User manual ASKO 1895 - INSTALLATION INSTRUCTIONS

ASKO DISHWASHER INSTALLATION INSTRUCTIONS T! s PORTANese instructionsher. IM th a f w ll o he dish Read a talling t ins before UTOMA OMATIC LOOP AUTOMATIC HIGH LOOP drain fastened T he dr ain hose is f astened to the back of the machine at the best eliminate high loop height. To eliminate drain prob lems, leav oblems potential dr ain pr ob lems , leave this hose in place. CONTENTS Introduction What You Need Dimensions Preparing the Location Hot Water Supply Drain Supply Electrical Connections Preparing the Dishwasher for Installation Moving the Machine into Place Connecting the Electric Cable Connecting the Water Supply Adjusting the Leveling Legs Fastening the Dishwasher to the Cabinet Replacing the Toe Kick Brackets Installing the Toe Kick Changing the Front Panels Fitting the 1805FI Custom Door Panel Fitting the Semi-integrated Custom Door Panel on Model 1895 2 2 3 3 4 5 6 6 7 7 8 8 8 9 9 9 10 12 SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE Page 1 INTRODUCTION Read these instructions carefully and completely before you install the machine. The installation should be carried out by a qualified person who is familiar with all local codes and ordinances for electrical and plumbing connections. If a dishwasher is being installed in this area for the first time, most of the cabinet work, plumbing, and electrical has to be done before you move the machine into place. If you are replacing an old dishwasher, you must check the plumbing connection and wiring before you move the new dishwasher into place. NOTE: Cosmetic damage must be reported to the ASKO dealer within five days from the date of purchase. After unpacking the dishwasher, thoroughly check the unit for cosmetic damage. WHAT WHAT YOU NEED TOOLS 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) Phillips No. 2 screwdriver Flat blade screwdriver Torx screwdriver size T 20 Adjustable wrenches (if you use copper fittings) Open-ended wrench (1/2" [12 mm] or 5/8" [16 mm]) Wire cutters and strippers Tape measure Spirit level Electric drill with 1" drill bit Keyhole saw 1) 2) 3) 4) 5) 6) 7) 8) MATERIALS MATERIALS Minimum 3/8" OD copper tubing of sufficient length 9) for your installation Shut-off valve and fittings for water supply line 1 compression nut 1 compression sleeve 1 90° street elbow 1 90° compression elbow, 3/8" (10 mm) OD 10) Tip Guards (optional) When it is not possible to attach the dishwasher to the cabinet, you should install tip guards to prevent the machine from tipping when you open the door. Refer to page 3 for installation instructions. Tip Guards (P/N 8070851) DA TECHNICAL DATA Water pressure Power Heating element Max loading 18-176 psi 120 v, 60 Hz, 15 amp. 1400 w 1650 w Page 2 DIMENSIONS UNIT DIMENSIONS US Measure Height Width Depth Weight 32-1/4"­35-1/2" 24" 22-7/16" 104 lb CABINET OPENING European Measure 825­900 mm 610 mm 570 mm 48 kg Height Width* Depth US Measure 32-1/4"­35-1/2" 24" 22-7/16" European Measure 825­900 mm 610 mm 570 mm * Models 1805 FI and 1895 do not have fill strips. The width for these models is 23-1/2" (596 mm). PREPARING LOCA OCATION PREPARING THE LOCATION The best place for your dishwasher is in the kitchen near the sink. This makes it easier to connect the water and drain supply lines. A built-in dishwasher must be enclosed on the top, both sides and the back. machine, a maximum of 2" from the back wall and 7" to 9" from the floor, depending on the underneath cabinet height. Access holes must be round and smooth, and they must be no bigger than 1-1/2" in diameter. Under-Counter Space Needed INSTALLING GUARDS INSTALLING THE TIP GUARDS (OPTIONAL) When it is not possible to fasten the dishwasher to the cabinet, you should install tip guards to prevent the machine from tipping when the door is opened. The tip guards can be attached either to the floor or the wall. The tip guards should be mounted behind the machine, 19" apart (measuring center to center) and 18-1/2" from the front of the machine. (Note: This measurement could vary, depending on the thickness of the custom panel, if any.) The kick plate supplied with your dishwasher will fit a 24" opening. When using European standard installation, a kick plate is available from your ASKO dealer. (Part Numbers: White=8057528-0; Black=8057528-29) The electrical and water supplies should enter through the area indicated by the shading on the illustration above. They should come through the right side of the Rear Tip Guards (P/N 8070851) We recommend that you install tip guards when it isn't possible to fasten the dishwasher to the cabinet. Page 3 INSTALLA ALLATION CORNER INSTALLATION If the dishwasher is installed in a corner, there must be a minimum clearance of 2 inches (50 mm) from the side wall so