User manual YAESU FT-2000 - CAT OPERATION REFERENCE BOOK

CAT (COMPUTER AIDED TRANSCEIVER) OPERATION FT-2000 SERIES CAT OPERATION REFERENCE BOOK FT-2000 SERIES CAT OPERATION REFERENCE BOOK CAT (COMPUTER AIDED TRANSCEIVER) OPERATION OVERVIEW The CAT (Computer Aided Transceiver) System in the FT-2000 series provides control of frequency, VFO, memory, and other settings such as dual-channel memories and diversity reception using an external personal computer. This allows multiple control operations to be fully automated as single mouse clicks or keystroke operations on the computer keyboard. The FT-2000 series has a built-in level converter, allowing direct connection from the rear-panel CAT jack to the serial port of your computer without the need of any external boxes. You will need a serial cable for connection to the RS-232C (serial or COM port) connector on your computer. Purchase a standard serial cable (not the socalled "null modem" type), ensuring it has the correct gender and number of pins (some serial COM port connectors use a 9-pin rather than 25-pin configuration). If your computer uses a custom connector, you may have to construct the cable. In this case, refer to the technical documentation supplied with your computer for correct data connection. Vertex Standard does not produce CAT System operating software due to the wide variety of personal computers and operating systems in use today. However, the information provided in this chapter explains the serial data structure and opcodes used by the CAT system. This information, along with the short programming examples, is intended to help you start writing programs on your own. As you become more familiar with CAT operation, you can customize programs later on for your operating needs and discover the true operating potential of this system. CAT JACK PIN NO. PIN NAME N/A SERIAL OUT SERIAL IN N/A GND N/A RTS I/O --Output Input ------Input CTS Output N/A --- FUNCTION --Outputs the Serial Data from the transceiver to the computer. Inputs the Serial Data from the computer to the transceiver. --Signal Ground --When the computer is not ready to receive data, this port goes to "L" for inhibit the transmit data from the transceiver. When the transceiver is not ready to receive data, this port goes to "L" for inhibit the transmit data from the computer. --- COM CAT RS-232C "Straight" Cable Page 1 FT-2000 SERIES CAT OPERATION REFERENCE BOOK CAT (COMPUTER AIDED TRANSCEIVER) OPERATION CONTROL COMMAND A computer control command is composed of an alphabetical command, various parameters, and the terminator that signals the end of the control command. Example: Set the main band (VFO-A) frequency to 14.250000 