileage the vehicle has been driven. SII0074 1-4 INSTRUMENTS AND CONTROLS ENGINE COOLANT TEMPERATURE GAUGE The gauge indicates engine coolant temperature. CAUTION If the gauge indicates over the normal range, stop the vehicle as soon as safely possible. If the engine is overheated, continued operation of the vehicle may seriously damage the engine. See ``In case of emergency'' section for immediate action required. SII0076 SII0075 FUEL GAUGE The gauge indicates the APPROXIMATE fuel level in the tank. The gauge may move slightly during braking, turning, acceleration, or going up or down hill. The gauge needle is designed to remain in approximately the same position, even when the ignition key is turned ``OFF''. Refill the fuel tank before the gauge registers Empty. The indicator light comes on when the fuel tank is getting low. Refuel as soon as it is convenient, preferably before the gauge Engine coolant temperature will vary with the outside air temperature and driving conditions. 1-5 INSTRUMENTS AND CONTROLS reaches ``E''. There should be a small reserve of fuel in the tank when the fuel gauge needle reaches ``E''. 1-6 INSTRUMENTS AND CONTROLS WARNING/INDICATOR LIGHT AND CHIME or Brake warning light Supplemental air bag warning light Low washer fluid warning light or Anti-lock brake system warning light CRUISE indicator light Traction control system indicator light Turn signal/hazard indicator lights High beam indicator light (Blue) Slip indicator light Charge warning light Door open warning light Seat belt warning light Stop/tail warning light or Malfunction indicator light. Overdrive off indicator light Engine oil pressure warning light Checking bulbs Apply the parking brake and turn the ignition key to ``ON'' without starting the engine. The following lights will come on: , or , , or , or , , The following lights come on briefly and then go off: , If any light fails to come on, it may indicate a burned-out bulb or an open circuit in the electrical system. Have the system repaired 1-7 promptly. INSTRUMENTS AND CONTROLS Engine oil pressure warning light This light warns of low engine oil pressure. If the light flickers or comes on during normal driving, pull off the road in a safe area, stop the engine immediately and call an INFINITI dealer or other authorized repair shop. The oil pressure warning light is not designed to indicate a low oil level. Use the dipstick to check the oil level. See ``Engine oil'' in the ``Do-it-yourself'' section. Charge warning light If the light comes on while the engine is running, it may indicate that there is something wrong with the charging system. Turn the engine off and check the alternator belt. If the belt is loose, broken, missing or if the light remains on, see your INFINITI dealer immediately. Supplemental air bag warning light When the ignition key is in the ``ON'' or ``START'' position, the supplemental air bag light will illuminate for about 7 seconds and then turn off. This means the system is operational. If any of the following conditions occur, the supplemental air bag needs servicing and your INFINITI must be taken to your nearest authorized INFINITI dealer. 1. The supplemental air bag light goes off within 7 seconds. 2. The supplemental air bag light flashes intermittently or remains on (after 7 seconds). 3. The supplemental air bag light does not come on at all. Unless checked and repaired, the Supplemen- CAUTION Do not continue driving if the belt is loose, broken or missing. See section 5, In case of emergency. CAUTION Running the engine with the oil pressure warning light on could cause serious damage to the engine almost immediately. Turn off the engine as soon as it is safe to do so. See Section 5, In case of emergency. Door open warning light This light comes on when any of the doors are not closed securely while the ignition key is ``ON''. 1-8 INSTRUMENTS AND CONTROLS tal Restraint System may not function properly. For additional details on the Supplemental Air Bag System, see section 2. then go off.) At the same time, the chime will sound for about six seconds unless the driver's seat belt is securely fastened. Refer to ``Seat belts'' in the ``Pre-driving checks and adjustments'' section for precautions on seat belt usage. If the seat belt warning light blinks, there may be something wrong with the pre-tensioner seat belt. In this case, the pre-tensioner will not operate properly. Have it checked by your INFINITI dealer. For additional details on the pre-tensioner seat belt system, see section 2. or Brake warning light This light functions for both the parking brake and the foot brake systems. Parking brake indicator: The light comes on when the parking brake is applied. Low brake fluid warning: The light warns of a low brake fluid level. If the light comes on while the engine is running with the parking brake not applied, stop the vehicle and perform the following: 1. Check the brake fluid level. Add brake fluid as necessary. See ``Brake fluid'' in the ``Do-it-yourself'' section. 2. If the brake fluid level is correct: Have the warning system checked by an INFINITI dealer. WARNING If the supplemental air bag warning light is on, it could mean that the supplemental air bag system will not operate in an accident. Seat belt warning light and chime The light and chime remind you to fasten seat belts. The light illuminates whenever the ignition key is turned to ``ON'', and will remain illuminated until the driver's seat belt is fastened. (When the ignition key is turned to ``ON'' with the driver's seat belt fastened, the light will illuminate for about 7 seconds and Low washer fluid warning light This light comes on when the washer tank fluid is at a low level. Add washer fluid as necessary. See the ``Do-it-yourself'' section. 