ROC3205 User manual ROC 3205 ROC 3205 This universal remote control is compatible with the majority of television sets, DVD players, satellite receivers and infrared controlled cable. This remote control has already been programmed so that you can use it to control most of the audio/video products made by the THOMSON group. Before attempting to programme the remote control, try it out by using one of the methods described in this user manual.The two CR2032 batteries are already fitted in the remote control. Refer to the diagram on the cover to replace them when they are worn out. Please keep this guide along with the code list (provided separately), so that you can programme your remote control for use with other products. 1 - Description of the key functions 1 2 Indicator lamp: the red indicator lamp lights up when any key is pressed. Product keys (TV, DVD or SAT): Used to programme and control different products (TV, satellite receiver, DVD player and so on). SHIFT: activates the secondary key features (indications in blue). VOL-, VOL+ Increases (+) or decreases (-) the volume of the TV set; SHIFT + C/B: also allows you to navigate the menus horizontally. :Teletext On/Off in TV mode. SHIFT + MENU: turns on the menu of the selected products G (rewind): Goes backward or advances forward (DVD)*. RECORD: To record, press the RECORD key twice. Stop the disc (DVD)*. Number keys 0 to 9: these keys have the same functions as those of your original remote and are also used to enter the codes for different products. : stop page scrolling (videotext). SETUP: Programmes the remote control. POWER: On/Standby. AV: For selecting an external source (SCART). PROG+, PROG-: Programmes zapping button (received by the television set or the satellite receiver); use to scroll vertically through menus. SHIFT + / : also allow you to navigate the menus vertically. MUTE: Switches the TV sound off. SHIFT + OK: confirms a selection. :Teletext Off in TV mode. SHIFT + EXIT: turns off the menu of the selected product. B (play): play a DVD disc DVD*. F: fast forward (DVD)*. K: Suspends play and stops on an image*. :Videotext inlay on TV picture. Press this key first before you type in the 2-digit channel number (except for Thomson group products). C B 2. Press the product key (2) that corresponds to the type of product you want to control: TV: television set, DVD: DVD player, SAT: satellite receiver. 3. Point the remote control towards the product and try to turn it off by pressing the POWER (12) key. If the product doesn't turn off, you'll need to programme the remote control by one of the methods described in chapter 3. 3 4 3 - Programming the remote control Method A ­ Fast programming with 1-digit subcode Before you start programming, you must find the subcode of the product to be controlled (television set, satellite receiver or DVD player). Refer to the list provided with these instructions, page I of the codes. 1. Turn on the product you want to control. 2. Hold down the SETUP (11) key until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). 3. Press the product key (2) that corresponds to the type of product you want to control: TV: television set, DVD: DVD player, SAT: satellite receiver. 4. While the indicator is lit, type in the subcode (example: 1 for THOMSON). 5. Point the remote towards the product and try to turn it off by pressing the POWER (12) key. 6. If the product you want to control turns off, press the MUTE (15) key to save the subcode. 7. If the product doesn't turn off, press the POWER (12) key repeatedly until the set switches off. Wait approximately one second between key presses to give the red indicator lamp (1) enough time to go off and light up again. This will allow you to see whether the product responds or not. 8. Immediately after the product to be controlled turns off, press the MUTE (15) key to save the subcode. Note: If you want to assign another type of product than those mentioned on the remote control (with the exception of the TV button which can only be used to control a television set), begin by entering the code that corresponds to the product you want to programme (a 3-digit code that you will find in the code booklet ­ see method B). Example: if you want to control a satellite receiver with the DVD key, begin by entering a satellite code (any satellite, for example: 603 for a Thomson satellite receiver) then begin the procedure. 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 * The coloured buttons can be used to select categories when teletext is activated, and specific functions depending on the make. 2 - Testing the remote control before you programme it 1. Turn on the product you want to control. 1 EN Checking the programming: Your product should be ready to receive remote control commands. Check to see that your remote functions correctly by performing the test described on page 3. Method B - 3-digit codes programming Before you start programming, you must find the code for the product to be controlled (television set, satellite receiver or DVD player). Refer to the list provided with these instructions, on page II of the codes. 1. Turn on the product you want to control. 2. Hold down the SETUP (11) until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). 3. Press the product key (2) that corresponds to the type of product you want to control: TV: television set, DVD: DVD player, SAT: satellite receiver. 4. While the indicator is lit, enter the 3-digit code proposed for the product to be controlled (example: 036 for THOMSON). The red indicator then goes off if the code is correct or flashes, if the code is not on the list. 5. Point the remote control towards the product and try to turn it off by pressing the POWER (12) key. 6. If the product doesn't turn off, repeat step 2, using the next 3-digit code in the list. Try to turn off the product by pressing POWER (12) key once. Repeat this procedure until one of the 3-digit codes works. Checking the programming: Your product should be ready to receive remote control commands. Check to see that your remote functions correctly by performing the test described on page 3. Method C - Programming by means of code retrieval If none of the codes work, you may still be able to retrieve the appropriate code. 1. Turn on the product you want to control. 