MHz. FA Command 14250000 Parameter ; Terminator Parameters Parameters are used to specify information necessary to implement the desired command. The parameters to be used for each command are predetermined. The number of digits assigned to each parameter is also predetermined. Refer to the "Control Command List" and the "Control Command Tables" to configure the appropriate parameters. When configuring parameters, be careful not to make the following mistakes. For example, when correct parameter is "IS0+1000" (IF SHIFT): IS01000; Not enough parameters specified (No direction (+) given for the IF shift) IS0+100; Not enough digits (Only three frequency digits given) IS0_+_1000; Unnecessary characters between parameters IS0+10000; Too many digits (Five frequency digits given) Note: If a particular parameter is not applicable to the FT2000, the parameter digits should be filled using any character except the ASCII control codes (00 to 1Fh) and the terminator (;). There is three for the FT-2000 Command as shown below: Set command: Set a particular condition (to the FT-2000) Read command: Reads an answer (from the FT-2000) Answer command: Transmits a condition (from the FT-2000) For example, note the following in the case of the FA command (Set the main band (VFO-A) frequency): To set the main band (VFO-A) frequency to 14.250000 MHz, the following command is sent from the computer to the transceiver: "FA14250000;" (Set command) To read the main band (VFO-A) frequency, the following command is sent from the computer to the transceiver: "FA;" (Read command) When the Read command above has been sent, the following command is returned to the computer: "FA14250000;" (Answer command) Terminator To signal the end of a command, it is necessary to use a semicolon (;). The digit where this special character must appear differs depending on the command used. Alphabetical Commands A command consists of 2 alphabetical characters. You may use either lower or upper case characters. The commands available for this transceiver are listed in the "PC Control Command Tables" on the following pages. FT-2000 SERIES CAT OPERATION REFERENCE BOOK Page 2 CAT (COMPUTER AIDED TRANSCEIVER) OPERATION CONTROL COMMAND LIST COMMAND AB AC AG AI AM AN BC BD BI BP BS BU BY CH CN CO CS CT DA DN DP DS ED EK EU EX FA FB FK FR FS FT GT ID IF IS KM KP KR KS KY LK LM MA MC MD MG MK ML FUNCTION VFO-A TO VFO-B ANTENNA TUNER CONTROL AF GAIN AUTO INFORMATION VFO-A TO MEMORY CHANNEL ANTENNA NUMBER AUTO NOTCH BAND DOWN BREAK-IN MANUAL NOTCH BAND SELECT BAND UP BUSY CHANNEL UP/DOWN CTCSS NUMBER CONTOUR CW SPOT CTCSS DIMMER DOWN DISPLAY DIMMER SWITCH ENCORDER DOWN ENT KEY ENCORDER UP MENU FREQUENCY VFO-A