1-9 INSTRUMENTS AND CONTROLS or WARNING Your brake system may not be working properly if the warning light is on. Driving could be dangerous. If you judge it to be safe, drive carefully to the nearest service station for repairs. Otherwise, have your vehicle towed. Pressing the brake pedal with the engine stopped could increase your stopping distance and braking will require greater pedal effort as well as pedal travel. If the level is below the MINIMUM mark on the brake fluid reservoir, do not drive until the brake system has been checked at an INFINITI dealer. Anti-lock brake warning light operating i.e. that the traction control system is temporarily out of order. Have the system checked by your INFINITI dealer. If an abnormality occurs in the system, the traction control function will be canceled but the vehicle can still be driven. See ``Traction control system'' in the ``Starting and driving'' section. If the light comes on while the engine is running, it may indicate there is something wrong with the anti-lock portion of the brake system. In either case, have the system checked by your INFINITI dealer. If an abnormality occurs in the system, the anti-lock function will cease but the ordinary brakes will continue to operate normally. If the light comes on while you are driving, contact your INFINITI dealer for repair. Slip indicator light This indicator will blink when the traction control system is operating, thus alerting the driver to the fact that the road surface is slippery and the vehicle is nearing its traction limits. Traction control system indicator light When the traction control system switch is off, this light comes on. When the TCS indicator light and slip indicator light come on with the traction control system switch turned on, this light alerts the driver to the fact that the traction control system's fail-safe mode is 1-10 Overdrive off indicator light This light comes on when the overdrive switch is pushed to the ``OFF '' position. However when the ignition key is in the ``ON'' or ``START'' position and the overdrive switch INSTRUMENTS AND CONTROLS is not in the ``OFF '' position, the light will illuminate for about 2 seconds and then turn off. This means the system is operational. CRUISE indicator light The light comes on while the vehicle speed is controlled by the cruise control system. Turn signal/hazard indicator lights The light flashes when the turn signal switch lever or hazard switch is turned on. when the vehicle is in motion whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the warning sound is heard. Key reminder chime The chime will sound if the driver side door is opened while the key is left in the ignition switch (ignition switch is turned off). Remove the key and take it with you when leaving the vehicle. or Malfunction indicator light (MIL) Stop/tail warning light If the light comes on with the engine running and with the light switch on, or when the brake pedal is depressed, one or more stop/tail light bulbs are burned out. Replace the stop/tail light bulb. If the Malfunction indicator light comes on steady or blinks while the engine is running, it may indicate a potential emission control problem. The Malfunction indicator light will come on in one of two ways: Malfunction indicator light on steady -- An emission control system malfunction has been detected. Have the vehicle inspected by an authorized INFINITI dealer. You do not need to have your vehicle towed to the dealer. Malfunction indicator light blinking -- An engine misfire has been detected which may damage the emission control system. Light reminder chime A chime will sound when the driver side door is opened if the light switch is turned on (ignition switch is turned off). Turn the light switch off when you leave the vehicle. High beam indicator light (Blue) This light comes on when the headlight high beam is on and goes out when the low beam is selected. Brake pad wear warning The disc brake pads have audible wear warnings. When a brake pad requires replacement, it will make a high pitched scraping sound 1-11 INSTRUMENTS AND CONTROLS To reduce or avoid emission control system damage: * do not drive at speeds above 45 MPH (72 km/h). * avoid hard acceleration or deceleration. * avoid steep uphill grades. * if possible, reduce the amount of cargo being hauled or towed. The malfunction indicator light may stop blinking and come on steady. Have the vehicle inspected by an authorized INFINITI dealer. You do not need to have your vehicle towed to the dealer. SECURITY SYSTEMS could lead to poor driveability, reduced fuel economy, and possible damage to the emission control system, which may affect your warranty coverage. Some conditions may cause the malfunction indicator light to come on steady or blink. For example, running the vehicle out of fuel, which causes the engine to misfire, may cause the malfunction indicator light to come on steady or blink. If you suspect that you experienced such a condition, drive the vehicle to an authorized INFINITI dealer and have the vehicle inspected. Avoid any unnecessary diagnosis during the service by informing the dealer of the condition that may have occurred. Your vehicle has two types of security system, as follows: Theft warning IPPS (Infiniti Personalized Protection System) The security condition will be shown by the security indicator light. CAUTION Continued vehicle operation without having the emission control system checked and repaired as necessary 1-12 INSTRUMENTS AND CONTROLS SECURITY INDICATOR LIGHT dealer for IPPS service as soon as possible. Please bring all IPPS