2. Hold down the SETUP (11) key until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). 3. Press the product key (2) that corresponds to the type of product you want to control: TV: television set, DVD: DVD player, SAT: satellite receiver. 4. Point the remote control towards the product and try to turn it off by pressing the POWER (12) key. 5. If the appliance to be controlled switches off, press the MUTE (15) key to memorise the code. 6. If the product does not turn off, press the POWER (12) key until the product switches off (up to 200 times).Wait approximately one second between key presses to give the red indicator lamp (1) enough time to go off and light up again.This will allow you to see whether the product responds or not. 7. Immediately upon turning off the product to be controlled, press the MUTE (15) key to save the code. Note: If you want to assign another type of product than those mentioned on the remote control, begin by entering a code that corresponds to the product you want to programme (a 3-digit code that you will find in the code booklet ­ see method B). Example: if you want to control a satellite receiver with the DVD key, begin by entering a satellite code (any satellite, for example: 603 for a Thomson satellite receiver) then begin the procedure. Checking the programming: Your product should be ready to receive remote control commands.Check to see that your remote functions correctly by performing the test described on page 3. Method D - Automatic code search With this method, the remote scrolls through the full code list by sending an IR signal to the product to be controlled remotely. 1. Check that your product is on. If not, turn it on manually. 2. Hold down the SETUP (11) key until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). 3. Release the SETUP key. 4. Press the product key (2) corresponding to the type of product you want to control: (for example TV). 5. Press PROG+ (14). After a few seconds, the remote begins to scroll through the code list at approximately 1 code per second. Press PROG+ (14) once again to slow down the test speed (1 code every 3 seconds). As soon as the product changes channels, press the MUTE (15) key to save the code and stop the remote from scrolling through the list. If you have gone past the code, you can go back to the previous code by pressing PROG- (14) as many times as necessary (you can go forward by pressing POWER (12) or PROG+ (14). As soon as the product responds again, press the MUTE (15) key to save the code. Note: If you want to assign another type of product than those mentioned on the remote control, begin by entering a code that corresponds to the product you want to programme (a 3-digit code that you will find in the code booklet ­ see method B). Example: if you want to control a satellite receiver with the DVD key, begin by entering a satellite code (any satellite, for example: 603 for a Thomson satellite receiver) then begin the procedure. Method E - Programming for control of a COMBO TV/VCR,TV/DVD) Depending on the COMBO group (TV/VCR,VCR/DVD, etc.) and the make, you will be required to enter a single code for both devices in the COMBO, or to enter two codes, one code per device. Consult the separate list to discover this. Before you start programming, you must find the subcode or code of the subset to be controlled (television or video recorder). Refer to the list supplied with this user manual (see page subcodes or codes). EN 2 1. Turn on the COMBO you want to control. 2. Hold down the SETUP (11) key until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). 3. Press the TV (2) key, then follow one of the programming methods (A, B, C or D) described earlier. 4. If second code programming is required then repeat steps 2 and 3 above. 6 - Controlling volume in satellite and cable mode For satellite systems with a volume control, you can choose the product that the MUTE (15) and VOL (4) keys will control: the television volume or the volume of the satellite or cable receiver. To choose, proceed as follows: 1. Press the TV (2) key (the remote control must be in TV mode for this procedure). 2. Hold down the SETUP (11) key until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). 3. Release the SETUP (11) key. 4. Press the MUTE (15) key for around 8 seconds. The indicator light will blink and then go off for about 8 seconds before blinking once more and then staying off. 5. If the remote previously controlled the television volume in SAT mode, it will now control the volume of the satellite receiver; if it previously controlled the volume of the satellite receiver, it will now control the television volume. 4 - How to retrieve a programmed code You may want to retrieve the code programmed in the remote control. 1. Hold down the SETUP (11) key until the red indicator lamp (1) remains lit (the indicator light remains on for a few seconds to give you the time to proceed with the following steps. The indicator lamp flashes when this time is almost up, and then goes off). 2. Press the product key (2) that corresponds to the type of product you want to control: TV: television set, DVD: DVD player, SAT: satellite receiver. 3. Press SETUP (11) again briefly. The red indicator lamp flashes once. 4. Press the number keys (0 to 9) in ascending order until the red indicator lamp (1) flashes once. 5. The digit which made the red indicator lamp (1) flash, is the first number of the 3-digit code. Please make note of it. 6. Repeat step 4 to find out the two other numbers of the code. 7. When the third number is found, the red indicator lamp (1) goes off. ...