User manual ULINE ECHELON CO2175FF - INSTALL GUIDE

Installation Guide CO2175FF -- Combo® Ice Maker/Refrigerator www.U-LineService.com Phone (414) 354-0300 · FAX (414) 354-7905 Service & Parts Tech Lines Phone (800) 779-2547 · FAX (414) 354-5696 OnlineService@U-Line.com ©2006 U-Line Corporation 08/2006 CO2175FF -- Combo® Ice Maker/Refrigerator Contents Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door Swing/Clearances Information . . . . . . . . . . . . . . Reversing the Door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Other Site Requirements . . . . . . . . . . . . . . . . . . . . . . . . Side-By-Side Installation Instructions . . . . . . . . . . . . . . Custom 1/4'' Door Panel Insert . . . . . . . . . . . . . . . . . . . Full Overlay Door Panel . . . . . . . . . . . . . . . . . . . . . . . . . Checking Door Alignment . . . . . . . . . . . . . . . . . . . . . . Adjusting Door Alignment . . . . . . . . . . . . . . . . . . . . . . Water Supply Connection . . . . . . . . . . . . . . . . . . . . . . . Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . Leveling Information . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation of the CO2175FF . . . . . . . . . . . . . . . . . . . . Relocating the Shelves . . . . . . . . . . . . . . . . . . . . . . . . . Installation Troubleshooting . . . . . . . . . . . . . . . . . . . . . Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Start-Up Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 5 5 5 6 7 7 8 12 12 13 14 14 14 15 15 15 16 16 17 1 Follow Safety Precautions IMPORTANT PLEASE READ all instructions completely before attempting to install or operate the unit. · This unit requires connection to the water supply. Improper hook-up can result in substantial property damage! If you are unsure of your ability to safely connect the water supply to the unit, consult a licensed plumber for assistance. · This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a qualified electrician in accordance with applicable electrical codes. Safety Alert Definitions Safety items throughout this guide are labeled with a Danger, Warning or Caution based on the risk type: DANGER Danger means that failure to follow this safety statement will result in severe personal injury or death. WARNING Warning means that failure to follow this safety statement could result in serious personal injury, or death. CAUTION Caution means that failure to follow this safety statement may result in minor or moderate personal injury, property or equipment damage. www.U-LineService.com 2 08/2006 CO2175FF -- Combo® Ice Maker/Refrigerator General Precautions Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide: 2 Inspect and Plan You have received a carton containing your CO2175FF Ice Maker/Refrigerator with a package inside containing a Use and Care Guide, a Product Registration Card and water connection parts. Complete and mail the Product Registration Card or register online at www.U-LineService.com. Once your unit is installed, keep the Use and Care Guide and this Installation Guide in a safe place for future reference. Your unit is Black, White or Stainless Steel. Black and White units have a reversible door with a slightly contoured handle across the top. They come with a flush mounted door panel that, when removed, will accept a custom 1/4-inch thick door panel or a 3/4-inch thick full overlay door panel. Stainless Steel units are covered with a protective coating and have been ordered left- or righthand hinged. The Stainless doors are not reversible and do not accept custom panels. Please carefully follow the directions that apply to your unit and your intended design. WARNING SHOCK HAZARD -- Electrical Grounding Required. · Keep the unit unplugged throughout installation except during testing. · Never remove the round grounding prong from the plug and never use a two-prong grounding adapter. · Never use an extension cord to connect power to the unit. · Always keep your working area dry. CAUTION · Use care when moving and handling the unit. Use gloves to prevent personal injury from sharp edges. · Do not lift the unit by the door or door handle. · Do not install the unit behind closed doors or in any way that would obstruct airflow to the front grille, which may cause the unit to malfunction. Tools/Materials Required · Screwdrivers -- slotted and Phillips head · 1/4-inch