Installation Guide 1. Contents 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Symbols used in the Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Safety and Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Connection schematic for the OnlinePro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Installation of the GPS/GSM antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Installation of the hands-free microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Installation of the GSM/GPS Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Connection of the reverse signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Connection of the speed signal (GAL) from the speedometer/ tachometer . . . . . . . . . . . . . . 43 Installation/ Removal of the OnlinePro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Initial operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Service Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Subject to errors and technical changes 31 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide 2. Symbols used in the Installation Guide G denotes instructions which are important for your safety and the safety of others. denotes instructions which are important for the installation and function of the unit. 3. Safety and Installation Instructions The OnlinePro should only be installed by trained personnel. · Disconnect the vehicle battery before installation of the unit. Note the safety instructions of the vehicle manufacturer (airbags, immobilisers etc.). Ensure that leads are installed in such a manner that they cannot be pinched, bent or pulled out. Before installation, park the vehicle in a safe and level place and remove the ignition key. If using branch connections, it is important to note the relevant cable section. G · · · Subject to errors or technical changes 32 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide 4. Connection schematic for the OnlinePro Speed signal Earphone Optional GSM Antenna GPS Hands-free microphone Reverse signal Power supply Sound system / loudspeaker antenna Radio CD changer Optional GPS/GSM Box OnlinePro Note: Connection options are described in detail on page 57. Subject to errors and technical changes 33 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide 5. Installation of the GPS/GSM antenna The antenna delivered with the system is a two-piece combination GSM/GPS antenna. The combination GSM/GPS antenna is a glassadhesive antenna; i.e. no leads must be run from the outside to the vehicle interior. Windscreen or rear window D E The GSM/GPS combination antenna consists of an internal unit A and F an external unit B. To ensure correct function, the two units must be installed as described below: Attached to the internal unit A is a 3-metre long cable C with the combined GSM/GPS plugs. The connecting cable B is connected to the GSM/GPS Box with the GSM/GPS plugs. If more than 3 metres of cable are required, the cable can be extended with the optionally available extension cable (Stock No. 1380311). The antenna D can be loosened F to adjust the angle E by twisting the antenna. After loosening and adjusting, the antenna D must be screwed on hand-tight. A C ) The angle of the antenna to the vehicle has an influence on the antenna's transmission and reception. If reception is still unsatisfactory after installation, the angle of the antenna to the vehicle can be adjusted to optimise reception. In most cases, best results are achieved with the antenna in a vertical position. Subject to errors or technical changes 34 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide Installation of the GSM/GPS Antenna G The antenna is to be affixed in such a manner that it cannot detach in the event of a collision or sudden braking. ) (1) The antenna can only be installed under a non-metallised windscreen or rear window. The installation of the GSM/GPS antenna on sharply angled windows (i.e. side windows or rear window in estate cars/ stations wagons) is not recommended as satisfactory GPS reception cannot be ensured. Possible antenna positioning Rear window Subject to errors and technical changes 35 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide a. Determine installation position (1) (rear window, windscreen) (2) Slot faces upwards. Windscreen/Rear window Protective paper (A) (B) ) The antenna must not be affixed over the heating wires of heated windscreens or rear windows. Windows with metal layered plastic window tinting are not suitable. Take the windscreen-wiper range into account when positioning the antenna. The glass surface to which the antenna must adhere, may be slightly curved. When selecting position for installation, please bear in mind the possibility of cable extension. Subject to errors or technical changes 36 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide G The driver's field of vision must not be obstructed. G Clean adhesion surfaces (inside and outside) with the enclosed cleaning cloth. After cleaning, wait until the cleaned surfaces have dried. b. Completely pull off protective paper from the adhesive surface (the square piece as well) (2). Caution: The adhesive part is now exposed. First adhere the external unit (A) with the slot at the top to the glass by firmly pressing (approx. 3-5 seconds) around the circumference of the external unit base. Subsequently, affix internal unit (B) to the inside of the window, once again by pressing on the housing of the unit for approx. 