FREQUENCY VFO-B FUNCTION KEY FUNCTION RX FAST STEP FUNCTION TX AGC FUNCTION IDENTIFICATION INFORMATION IF-SHIFT KEYER MEMORY KEY PITCH KEYER KEY SPEED CW KEYING LOCK LOAD MESSEGE MEMORY CHANNEL TO VFO-A MEMORY CHANNEL MODE MIC GAIN MODE KEY MONITOR LEVEL SET READ ANS. O O O O O O O O O O O O X O O O O O O O O O O O O O O O O O O O O X X O O O O O O O O O O O O O O X O O O X O O X O O X X O X O O O O O X O O X X X O O O X O O O O O O O O O O O X O O X O O O X O X O O O X O O X O O X X O X O O O O O X O O X X X O O O X O O O O O O O O O O O X O O X O O O X O AI X O O X X O O X O O X X O X O O O O X X O O X X X O O O X O O O O X O O X O O O X O X X X O O X O COMMAND MR MS M W MX NA NB NL NR OI OS PA PB PC PL PR PS QI QR QS RA RC RD RF RG RI RL RM RO RS RT RU SC SD SF SH SM SQ SV TS TX UL UP VD VF VG VM VS VX XT FUNCTION MEMORY READ METER SW MEMORY WRITE MOX SET NARROW NOISE BLANKER NOISE BLANKER LEVEL NOISE REDUCTION OPPOSITE BAND INFORMATION OFFSET (REPEATER SHIFT) PRE-AMP (IPO) PLAY BACK POWER CONTROL SPEECH PROCESSOR LEVEL SPEECH PROCESSOR POWER SWITH QMB STORE QMB RECALL QUICK SPLIT RF ATTENUATOR CLAR CLEAR CLAR DOWN ROOFING FILTER RF GAIN RADIO INFORMATION NOISE REDUCTION LEVEL READ METER ROTATOR RADIO STATUS CLAR CLAR UP SCAN SEMI BREAK-IN DELAY TIME SUB-DIAL FUNCTION WIDTH S METER SQUELCH LEVEL SWAP VFO TXW TX SET UNLOCK UP VOX DELAY TIME VRF FILTER VOX GAIN [V/M] KEY FUNCTION VFO SELECT VOX TX CLAR SET READ ANS. X O O O O O O O X O O O O O O O O O O O O O O O X O X O X O O O O O O X O O O O X O O O O O O O O O O X O O O O O O O O O O O O O X X X O X X O O O O O O O O X O O O O O O X O O O X O O O X O O O O O X O O O O O O O O O O O O O X X X O X X O O O O O O O O X O O O O O O X O O O X O O O X O O O AI X O X O O O O O X O O X O O O X X X X O X X O O O O O X O O X O O O O O O X O O O X O O O X O O O Page 3 FT-2000 SERIES CAT OPERATION REFERENCE BOOK CAT (COMPUTER AIDED TRANSCEIVER) OPERATION CONTROL COMMAND TABLES AB Set Read Answer AC Set Read Answer AG Set Read Answer AI Set Read Answer AM Set Read Answer AN Set Read Answer BC Set Read Answer BD Set Read Answer BI Set Read Answer VFO-A TO VFO-B 1 2 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10 A 1 1 B 2 2 ; 3 3 ANTENNA TUNER CONTROL 1 2 3 3 4 4 4 5 5 5 6 7 7 7 8 8 8 9 9 9 10 10 10 A 1 C 2 P1 P2 P3 ; 3 ; 6 6 P1 0: Fixed P2 0: Fixed P3 0: Tuner "OFF" 1: Tuner "ON" 2: Tuning Start A 1 C 2 A 1 C 2 P1 P2 P3 3 3 4 4 5 5 5 ; 6 6 6 7 8 8 8 9 9 9 10 10 10 AF GAIN A 1 G 2 P1 P2 P2 P2 P1 3 ; 7 7 P1 0: Main (VFO-A) Band Receiver 1: Sub (VFO-B) Band Receiver P2 000 - 255 A 1 G 2 ; 4 A 1 G 2 P1 P2 P2 P2 3 4 5 5 5 6 6 6 ; 7 7 7 8 8 8 9 9 9 10 10 10 AUTO INFORMATION A 1 I 2 P1 3 ; 4 4 P1 0: Auto Information "OFF" 1: Auto Information "ON" This parameter is set to "0" (OFF) automatically when the transceiver is turned "OFF." A 1 I 2 ; 3 A 1 I 2 P1 3 ; 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10 VFO-A TO MEMORY CHANNEL A 1 1 M 2 2 ; 3 3 ANTENNA NUMBER 1 2 3 3 4 4 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10 A 1 N 2 P1 P2 P1 3 ; 5 5 A 1 N 2 ; 4 P1 0: Fixed P2 1: ANT "1" 2: ANT "2" 5: ANT "RX" P3 1: ANT "1" 2: ANT "2" P4 0: ANT "RX" "OFF" 1: ANT "RX" "ON" A 1 N 2 P1 P3 P4 3 3 4 4 5 ; 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10 AUTO NOTCH B 1 C 2 P1 P2 P1 3 ; 5 5 P1 0:Fixed P2 0: Auto Notch "OFF" 1: Auto Notch "ON" B 1 C 2 ; 4 B 1 C 2 P1 P2 3 4 ; 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10 BAND DOWN B 1 1 D 2 2 P1 3 3 ; 4 4 P1 0: Main (VFO-A) Band 1: Sub (VFO-B) Band BREAK-IN 1 2 3 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10 B 1 I 2 P1 3 ; 4 4 P1 0: Break-in "OFF" 1: Break-in "ON" B 1 I 2 ; 3 B I P1 ; FT-2000 SERIES CAT OPERATION REFERENCE BOOK Page 4 CAT (COMPUTER AIDED TRANSCEIVER) OPERATION CONTROL COMMAND TABLES BP Set Read Answer BS Set Read Answer BU Set Read Answer BY Set Read Answer CH Set Read Answer CN Set Read Answer CO Set Read Answer CS Set Read Answer MANUAL NOTCH 1 2 3 3 3 4 4 4 5 5 6 6 6 7 7 7 8 9 9 9 10 10 10 B 1 P 2 P1 P2 P3 P3 P3 P1 P2 ; 5 ; 8 8 P1 0:Fixed P2 0: Manual NOTCH "ON/OFF" 1: Manual NOTCH LEVEL B 1 P 2 P3 When P2=0 000: OFF 001: ON When P2=1 001 - 400 (NOTCH Frequency : x 10 Hz ) B 1 P 2 P1 P2 P3 P3 P3 3 3 3 4 4 4 5 6 6 6 7 7 7 ; 8 8 8 9 9 9 10 10 10 BAND SELECT B 1 1 S 2 2 P1 P1 ; 5 5 P1 00: 1.8 MHz 01: 3.5 MHz 02: 5 MHz 03: 7 MHz 04: 10 MHz 05: 14 MHz 06: 18 MHz 07: 21 MHz 08: 24.5 MHz 09: 28 MHz 10: 50 MHz 11: GEN BAND UP 1 2 3 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10 B 1 1 U 2 2 P1 3 3 ; 4 4 P1 0: Main (VFO-A) Band 1: Sub (VFO-B) Band BUSY 1 1 2 2 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10 B 1 Y 2 ; 3 P1 0: Main (VFO-A) Band BUSY "OFF" 1: Main (VFO-A) Band BUSY "ON" P2 0: Sub (VFO-B) Band BUSY "OFF" 1: Sub (VFO-B) Band BUSY "ON" B 1 Y 2 P1 P2 3 4 ; 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10 CHANNEL UP/DOWN C 1 1 H 2 2 P1 3 3 ; 4 4 P1 0: Memory Channel "UP" 1: Memory Channel "DOWN" CTCSS TONE FREQUENCY 1 2 3 3 4 4 5 5 5 6 7 7 7 8 8 8 9 9 9 10 10 10 C 1 N 2 P1 P2 P2 P1 3 ; 6 6 P1 0: Main (VFO-A) Band Receiver 1: Sub (VFO-B) Band Receiver P2 0 - 49: Tone Frequency Number (See Table Below) C 1 N 2 ; 4 C 1 N 2 P1 P2 P2 3 3 3 4 4 4 5 5 ; 6 6 6 7 8 8 8 9 9 9 10 10 10 CONTOUR C 1 O 2 P1 P2 P3 P3 P1 P2 ; 5 ; 7 7 P1 0:Fixed P2 0: CONTOUR/APF "ON/OFF" 1: CONTOUR FREQUENCY C 1 O 2 P3 When P2=0, 000: CONTOUR/APF "OFF" 001: CONTOUR "ON" 002: APF "ON" When P2=1, 01 - 40 (CONTOUR FREQUENCY) C 1 O 2 P1 P2 P3 P3 3 4 5 5 5 6 6 6 ; 7 7 7 8 8 8 9 9 9 10 10 10 CW SPOT C 1 S 2 P1 3 ; 4 4 P1 0: OFF 1: ON C 1 S 2 ; 3 C S P1 ; CTCSS TONE CHART 00 01 02 03 04 05 06 07 08 67.0 Hz 69.3 Hz 71.9 Hz 74.4 Hz 77.0 Hz 79.7 Hz 82.5 Hz 85.4 Hz 88.5 Hz 09 10 11 12 13 14 15 16 17 91.5 Hz 94.8 Hz 97.4 Hz 100.0 Hz 103.5 Hz 107.2 Hz 110.9 Hz 114.8 Hz 118.8 Hz 18 19 20 21 22 23 24 25 26 123.0 Hz 127.3 Hz 131.8 Hz 136.5 Hz 141.3 Hz 146.2 Hz 151.4 Hz 156.7 Hz 159.8 Hz 27 28 29 30 31 32 33 34 35 162.2 Hz 165.5 Hz 167.9 Hz 171.3 Hz 173.8 Hz 177.3 Hz 179.9 Hz 183.5 Hz 186.2 Hz 36 37 38 39 40 41 42 43 44 189.9 Hz 192.8 Hz 196.6 Hz 199.5 Hz 203.5 Hz 206.5 Hz 210.7 Hz 218.1 Hz 225.7 Hz 45 46 47 48 49 --------229.1 Hz 233.6 Hz 241.8 Hz 250.3 Hz 254.1 Hz --------- Page 5 FT-2000 SERIES CAT OPERATION REFERENCE BOOK CAT (COMPUTER AIDED TRANSCEIVER) OPERATION CONTROL COMMAND TABLES CT Set Read Answer DA Set Read Answer DN Set Read Answer DP Set Read Answer DS Set Read Answer ED Set Read Answer EK Set Read Answer EU Set Read Answer EX Set Read Answer CTCSS 1 2 3 3 4 4 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10 C 1 T 2 P1 P2 P1 3 ; 5 5 C 1 T 2 ; 4 P1 0: Main (VFO-A) Band Receiver 1: Sub (VFO-B) Band Receiver P2 0: CTCSS "OFF" 1: CTCSS ENC/DEC "ON" 2: CTCSS ENC "ON" C 1 T 2 P1 P2 3 3 4 4 4 ; 5 5 5 6 6 6 7 8 8 8 9 9 9 10 10 10 DIMMER D 1 A 2 P1 P1 P2 P2 ; 3 ; 7 7 P1 00 - 07: VFD Backlight Brightness Level P2 00 - 15: Meter (except VFD) Brightness Level D 1 A 2 D 1 A 2 P1 P1 P2 P2 3 4 4 4 5 5 5 6 6 6 ; 7 7 7 8 8 8 9 9 9 10 10 10 MIC DWN D 1 1 N 2 2 ; 3 3 DISPLAY 1 2 3 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10 D 1 P 2 P1 3 ; 4 4 D 1 P 2 ; 3 D 1 P 2 P1 3 ; 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10 P1 0: World Clock Display 1: Band Scope Display 2: AF Oscilloscope/Spectrum Analyzer Display 3: Log Book Display 4: Temperature/SWR Display 5: Rotator Display 6: Memory Channel List Display : This command does not activates when the optional Data Managemnt Unit is not attached. DIMMER SWITCH D 1 S 2 P1 3 ; 4 4 P1 0: DIMMER "OFF" 1: DIMMER "ON" D 1 S 2 ; 3 D 1 S 2 P1 3 3 3 ; 4 4 4 5 5 5 6 7 7 7 8 8 8 9 9 9 10 10 10 ENCORDER DOWN E 1 1 D 2 2 P1 P2 P2 ; 6 6 P1 0: MAIN ENCORDER 1: SUB ENCORDER P2 01-99: Steps ENT KEY 1 2 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10 E 1 1 K 2 2 ; 3 3 ENCORDER UP 1 2 3 3 3 4 4 4 5 5 5 6 7 7 7 8 8 8 9 9 9 10 10 10 E 1 1 U 2 2 P1 P2 P2 ; 6 6 P1 0: MAIN ENCORDER 1: SUB ENCORDER P2 01-99: Steps MENU 1 2 3 3 3 4 4 4 5 5 5 6 6 7 7 7 8 nn E 1 X 2 P1 P1 P1 P2 P2 P1 P1 P1 ; 6 ~ 8 8 P2 9 nn ** ; 10 P1 : 001-149 (MENU Number) P2 : Parameter See Table 1 and Table 2 E 1 X 2 E X P1 