keys that you have when visiting your INFINITI dealer for service. The light will glow for about 30 seconds and then blink. The system is now armed. If, during this 30 second time period, the door or trunk lid is unlocked with a key or multi-remote controller or the ignition key is turned to ``ACC'' or ``ON'', the system will not be armed. However, when the trunk lid is closed after being unlocked with a key or multi-remote controller, the system returns to the armed phase. If the key is turned slowly toward the front of the vehicle when locking the door, the system may not activate. If the key is returned beyond the vertical position toward the rear of the vehicle to remove the key, the system may be deactivated. When the indicator light fails to glow for 30 seconds, unlock the door once and lock it again. Even when the driver and/or passengers are in the vehicle, the system will activate with all doors, hood, THEFT WARNING The theft warning system provides visual and audio alarm signals to deter theft of the vehicle. SII0077 How to arm the theft warning system 1. Close all windows. 2. Remove the key from the ignition switch. 3. Close and lock all doors, hood and trunk lid. The doors can be locked either with a key, multi-remote controller or door lock knob. The system can be armed even if the windows are open. 4. Confirm that the indicator light comes on. 1-13 This light blinks whenever the ignition switch is in the ``LOCK'', ``OFF'' or ``ACC'' position. This function indicates the security systems equipped on the vehicle. Light remains on: When IPPS is malfunctioning, this light will remain on while the ignition key is in the ``ON'' position. If the light still remains on and/or the engine will not start, see your INFINITI INSTRUMENTS AND CONTROLS and trunk lid locked and ignition key off. When turning the ignition to ``ACC'', the system will be released. How to stop alarm The alarm will stop by unlocking a door or trunk lid with the key or by pushing either the unlock or trunk lid release button on the multiremote controller. The alarm will not stop if the ignition switch is turned to ``ACC'' or ``ON''. If the system does not operate as described above, have it checked by your INFINITI dealer. position and wait approximately 5 seconds. 3. Repeat step 1 and 2 again. 4. Restart the engine while keeping the key separate from any other keys on the key-chain. Theft warning system operation The warning system will give the following alarm: The headlights blink and the horn sounds intermittently. The alarm automatically turns off after 2 to 3 minutes; however, the alarm will reactivate if the vehicle is tampered with again. The alarm is activated by: Unlocking the door or opening the trunk lid without using the key or multi-remote controller. (Even if the door is opened by releasing the door inside lock knob or the trunk lid is opened by operating the trunk lid release switch, the alarm is activated.) Opening the hood. WINDSHIELD WIPER AND WASHER SWITCH IPPS (Infiniti Personalized Protection System) The IPPS will not allow the engine to start without the use of the registered IPPS key. If the engine failed to start using the registered IPPS key (for example when keys are contacting), restart the engine using the following procedures: 1. Leave the ignition key in the ``ON'' position for approximately 5 seconds. 2. Turn ignition key to the ``OFF'' or ``LOCK'' 1-14 IIC041-A The windshield wiper and washer operates when the ignition key is in the ``ACC'' or ``ON'' position. INSTRUMENTS AND CONTROLS Push the lever down to operate the wiper. Pull the lever toward you to operate the washer. The intermittent operation time can be adjusted by turning the knob as follows: While driving: from 0.4 to 12 seconds While stopped: from 4 to 20 seconds solution may freeze on the windshield and obscure your vision which may lead to an accident. Warm windshield with the defroster before you wash the windshield. outside door mirrors, start the engine and push the switch on. (The indicator light will come on.) Push the switch again to turn the defogger off. It will automatically turn off in approximately 15 minutes. CAUTION The following could damage the washer system: Do not operate the washer continuously for more than 30 seconds. Do not operate the washer if the reservoir tank is empty. REAR WINDOW AND OUTSIDE DOOR MIRROR DEFOGGER SWITCH CAUTION When cleaning the inner side of the window, be careful not to scratch or damage the rear window defogger. WARNING SII0078 In freezing temperatures the washer To defog the rear window glass and the 1-15 INSTRUMENTS AND CONTROLS HEADLIGHT AND TURN SIGNAL SWITCH Lighting the maximum ``Short'' position, the light will turn off automatically. When the light switch is turned to the '' position, the headlight low or high `` beam will turn off. Turn the switch to the `` '' position: Headlight beam select The parking, side marker, tail, license plate and instrument lights will come on. Turn the switch to the `` '' position: SII0080 SII0079 Headlights will come on and all the other lights remain on. To select the high beam, push the lever forward. Pull it back to select the low beam. Turn the switch to the ``AUTO'' position: When the ignition key is in the ``ON'' position, the parking light, headlight and other lights turn on automatically, depending on the brightness of the surroundings. When the ignition key is turned to the ``ACC'', ``OFF'' or ``LOCK'' position with the autolamp switch in Passing signal Pulling the lever toward you will flash the headlight high beam. 1-16 INSTRUMENTS AND CONTROLS Autolamp switch (Shut-off delay) Photo sensor for autolamp reduced intensity when the engine is