Outside Diameter copper tubing and shut-off valve for water supply line · 1/4-inch thick door panel material and cutting tools (Black or White units) (If installing a 1/4" Panel) · Full Overlay Door Panel Kit (part number U-OL2175B -- Black or part number U-OL2175W -- White), 3/4-inch door panel overlay, cutting tools, drill and bits (Black or White units) (If installing a 3/4" Full Overlay) Inspection Unwrap and inspect the unit on a flat, level surface capable of supporting its entire weight. Removing Protective Coating (Stainless Steel Units Only) When inspecting/installing a Stainless Steel unit, the protective coating covering the unit must be removed first. Start at a corner of the unit/door and pull back the protective coating to remove it from the unit/door. 08/2006 3 www.U-LineService.com CO2175FF -- Combo® Ice Maker/Refrigerator After all the protective coating has been removed from the unit/door, clean all Stainless Steel surfaces with Claire Stainless Steel Polish and Cleaner or comparable product or a mild detergent and warm water solution and soft cloth. Do NOT use abrasive cleaning agents. Note: If cleaning with mild detergent and warm water solution and soft cloth, the unit MUST be treated with Claire Stainless Steel Polish and Cleaner or comparable product to prevent discoloration. 3 Prepare Site Your U-Line product has been designed for either freestanding or built-in installation. When built-in, your unit does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed and clearance is required for water, drain and electrical connections in the rear. Note: Unit can NOT be installed behind a closed cabinet door. Exterior Cleaning (As Required) Black and White Models: · The door, grille and cabinet may be cleaned with a mild detergent and warm water solution. Do not use solvent-based or abrasive cleaners. Use a soft sponge and rinse with clean water. Wipe with a soft, clean towel to prevent water spotting. Stainless Steel Models: · Stainless steel models can discolor when exposed to chlorine gas, pool chemicals, salt water or cleaners with bleach. · Keep your stainless steel unit looking new by cleaning with a good quality all-in-one stainless steel cleaner/ polish on a monthly basis. For best results use Claire Stainless Steel Polish and Cleaner, which can be purchased from U-Line Corporation. (The part number is 173348.) Comparable products are acceptable. Frequent cleaning will remove surface contamination that could lead to rust. Some installations may require cleaning on a weekly basis. · Do not clean with steel wool pads. · Do not use cleaners that are not specifically intended for stainless steel (this includes glass, tile and counter cleaners). · If any surface discolors or rusting appears, clean it quickly with Bon-Ami or Barkeepers Friend Cleanser and a non-abrasive cloth. Always clean in the direction of the grain. Always finish this process with Claire Stainless Steel Polish and Cleaner or comparable product to prevent further problems. · Use of abrasive pads such as Scotchbrite will cause the graining in the stainless to become blurred. · Rust that is allowed to linger can penetrate into the surface of the stainless steel and complete removal of the rust may not be possible. Cut-Out Dimensions See Electrical Specifications for Power Supply 34-1/4" to 35-1/8" 24" 8" 24-3/16" Figure 1 Follow the cut-out drawing in Figure 1. The 24-3/16" width allows 1/4" for ease in installation and removal of the unit. 24" is the cabinet depth in most installations. The unit is 23-11/16" deep including the handle on Black and White models and 23-11/16" deep including the door and not the handle on Stainless Steel models (see Figure 2). www.U-LineService.com 4 08/2006 CO2175FF -- Combo® Ice Maker/Refrigerator Product Dimensions 23-11/16" Including Handle 25-13/16" Including Handle Reversing the Door (Black and White Units Only) All U-Line units (except Stainless Steel models) may be left- or right-hand opening. The door opening is easily reversed by moving the hinge hardware to the opposite side. The top hinge hardware will be used on the bottom of the other side and the bottom hinge hardware will be used on the top of the other side (see Figure 4). To reverse the door: 1. Remove top hinge Figure 4 ULIN_0015_A screw pin from door (Phillips screwdriver) (see Figure 5). Remove door by tilting forward and lifting off bottom hinge pin. 2. Remove plastic screw plugs (3 each, top and bottom) from new hinge location. Do not discard (see Figure 6). 