HF/VHF/UHF ALL MODE TRANSCEIVER The technical propert DSP found in our lead now offers its superio HF, 50MHz 144MHz a First in its class, IF DSP model IF DSP -- First in its class Digital IF filter, manual notch filter, digital twin PBT and more. The latest digital features are incorporated in this compact radio from two DSP chips that deliver superior processing performance. Of course, those features work on all ham bands, from HF to the 70cm band. Digital noise reduction Noise reduction reduces background noise and improves signal-to-noise ratio. The noise reduction level is adjustable in 16 steps. It improves the readability of voice and data signals. Digital noise blanker The noise blanker reduces pulse-type noise such as engine ignition and sparking. The NB level and width (blanking duration) are adjustable in 100 steps. AGC loop performance controlled by DSP You will never experience AGC pumping from a signal filtered out by the DSP system. The digital IF filter and manual notch filter are inside the AGC loop, so you will not encounter AGC blocking. The AGC time constants are flexibly adjustable from slow, middle, fast (or AGC-off) for each operating mode. AGC time constant setting Digital IF filters All the filters you want at your fingertips! You will never have to purchase "Optional" filters as the IC-7000 has adjustable digital filters. You just dial in the width you want and select whether you want a sharp or soft filter shape for SSB and CW modes. Then to pull-in the the weak ones, with a quick turn of the concentric twin PBT knobs, you can either narrow the IF passband, or shift the entire passband to eliminate the QRM. Passband width range 50­500Hz; 50Hz step 600Hz­3.6kHz; 100Hz step 50­500Hz; 50Hz step CW 600Hz­3.6kHz; 100Hz step 50­500Hz; 50Hz step RTTY 600Hz­2.7kHz; 100Hz step AM 200Hz­10kHz; 200Hz step FM 7/10/15kHz; fixed step WFM 280kHz; fixed SSB Mode IF filter setting 2-point MNF (Manual notch filter) Pull out the weak signals in crowded band conditions with Icom's NEW two-point MNF (manual notch filter). Apply 70 dB of rejection to two signals at once! Notch width is adjustable ­ wide, medium, and narrow ­ and an auto-tuning notch filter is available, too. HF/VHF/UHF ALL MODE TRANSCEIVER Manual notch filter Basic performance exceeds your expectations 35W output in 70cm band High power MOS-FET amps supply 35W output power on 430/440MHz band as well as 100W on HF/50MHz bands and 50W on 144MHz. It provides stable, high quality output with low IMD and low spurious emissions even during high duty cycle and extended operation. MOS FET PA units DDS (Direct digital synthesizer) circuit Icom's original DDS (Direct digital synthesizer) circuit improves the C/N ratio, providing a clear, clean transmit signal in all bands. Icom original DDS circuit High stability crystal unit The IC-7000 incorporates a high-stability master oscillator, providing 0.5ppm (­0°C to +50°C). A must for data mode operation. Compact, all in one package The IC-7000 sheds 20mm (25/32 in) of depth compared with the IC-706MKIIG. It's compact body is easy for carrying outdoors or mobile operation. ies and advantages of IF ing base station models r advantages on mobile nd 430/440 MHz bands. Practical functions and operations User-friendly key allocation Eight of the most-used radio functions such as NB, NR, MNF, and ANF are controlled by dedicated function keys grouped around the display for easy visibility. One quick touch turns the function on and off. A longer touch activates adjustment of the function's setting. 2.5 inch color TFT display The 2.5 inch color TFT display presents numbers and indicators in bright, concentrated colors for easy recognition. You can choose from 3 background colors and 2 font styles to suit your preference, in addition to a large operating frequency readout. Negative type Color type Positive type Built-in TV tuner and video output jack Not only does the display provide radio status, but you can watch analog VHF-TV*1 channels! The video output jack allows you to view a magnified display on a TV or external monitor*2. *1 NTSC or PAL. Not available in all versions. *2 3.5(d) mm monaural cable is required. 