P1 P1 P2 P2 ~ P2 ** ; FT-2000 SERIES CAT OPERATION REFERENCE BOOK Page 6 CAT (COMPUTER AIDED TRANSCEIVER) OPERATION CONTROL COMMAND TABLES TABLE 1 P1 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 FUNCTION AGC FAST DELAY TIME AGC FAST PEAK HOLD TIME AGC MID DELAY TIME AGC MID PEAK HOLD TIME AGC SLOW DELAY TIME AGC SLOW PEAK HOLD TIME DISPLAY COLOR METER DIMMER DISPLAY DIMMER TUNING OFFSET INDICATOR S-METER PEAK HOLD ROTATOR STARTING POINT ROTATOR NEEDLE PRECISELY QMB MAKER LEVEL INDICATOR VOICE MEMORY AUDIO OUTPUT LEVEL VOICE MEMORY AUDIO TX LEVEL CW BEACON CONTEST NUMBER STYLE CONTEST NUMBER CW MEMORY "1" MEMORY TYPE CW MEMORY "2" MEMORY TYPE CW MEMORY "3" MEMORY TYPE CW MEMORY "4" MEMORY TYPE CW MEMORY "5" MEMORY TYPE ANTENNA SELECTION MODE BEEP LEVEL CAT BAUD RATE CAT TIME-OUT TIMER CAT RTS PORT CAT DATA INDICATOR MEMORY GROUP QUICK SPLIT TUNING OFFSET VFO TRACK TX TIME OUT TIMER TRANSVERTER FREQUENCY DISPLAY -TUNE DIAL SUB (VFO-B) BAND NB LEVEL SUB (VFO-B) BAND CW NARROW FILTER MIC SCAN SCAN RESUME VOX ANTI-TRIP LEVEL FREQUENCY ADJUST SUB (VFO-B) BAND IF SHIFT (LSB) SUB (VFO-B) BAND IF SHIFT (USB) SUB (VFO-B) BAND IF SHIFT (CW-LSB) SUB (VFO-B) BAND IF SHIFT (CW-USB) SUB (VFO-B) BAND IF SHIFT (RTTY-LSB) SUB (VFO-B) BAND IF SHIFT (RTTY-USB) SUB (VFO-B) BAND IF SHIFT (PKT-LSB) SUB (VFO-B) BAND IF SHIFT (PKT-USB) AM MIC GAIN AM MIC SELECT FRONT PANEL KEY JACK TYPE FRONT PANEL KEY JACK WIRING REAR PANEL KEY JACK TYPE REAR PANEL KEY JACK WIRING CW AUTO MODE CW BFO INJECTION SIDE CW BREAK-IN MODE CW CARRIER WAVE FORM SHAPE CW WEIGHT CW FREQUENCY DISPLAY CW PC KEYING CW QSK TIME AFSK MODE DATA INPUT PORT AFSK MODE DATA INPUT LEVEL AFSK MODE DATA OUTPUT BAND AFSK MODE DATA OUTPUT LEVEL PSK MODE VOX DELAY TIME PSK MODE VOX GAIN PACKET MODE FREQUENCY DISPLAY OFFSET PACKET MODE CARRIER POINT FREQUENCY FM MIC GAIN FM MIC SELECT 28 MHz REPEATER SHIFT 50 MHz REPEATER SHIFT RTTY MODE RX POLARITY (MARK/SPACE) RTTY MODE TX POLARITY (MARK/SPACE) RTTY MODE DATA OUTPUT BAND RTTY MODE DATA OUTPUT LEVEL RTTY MODE SHIFT FREQUENCY RTTY MODE MARK FREQUENCY SSB MODE MIC SELECT SSB MODE TX BPF BANDWIDTH MAIN (VFO-A) BAND LSB CARRIER POINT MAIN (VFO-A) BAND USB CARRIER POINT SUB (VFO-B) BAND LSB CARRIER POINT SUB (VFO-B) BAND USB CARRIER POINT AGC GAIN CURVE P2 0020 ~ 4000 msec (20 msec/step) 0000 ~ 2000 msec (20 msec/step) 0020 ~ 4000 msec (20 msec/step) 0000 ~ 2000 msec (20 msec/step) 0020 ~ 4000 msec (20 msec/step) 0000 ~ 2000 msec (20 msec/step) 0: COOL BLUE 1: CONTRAST BLUE 2: FLASH BLUE 3: CONTRAST UMBER 4: UMBER 00 ~ 15 00 ~ 07 0: CLARIFIER OFFSET 1: CW TUNIG METER 2: VRF PEAK POSITION 0: OFF 1: 0.5 sec 2: 1.0 sec 3: 2.0 sec 0: 0° 1: 90° 2: 180° 3: 270° 00 ~ 30° (0 ~ ­30°, 2° step) 0: DISABLE 1: ENABLE 0000000 ~ 1111111 (See Chart of the next page) 000 ~ 100 000 ~ 100 000 (OFF) ~ 255 sec 0: 1290 1: AunO 2: Aunt 3: A2nO 4: A2nt 5: 12nO 6: 12nt 0000 ~ 9999 0: TEXT MEMORY 1: MESSAGE MEMORY 0: TEXT MEMORY 1: MESSAGE MEMORY 0: TEXT MEMORY 1: MESSAGE MEMORY 0: TEXT MEMORY 1: MESSAGE MEMORY 0: TEXT MEMORY 1: MESSAGE MEMORY 0: BAND 1: STACK 000 ~ 100 0: 4800 bps 1: 9600 bps 2: 19200 bps 3: 38400 bps 0: 10 msec 1: 100 msec 2: 1000 msec 3: 3000 msec 0: DISABLE 1: ENABLE 0: DISABLE 1: ENABLE 0: DISABLE 1: ENABLE ­20 ~ +00 (or ­00) ~ +20 kHz 0: OFF 1: BAND 2: FREQUENCY 0: OFF 1: 3 min 2: 5 min 3: 10 min 4: 15 min 5: 20 min 6: 30 min 30 ~ 49 MHz 0: STEP-2 1: STEP-1 2: OFF 1000: NB KNOB 0000 ~ 0100 (FIX) 0: 1200 Hz 1: 500 Hz 2: 300 Hz 0: DISABLE 1: ENABLE 0: PAUSE 1: TIME 000 ~ 100 ­25 ~ +00 (or ­00) ~ +25 ­1000 ~ +0000 (or ­0000) ~ +1000 Hz ­1000 ~ +0000 (or ­0000) ~ +1000 Hz ­1000 ~ +0000 (or ­0000) ~ +1000 Hz ­1000 ~ +0000 (or ­0000) ~ +1000 Hz ­1000 ~ +0000 (or ­0000) ~ +1000 Hz ­1000 ~ +0000 (or ­0000) ~ +1000 Hz ­1000 ~ +0000 (or ­0000) ~ +1000 Hz ­1000 ~ +0000 (or ­0000) ~ +1000 Hz 1000: MIC KNOB 0000 ~ 0100 (FIX) 0: MIC JACK 1: DATA JACK 2: N.C. 0: OFF 1: BUG 2: IAMBIC KEYER W/O ACS 3: IAMBIC KEYER W/ACS 0: NORNAL 1: REVERSE 0: OFF 1: BUG 2: IAMBIC KEYER W/O ACS 3: IAMBIC KEYER W/ACS 0: NORNAL 1: REVERSE 0: OFF 1: 50 MHz ONLY 2: ON 0: USB 1: LSB 2: AUTO 0: SEMI BREAK-IN 1: FULL BREAK-IN 0: 1 msec 1: 2 msec 2: 4 msec 3: 6 msec 25 (1:2.5) ~ 45 (1:4.5) 0: DIRECT FREQUENCY 1: PITCH OFFSET 0: DISABLE 1: ENABLE 0: 15 msec 1: 20 msec 2: 25 mesc 3: 30 msec 0: DATA JACK 1: N.C. 000 ~ 100 0: MAIN (VFO-A) BAND 1: SUB (VFO-B) BAND 000 ~ 100 0030 ~ 3000 msec 000 ~ 100 ­3000 ~ +0000 (or ­0000) ~ +3000 Hz (10 Hz/step) ­3000 ~ +0000 (or ­0000) ~ +3000 Hz (10 Hz/step) 1000: MIC KNOB 0000 ~ 0100 (FIX) 0: MIC JACK 1: DATA JACK 2: N.C. 0000 ~ 1000 kHz (10 Hz/step) 0000 ~ 4000 kHz (10 Hz/step) 0: NORMAL 1: REVERSE 0: NORMAL 1: REVERSE 0: MAIN (VFO-A) BAND 1: SUB (VFO-B) BAND 000 ~ 100 0: 170 Hz 1: 200 Hz 2: 425 Hz 3: 850 Hz 0: 1275 Hz 1: 2125 Hz 0: MIC JACK 1: DATA JACK 2: N.C. 0: 50 - 3000 Hz 1: 100 - 2900 Hz 2: 200 - 2800 Hz 3: 300 - 2700 Hz 4: 400 - 2600 Hz 5: 3000WB ­200 ~ +000 (or ­000) ~ +200 Hz (10 Hz/step) ­200 ~ +000 (or ­000) ~ +200 Hz (10 Hz/step) ­200 ~ +000 (or ­000) ~ +200 Hz (10 Hz/step) ­200 ~ +000 (or ­000) ~ +200 Hz (10 Hz/step) 0: NORMAL 1: SLOPED BYTE 4 4 4 4 4 4 1 2 2 1 1 1 2 1 7 3 3 3 1 4 1 1 1 1 1 1 3 1 1 1 1 1 3 1 1 2 1 4 1 1 1 3 3 5 5 5 5 5 5 5 5 4 1 1 1 1 1 1 1 1 1 2 1 1 1 1 3 1 3 4 3 5 5 4 1 4 4 1 1 1 3 1 1 1 1 4 4 4 4 1 Page 7 FT-2000 SERIES CAT OPERATION REFERENCE BOOK CAT (COMPUTER AIDED TRANSCEIVER) OPERATION