34-1/8" 34-1/8" 23-15/16" Black and White 23-15/16" Stainless Steel Figure 2 Please note that the unit has adjustable feet that can add one additional inch to height during leveling or to match adjacent cabinets (see Figure 37 on Page 14). Door Swing/Clearances Information Black and White units have a zero clearance for the door to open 90° (see Figure 3). Stainless Steel models require a minimum of 2-1/8" door clearance to accommodate the handle if the unit is installed next to a wall or similar type of structure. Wall 1/4" Min. Wall 2-1/8" Min. Screw Plugs 21-7/16" 21-7/16" Figure 6 25-1/2" 90° Door Swing 90° Door Swing 25-1/2" Figure 5 ULIN_0133_A Black and White Stainless Steel 3. Remove top hinge (3 screws), reinstall hinge screw pin, and remount on opposite side BOTTOM (see Figure 7). Figure 3 08/2006 5 www.U-LineService.com CO2175FF -- Combo® Ice Maker/Refrigerator 4. Remove the two door closer inserts from the existing bottom hinge and install as shown on the new bottom hinge (see Figure 8). Other Site Requirements Power Supply The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A circuit (normal household current). See Electrical Specifications on Page 14. 1 Door Closer Inserts Water Supply The unit requires a 1/4-inch Outside Diameter water supply line and a shut-off valve. For more information see Page 13. 2 ULIN_0003_A Environmental Requirements Figure 8 Many U-Line models are designed to operate in harsh outdoor/marine environments. Special considerations include the following: · The units are designed to operate between 50°F (10°C) and 110°F (40°C). High ambient temperatures (110°F [40°C] or higher) may reduce the unit's ability to reach low temperatures and may also reduce the ice production rate for those models with icemakers. · If the ambient temperature is expected to drop below 45°F (7°C), drain all water from the unit to prevent freezing damage not covered by the warranty. · For best performance, keep the unit out of direct sunlight and away from heat generating equipment. · For best performance and life outdoors, place under a counter or provide shelter of some kind. · In climates where high humidity and dew points are present, condensation may appear on outside surfaces. This is considered normal. The condensation will disappear when the humidity drops. Figure 7 5. Remove existing bottom hinge (3 screws) and remount on opposite side TOP. Remove hinge screw pin. 6. Remove the plastic hole plug from the top of the door to allow the pivot pin to be inserted in the new location. Install the plug into the vacated hole on the opposite side. 7. With bottom of door facing up, remove pivot plate (2 screws), flip over, and remount on opposite side of door (see Figure 9). Be sure notch in plate faces center. Figure 9 8. Holding door upright with top of door tilted forward, place hole of door pivot plate on bottom hinge screw pin (see Figure 10). 9. Tilt top of door into position in top hinge and install top hinge screw pin. 10. Install plastic screw plugs removed in Step 2 in old hinge holes (3 each, top and bottom). Figure 10 www.U-LineService.com 6 08/2006 CO2175FF -- Combo® Ice Maker/Refrigerator Side-By-Side Installation Instructions For a complete refreshment center, install your CO2175FF Ice Maker/Refrigerator beside a U-Line Drawer or Wine Captain Model (see Figure 11 for typical cut-out). Note that each Side-By-Side Installation will be different. · Cut-out width for a side-by-side installation is the total of the widths listed under Cut-Out Dimensions in each unit's Installation Guide. For example: Placing a CO2175FF Ice Maker/Refrigerator next to a 2115 series unit would require a cut-out width of: 24-3/16" + 15-3/16" = 39-3/8" Placing a CO2175FF Ice Maker/Refrigerator next to a 2175 series unit would require a cut-out width of: 24-3/16" + 24-3/16" = 48-3/8" · No trim kit is required. However, 1/4-inch space needs to be maintained between the units to ensure unobstructed door swing. · Units must operate from separate, properly grounded electrical receptacles placed according to each unit's Electrical Specifications. Typical Side-By-Side Cut-Out 4 Prepare and Install Door Panel (Black and White Units Only) Two types of custom door panels