2-mode band scope The band scope function lets you watch conditions around the band and visually assists in finding other stations. In center mode the band scope range is centered on the receiving frequency (±10kHz to ±250kHz). In Fixed mode the band scope sweeps a fixed range. Fixed mode band scope Multi function meter and SWR graphic display The IC-7000 displays power level, SWR, ALC and compression level of the speech compressor. The SWR graphic display is useful for tuning antennas. The measuring step is selectable from 10/50/100/500kHz steps and the number of measuring steps is adjustable from 3 to 13 steps. Digital voice recorder (DVR) Record your callsign, CQ, or other information in 4 transmit playback memories with alphanumeric labels. A total of 90 seconds is available for the four memories. A front panel REC control allows you to record incoming signals for up to 25 minutes (99 channels)*. The DVR makes portable contesting or mini-expeditions a breeze! * Up to 120 seconds per channel Multimeter screen Other outstanding features · Front panel separation with optional 3.5m/5m separation cable · Selectable main dial tension from heavy, light and click · RF speech compressor controlled by the DSP · CW full break-in · CW receive reverse · CW pitch adjustable · Tone squelch in FM mode · 503 memory channels · Built-in voice synthesizer announces operating frequency, mode and signal strength · Duplex mode and automatic repeater function · Transmit monitor · DTMF monitor · 1Hz tuning · VOX · CI-V interface · RIT/TX · RF/SQL knob · Large speaker · Auto TS function · Thermo control silent cooling fan · Noise squelch and S-meter squelch · Preamplifier · Dial lock · 20dB attenuator · Adjustable SSB transmit bandwidth Voice RX memory Built-in RTTY demodulator The RTTY demodulator and decoder are built-in. External units and PC are no longer required for decoding. The twin peak audio filter reduces interfering signals overlapping the tones and the tuning indicator helps you zero-in with accurate tuning. RTTY decode screen Remote control microphone, HM-151 The HM-151 has a 10-keypad for quick channel selection. The triple band stacking register memorizes the last three frequencies and modes used on each band. Push the band button once to three times to recall the channel setting. The F-1 and F-2 buttons are programmable as shortcut menus of your often used functions. Key illumination HF/VHF/UHF ALL MODE TRANSCEIVER SPECIFICATIONS GENERAL TRANSMITTER · Modulation system SSB AM FM · Output power SSB/CW/RTTY/FM AM · Spurious emissions : Balanced modulation Low level modulation Variable reactance modulation : HF/50MHz 2­100W 1­40W 144MHz 2­50W 2­20W 440MHz 2­35W 2­14W · Frequency coverage (unit: MHz)*1 : Receive Transmit 0.030­199.999*2 400.000­470.000*2 1.800­ 1.999 3.500­ 3.999 5.3305, 5.3465, 5.3665, 5.3715, 5.4035*3 7.000­ 7.300 10.100­ 10.150 14.000­ 14.350 18.068­ 18.168 21.000­ 21.450 24.890­ 24.990 28.000­ 29.700 50.000­ 54.000 144.000­148.000 430.000­450.000 *1 Showing USA version, frequency coverage depends on version. *2 Some frequency ranges are not guaranteed. *3 USB mode only. · Mode : USB, LSB, CW, RTTY, AM, FM, WFM (Rx only) · Number of memory Ch. : 503 (495 regular, 6 scan edges and 2 call) · Antenna connector : SO-239×2 (for HF/50MHz and 144/ 430/440MHz bands; 50) : Less than ­50dB (HF bands) Less than ­60dB (other bands) · Carrier suppression : More than 50dB · Unwanted sideband suppression: More than 50dB · Microphone connector : 8-pin modular jack (600) RECEIVER · Squelch sensitivity (Pre-amp: ON, threshold): SSB Less than 5.6µV FM Less than 0.3µV · Selectivity (representative value): SSB More than 2.4kHz/­6dB (BW: 2.4kHz, sharp) Less than 3.6kHz/­60dB CW More than 500Hz/­6dB (BW: 500Hz, sharp) Less than 900Hz/­60dB RTTY (BW: 350Hz) More than 360Hz/­6dB Less than 650Hz/­60dB AM (BW: 6kHz) More than 6.0kHz/­6dB Less than 15.0kHz/­60dB FM (BW: 15kHz) More than 12.0kHz/­6dB Less than 20.0kHz/­60dB · Spurious and image : More than 70dB (HF bands) rejection ratio More than 65dB (Other bands) (except 1/2 IF through on 50MHz, IF through on 144MHz) · Temperature range · Frequency stability : ­10°C to +60°C; +14°F to +140°F : Less than ±0.5ppm (0°C to +50°C; +32°F to +122°F) · AF output power (at 13.8V DC) · Power supply requirement : 