AXIS 207 AXIS 207W AXIS 207MW Installation Guide ENGLISH FRANCAIS DEUTSCH ITALIANO ESPAÑOL AXIS 207/207W/207MW Installation Guide Page 3 AXIS 207/207W/207MW Installation Guide This installation guide provides instructions for installing the AXIS 207/207W/207MW Network Camera on your network. For all other aspects of using the product, please see the User's Manual, which is available on the CD included in this package, or from www.axis.com/techsup Installation steps 1. 2. 3. 4. 5. 6. 7. Check the package contents against the list below. Hardware overview. Familiarize yourself with the camera. See page 4. Install the hardware and make all cable connections. See page 7. Set an IP address. See page 8. Set the password. See page 12. Important! Configure the wireless connection. See page 13. This product must be used in Adjust the focus. See page 15. compliance with local laws and regulations. ENGLISH ENGLISH 1. Package contents Item Network camera Models/variants/notes AXIS 207 AXIS 207W AXIS 207MW AXIS 207: type PS-L AXIS 207MW/AXIS 207W: type PS-H 1.8 meters Indoor power supply (country specific) Power supply extension cable Camera stand Flexible clamp Terminal block connector Cable clip CD Printed Materials Supplied with 3 mounting screws. The extension section is ready fitted. For shelf mounting 4-pin connector block for connecting external devices to the I/O terminal connector Self-adhesive - fixes to back panel for holding power cable Axis Network Video Product CD, including installation tools and other software, product documentation AXIS 207/207W/207MW Installation Guide (this document) Axis Warranty Document Page 4 AXIS 207/207W/207MW Installation Guide 2. Hardware overview Focus ring Antenna (wireless models) Status indicator LED (outer ring) Microphone I/O terminal connector (see page 5) Product ID & Serial number (S/N). The serial number may be required during the installation. Lock ring Network indicator LED Control button Network connector (see page 5) Wireless indicator LED (wireless models) Power connector (see page 5) Power indicator LED Dimensions AXIS 207: HxWxD = 85 x 55 x 34mm (3.3" x 2.2" x 1.3") Weight = 177g (0.39 lb) (stand included, power supply excluded) AXIS 207W/MW: HxWxD = 85 x 55 x 40mm (3.3" x 2.2" x 1.6") (antenna excluded) Weight: 190g (0.42 lb) (stand included, power supply excluded) AXIS 207/207W/207MW Installation Guide Page 5 Unit connectors Network connector - RJ-45 Ethernet connector. Supports Auto-MDIX (AXIS 207W/MW only) for automatic detection of straight or crossover cable. Using shielded cables is recommended. Power connector - Mini DC connector. 4.9-5.1V DC, max 4.0W. See product label for ± connection. I/O terminal connector - Used in applications for e.g. motion detection, event triggering, time lapse recording, alarm notifications, etc. It provides the interface to: · 1 transistor output - For connecting external devices such as relays and LED:s. Connected devices can be activated by Output buttons on the Live View page or by an Event Type. The output will show as active (in Event Configuration > Port Status) if the alarm device is activated. 1 digital input - An alarm input for connecting devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a signal is received the state changes and the input becomes active (shown under Event Configuration > Port Status). Auxiliary power and GND Pin number Pin 4 Notes Uses an open-collector NPN transistor with the emitter connected to the GND pin. If used with an external relay, a diode must be connected in parallel with the load, for protection against voltage transients. Connect to GND to activate, or leave floating (or unconnected) to deactivate. Ground Electrically connected in parallel with the connector for the power supply, this pin provides an auxiliary connector for mains power to the unit. This pin can also be used to power auxiliary equipment, with a maximum current of 50mA. 1 4 ENGLISH ENGLISH · · Function Transistor Output Specifications Max load = 100mA Max voltage = 24V DC (to the transistor) Digital Input Pin 3 Must not be exposed to voltages greater than 10V DC GND Auxiliary DC Power Input Pin layouts AXIS 207 4 1 AXIS 207 = Pin 2 AXIS 207W/MW = Pin 1 AXIS 207 = Pin 1 AXIS 207W/MW = Pin 2 Voltage = 4.9-5.1V DC (all models) Min power: AXIS 207: 2.5W AXIS 207W: 3.5W AXIS 207MW: 4.0W AXIS 207MW AXIS 207W Page 6 AXIS 207/207W/207MW Installation Guide Connection diagram Fuse: AXIS 207: 500mA AXIS 207W/MW: 1A 3.3V Linear Power Supply Fuse +2 o o1 o GND Power - see table above. 