can be installed on your Black or White unit to harmonize with or accent the surrounding décor: a Custom 1/4" Insert or a Full Overlay. If no custom door panel is used, go on to 5 Adjust Door. Custom 1/4'' Door Panel Insert Door Panel Preparation A custom door panel can be inserted into the doorframe. Custom door panels can be flat or raised, as long as the maximum panel thickness where inserted into the door reveal (channel) is 1/4"-thick. For raised panels, the depth of the reveal is 1/4" on all four sides. IMPORTANT Raised panels will reduce the door's 90° swing/zero clearance if the unit is installed next to a wall or similar type of structure. For 2175 models cut the panel insert to the following dimensions. Custom 1/4" Dimensions: Width: Height: 23-1/32" 27-11/16" For 2115 & CLR2160 models cut the panel insert to the following dimensions. 34-1/4" to 35-1/8" 24" 7" 1/4" Space Between Appliances Custom 1/4" Dimensions: Width: Height: 14-1/32" 27-11/16" 1-1/2" The door panel must not weigh more than 20 lbs. Figure 11 Door Panel Installation Install the insert as follows: CAUTION Use care when handling the insert. Insert edges may be sharp. 1. Remove top hinge screw pin (using a Phillips screwdriver, see Figure 12). Remove door by tilting forward and lifting off bottom hinge pin. 08/2006 7 www.U-LineService.com CO2175FF -- Combo® Ice Maker/Refrigerator Full Overlay Door Panel Door Panel Preparation A full overlay door panel completely covers the doorframe and handle to give a built-in appearance. See your U-Line dealer for the optional Full Overlay Door Panel Kit. 2175 Models: P/N U-OL2175B -- Black P/N U-OL2175W -- White ULIN_0133a_A Figure 12 Figure 13 2115 & CLR2160 Models: P/N U-OL2115B -- Black P/N U-OL2115W --White Appropriate hardware, Modified Handle, Replacement Hinges and a copy of these instructions will be included in the kit. 1. Cut the overlay to the following dimensions (see Figure 15). Full Overlay Dimensions: 2175 Models: Width: 23-3/4" Height: 29-3/4" 2115 & CLR2160 Models: Width: 14-3/4" Height: 29-3/4" 2. Pull door gasket out of groove (top edge of door only). Start in the middle and pull outward, moving toward the edge (see Figure 13). This may take some force. 3. Remove two outside screws holding door handle. Slightly separate door handle from door (see Figure 14). 4. Pull handle up and off. 5. Remove and discard existing panel and cardboard spacer. 6. Slide custom door panel insert into 1/4-inch channel in door front. 7. Holding door gasket out of the way, replace handle Figure 14 on door, making sure it is seated properly on insert and that screw holes line up. 8. Install two small screws removed in Step 3. 9. Starting at the corners and working inward, push door gasket into place on door. 10. Place door on bottom hinge pin and install upper hinge screw. The door panel must not weigh more than 20 lbs. 3/4" 31/32" 1/8" Relief Notch for Pivot Plate Rear View of Wood Panel Height Width Figure 15 ULIN_0400_A IMPORTANT Rear View of wood panel for right-hand hinge shown. Use mirror image for left-hand hinges. 2. Create a relief (Figure 15) for pivot plate by cutting notch in top corner of overlay panel. Refer to Figure 16 for exact specifications. www.U-LineService.com 8 08/2006 CO2175FF -- Combo® Ice Maker/Refrigerator Installation Instructions 15/32" ø 0.177" (#16 Drill) 11/16" Deep 3/8" 31/32" .125" 11/16" Ref BACK VIEW 1/4" Ref TOP VIEW Removing Existing Door 1. Remove the door shelves by first pulling shelves up at a 45° angle, then straight out. 2. Remove top hinge screw pin (Phillips screwdriver). Remove the door by tilting forward and lifting off the bottom hinge pin. 3. Pull door gasket out of the groove (top edge of door only). Start in the middle and pull outward, moving toward the edge (see Figure 17). This may take some force. Old Handle 3/4" Min Ref 3/8" SIDE VIEW 13/32" BOTTOM VIEW New Handle ø 5/16" x 1/4" Deep Chamfer 1/32" x 45° ULIN_0401_A Figure 16 Route notch in top corner of overlay panel as shown (see Top and Side Views). Top of notch is entire depth of panel, front to back. Width: 31/32" Depth: 1/8" Figure 17 Figure 18 ULIN_0403_A 4. Remove the two screws located on both sides of the handle. 5. Remove the handle and discard. (This handle will be replaced with the Overlay Handle included in the Full Overlay Door Panel Kit.) CAUTION Be careful not to drill too deep! Drilling holes too deep may destroy your door panel. 