Portable/Base Station All-Mode 1.8-430 MHz Transceiver Turn your next weekend getaway into an HF DX-pedition, and leave the power supply at home! Portable/Base Station All-Mode 1.8-430 MHz Transceiver Shown with optional FC-30 Automatic Antenna Tuner and FP-30 AC Power Supply. FT-897: THE WORLD'S FIRST HF/VHF/UHF MULTIMODE PORTABLE/BASE STATION! Now you can own a fully self-contained, high-power HF/VHF/UHF multimode transceiver that can be operated without an external power supply! With the exciting new FT-897, you can operate fully portable at the 20-Watt power level, using the optional FNB-78 13.2V/4500 mAh Ni-MH Battery Pack (two may be installed simultaneously). Use an external 13.8 Volt power supply for 100 Watts of power on HF/50 MHz, 50 Watts on 144 MHz, and 20 Watts on 430 MHz. Or install the optional FP-30 Internal Power Supply in place of the internal batteries. . .however you configure the FT-897, there will be no limit to the DX action you'll enjoy! FIELD STATION FT-897+FNB-78(optional) For an afternoon at the park, a day at the beach, or an emergency exercise, power your FT-897 using the optional FNB-78 Ni-MH Battery Pack, and you're on the air-completely portable! MOBILE STATION FT-897+ATAS-120(optional) Mobile operation, using the FT-897 as the cornerstone, is pure joy! The combination of the FT-897 and the ATAS-120 Active-Tuning Antenna System provides automated operation from HF through the UHF spectrum! FT-897+FP-30+FC-30(optional) The FT-897's outstanding fundamental performance invites expansion into a full-featured base station. The optional FP-30 Internal Power Supply provides operation from AC sources, and the clamp-on FC-30 Automatic Antenna Tuner option expands the impedance range of the transceiver. Round out your station with the optional MD-200A8X Deluxe Desk Microphone and the optional VL-1000 Quadra System Linear Amplifier for world-class performance at home! BASE STATION Battery-powered Field Operation The bottom side of the FT-897 contains a "power source tray" which can accommodate up to two of the optional 13.2 Volt, 4500 mAh FNB-78 Ni-MH Battery Packs, for completely portable operation without any external power source. Maximum power output is 20 Watts (70 cm: 10 W) during battery operation, and with two FNB-78s you may expect up to eight hours of operating time (TX 5%, RX 5%, standby 90%). What's more, you can charge one of the FNB-78 Battery Packs while operating the FT-897 off the other pack--ideal for situations where solar or other power sources are available. The CD-24 Charge Adapter provides the necessary voltage for charging, and it may be used in conjunction with an external 13.8 Volt source, or the PA-26 AC Adapter may be used to power the CD-24. DC 13.8 V Mobile Operation Using an external 13.8 Volt power source, you get a full 100 Watts of power output on HF and six meters (144 MHz: 50 W, 430 MHz: 20 Top-quality Base Station The power source tray of the FT-897 is designed to accommodate the optional FP-30 Internal Power Supply, allowing fullpower operation from 100-120 V or 200-240 V AC power sources. The quiet switching-regulator design of the FP-30 is tolerant of AC input voltage variations, making it ideal for DX-pedition use! And to extend the impedance bandwidth of your antenna system, the innovative FC-30 Automatic Antenna Tuner option clamps onto the left side of the FP-30 (optional) Internal Switching Power Supply Limited-space Antenna Ideas If you're living in an apartment, townhouse, or other location where you don't have a lot of space to install an antenna, ask your dealer for a suitable balcony mount for the ATAS-120! When using the ATAS-120 with the optional ATBK-100 Antenna Base Kit (VHF/UHF Counterpoise), you'll be able to get on the air with an efficient, automatically-tuned antenna system that will put DX contacts into your log. ATBK100 Antenna Base Kit (VHF/UHF Counterpoise) A B ATAS-120 Active-Tuning Antenna System Internal Ni-MH Battery Pack FNB-78 (optional) FT-897 System Diagram Active-Tuning Antenna ATAS-25 (144/430MHz) ATAS-120 144/430MHz ANT Yagi, Dip. etc. (HF/50MHz) Active-Tuning Antenna System: The ATAS Series! (optional) Yaesu's patented ATAS-120 Active-Tuning Antenna System provides a compact yet efficient, automatically-adjusting antenna for mobile, portable, or