started with the parking brake released. The daytime running lights operate with the headlight '' switch in the ``OFF'' position or in the `` position. Turn the headlight switch to the '' position for full illumination when `` driving at night. If the parking brake is applied before the engine is started, the daytime running lights do not illuminate. The daytime running lights illuminate once the parking brake is released. The daytime running lights will remain on until the ignition switch is turned off. SII0081 SII0082 The length of time the autolamps stay on after the ignition key is turned to ``OFF'' while headlight switch is in the ``AUTO'' position depends on how far the autolamp switch is turned. If the switch is turned fully in the above direction, the headlights will stay on for a longer time (a few minutes). Be sure not to put anything on top of the photo sensor located on the top lefthand side of the instrument panel. The photo sensor controls the autolamp; if it is covered, the photo sensor reacts as if it is dark and the headlights will illuminate. WARNING When the daytime running light system is active, tail lights on your vehicle will not be on. It is necessary at dusk to turn on your headlights. Daytime running light system (For Canada) The headlights automatically illuminate at a 1-17 INSTRUMENTS AND CONTROLS Failure to do so could cause an accident injuring yourself and others. or down to the point where lights begin flashing. INSTRUMENT BRIGHTNESS CONTROL FRONT FOG LIGHT SWITCH Turn signal switch SII0085 SII0084 SII0083 Move the lever up or down to signal the turning direction. When the turn is completed, the turn signals cancel automatically. Turn the knob to activate the fog lights. The fog lights can only be activated when the headlight switch is in the `` '' position. The instrument brightness control operates when the light switch is in the `` '' or '' position. `` Turn the control to adjust the brightness of instrument panel lights and power window switch lights. When the control is turned in the upper direction until a click sound is heard, the light intensity will be at maximum. When the control is turned in the lower direction until a Lane change signal To indicate a lane change, move the lever up 1-18 INSTRUMENTS AND CONTROLS click sound is heard, the light will be turned off. HAZARD WARNING FLASHER SWITCH roadway under emergency conditions, move the vehicle well off the road. Do not use the switch while moving on the highway unless unusual circumstances force you to drive so slowly that your vehicle might become a hazard to other traffic. Turn signals do not work when the switch is operating. HEATED SEATS (If so equipped) SII0086 Push the switch on to warn other drivers when you must stop or park under emergency conditions. All turn signal lights will flash. The flasher can be actuated with the ignition switch either off or on. Some state laws may prohibit the use of the hazard warning flasher switch while driving. SII0087 WARNING When stalled or stopped on the The front seats are warmed by built-in heaters. The switches located on the center console can be operated independently of each other. 1. Start the engine. 1-19 INSTRUMENTS AND CONTROLS CAUTION The battery could run down if the heater is operated while the engine is not running. 2. Push the ``LOW'' or ``HIGH'' position of the switch, as desired, depending on the temperature. The indicator light in the switch will illuminate. The heater is controlled by a thermostat, automatically turning the heater on and off. The indicator light will remain on as long as the switch is on. 3. When the vehicle's interior is warmed or before you leave the vehicle, be sure to turn the switch off. CAUTION Do not use the seat heater for a long time or when no one is seated there. Do not put anything on the seat which insulates heat, such as a blanket, cushion, seat cover, etc. Otherwise, the seat may become overheated. Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater. Any liquid spilled on the heating seat should be immediately wiped up with a dry cloth. When cleaning the seat, never use benzine, thinner, or any similar materials. 1-20 If any abnormalities are found or the heating seat does not operate, turn the switch OFF and have the system checked by your INFINITI dealer. TRACTION CONTROL (TCS) CANCEL SWITCH SII0088 To cancel the TCS (traction control system), push the TCS cancel switch on. The indicator INSTRUMENTS AND CONTROLS ``TCS OFF'' will come on. Push it again to turn it ON. See ``Traction control system'' in the ``Starting and driving'' section. CIGARETTE LIGHTERS AND ASHTRAYS Return the lighter to its original position after use. To empty the ashtray, pull up on the horizontal bar and remove the tray. SII0089 The cigarette lighter operates when the ignition switch is in the ``ACC'' or ``ON'' position. Push the lighter in all the way, then release it. When the lighter is heated, it will spring out. SII0090 1-21 INSTRUMENTS AND CONTROLS CUP HOLDER WARNING The cigarette lighter should not be used while driving in order that full attention may be given to the driving operation. CAUTION The cigarette lighter socket is a power source for the cigarette lighter element only. The use of the cigarette lighter socket as a power source for any other accessory is not recommended. SII0092 To open, push the cup holder opener switch. To close, lower the cup holder lid and push down lightly. Use the cup holder properly and according to the size of the cups. The inner cases can be removed for cleaning. SII0091 WARNING The cup holder should not be used 1-22 INSTRUMENTS AND CONTROLS CONSOLE BOX while driving in order that full attention may be given to the driving operation. The dividing plates can be moved to the desired positions. The front part is designed to be used as a card case and coin case. To open the lid, the right and left sides it must be closed securely. Lower part: CAUTION Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger. Use only soft cups in the cup holder. Hard objects can injure you in an accident. SII0093 While pushing up the button, open the cover. WARNING The console box should not be used while driving in order that full attention may be given to the driving operation. Keep the center console box lid closed while driving to prevent injury in an accident or a sudden stop. Upper part: Push the button on the side of the lid to open the upper part sideways. The lid can be opened from the driver and front passenger seats. 