3. Drill hole for upper door hinge (top of panel) (see Figure 16, Top View). 0.177" diameter (#16 drill) x 11/16" deep 4. Drill hole for lower door hinge (see Figure 16, Bottom View). 5/16" diameter x 1/4" deep 6. Slide the existing door panel out of the doorframe. Attaching the Full Overlay Panel 1. Place and tape the existing door panel on the back of the overlay panel (see Figure 19) and drill holes through both panels according to Figure 20. Remove tape adjoining the panels and enlarge the six holes in the steel (black/white vinyl color) panel using a 0.201" (#7) drill. 2. If a user-supplied cabinet handle will be used, attach its hardware to the overlay panel at this time. Removed Door Panel CAUTION It is important to ensure that all drilled holes are drilled to the correct depth in order to avoid splits in the wood when hardware is installed. 1-3/4" Top Back of Wood Panel Tape Side of Wood Panel Top of Wood Panel 3/8" Both Sides Figure 19 08/2006 9 www.U-LineService.com CO2175FF -- Combo® Ice Maker/Refrigerator 2-5/8" ± 1/4" IMPORTANT Door panel and overlay panel must be aligned properly or the door will not operate correctly. Assembling the Door Drill ø 5/32" x 3/8" Deep 7 Places Model 2175 6 places Model 2115 and CLR2160 For use with #10 x 5/8" Wood Screw and Nylon Spacer 15-9/16" ± 1/4" 1. Install the assembled panel by sliding the original door panel back into the doorframe. 2. Replace the Overlay Handle and secure with the two screws removed in Step 4 under Removing Existing Door. 28-7/8" ± 1/4" 3. Attach Overlay cap to door, opposite side of where hinges will be (see Figure 23). Overlay Cap 1" 11-7/8±1/32 For use on Model 2175 Only 3/4" Wood Panel 1" ULIN_0402_A Replacement Handle Figure 20 Attach the door panel to the overlay panel using #10 x 5/ 8" wood screws and nylon spacers. The nylon spacers fit between the overlay panel and the door panel as shown in Figure 21. The spacers allow the original door panel to slide back into the 1/4"-thick door reveal (channel). Typical Wood Panel Door Panel #8-32 x 1/2" Flat Head Screws Black, Two Places Figure 23 4. Attach Top Pivot Plate to door handle, on side where hinges will be. Use the two #8-32 x 1/2" Flat Head Phillips screws (Black) supplied with kit (see Figure 24). 3/4" Wood Overlay #10 x 5/8" Round Head Screw Seven Required Top Pivot Plate Screw to attach Handle Removed in step 4 Figure 21 Plastic Spacer Seven Required Figure 24 5. Starting at the corners and working toward the center, push the door gasket back into place. Installing the Door 3. Remove the existing bottom pivot plate and replace with the Full Overlay pivot plate (see Figure 22). Existing Door Existing Bottom Pivot Plate (Remove and Discard) Wood Panel Bottom Pivot Plate (5/8" Longer Than Existing Bottom Pivot Plate, Flush Side Facing Out) #8-32 x 3/8" SEMS Hex Screw Two Places 1. Remove the existing hinges from the unit, saving the door closure assembly. 2. Install the new Replacement Top Hinge onto the unit (see Figure 25). Figure 22 www.U-LineService.com 10 08/2006 CO2175FF -- Combo® Ice Maker/Refrigerator Checking Door Alignment Wood Panel Top Hinge Plate (5/8" Longer than Existing Top Hinge Plate) Pivot Post The unit's door is aligned at the factory before shipment. However, its alignment could have been disturbed during shipment or during door panel installation. IMPORTANT #8-32 x 1/2" Flat Head Screw Three Places Properly aligned, the door should be 1/8" below the top of the unit's cabinet, NOT flush with the top (see Figure 28). Top Pivot Plate 1/8" Figure 25 Door Panel ULIN_0405 3. Install the pivot post into the new Replacement Bottom Hinge (using the Phillips screwdriver) and install the hinge onto the unit. 4. Replace the door closure assembly onto the bottom pivot post (see Figure 26). Be sure that bosses on closers align with holes in hinge and hinge plate. Figure 27 1. Compare the top edge of the door to the top edge of the cabinet. 2. If the door edge is 1/8" below and parallel to the top of the cabinet, the door is aligned. If it is not, note whether the side opposite the hinge needs to be moved UP or DOWN, and use the following procedure. 