3-5 seconds, with the circular area centred in the middle of the outside unit (centre point = centring axis). Depending upon the amount of space, the position of the internal unit can be turned on this centring axis before being directly affixed. ) The ideal adhesion temperature is between +15 °C and +25 °C. The adhesive foil will adhere immediately to the adhesion surface and cannot be repositioned. It is not possible to reuse the adhesive foil. c. Run connecting cable to the installation position of the GSM/GPS Box. Subject to errors and technical changes 37 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide 6. Installation of the hands-free microphone The hands-free microphone should be placed in the vehicle to allow optimal recognition of the speaker's voice. Possible positions in the vehicle for the microphone can be seen in the following diagram. ) The installation position should be as far away from the loudspeakers as possible. If problems occur, different positions should be tested. In order to pick up as little background noise as possible, the microphone has a narrow pick-up angle and must consequently be directed towards the driver. A: B: C: D: E: F: G: Optimal installation position Alternative installation position Less suitable installation position Speaking direction on microphone Adhesive strip for affixing to smooth surfaces Screw for fastening the screw-on plate Screw-on plate for affixing to rough or uneven surfaces. Affixing the hands-free microphone to a flat and smooth surface can be accomplished with the adhesive strip E (Clean adhesion surfaces). If the microphone is to be affixed to a rough or uneven surface, the screw-on plate G should be affixed first with the screw F (To avoid risk of damage, please pay attention to screw length). Subsequently, affix the microphone to the screw-on plate G with the adhesive strip E. The connection of the hands-free microphones takes place in socket C of the OnlinePro. 38 Subject to errors or technical changes Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide Install the lead in such a manner that it cannot be pinched, bent or pulled out. Connection of the hands-free microphone to the OnlinePro a. Connection without CD changer For connection of the hands-free microphone to an OnlinePro without CD changer, the enclosed blue socket must be connected as described below. Before connection, remove protective cap A from both contacts. b. Connection with CD changer For connection of the hands-free microphone to an OnlinePro with CD changer, the enclosed blue socket must be connected with the two leads as described below. Before connection, remove protective cap A from both contacts. ) Once the contacts are inserted into the blue plug housing, a special tool is required to remove them. Connection of the blue plug housing Socket C A Socket C3 13 Pin 13 14 Colour White Yellow Function NF Earth 14 Subject to errors and technical changes 39 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide 7. Installation of the GSM/GPS Box The connectors for the combination GSM/GPS antenna, the optional operating headset and connecting cable to the OnlinePro are to be connected to the GSM/GPS Box. The SIM card necessary for activation and operation of the telephone must be inserted into the card-holding slot. A: Retaining cover over SIM card holder B: Connection socket for connection cable to OnlinePro C: Connection for optional operating headset D: GPS antenna connection E: GSM antenna connection F: Velcro strip for attachment A B F F C D E Side view, left GSM/GPS Box Side view, right The GSM/GPS Box can be installed in the glove compartment, for example. However, an installation position allowing a maximum possible distance from the Online Pro should be selected. On the housing of the GSM/GPS Box, there are two Velcro strips F for attachment. Install the lead in such a manner that it cannot be pinched, bent or pulled out. The GSM/GPS Box should be installed in such a way that the SIM card inserted into the SIM card holder can be taken out without having to remove the GSM/GPS Box. Subject to errors or technical changes 40 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide Inserting the SIM card In order to insert the SIM card received from your network operator/ provider, the retaining cover A must be opened. If the SIM card was delivered in "credit card" format, please detach the small section of the card. The SIM card holder is found under the retaining cover A. Push the top side of the SIM card holder in the direction of the arrow. Now lift up on the released SIM card insertion slot. Slide the SIM card with the connectors into the raised SIM card insertion slot. The slanted corner of the SIM card must face toward the edge of the housing. Subsequently, press the SIM card insertion slot back down and push in the opposite direction of the arrow. Close the retaining cover A. Position of the SIM card in the holder A GSM/GPS Box ) Older SIM cards (5 Volt technology) cannot be used. Please consult your network provider. Subject to errors and technical changes 41 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide Connecting the leads · Insert the connecting cable into socket B of the GSM/GPS Box and connect the other end of the cable to the appropriate connection on the OnlinePro. Connect the additional earth lead to the lug intended for this purpose on the Online Pro Connect the GSM/GPS antenna plugs to the sockets D and E on the GSM/GPS Box. Connect the optional telephone handset (if available) to socket C of the GSM/GPS Box. · · · Additional earth lead Subject to errors or technical changes 42 Copyright by Becker GmbH, D-76303 Karlsbad Installation Guide 8. Connection of the reverse signal If the switch on the gearbox or shift linkage is accessible: · Connect a separate lead to the activated contact. Connect lead to socket A, pin 2. Low - level = earth, high - level 12 V - 16 V A If the switch is not accessible: · Check which lead is routed to the reversing lamp. Then, if necessary, remove the inner cover for the reversing light. Connect a separate lead to the active lead of the reversing lamp and connect with socket A, pin 2. Reverse signal 9. Connection of the speed signal (GAL) from the speedometer/ tachometer Electronic speedometer · Remove the signal from the speedometer, extend and connect to socket A pin 1. ) · Depending on the vehicle equ ...