the door can open. 2" clearance HOT W ATER SUPPLY HOT SUPPLY WARNING! Plumbing connections must comply with applicable sanitary, safety and plumbing codes in your area. The machine should preferably be connected to a hot water supply. If a cold water supply is used, the washing times will be longer but the performance will not be affected. The hot water supply line should be minimum 3/8" OD copper tubing. The inlet valve has a 3/8" NPT female connection. After determining where the water supply line will enter the dishwasher, drill a 1" access hole and run the line to the approximate inlet valve location shown in the figure below. The inlet valve is on the right front of the machine, so the water line should be placed on the right side. If you use soft copper line, leave the tube straight out in the opening to slide the dishwasher in. Bend the tube into position after the dishwasher is slid into the cabinet opening. For service convenience, a shut-off valve (not supplied) should be installed in the supply line in an easily accessible location (such as, beneath the sink) or in the supply line near the dishwasher fill valve. It is important that the water supply line and the shut-off valve have a sufficient flow volume. At last 3 gallons (12 liters) per minute must be able to pass through the line. The water pressure should be 18-176 psi. CONNECTIONS Compression sleeve Compression nut 3/8" OD copper water line WARNING! In order to prevent heat damage to the inlet valve, all solder connections must be made before the water line is connected to the dishwasher. Inlet valve, 3/8" OD INSTALLA ALLATION INSTALLATION 90° compression elbow 3/8" NPT one end 90° street elbow (1) Hot water supply (2) Shut-off valve (not supplied) (3) Alternate locations (4) & (5) Tubing NOTE: You should only install the number 4 tubing before you push the machine into position. Tubing number 5 is to be fitted when the machine is in position. Page 4 SUPPLY DRAIN SUPPLY ASKO provides a 7/8" drain hose which is connected to the back of the unit to form a high loop. If additional drain hose is needed, please purchase an additional ASKO drain hose and joint it to the provided hose with a 7/8" copper tube. INSTALL THREE W AYS TO INSTALL DRAIN CONNECTIONS A.) Typical connection to sink plumbing before trap (high loop drain) NOTE: Do not use any fittings anywhere in the drain line that are less than 7/8" ID. The access hole for the drain line should be 1-1/2". The end of the drain line is 1/2", but it is adjustable to 7/8", 3/4", 5/8". If the drain connection is larger than 1/2", you can easily cut the drain line to fit the connection. The illustrations to the right show three ways to connect the drain supply line. LOOP THE HIGH LOOP All ASKO dishwashers have drain hoses attached to the drain pump and fastened to the top back of the unit. This gives the drain hose an automatic high loop, which is necessary for proper draining. The drain hose is fastened at the best high loop height with a plastic zip tie. To eliminate potential drain problems, simply leave this hose in place. B.) Connection to air gap then to the trap IMPORT IMPORTANT THINGS TO REMEMBER: Failure to provide the proper drain connection height (minimum of 20" above the bottom of the dishwasher base) or a 20" high loop will result in improper drainage, which will damage the machine. No part of the drain hose should be higher than 35" from the bottom of the dishwasher. The hose must not be drawn straight to a floor well or its equivalent because it might function as a siphon and empty the machine. The drain hose can be extended to a maximum length of 10 feet. Joints and jointed tubes, if any, must have a minimum 7/8" ID. C.) Connection to waste disposer with air gap If the drain line is going to be connected to a waste disposer, be sure to remove the knockout or plug from the fitting on the disposer before connecting the drain line. Do not use fittings smaller than 7/8"; otherwise the water may not drain properly. When the installation is ready, open the supply valve and let the pressure act for a while. Then check that all connections are tight and there are no leaks. NOTE: Don't forget to remove the knockout or plug from the disposer fitting. Page 5 ELECTRICAL CONNECTIONS WARNING! Before working on wiring for any electrical appliance, be sure the electrical power has been turned off at the breaker/fuse box. WARNING! Disconnect electrical power supply and place a tag at the disconnect switch indicating that you are working on the circuit. WARNING! Electrical and grounding connections must comply with the applicable portions of the national electrical code and/or other local electrical codes. The electrical supply must be a 110­120 volts, 15 or 20 amp properly grounded circuit. No