3. If door is adjusted correctly, but panel is not square with the adjacent cabinets, slight adjustments can be made by drilling the holes in the vinyl coated steel panel slightly oversized. See Figure 20 on Page 10. Door Closure Top Boss Existing Door Door Closure Bottom Boss Pivot Post #8-32 x 1/2" Flat Head Screw Three Places Wood Panel Bottom Hinge Plate (5/8" Longer than Existing Bottom Hinge Plate) Figure 26 IMPORTANT Pivot posts must be cleaned. Closers must also be clean and greased to ensure proper operation. 5. Place the modified door onto the pivot post. 6. Position door and install the pivot post into the top hinge (using the Phillips screwdriver). 7. Adjust door as needed for proper closure. 8. Check to see that light goes off when the door closes. 9. Reinstall the door shelves by lining up the bosses and first pushing straight in, then down at a 45° angle. 08/2006 11 www.U-LineService.com CO2175FF -- Combo® Ice Maker/Refrigerator 5 Adjust Door Checking Door Alignment The unit's door is aligned at the factory before shipment. However, its alignment could have been disturbed during shipment or during door panel installation. Slotted Mounting Holes Notch IMPORTANT Properly aligned, the door should be 1/8" below the top of the unit's cabinet, NOT flush with the top (see Figure 28). Raise Outside Door Edge Lower Outside Door Edge Figure 30 1/8" Figure 28 1. Compare the top edge of the door to the top edge of the cabinet. 2. If the door edge is 1/8" below and parallel to the top of the cabinet, go on to 6 Prepare Plumbing. If it is not, note whether the side opposite the hinge needs to be moved UP or DOWN, and use the following procedure. Note: If door is adjusted correctly, but panel is not square with the adjacent cabinets, slight adjustments can be made by drilling the holes in the vinyl coated steel panel slightly oversized. See Figure 21 on Page 10. 3. See Figure 30. If the top far edge of the door needs to move UP, move the hinge plate toward the outside of the door and retighten screws. If the top far edge of the door needs to move DOWN, move the hinge plate toward the inside of the door and retighten screws. 4. Mount the door to recheck alignment and repeat Steps 2 and 3 if further adjustment is necessary. 5. When top edge of door is parallel to top edge of cabinet, remove the door and ensure the two screws are secure. 6. Remove the door closers from the bottom hinge, clean thoroughly and lubricate the mating surfaces with petroleum jelly. 7. Reinstall the closers, lining up the bosses with holes in hinge and hinge plate (see Figure 31). 8. Mount the door, install top hinge pivot pin and go on to 6 Prepare Plumbing. Door Closer Inserts Adjusting Door Alignment 1. Remove top hinge screw pin (Phillips screwdriver, see Figure 29). Remove door by tilting forward and lifting off bottom hinge pin. 2. With door upside-down, loosen but do not remove the two screws on the door's bottom hinge plate. Boss Figure 31 Figure 29 ULIN_0133_A www.U-LineService.com 12 08/2006 CO2175FF -- Combo® Ice Maker/Refrigerator 6 Prepare Plumbing CAUTION Plumbing installation must observe all state and local codes. All water connections MUST BE made by a licensed/ qualified plumbing contractor. Failure to follow recommendations and instructions may result in damage and/or harm. 2. Locate the compression fitting and ferrule packed with the unit. Slide the compression fitting and ferrule over the 1/4-inch OD water supply line. Do not use thread sealing compound or tape. Using two wrenches, tighten the compression fitting on the supply line (see Figure 33). 3. Carefully bend the water supply line into position and connect the line to the solenoid valve (see Figure 34). Avoid kinking the water supply line. WARNING To prevent accidental electrocution, make certain that the floor surfaces surrounding the unit are dry whenever power is removed from, or applied to, the unit. Water Supply Connection When connecting the water supply, follow these guidelines: · Review the local plumbing codes before you install the unit. · Connect to the cold water supply. · The water pressure should be between 20 and 120 psi. · Install a shut-off valve in the 1/4 inch Outside Diameter water supply line. · Connect sufficient tubing to the unit so that tubing may be looped, allowing the unit to be removed for cleaning and servicing (see Figure 34). However, make certain that the tubing is not pinched or damaged during installation. Note: U-Line recommends the use of copper tubing for installation. The use