User manual PIONEER AVH-P5750DVD - 1

Connecting the Units WARNING CAUTION: · PIONEER does not recommend that you install or service your display yourself. Installing or servicing the product may expose you to risk of electric shock or other hazards. Refer all installation and servicing of your display to authorized Pioneer service personnel. · Secure all wiring with cable clamps or electrical tape. Do not allow any bare wiring to remain exposed. · To avoid the risk of accident and the potential violation of applicable laws, the front DVD or TV (sold separately) feature should never be used while the vehicle is being driven. Also, Rear Displays should not be in a location where it is a visible distraction to the driver. · In some countries or states the viewing of images on a display inside a vehicle even by persons other than the driver may be illegal. Where such regulations apply, they must be obeyed and this unit's DVD features should not be used. ENGLISH> Note: · This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recreational vehicle, truck, or bus, check the battery voltage. · To avoid shorts in the electrical system, be sure to disconnect the battery cable before beginning installation. · Refer to the owner's manual for details on connecting the power amp and other units, then make connections correctly. · Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts. · Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, handbrake and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body. · Don't pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short. · Do not shorten any leads. If you do, the protection circuit may fail to work when it should. · Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating. · When replacing the fuse, be sure to only use a fuse of the rating prescribed on the fuse holder. · Since a unique BPTL circuit is employed, never wire so the speaker leads are directly grounded or the left and right speaker leads are common. · If the RCA pin jack on the unit will not be used, do not remove the caps attached to the end of the connector. · Speakers connected to this unit must be highpower with minimum rating of 50 W and impedance of 4 to 8 ohms. Connecting speakers with output and/or impedance values other than those noted here may result in the speakers catching fire, emitting smoke or becoming damaged. · When this product's source is switched ON, a control signal is output through the blue/white lead. Connect to an external power amp's system remote control or the car's Auto-antenna relay control terminal (max. 300 mA 12 V DC). If the car features a glass antenna, connect to the antenna booster power supply terminal. · When an external power amp is being used with this system, be sure not to connect the blue/white lead to the amp's power terminal. Likewise, do not connect the blue/white lead to the power terminal of the auto-antenna. Such connection could cause excessive current drain and malfunction. · To avoid a short-circuit, cover the disconnected lead with insulating tape. Insulate the unused speaker leads without fail. There is a possibility of a short-circuit if the leads are not insulated. · To prevent incorrect connection, the input side of the IP-BUS connector is blue, and the output side is black. Connect the connectors of the same colors correctly. · This unit cannot be installed in a vehicle that does not have an ACC (accessory) position on the ignition switch. (Fig. 1) ACC INSTALLATION MANUAL AVH-P5750DVD · It is extremely dangerous to allow the display lead to become wound around the steering column or gearshift. Be sure to install the display in such a way that it will not obstruct driving. · Make sure that wires will not interfere with moving parts of the vehicle, such as the gearshift, parking brake or seat sliding mechanism. · Do not shorten any leads. If you do, the protection circuit may fail to work properly. WARNING This product conforms to new cord colors. LIGHT GREEN LEAD AT POWER CONNECTOR IS DESIGNED TO DETECT PARKED STATUS AND MUST BE CONNECTED TO THE POWER SUPPLY SIDE OF THE PARKING BRAKE SWITCH. IMPROPER CONNECTION OR USE OF THIS LEAD MAY VIOLATE APPLICABLE LAW AND MAY RESULT IN SERIOUS INJURY OR DAMAGE. ACC position No ACC position · The black lead is ground. Please ground this lead separately from the ground of high-current products such as power amps. If you ground the products together and the ground becomes detached, there is a risk of damage to the products or fire. · Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied manuals of both products and connect cords that have the same function. Printed in Japan RC <05A00000> T T · Do not drill a hole into the engine compartment to connect the yellow lead of the unit to the vehicle battery. Engine vibration may eventually cause the insulation to fail at the point where the wire passes from the passenger compartment into the engine compartment. Take extra care in securing the wire at this point. OF OF F O N F O N STAR STAR Fig. 1 Connecting the Units Connecting the power cord When connecting to separately sold power amp 15cm Antenna cable IP-BUS input (Blue) This product Multi-CD player (sold separately) IP-BUS cable Subwoofer output or non fading output (SUBWOOFER OUTPUT or NON-FADING OUTPUT) 23 cm This product Power amp (sold separately) 15cm Yellow/black If you use a cellular telephone, connect it via the Audio Mute lead on the cellular telephone. If not, keep the Audio Mute lead free of any connections. Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF. Fuse resistor Connection method 1. Clamp the lead. 2. Clamp firmly with f needle-nosed pliers. Front output (FRONT OUTPUT) RCA cables (sold separately) Power amp (sold separately) 15 cm Note: · The position of the parking brake switch depends on the vehicle model. For details, consult the vehicle Owner's Manual or dealer. Light green Used to detect the ON/OFF status of the parking brake. This lead must be connected to the power supply side of the parking brake switch. Blue/white To system control terminal of the power amp (max. 300 mA 12 V DC). When you connect the separately sold multi-channel processor (e.g. DEQ-P7650) to this unit, do not connect anything to the speaker leads and system remote control (blue/white). Note: When you connect the multi-channel processor to this unit, a separately sold power amp must be connected to the multi-channel processor. Note: Change the initial setting of this product (refer to the Operation Manual). The subwoofer output of this unit is monaural. System remote control Violet/white Of the two lead wires connected to the back lamp, connect the one in which the voltage changes when the gear shift is in the REVERSE (R) position. For details, see Fig. 4 Yellow To terminal always supplied with power regardless of ignition switch position. Fuse holder Left Front speaker + + Right Front speaker Power supply side Ground side Parking brake switch Black (ground) To vehicle (metal) body . White Gray + Front speaker Left Rear speaker + Green/black Violet/black White/black Green Gray/black Violet + Right Rear speaker Subwoofer + + Subwoofer + Front speaker Blue/white To system control terminal of the power amp or Auto-antenna relay control terminal (max. 300 mA 12 V DC). With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers. When you connect the separately sold multi-channel processor (DEQ-P7650) to this unit, do not connect anything to the speaker leads and system remote control (blue/white). Perform these connections when using the optional amplifier. Fig. 2 Fig. 3 Connecting the Units When connecting with a rear view camera When using this product with a rear view camera, automatic switching to video from a rear view camera when the gear shift is moved to REVERSE (R) position is possible. WARNING USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY RESULT IN INJURY OR DAMAGE. Blue Blue IP-BUS input (Blue) 15 cm This unit 15 cm IP-BUS input (Blue) Subwoofer output or non fading output (SUBWOOFER OUTPUT or NON-FADING OUTPUT) F FADING RCA cable (supplied with multi-channel processor) Optical cable (supplied with multi-channel processor) Yellow 26 pin cable (supplied with Vehicle Dynamics Processor) Vehicle Dynamics Processor (e.g. AVG-VDP1) (sold separately) When connecting with a multi-channel processor AV-BUS input (Blue) 40 cm RCA cable (supplied with DVD player) Video input When connecting with Vehicle Dynamics Processor and an iPod adapter Connecting and installing the optical cable connection box WARNING · Avoid installing this unit in such a location where the operation of safety devices such as airbags is prevented by this unit. Otherwise, there is a danger of a fatal accident. · Avoid installing this unit in such a location where the operation of the brake may be prevented. Otherwise, it may result in a traffic accident. · Fix this unit securely with the velcro tape or lock tie. If this unit is loose, it disturbs driving stability, which may result in a traffic accident. 26 pin cable input Optical cable CAUTION · The screen image may appear reversed. · The rear view camera function is to use this product as an aid to keep an eye on trailers, or backing into a tight parking spot. Do not use this function for entertainment purposes. · The object in rear view may appear closer or more distant than in reality. Fig. 8 This product IP-BUS cable (supplied with 23 cm multi-channel processor) Installing the optical cable connection box · When installing the optical cable connection box with the velcro tape. (Fig. 9) Install the optical cable connection box using the velcro tape in the ample space of the console box. CAUTION IP-BUS cable · Install this unit using only the parts supplied with this unit. If other parts are used, this unit may be damaged or could dismount itself, which leads to an accident or trouble. · Do not install this unit near the doors where rainwater is likely to be spilled on the unit. Incursion of water into the unit may cause smoke or fire. CAUTION This unit 20 cm Rear view camera in RCA cable (sold separately) You must use a camera which outputs mirror reversed images. Black Optical cable connection box (supplied) IP-BUS cable (Supplied with the iPod adapter) 1.5 m Black Blue iPod adapter (e.g. CD-IB100) iPod, iPod mini or iPod Photo Connecting the optical cable Velcro tape (hard) rear view camera To video output Blue Optical cable (sold separately) Multi-CD player (sold separately) 1.5 m Dock connector (Supplied with the iPod adapter) 1. Connect the optical cable and ground lead to the main unit. (Fig. 7) Connect the optical cable so that it does not protrude from the unit, as shown in the illustration. Fasten the ground lead to the protrusion on the back of the unit. Screw Velcro tape (soft) Extension lead (supplied) 15 cm 8m Fuse resistor Multi-channel processor (DEQ-P7650) (sold separately) V Violet/white Of the two lead wires connected to the back lamp, connect the one in which the voltage changes when the gear shift is in the REVERSE (R) position. This connection enables the unit to sense whether the car is moving forwards or backwards. Connection method 1. Clamp the lead. DVD Player (e.g. XDV-P9-- or SDV-P7) (sold separately) IP-BUS output (Black) Dock