1-23 INSTRUMENTS AND CONTROLS POWER WINDOW OPERATING DRIVER'S SWITCH Automatic operation To fully open the driver side window, completely press down the ``AUTO'' switch and release it; it need not be held. The window will automatically open all the way. To stop the window, just pull up the switch toward the ``CLOSE'' side. WARNING Make sure that all passengers have their hands, etc. inside the vehicle before closing the windows. Use the window lock switch to prevent unexpected use of the power windows. Do not leave children unattended inside the vehicle. They could unknowingly activate switches or controls and become trapped in a window. Unattended children could become involved in serious accidents. The power windows only operate when the ignition key is in the ``ON'' position. SII0094A OPERATING PASSENGER'S SWITCH To open or close the window, push down or pull up the switch and hold it. The main switch (driver side switches) will open or close all the windows. Locking passenger's window When the lock button is pushed in, only the driver side window can be opened or closed. Push it in again to cancel. SII0095 The passenger side switch will open or close only the corresponding window. To open or 1-24 INSTRUMENTS AND CONTROLS close the window, hold the switch down or up. Tilting the sunroof To tilt up, first close the sunroof, then keep pushing the ``UP'' side of the tilt switch. To tilt down the sunroof, keep pushing the ``DOWN'' side. SUNROOF (If so equipped) The sunroof will only operate when the ignition key is in the ``ON'' position. CAUTION Remove water drops, snow, ice or sand from the sunroof before opening. Do not place any heavy object on the sunroof or surrounding area. Sliding the sunroof WARNING In an accident you could be thrown from the vehicle through an open sunroof. Always use seat belts and child restraints properly. SII0096 If the sunroof does not close Have your INFINITI dealer check and repair the sunroof. To open the roof, keep pressing the switch to the ``OPEN'' side. To close the roof, keep pressing the switch to the ``CLOSE'' side. Do not allow anyone to stand up or extend any portion of their body out of the opening while the vehicle is in motion or while the sunroof is closing. 1-25 INSTRUMENTS AND CONTROLS CLOCK INTERIOR LIGHT The interior light switch has a three-position. -- remain on for a maximum of 30 seconds after driver's door is closed. ignition key is removed from key cylinder. -- remain on for a maximum of 30 seconds. The lights will go off when the ignition key is in the ``ACC'' or ``ON'' position, or the driver's door is closed and locked. SII0097 The lights will also go off after 30 minutes while doors are open. SII0098 The digital clock displays time when the ignition key is in ``ACC'' or ``ON''. If the power supply is disconnected, the clock will not indicate the correct time. Readjust the time. While the switch is in the center `` '' position, the front and rear personal, console and foot well lights will illuminate under the following conditions: driver's door is unlocked. -- remain on for a maximum of 30 seconds. driver's door is opened. 1-26 When some doors are opened, the door step light for each open door will come on and the closed door's personal lights will darken. Adjusting the time Push the ``H'' button to adjust the hour. Push the ``M'' button to adjust the minute. INSTRUMENTS AND CONTROLS CAUTION Leaving the interior light switch in the ON position for extended periods of time will result in a discharged battery. light will turn on. When the switch is pushed again, the light will turn off. lights turn off immediately. 3 When the switch is pressed, both right and left lights come on. * The switches face forward in the vehicle. If the interior light switch is in OFF position, the personal light will not turn on when the any of the doors are opened. PERSONAL LIGHT SII0100 The lights will turn on/off depending on what side of the switch is pressed: 1 The light stays on when pressed to this position. 2 When the front door is opened, both the SII0099 When the switch is pushed in with the interior light switch in the center `` '' position, the right and left seat lights come on. They turn off when the door is closed. When the rear door is opened both left and right lights come on. When it is closed, the 1-27 INSTRUMENTS AND CONTROLS VANITY MIRROR LIGHT INTEGRATED HomeLink TRANSMITTER The Integrated HomeLink Transmitter provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. WARNING Do not use this Integrated HomeLink Transmitter with any garage door opener that lacks safety stop and reverse features as required by federal safety standards (these standards became effective for models manufactured after April 1, 1982). A garage door opener which cannot ``detect'' an object in the path of a closing garage door and then automatically stop and reverse the door, does not meet current federal safety standards. Using a garage door opener without these features increases the risk of serious injury or death. THE INTEGRATED HomeLink TRANSMITTER: SII0101 The light on the vanity mirror will turn on when the cover on the vanity mirror is opened. will operate garage doors, gates, home/ office lighting systems and security systems by storing and transmitting the programming information of your current hand-held transmitters. is built-in and powered by your vehicle's battery and charging system. No separate batteries are necessary. 