2 e.g. pushbutton Relay o o 1 3 4 o o o Device o oo IMPORTANT! This diagram applies to the AXIS 207W and AXIS 207MW. The AXIS 207 has a different pinout and power - see the table above. Camera LED indicators LED Wireless Color Unlit Green Red Network Green Amber Unlit Status Green Indication Wired mode. Steady for connection to a wireless network. Flashes for network activity. Steady for no wireless network connection. Flashes when scanning for wireless networks. Steady for connection to a 100 Mbit/s network. Flashes for network activity. Steady for connection to 10 Mbit/s network. Flashes for network activity. No wired network connection, or AXIS 207MW/AXIS 207W in wireless mode. Steady green for normal operation. Note: The Status LED can be configured to be unlit during normal operation, or to flash only when the camera is accessed. To configure, go to Setup > System Options > LED settings. See the online help files for more information. Steady during startup, during reset to factory default or when restoring settings. Slow flash for failed upgrade. Normal operation. Flashes green/amber during firmware upgrade. Amber Red Power Green Amber AXIS 207/207W/207MW Installation Guide Page 7 3. Install the hardware ! IMPORTANT! - The AXIS 207/207W/207MW is designed for indoor use only, and must always be positioned where it is not exposed to direct sunlight or strong halogen light, which can cause permanent damage to the camera's image sensor. Damage as a result of exposure to strong light is not covered by the Axis warranty. 3a. Mount the camera Make a note of the serial number (S/N) located on the product label. This number may be required during installation. ENGLISH ENGLISH Wall mounting 1. If required, use the 3 supplied screws to fix the base plate to a flat (horizontal or vertical) surface. 2. To use a shorter stand, unscrew the lock ring to release the camera, and remove the extension section. 3. Attach the camera, adjust the angle and tighten the lock ring. Shelf mounting 1. Position the clamp and tighten the fixing screw securely. 2. Attach the clamp to the lock ring on the camera. 3. Adjust the angle and tighten the lock ring. 3b. Connect the cables 1. Using the self-adhesive strip, attach the supplied cable clip to the rear panel and fasten the power cable to it. This will prevent accidental cable disconnection. 2. Connect the camera to the network using a shielded network cable. For the wireless models, this connection is temporary and allows the camera's settings to be configured via the wired network before connecting to the wireless network. 3. Optionally connect external devices, e.g. alarm devices. See page 5 for information on the terminal connector pins. 4. Connect power, using one of the methods listed below: · Connect the supplied indoor power supply to the power connector on the camera. · Connect power via the terminal connector. See page 5 for information on the terminal connector pins. 5. Check that the indicator LED:s indicate the correct conditions. See the table on page 6 for further details. Note that some LED:s can be disabled and may be unlit. Page 8 AXIS 207/207W/207MW Installation Guide 4. Set an IP address To make it accessible on the network, the AXIS 207/207W/207MW must be assigned an IP address. Depending on the number of cameras you wish to install, the recommended method for setting IP addresses in Windows is either AXIS IP Utility or AXIS Camera Management. Use the method that best suits your purpose. Both of these free applications are available on the Axis Network Video Product CD supplied with this product, or they can be downloaded from www.axis.com/techsup Method AXIS IP Utility See page 9. AXIS Camera Management See page 10. Recommended for Single cameras Small installations Multiple cameras Large installations Installations on other subnets Operating system Windows Windows 2000 Windows XP Pro Windows 2003 Server Notes: · · · · A network