connector port To video output (FRONT VIDEO OUTPUT) Blue Fig. 9 · When installing the optical cable connection box with the lock tie. (Fig. 10) Wrap the optical cable and connection box with the protection tape and fasten with the power code using the lock tie. Wrap with the protection tape Black Blue IP-BUS cable (supplied with TV tuner) Black IP-BUS cable Blue Multi-CD Player (sold separately) Hide-away TV tuner (e.g. GEX-P5750TVP) (sold separately) 2. Clamp firmly with f needle-nosed pliers. Fig. 7 When you connect a separately sold DVD player to the separetely sold multi-channel processor, the optical cable from DVD player must be connected to the optical cable 2 input (OPT. IN2) of the multi-channel processor. Note: · It is necessary to set B-CAM to ON in SET UP when connecting the rear view camera. AV-BUS cable (supplied with TV tuner) Black 2. Connect the optical cable to the optical cable connection box. (Fig. 8) Fasten with the lock tie Fig. 4 Fig. 5 Fig. 6 Fig. 10 Installation When connecting the external video component and the display Note: · Before finally installing the unit, connect the wiring temporarily, making sure it is all connected up properly, and the unit and the system work properly. · Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. · Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. · Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop. · Do not install the display where it may (i) obstruct the driver's vision, (ii) impair the performance of any of the vehicle's operating systems or safety features, including air bags, hazard lamp buttons or (iii) impair the driver's ability to safely operate the vehicle. · The semiconductor laser will be damaged if it overheats, so don't install the unit anywhere hot -- for instance, near a heater outlet. · If installation angle exceeds 30° from horizontal, the unit might not give its optimum performance. (Fig. 12) Installing the remote control unit When not using the remote control unit, secure it with velcro tape to prevent it from moving. DIN Front/Rear-mount This unit can be properly installed either from "Front" (conventional DIN Front-mount) or "Rear" (DIN Rearmount installation, utilizing threaded screw holes at the sides of unit chassis). For details, refer to the following illustrated installation methods. DIN Rear-mount Installation using the screw holes on the side of the unit Conceal tape Side bracket Flush surface screw (5 × 6 mm) Screw This unit Video input Audio input RCA cables (sold separately) To video output External video component (sold separately) · Thoroughly wipe off the surface before affixing the velcro tape. Remote control unit Velcro tape (small) (hard) Velcro tape (small) (soft) · Fastening the unit to the factory radio mounting bracket. (Fig. 18) (Fig. 19) (Fig. 20) Select a position where the screw holes of the bracket and the screw holes of this product become aligned (are fitted), and tighten the screws at 2 places on each side. Use any of binding screws (4 × 3 mm), binding screws (5 × 6 mm) or flush surface screws (5 × 6 mm), depending on the shape of the screw holes in the bracket. Factory radio mounting bracket Before installing the unit · Remove the frame and the holder. (Fig. 15) Pull out to remove the frame and then loosen the screws (2 × 3 mm) to remove the holder. (When reattaching the frame, point the side with a groove downwards and attach it.) Dashboard or Console Video output Multi-DVD Player (sold separately) Fig. 16 2. Install the unit into the dashboard. (Fig. 17) After inserting the holder into the dashboard, then select the appropriate tabs according to the thickness of the dashboard material and bend them. (Install as firmly as possible using the top and bottom tabs. To secure, bend the tabs 90 degrees.) Dashboard Fig. 20 Video output To audio outputs RCA cables (sold separately) Fixing the front panel If you do not operate the removing and attaching the front panel function, use the supplied fixing screws to fix the front panel to this unit. Audio output Fig.14 *1 Use binding screws (4 × 3 mm) only. RCA cable (sold separately) To video input Display with RCA input jacks Holder *1 *1 · Fix the front panel to the unit using fixing screws after removing the front panel. (Fig. 21) Fig. 11 · It is necessary to set AV INPUT to VIDEO in SET UP when connecting an external video component. · It is necessary to set AV INPUT to M-DVD in SET UP when connecting a multi-DVD player. 30° Screw (2 × 3 mm) Frame 182 Fig. 15 Fig. 12 · The cords must not cover up the area shown in the figure below. This is necessary to allow the amplifires to radiate freely. (Fig. 13) 53 Rubber bush Screw Fig. 18 · When installing in a shallow space, use the following screw holes. In this case, stick conceal tape on parts that protrude from the dashboard. Conceal tape When using a display connected to rear video output This product's rear video output is for connection of a display to enable passengers in the rear seats to watch the DVD or Video CD. WARNING: · NEVER install the display in a location that enables the Driver to watch the DVD or Video CD while Driving. DIN Front-mount Holder Fixing screw Installation with the rubber bush 1. Decide the position of the side brackets. (Fig. 16) When installing in a shallow space, change the position of side brackets. In this case, stick conceal tape on parts that protrude from the dashboard. Side bracket Screw (2 × 3 mm) *1 *1 Fig. 21 Do not close this area. · After installing the unit into the dashboard, reattach the frame. Fig. 17 Fig. 19 Fig. 13 ÷ OF OF F ACC O N STAR F O N STAR T T + + + + + + + + ÷ *1 *1 30° 182 53 *1 *1