of other types of tubing is not recommended due to potential aftertaste & deterioration over time. To connect to water supply: 1. Install the 1/4 inch OD copper water line from the main water source (see Figure 32). Figure 34 IMPORTANT Normal operation creates some vibration. A water supply line contacting cabinet wall may cause excessive noise during operation or damage to the line. 4. For recessed installations, allow extra water supply line length to provide slack for easy removal from the recessed area (see Figure 34). This will also safeguard against kinking the line. 5. Go on to 7 Prepare Power Supply. Water Connection Figure 32 Figure 33 08/2006 13 www.U-LineService.com CO2175FF -- Combo® Ice Maker/Refrigerator 7 Prepare Power Supply 8 Level the Unit Electrical Specifications CAUTION Electrical installation must observe all state and local codes. This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a qualified electrician. The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A power supply (normal household current). An individual, properly grounded branch circuit or circuit breaker is recommended. GFCI (ground fault circuit interrupter) is usually not required for fixed location appliances and is not recommended for your unit because a GFCI could be prone to nuisance tripping. However, be sure to consult your local codes. See Figure 35 for recommended receptacle location. Leveling Information IMPORTANT It is extremely important that the unit is level. If it is not level, the ice mold will not fill evenly. 1. Use a level to check the levelness of the ice maker from front to back and from side to side. Level should be placed along top edge and side edge as shown (see Figure 36). 1 Figure 36 ULIN_0193_A 2. If the ice maker is not level, adjust the feet on the corners of the unit as necessary (see Figure 37). 24" 7" 1-1/2" Turn Foot to Adjust Figure 35 Figure 37 3. Check the levelness after each adjustment and repeat the previous steps until the unit is level. Go on to 9 Install the Unit. WARNING SHOCK HAZARD -- Electrical Grounding Required. · Never remove the round grounding prong from the plug and never use a two-prong grounding adapter. · Never use an extension cord to connect power to the unit. Go on to 8 Level the Unit. Installation Tip If the room floor is higher than the floor in the cut-out opening, adjust the rear feet to achieve a total unit rear height of 1/8" less than the opening's rear height. Shorten the unit height in the front by adjusting the front feet. This allows the unit to be gently tipped into the opening. Readjust the front feet to level the unit after it is correctly positioned in the opening. www.U-LineService.com 14 08/2006 CO2175FF -- Combo® Ice Maker/Refrigerator 9 Install the Unit Door Shelves 1. First pull shelf up at a 45° angle, then straight out (see Figure 39). 2. Choose new location and line up on bosses. First push straight in, then down at a 45° angle. Boss Installation of the CO2175FF 1. Open the water supply valve in the main water source. 2. Plug in the powercord. 3. Open the door and press the POWER icon (see Figure 40,1). to turn the unit OFF. Note: If the unit is NOT turned OFF, water will immediately start flowing into the unit when it is first plugged into the electrical outlet. 4. Gently push the unit into position. Be careful not to kink the water supply line or entangle the electrical cord. 5. Re-check the leveling, from front to back and side to side. Make any necessary adjustments. The unit's top surface should be approximately 1/8" below the countertop. 6. Remove the tape from the glass shelves and wipe out the inside of the unit with a clean, water-dampened cloth. Notch Figure 39 Installation Troubleshooting Q: A: Problem Water is leaking under the unit. Solution Relocating the Shelves Both the glass shelves in the refrigerator and the inner door shelves can be moved to accommodate your bottles, cans and containers. A water leak under the unit is most likely caused by a bad connection in the water supply line. Make sure the water line's brass fitting is screwed tight to its valve and threaded correctly. Glass Shelves on Right-Hand Hinge Units 1. Open door fully, grasp shelf firmly, lift front edge slightly, and pull straight out. 2. Choose new location and slide shelf onto the appropriate rib. Q: A: Problem The door remains open unless it is pushed closed. Solution Glass Shelves on Left-Hand Hinge Units 1. See Figure 38. Pull shelf out about 6" to clear the wall's molded protrusion. 