13.8V DC ±15% · Power consumption : Tx Max. power 22.0A (approx.) Rx Standby 1.3A Max. audio 1.6A · Dimensions : 167(W)×58(H)×180(D) mm; (Projections not included) 69/16(W)×29/32(H)×73/32(D) in : 2.3kg; 5.1lb · Weight (approx.) · Intermediate frequencies : SSB, CW, RTTY, AM, FM 124.487MHz, 455kHz, 16.15kHz WFM 134.732MHz, 10.70MHz · Sensitivity (Pre-amp: ON) : SSB/CW AM FM WFM 0.5­1.8MHz 1.8­29.9MHz 50­54MHz 144/440MHz ­ 0.15µV 0.12µV 0.11µV 13µV 2.0µV 1.0µV 1.0µV ­ 0.5µV (28­29.7) 0.25µV 0.18µV ­ ­ 10.0µV (76­108MHz) · EXT SP connector : More than 2.0W at 10% distortion with an 8 load : 2-conductor 3.5 (d) mm (1/8)/8 All stated specifications are subject to change without notice or obligation. SSB/CW, AM : 10dB S/N, FM, WFM : 12dB SINAD Supplied accessories: · Hand microphone, HM-151 · DC power cable · Spare fuses · ACC cable (13-pin) · Electronic keyer plug · RTTY key plug OPTIONS IC-PW1/IC-PW1EURO HF+50MHz 1kW HF LINEAR AMPLIFIER Covers all HF and 50MHz bands, provides clean, stable 1kW output. Automatic antenna tuner and compact detachable controller are standard. 2 exciter inputs are available. (An optional OPC-599 is required.) · AH-2b ANTENNA ELEMENT For mobile operation with the AH-4. All bands between 7­54MHz can be matched. · AH-4 HF+50MHz AUTOMATIC ANTENNA TUNER Covers 3.5­54MHz with a 7m (23ft) or longer wire antenna. · AT-180 HF+50MHz AUTOMATIC ANTENNA TUNER Style and size are matched to the IC-7000. · SM-20 DESKTOP MICROPHONE High quality desktop microphone. (An optional OPC-589 is required.) · HM-151 REMOTECONTROL MICROPHONE Same as supplied. · CT-17 CI-V LEVEL CONVERTER For remote transceiver control using a PC with an RS-232C. · SP-10 EXTERNAL SPEAKER Heavy duty speaker for mobile use. · MB-62 MOBILE MOUNTING BRACKET For mounting the IC-7000 main unit or the AT-180. · MB-65 MOUNTING BASE For mounting the detached front panel in a vehicle. The MB-105 is required. · MB-105 MOBILE MOUNTING BRACKET For mounting the detached front panel. · MB-106 CARRYING HANDLE Convenient when carrying the transceiver. · OPC-1443/OPC-1444 SEPARATION CABLES OPC-1443: 3.5m (11ft) OPC-1444: 5m (16ft) · OPC-589 MODULAR 8-PIN CABLE ADAPTER For using a regular 8-pin desktop microphone with IC-7000. · OPC-598 ACC 13 PIN LONG CABLE FOR AT-180 (7m; 23ft) · OPC-599 CABLE ADAPTER Converts 13-pin ACC connector to 7-pin + 8-pin ACC connector for connection with IC-PW1/EURO. · OPC-742 ACC 13 PIN CABLE ADAPTER Required when using both AT-180 and a 2 m or 70 cm linear amplifier. READ ALL INSTRUCTIONS carefully and completely before using the transceiver. 1-1-32, Kamiminami, Hirano-ku, Osaka 547-0003, Japan Phone: +81 (06) 6793 5302 Fax: +81 (06) 6793 0013 URL: http://www.icom.co.jp/world/index.html Count on us! 2380 116th Avenue NE, Bellevue, WA 98004, U.S.A. Phone : +1 (425) 454-8155 Fax : +1 (425) 454-1509 E-mail : sales@icomamerica.com URL : http://www.icomamerica.com 146A Harris Road, East Tamaki, Auckland, New Zealand Phone : +64 (09) 274 4062 Fax : +64 (09) 274 4708 E-mail : inquiries@icom.co.nz URL : http://www.icom.co.nz Unit 9, Sea St., Herne Bay, Kent, CT6 8LD, U.K. Phone : +44 (01227) 741741 Fax : +44 (01227) 741742 E-mail : info@icomuk.co.uk URL : http://www.icomuk.co.uk 6F No. 68, Sec. 1 Cheng-Teh Road, Taipei, Taiwan, R.O.C. Phone : +886 (02) 2559 1899 Fax : +886 (02) 2559 1874 E-mail : sales@asia-icom.com URL : http://www.asia-icom.com Your local distributor/dealer: Glenwood Centre #150-6165 Highway 17, Delta, B.C., V4K 5B8, Canada Phone : +1 (604) 952-4266 Fax : +1 (604) 952-0090 E-mail : info@icomcanada.com URL : http://www.icomcanada.com Communication Equipment Himmelgeister Str. 100, D-40225 Düsseldorf, Germany Phone : +49 (0211) 346047 Fax : +49 (0211) 333639 E-mail : info@icomeurope.com URL : http://www.icomeurope.com Zac de la Plaine, 1, Rue Brindejonc des Moulinais BP 5804, 31505 Toulouse Cedex, France Phone : +33 (5) 61 36 03 03 Fax : +33 (5) 61 36 03 00 E-mail : icom@icom-france.com URL : http://www.icom-france.com 10C07, Long Silver Mansion, No.88, Yong Ding Road, Haidian District, Beijing, 100039, China Phone : +86 (010) 5889 5391/5392/5393 Fax : +86 (010) 5889 5395 E-mail : bjicom@bjicom.com URL : http://www.bjicom.com A.B.N. 88 006 092 575 Unit 1 / 103 Garden Roa ...