apartment-balcony use! Utilizing DC voltages fed from the FT-897 the ATAS-120 automatically adjusts its length longer or shorter, with the FT-897 feeding a tiny amount of power for SWR detection by its internal directional coupler. When the best impedance match is found, tuning automatically stops, and operation can begin. Specified for operation on the 7/14/21/28 MHz Amateur bands, the ATAS-120 contracts fully for use on the 50/144/430 MHz bands, providing a low SWR for local FM work (where vertical polarization is predominant). And if you're an apartment dweller, use the optional ATBK-100 Antenna Base Kit, which provides an excellent counterpoise to Antenna Base Kit ensure low-angle ATBK-100 radiation on the VHF/UHF bands. Active-Tuning Antenna System Active-Tuning Antenna System DUP DUP HF/50MHz DUP Duplexer *FC-30 Bolt-on Automatic Antenna Tuner *FC-30 ATAS-120 (Automatic type) ATAS-25 (Manual type) Internal Battery *FNB-78 Portable Ni-MH Battery Pack Base Power Supply Mobile DC12V Ni-MH Battery Pack *FNB-78 *FNB-78 *FP-30 AC100V/200V Charge Adapter Charge Adapter *CD-24 Charger for CD-24 Internal Power Supply *FP-30 *CD-24 *PA-26 DC-12V AC100~240 V *optional See your Yaesu dealer for details regarding suitable mounts for the ATAS-120. Compact, All-In-One Transportable HF/VHF/UHF Communications Station Measuring just 7.9" x 3.2" x 9.1" (without knobs), the FT-897 is unmatched in performance versus size. With the optional FC-30 Automatic Antenna Tuner installed, the convenient carrying handle of the FT-897 lets you easily transport your HF/VHF/UHF station to a portable location and get on the air instantly. Actual Size FT-897 PORTABLE BASE STATION Whether at home, in the car, or on a DX-pedition, the FT-897 brings you home-station performance in a compact, transportable package. Features like Digital Signal Processing, Collins® Mechanical filter options, and easy Digital mode interfacing give you leading-edge performance, wherever you create your Hamshack! adjustment of a number of transceiver operating functions during operation. Pressing the [F] key allows selection of the operating function row, using the Selector knob, and you may then press the [A], [B], or [C] switch, as needed, to change the setting. What's more, a number of these keys provide instant "hot key" switching to a related Menu item, for "set and forget" configuration adjustment. low noise low noise figure are the product of the advanced preamplifier stage with negative feedback for stability, and the GaAs balanced mixer design, with careful gain distribution from the RF through the audio stages. Flexibility in strong-signal operation is also provided by the RF Gain control, input attenuator, input preamplifier bypass capability (IPO), and Slow/Fast/Off AGC selections. IF SHIFT To roll off interference using the analog IF filters, the IF Shift feature varies the frequency of the IF passband across the filter, removing interference from either the high-frequency or low-frequency side without varying the pitch of the incoming signal. IF NOISE BLANKER Another noise reduction circuit, in addition to the DSP Noise Reduction, is the IF Noise Blanker. Noise pulses are detected early in the receiver, then amplified and used to drive a carefully-timed gate in the receiver IF that blanks out impulsetype noise from automotive ignition systems. will send five-character letters and/or numbers via the speaker, so you can practice CW reception when the bands are dead. Easy Data Mode Interfacing: Configure for 1200/9600 bps Packet, RTTY, or PSK31 in minutes. Transmit Data Level is adjustable via the Menu. Innovative FC-30 (optional) Automatic Antenna Tuner Adding less than 2" to the total width of the FT-897 assembly, the optional FC-30 is a highspeed, relay-controlled Automatic Antenna Tuner utilizing a combination of sixteen capacitors and nine low-loss coils to reduce SWR as presented to the FT-897 feedpoint. Impedances of 17 to 150 Ohms may be tuned by the FC-30 on HF (25 to 100 Ohms on 50 MHz), and the lightning-fast tuning ensures that you won't miss out on the DX. Advanced Convenience Features for VHF/UHF Operation! Both CTCSS and DCS Encoder/Decoders are built in! For easy access to repeaters, a 50-tone CTCSS system works along with a 104-code Digital Code Squelch (DCS) in the FT-897. For applications requiring split CTCSS/DCS access, a convenient "Split Tone" feature is also provided! DSP Microphone Equalizer: Focus the available power to match your voice characteristics. Two Antenna Connectors: Separate jacks for HF/50 MHz and 144/430 MHz. Large, Easy-to-See TX/RX Status LED. Optional HighStability Reference Oscillator: The TCXO-9 provides ±0.5 ppm stability at 77°F/25°C for applications requiring very high frequency accuracy. Versatile Scanning Features: VFO Scan, Memory Scan, Band-Limited Scanning (PMS), and Dual Watch. Smart SearchTM: Automatic "Soft" Memory Channel loading system. ARTSTM: Auto-Range Transponder system tells you if another ARTS-equipped station goes out of communications range. Spectrum Scope: Watch activity ±9 or ±63 channels from your current frequency. VOX: With separate adjustments for voice delay and CW receiver recovery time. Auto Power Off (APO), Time-Out timer (TOT) and Automatic Repeater Shift CAT System: Computer programming capability for DX/contest logging software, etc. Rugged, High-Output Power Amplifier with Efficient Heat Sink Achieving 100 Watts of power output from such a compact package is a difficult mechanical and electrical engineering task. On HF, push-pull 2SK5125 MOSFETs driven by push-pull 2SK2975s provide the 100-Watt power capability, while on VHF maximum efficiency during battery operation is yielded by 2SC3102 bipolar PA transistors. The rugged aluminum die-cast chassis provides a solid foundation for the heat sink for the power amplifier, with a total of almost 40 cubic inches of heat sink surface area available. With its quiet, thermostatically-controlled twin cooling fans, the FT-897 will stand up to the rigors of DX-pedition or home contest use, with dissipation capability to spare. High-Performance PLL Design The quiet, fast-acting local oscillator system of the FT-897 borrows extensively from the renowned FT-847, using a Direct Digital Synthesizer (DDS) to achieve fast lock times and silky-smooth tuning in 10 Hz steps. The excellent carrier-to-noise ratio helps preserve spurious-free dynamic range in a crowded band, and the smooth tuning leaves you with the feeling you're using an analog VFO. Upgrade with Collins® Mechanical Filters for SSB and CW! To enhance performance on both receive and transmit, high-performance Collins® Mechanical Filter options are available for both SSB and CW. For SSB, the 2.3 kHz, 10-pole model YF-122S (optional) provides a very flat passband response, for naturalsounding transmit audio, along with excellent skirt selectivity. And for CW, the 500 Hz, 7-pole YF-122C (option) helps separate signals on a crowded band in a contest. Versatile Memory System! The FT-897 provides up to 200 "Main" memory channels, each of which may be named with an Alpha-Numeric label of up to eight characters. These 200 Memories may be separated in as many as 10 Memory Groups of 20 Memories each. For added convenience, you also get a "Quick Memory" and a "Home Channel" on each band, plus ten pairs of band-limit memories, to let you restrict operation to a sub-band, if you like. (optional) Digital and Analog Interference/Noise Reduction The FT-897 includes a wide array of analog and DSP filters to help you dig out those weak DX signals on a crowded band! One-touch activation of the DSP filters, plus a convenient "DSP" LED on the front panel, enhance the ease of using the DSP. DSP BANDPASS FILTER Separate DSP Bandpass Filters for Voice and CW augment the analog filters, yielding a dramatic improvement in signal-to-noise ratio and interference reduction. For Voice modes, both the low- and high-side cutoff frequencies are independently adjustable, and for CW you may choose bandwidths of 240 Hz, 120 Hz, or a razor-sharp 60 Hz. DSP AUTO-NOTCH FILTER ¥SSB DSP Bandpass Filter To reduce interference caused by annoying carriers within the receiver passband, the DSP Auto-Notch provides a significant reduction in the interference level. If multiple carriers are present, the ¥DSP Auto-Notch Filter DSP will detect and notch all the carriers present. DSP NOISE REDUCTION The very effective DSP Noise Reduction filter of the FT-897 is a tremendous operating aid, greatly reducing background ¥DSP Noise Reduction Filter noise without introducing annoyi ...