The U.S. Robotics 4-Port Broadband Router can easily be connected to any Ethernet-based cable modem or DSL modem, or an RS-232 based analogue or ISDN modem. You can verify compatibility by checking to see if your cable or DSL modem is connected to the network adapter in your computer using an Ethernet cable. Connect your 4-Port Broadband Router to your computer and power supply 4-Port Broadband Router 4-Port Broadband Router Broadband Router Quick Installation Guide Package Contents Connecting the 4-Port Broadband Router one (1) Ethernet cable Note: For the most updated information, visit: http://www.usr.com/suppor t http://www.usr.com/support .usr.com/suppor You can also refer to the User Guide on the U.S. Robotics Installation CD-ROM for more detailed information. cable or DSL modem 4-Port Broadband Router 5VDC power supply Quick Installation Guide Installation CD-ROM Prepare for installation Note: Your product number is 8000-02. It is very important that you have your serial number written down before you install the 4-Port Broadband Router. You can find your serial number on the bottom label of the 4-Port Broadband Router and on the side of the package. If you ever need to call our Technical Support department, you will need this number to receive assistance. Connect one end of an Ethernet cable to your PC's Ethernet adapter. Connect the other end to one of the LAN ports on the 4-Port Broadband Router. analogue or ISDN modem What You Need to Begin · · · · · PC with an Ethernet adapter (NIC) installed A functioning Ethernet-based cable or DSL modem OR an RS-232 based analogue or ISDN modem Operating System installation CD-ROM Internet Explorer 4 or later OR Netscape 4 or later If you have an analogue or ISDN modem, an RS-232 cable Ethernet adapter (NIC) Ethernet adapter (NIC) 4-Port Broadband Router Note: Be sure to find out what letter your CD-ROM drive uses before you begin installing your new product. You will need to know this to properly install your software. 4-Port Broadband Router Product Number Front View LEDS L AN LINK/ACT Green - Blinking Green - Lighted L AN 10/100 Green - Off Green - Lighted WAN LINK Green - Blinking Green - Lighted WAN 10/100 Green - Off SYSTEM WAN STATUS POWER Orange - Blinking Orange - Lighted Orange - Lighted 10 Mbps WAN link is achieved 4-Port Broadband Router is functioning properly WAN connection established and in use Receiving power Sending or receiving WAN data 100 Mbps WAN link is achieved 10 Mbps LAN link is achieved WAN Ethernet signal detected Sending or receiving LAN data 100 Mbps LAN link is achieved Serial Number 8000-02 Color - Action Green - Lighted LAN Ethernet signal detected Function Note: During the Installation procedure, you may be prompted for your Windows Operating System CD-ROM. Make sure you have that available in case you need it. cable or DSL modem Turn on your cable, DSL, analogue, or ISDN modem. Connect the included power cord to the power jack on the 4-Port Broadband Router. Plug the power cord into a standard power outlet. Turn on your PC. analogue or ISDN modem Connect your modem to the 4-Port Broadband Router 4-Port Broadband Router Configure the basic connection settings Note for Windows Me and XP users: Universal Plug and Play may launch during the configuration step. If Universal Plug and Play does launch, follow the onscreen instructions accordingly. If Universal Plug and Play does not launch, follow the procedures below. Cable or DSL modem users: · Turn off your PC and your cable or DSL modem. · Locate the Ethernet cable that connects your cable or DSL modem to your PC's Ethernet adapter. · Disconnect that Ethernet cable from your PC's Ethernet adapter, and connect it to the WAN port on the rear of the 4-Port Broadband Router. cable or DSL modem Launch a Web browser. In the location or address line of your Web browser, type http://192.168.123.254 to access the Configuration Utility. There is no default password for the 4-Port Broadband Router, so just click Login Click P rimar y Setup Change and ogin. rimary Setup Change, etup, then select your WAN type. Depending on your WAN type, you may need to supply some connection information. When you are finished, click Save Save. 4-Port Broadband Router Rear View Port Printer COM WAN L AN ports 1-4 Function To attach a printer to the Local Area Network To connect an analogue or ISDN modem RJ-45 port to connect a broadband modem To connect devices to the Local Area Network Analogue or ISDN modem users: · Turn off your PC and your analogue or ISDN modem. · Locate the serial modem cable from your analogue or ISDN modem that is connected to your PC's serial port. · Disconnect that serial modem cable from your PC's serial port, and connect it to the COM port on the 4Port Broadband Router. analogue or ISDN modem Note: Refer to the "Configuring the 4-Port Broadband Router" section in the User Guide for more detailed configuration information. Contact your ISP if you have any questions about your WAN type or your connection information. Congratulations! The installation procedure is now complete. Cable or DSL users: You should now have secure and shared Internet access. To verify your connection, launch a Web browser and register your product at www.usr.com/ www.usr .usr.com/ prdouctreg If the page loads, you are finished with the installation procedure. If the page does not load, proceed to the Troubleshooting section in the User Guide on the U.S. Robotics Installation CD-ROM. Analogue or ISDN users: You should now have secure and shared Internet access. Click Connect in the Status page to initiate a dial-up session with your ISP. The Status page will indicate whether or not the call was successful. If the settings are correct, the analogue or ISDN modem can be used to connect to the Internet. If the connection fails, verify that you entered the correct values. For troubleshooting, technical support, and regulatory information, refer to the other side of this guide. For additional troubleshooting information, refer to the User Guide on the U.S. Robotics Installation CD-ROM. Side Panel 5VDC Power supply connection port Unplug the power supply. Press in and hold the RESET button. While holding the RESET button, plug in the power supply. When the 4-Port Broadband Router has power again, continue to hold the RESET button until the SYSTE M LED begins flashing. This will reset the 4-Port Broadband Router to the factory default settings. Reset Note: If your cable, DSL, analogue, or ISDN modem is connected to your PC using a USB cable, disconnect the USB cable from both your PC and from your modem. ...