1-28 INSTRUMENTS AND CONTROLS programming. Your vehicle's engine should be turned off while programming your transmitter. The Integrated HomeLink Transmitter may not work with older garage door openers that do not meet current Federal Consumer Safety Standards. 1. Test the Integrated HomeLink Transmitter by pressing any button. The red indicator light should come on. If you have previously programmed a button proceed to step 3. 2. Clear all channels on the Integrated HomeLink Transmitter by holding down both outside buttons (#1 & #3) until the red light begins to flash rapidly (approximately 20 seconds). Then release both buttons. 1-29 3. Select which of the three Integrated HomeLink Transmitter buttons you want to program. 4. Hold your hand-held transmitter against the bottom surface of the Integrated HomeLink Transmitter so that you can still see the red indicator light. 5. Press the desired button until the red indicator light flashes slowly. Do not release the button. Continue holding and press the hand-held transmitter button through step 6. 6. Hold down both buttons until the red indicator light on the Integrated HomeLink Transmitter flashes rapidly (This may take 1 to 90 seconds). Then release both buttons. The rapid flashing means that the transmitter has been successfully programmed to match your hand-held transmitter. You can now use the Integrated HomeLink Transmitter in- SII0102 PROGRAMMING THE HomeLink TRANSMITTER WARNING During the programming procedure your garage door or security gate will open and close (if the transmitter is within range). Make sure that people or objects are clear of the garage door, gate, etc. that you are INSTRUMENTS AND CONTROLS stead of your hand-held transmitter. Note to Canadian users: Prior to 1992, D.O.C. regulations required many hand-held transmitters to stop transmitting after one or two seconds, even though you continue to hold down the button. If you think you have one of these hand-held transmitters, you should press and re-press the transmitter button every 2 seconds without ever releasing the integrated HomeLink Transmitter button. The indicator light on the Integrated HomeLink Transmitter should blink rapidly indicating a successful programming procedure. If it returns to the slow blink of program mode, continue to periodically reactivate your hand-held transmitter until a successful programming procedure is indicated by the rapidly flashing indicator light. button on the Integrated HomeLink Transmitter. The red indicator light illuminates while the signal is being transmitted. The effective transmission range of the Integrated HomeLink Transmitter may differ from your hand-held transmitter. over-end and program again. For best results, place the end opposite the battery compartment against the Integrated HomeLink Transmitter when programming. PROGRAMMING PROBLEM DIAGNOSIS Be sure to keep your original hand-held transmitter for possible reprogramming if necessary. Make sure batteries in the hand-held transmitter are fully charged. Hold your hand-held transmitter against the bottom surface of the Integrated HomeLink Transmitter so that you can still see the red indicator light. Hold buttons for duration of the programming without interruption. Rotate your hand-held transmitter end1-30 SIP0198 ROLLING CODES (If so equipped) If your hand held transmitter appears to train to the HomeLink Transmitter, but does not open your garage door, and your garage door opener was manufactured after 1995, your garage door opener may have a ``Code OPERATING THE TRANSMITTER To operate, simply press the appropriate INSTRUMENTS AND CONTROLS Protected'' or ``Rolling Code'' feature. This type of system will change the ``code'' of your garage door opener every time you open or close your garage door. To determine if you have one of these systems, depress the button on the HomeLink Transmitter that you have just programmed. If the LED on the HomeLink Transmitter flashes rapidly for 1 to 2 seconds, then remains on, your garage door opener has a rolling code system. To operate your ``Rolling Code'' garage door opener from your HomeLink Transmitter, follow these steps: 1. Program your hand held transmitter to the HomeLink Transmitter by following the procedures outlined above (if not yet programmed). 