2. Tilt right-hand edge of shelf up. 3. Keeping at this angle and hugging the right wall, pull the shelf out. 4. Choose new location and insert over ribs, tilting right-hand edge up. Push in, then lower shelf onto ribs. 1. Pull Out 6" 3. Pull 2. Tilt The hinges should be self-closing when the door is open approximately 8". If this is not the case, make sure the closers (at the bottom of the hinge pin) are clean, greased and installed correctly. Also, re-check leveling from front to back of the unit and readjust if necessary. Make sure that pivot plate is installed correctly. Q: A: Problem The custom overlay door was designed to align with the rest of the cabinet doors, but the unit has crept forward. Solution Make sure that the electrical cord and water supply line are not obstructing the installation. Figure 38 08/2006 15 www.U-LineService.com CO2175FF -- Combo® Ice Maker/Refrigerator 10 Start-Up for the First Time About Settings No adjustments should be necessary at this time. For information about Adjusting the Temperature Control and Adjusting the Cube Size, see the Use and Care Guide. Initial Start-Up Once installation and leveling is complete, the unit is ready for initial start-up and operation. The POWER icon is located inside the unit.(see Figure 40,1). Start-Up Troubleshooting Q: A: Problem 1 2 3 4 5 Unit does not appear to turn on when POWER icon is pressed. Solution ULIN_0058_A Figure 40 1. The unit should already be plugged into the electrical outlet. Make sure the water supply is turned on. 2. Open the door and press the POWER icon on the display to turn the unit on (see Figure 40,1). 3. As soon as the ice maker mold reaches the proper Figure 41 temperature, the ice maker mechanism will fill the mold with water. Note: The first cubes may be small because of air in the water line. After two hours, cubes will be standard size. 4. The ice maker will continue to produce until the bin is full. You may interrupt production by raising the bin arm into an upright and locked position (see Figure 41). While the bin arm is locked, the unit will maintain temperature for ice storage. Make sure unit is plugged in and outlet has power (circuit breaker has not tripped). Remember that the ice maker mechanism will not fill the mold with water until the mold reaches the proper temperature. Q: A: Q: A: Problem Water does not appear to be flowing into unit. Solution Check that the water is connected and turned on and the line is not obstructed. Problem The cubes produced during the first two to three hours of operation have been discarded. New cubes still appear cloudy. Solution This is normal and is caused by air being trapped in the cube during fast freezing. IMPORTANT See the Use and Care Guide's Troubleshooting Guide for more solutions. IMPORTANT It is possible that dirt or scale will dislodge in the water line. Always throw away all ice cubes made during the first twenty-four (24) hours of operation. CAUTION · The ice bucket MUST be fully inserted to avoid freezing products in the refrigerator section. The ice bin door must be fully closed with the door lip inside the ice bucket. · Do not place cans or bottles so they are touching the back wall of the refrigerator section, as they may freeze. · Do not place any objects over air inlet or outlet in the freezer section. www.U-LineService.com 16 08/2006 Who to Call Service Information If the need for service arises, call the U-Line Customer Care Center directly @ 800-779-2547. To ensure accurate assistance, please have your Model Number and Serial Number and an explanation of the problem. The Model and Serial Number plate is located inside unit at upper right hand corner. If you need to locate a service company, you can go online at www.U-LineService.com and search for a service company by zip code. For more than four decades, U-Line has distinguished itself as the leader in built-in undercounter ice making, refrigeration and wine storage appliances. U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in undercounter icemakers, Combo® icemaker/refrigerators, Wine Captain® wine storage units, refrigerators, refrigerated drawers and refrigerator/freezers. ©2006 U-Line Corporation Publication No. 30150E 08/2006 Rev. B