DHCP server is optional. The AXIS 207/207W/207MW has the default IP address 192.168.0.90 If setting the IP address fails, check that there is no firewall blocking the operation. For other methods of setting or discovering the IP address of the AXIS 207/207W/207MW, e.g. in other operating systems, see page 11. AXIS 207/207W/207MW Installation Guide Page 9 AXIS IP Utility - single camera/small installation AXIS IP Utility automatically discovers and displays Axis devices on your network. The application can also be used to manually set a static IP address. Note that the computer running AXIS IP Utility must be on the same network segment (physical subnet) as the AXIS 207/207W/207MW. Automatic discovery 1. Check that the AXIS 207/207W/ 207MW is connected to the network and that power has been applied. 2. Start AXIS IP Utility. 3. When the camera appears in the window, double-click it to open its home page. 4. See page 12 for instructions on how to set the password. ENGLISH ENGLISH Set the IP address manually 1. Acquire an unused IP address on the same network segment your computer is connected to. 2. Click the button Set IP address using serial number and enter the serial number and IP address for the AXIS 207/207W/207MW. The serial number is located on the product label. 3. Click the Set IP button and follow the instructions. 4. Click View Home Page button to access the camera's web pages. 5. See page 12 for instructions on how to set the password. Page 10 AXIS 207/207W/207MW Installation Guide AXIS Camera Management - multiple cameras/large installations AXIS Camera Management can automatically find and set IP addresses, show connection status, and manage firmware upgrades for multiple Axis video products. Set the IP address for a single device 1. Check that the camera is connected to the network and that power has been applied. 2. Start AXIS Camera Management. When the AXIS 207/207W/ 207MW appears in the window, double-click it to open the camera's home page. 3. See page 12 for instructions on how to set the password. Set the IP address in multiple devices AXIS Camera Management speeds up the process of assigning IP addresses to multiple devices, by suggesting IP addresses from a specified range. 1. Select the devices you wish to configure (different models can be selected) and click the Assign IP button. 2. Select Obtain IP addresses automatically (DHCP), click the Update button and the program will search in the specified range and suggest an IP address for each device. -orEnter the range of IP addresses, the subnet mask and default router that devices can use and click the Update button. AXIS 207/207W/207MW Installation Guide Page 11 Other methods of setting the IP address The table below shows the other methods available for setting or discovering the IP address. All methods are enabled by default, and all can be disabled. Use in operating system UPnPTM Bonjour Windows (ME or XP) MAC OSX (10.4 or later) All Notes When enabled on your computer, the camera is automatically detected and added to "My Network Places." Applicable to browsers with support for Bonjour. Navigate to the Bonjour bookmark in your browser (e.g. Safari) and click on the link to access the camera's web pages. A free service from Axis that allows you to quickly and simply install your camera. Requires an Internet connection with no HTTP proxy. See www.axiscam.net for more information. See below. The command must be issued within 2 minutes of connecting power to the camera. To view the admin pages for the network DHCP server, please see the server's own documentation. ENGLISH ENGLISH AXIS Dynamic DNS Service ARP/Ping View DHCP server admin pages All All Set the IP address with ARP/Ping 1. Acquire an IP address on the same network segment your computer is connected to. 2. Locate the serial number (S/N) on the AXIS 207/207W/207MW label. 3. Open a Command Prompt on your computer and enter the following commands: Windows syntax arp -s ping -l 408 -t UNIX/Linux/Mac syntax Windows example arp -s 192.168.0.125 00-40-8c-18-10-00 ping -l 408 -t 192.168.0.125 UNIX/Linux/Mac example arp -s temp arp -s 192.168.0.125 00:40:8c:18:10:00 ping -s 408 temp ping -s 408 192.168.0.125 4. Check that the network cabl ...