2. Program your garage door opener receiver to recognize your HomeLink Transmitter (The HomeLink Transmitter follows the same procedure to train to the receiver as your hand held transmitter did when it was first installed): a) Remove the cover panel from your garage door opener receiver. The receiver should be located by the garage door opener motor. Locate the training button on the garage door opener receiver. The exact location and color of the button may vary by garage door opener brand. If you have difficulty locating the training button, reference your garage door opener manual. If you have difficulty programming your garage door opener equipped with a rolling code system to recognize the HomeLink Transmitter with the ``Rolling Code'' feature, call INFINITI Consumer Affairs Department. Press the training button on the ga1-31 rage door opener receiver for 1 to 2 seconds. d) Return to the HomeLink Transmitter in the vehicle, and depress the programmed HomeLink button for the duration of the fast blink on the HomeLink Transmitter (1 to 2 seconds). Release the button, and repress to confirm that the system has trained. Your garage door opener should now recognize your HomeLink Transmitter. You may use either your HomeLink Transmitter or your original hand held transmitter to open your garage door. b) e) CLEARING THE PROGRAMMING INFORMATION Should you sell your vehicle, be sure to clear the channels of the Integrated HomeLink Transmitter. To clear the channels, simulta- c) INSTRUMENTS AND CONTROLS neously hold down the outside two buttons (#1 & #3) until the red indicator light begins to flash rapidly (approximately 20 seconds). This will clear all three buttons. Individual buttons cannot be cleared, but can be reprogrammed at any time by following the programming procedures described above. part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference that may be received, including interference that may cause undesired operation. The transmitter has been tested and complies with FCC and DOC/MDC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the device. DOC: ISTC 1763K1313 FCC I.D.: CB2V67690 IF YOUR VEHICLE IS EVER STOLEN If your vehicle has been stolen, you should change the codes of any device that was programmed into the Integrated HomeLink Transmitter as soon as possible. Consult the owners manual of each device, or call the manufacturer or dealer of those devices. When your vehicle is recovered, you will need to reprogram the Integrated HomeLink Transmitter with your new transmitter information. FCC Notice: This device complies with FCC rules 1-32 2 PRE-DRIVING CHECKS AND ADJUSTMENTS Key ............................................................. 2-2 Door locks .................................................. 2-3 Multi-remote control system ...................... 2-5 Hood release .............................................. 2-9 Glove box lock .......................................... 2-10 Trunk lid lock ........................................... 2-10 Fuel filler lid lock ...................................... 2-11 Seats ........................................................ 2-13 Supplemental restraint system ................. 2-16 Seat belts ................................................. 2-29 Child restraints for infants and small children ............................................ Automatic drive positioner ........................ Tilting steering column ............................ Telescopic steering column ..................... Outside mirror remote control ................. Foldable outside mirrors .......................... Automatic anti-dazzling inside mirror ...... Sun visors ................................................ 2-37 2-45 2-47 2-48 2-48 2-49 2-49 2-50 PRE-DRIVING CHECKS AND ADJUSTMENTS KEY wallet key cannot be used to drive your vehicle.) The master key and wallet key can be used for all locks. When the key case with the wallet key is placed into your wallet, be careful not to apply excessive force to the wallet as it or other cards could be damaged. The security key cannot be used for the trunk lid or glove box locks. To protect belongings when you leave a key with someone, give them the security key only. Never leave these key in the vehicle. Record the key number on the key number plate supplied with your keys and keep it in a safe place (such as your wallet), NOT IN THE VEHICLE. INFINITI does not record any key number so it is very important to keep track of 2-2 your key number plate. A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, this key can be duplicated by your INFINITI dealer. IPPS KEY - Master and Security keys: The key number is necessary when you need extra IPPS keys. As many as 5 IPPS keys can be used with one vehicle. New keys must be registered to the IPPS components in your vehicle by your INFINITI dealer. At this time, you should bring all IPPS keys that you have to your INFINITI dealer for registration. This is because the registration process will erase all memory of the IPPS components. SIP0091 You can only drive your vehicle using the master or security keys which are registered to the IPPS (Infiniti Personalized Protection System) components in your vehicle. These keys have a transponder chip in the key head. (The PRE-DRIVING CHECKS AND ADJUSTMENTS DOOR LOCKS Locking front doors with key Locking the doors without key WARNING Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally opening the doors, and will help keep out intruders. Before opening any door, always look for and avoid oncoming traffic. Do not leave children unattended inside the vehicle. They could unknowingly activate switches or controls. Unattended children SIP0092 SIP0180 To lock the door, turn the key toward the front of the vehicle. To unlock, turn it toward the rear. Locking the front door will simultaneously lock the other doors. To lock the doors from the outside without a key, move the inside lock knob to the ``LOCK'' position, then close the door. When locking the door this way, be certain not to leave the key inside the vehicle. The inside lock knob of the front door cannot be set to the ``LOCK'' position with front door opened and with the key in the ignition. If this is attempted, all doors will unlock. 2-3 PRE-DRIVING CHECKS AND ADJUSTMENTS could become involved in serious accidents. the rear door can be opened only from the outside. only be removed and inserted.) and turning it to the rear again within 3 seconds will unlock all doors. Pushing the front door lock knob in will lock all doors. If the front doors are open with the key in the ignition when the inside lock knob is set to the lock position, all door knobs will unlock. When the open front door is closed, all the knobs will lock then quickly unlock automatically. POWER DOOR LOCK The power door lock system allows you to lock or unlock all doors simultaneously. CHILD SAFETY REAR DOOR LOCK SIP0181 SIP0005 Child safety locking helps prevent doors from being opened accidentally, especially when small children are in the vehicle. When the lever is in the lock position, Turning the front door key to the front of the vehicle will lock all doors. Turning the front door key one time to the rear of the vehicle will unlock the corresponding door. From that position, returning the key to Neutral (where the key can 2-4 SIP0093 PRE-DRIVING CHECKS AND ADJUSTMENTS Operating the lock-unlock switch will lock or unlock all doors. MULTI-REMOTE CONTROL SYSTEM It is possible to lock/unlock all doors, to release the trunk lid and to activate the panic alarm by using the remote controller from outside the vehicle. Before locking the doors, make sure the key is not left in the vehicle. The remote controller can operate at a distance of approximately 33 ft (10 m) from the vehicle. (The effective distance depends upon the conditions around the vehicle.) As many as four remote controllers can be used with one vehicle. For information concerning the purchase and use of additional remote controllers, contact your INFINITI dealer. CAUTION Listed below are conditions or occurrences which will damage the remote controller. Do not allow the remote controller to become wet. Do not drop the remote controller. Do not strike the remote controller sharply against another object. Do not place the remote controller for an extended period in an area where temperatures exceed 140°F (60°C). WARNING Before opening the door, always look for and avoid oncoming traffic. Do not leave children unattended inside the vehicle. They could unknowingly activate switches or controls. Unattended children could become involved in serious accidents. 2-5 PRE-DRIVING CHECKS AND ADJUSTMENTS HOW TO USE MULTI-REMOTE CONTROL SYSTEM Locking doors 1. Remove the ignition key. 2. Close all doors. 3. Push the lock button on the remote controller. 4. All doors will lock. 5. The hazard indicator flashes twice. When the lock button is pushed with all doors locked, the hazard indicator flashes twice as a reminder that the doors are already locked. SIP0094 2-6 PRE-DRIVING CHECKS AND ADJUSTMENTS Unlocking doors 1. Push the unlock button on the remote controller. 2. Only the driver side door will unlock. Push the unlock button on the remote controller again within 5 seconds. 3. All doors will unlock. 4. The interior light will stay on for 30 seconds after unlocking the driver side door when the interior light switch is in the center `` '' position. The interior light can be turned off without waiting for 30 seconds by inserting the key into the ignition, then turning to the ``ACC'' position or by locking the doors. The trunk will not open with the trunk lid release cancel switch turned to OFF . (See ``Trunk lid lock'' for details.) Using the panic alarm If you are near your vehicle and feel threatened, you may activate the alarm to call attention as follows: 1. Push the panic alarm button on the remote controller. 2. The theft warning alarm and headlight will stay on for 30 seconds. 3. The alarm will stop when any of the key functions are used except the panic alarm button. Releasing the trunk lid 1. Push the trunk lid release button for longer than 0.5 seconds. 2. The trunk lid will open. 2-7 SIP0086 BATTERY REPLACEMENT Replace the battery as follows: PRE-DRIVING CHECKS AND ADJUSTMENTS 1. Open the lid using a suitable tool. 2. Replace the battery with a new one. Recommended battery: CR2025 or equivalent 3. Close the lid securely. 4. Press the key button two or three times to check its operation. If the battery is removed for any reason other than replacement, perform step 4 above. An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal. The remote controller is waterproof; however, if it does get wet, immediately wipe completely dry. The operational range of the remote controller extends to approximately 33 ft (10 m) from the vehicle. 2-8 This range may vary with conditions. FCC Notice: Changes or modifications not expressly approved by the manufacturer compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. PRE-DRIVING CHECKS AND ADJUSTMENTS HOOD RELEASE from the engine compartment, to avoid injury, do not open the hood. SIP0095 1. Pull the hood lock release handle located below the instrument panel; the hood will then spring up slightly. 2. Pull the lever at the front of the hood with your fingertips and raise the hood. 3. When closing the hood, slowly close the hood and make sure it locks into place. WARNING Make sure the hood is completely closed and latched before driving. Failure to do so could cause the hood to fly open and result in an accident. If you see steam or smoke coming 2-9 PRE-DRIVING CHECKS AND ADJUSTMENTS GLOVE BOX LOCK CAUTION Keep the glove box lid closed while driving to help prevent injury in an accident or a sudden stop. TRUNK LID LOCK SIP0096 SIP0097 Trunk lid release switch operation The trunk lid release switch is located under the driver's armrest. When locking or unlocking the glove box, use the master key and wallet key. The glove box may be opened by pulling the handle. To open the trunk lid, pull the release switch. To close, push the trunk lid down securely. 2-10 PRE-DRIVING CHECKS AND ADJUSTMENTS Key operation and driving'' section.