other appliance or outlets should be on this circuit. NOTE: Access holes must not be larger than 1-1/2" in diameter with no sharp edges. GROUNDING INSTRUCTIONS GROUNDING INSTRUCTIONS This unit must be grounded to operate properly. It must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead of the appliance. Damage to the dishwasher could occur if it is not properly grounded. WARNING! Make sure the water supply line, drain line and branch circuit wiring do not touch any exposed terminals of dishwasher wiring. PREPARING DISHWASHER INSTALLA ALLATION PREPARING THE DISHW ASHER FOR INSTALLATION At this point the styrofoam, plastic wrap, and the wood pallet (base) should be removed from the dishwasher. Now is an excellent time to inspect for any shipping damage. Should you find any damage, you should report it to your dealer or builder immediately. Be sure to remove the toe kick and toe kick insulation which are wrapped in heavy brown paper and packed inside the dishwasher. SLIDES FOR REAR LEGS The unit comes with two white plastic slides for the rear legs to protect the kitchen floor from being damaged when you slide the unit into place. The slides simply snap onto the bottom of the rear legs. Protective slides for rear legs simply snap onto the bottom of the legs. THE FILL STRIPS All ASKO dishwashers (except Models 1805FI and 1895) have color-coded fill strips to finish off the installation. To prevent damage to the machine, be sure to remove the shipping screws that secure the fill strips to the access panel. These screws are to be thrown away. Do not replace them into the access panel. REMOVING PANEL REMOVING THE ACCESS PANEL To remove the access panel, first remove the two screws on each side of the access panel. There are two tabs at the top of the access panel that hold the panel in place against the guard plate. To remove the panel, you must slide it down below these tabs. REMOVING REMOVING THE TOE KICK BRACKETS BRACKETS WARNING! Do not screw the fill strips back to the lower access panel; otherwise, the machine will have to be uninstalled if service is necessary. Fill Strip Toe kick bracket To remove the toe kick brackets, hold the small metal spring tab on the outer edge of the base pan toward the outside of the machine. Continue holding the tab as you pull straight out on the bracket. (Note: It may be stubborn because it's in guide slots on the base pan.) Access Panel NOTE: If the cabinet opening is European measurement (23-1/2 inches [600 mm]), remove the fill strips to fit the dishwasher into the opening. Page 6 REMOVING GUARD PLATE REMOVING THE GUARD PLATE There are four screws that hold the guard plate in place, two on the upper/underneath side and two on the front. To remove the guard plate, first remove the toe kick brackets (see page 6). Then remove the two screws on the upper/underneath side of the guard plate. Next, remove the two screws from the front side of the guard plate. Guard plate After the screws are removed, grip the bottom of the guard plate and pull it toward you to remove it. You can now access the inlet valve, electrical connection, and drain pump and hose, as illustrated below. Remove the two screws on each side of the guard plate. Remove the two screws on each side of the guard plate. MOVING MACHINE INTO PLACE MOVING THE MACHINE INTO PLACE 1. 2. 3. 4. Position the machine in front of the cabinet opening. Make the height adjustment while the dishwasher is in front of the opening. Pull out the drain hose to ensure there are no sharp bends. On the bottom rear of the dishwasher there is a black ziptie around the rubber buffer that holds the circulation pump in place. Cut the ziptie and remove it. Start to feed water, electric, and drain lines into position. Make sure you've put the protective slides on the rear legs to prevent damaging the floor when you slide the unit into place (see page 6). Gently slide the unit into the dishwasher opening. As you do this, feed the drain line into the drain line hole. Also, feed the electrical and water lines to the 5. 6. 7. As you slide the unit into place, feed the drain line into the drain line hole and the electrical and water lines to the right front of the dishwasher. WARNING! Be careful of sharp edges. CONNECTING THE ELECTRIC CABLE WARNING! Before starting this procedure, be sure 3. Connect branch circuit black lead to brown lead on main terminal block. Connect ground wire to ground on terminal block. 1. Connect supply cable with a UL-listed strain relief bushing (if nonmetallic cable is to be used). Connect branch circuit white lead to white lead on main terminal block. 4. 2. Page 7 SUPPLY CONNECTING THE W ATER SUPPLY In order to prevent heat damage to the inlet valve, all solder connections must be made before the water line is connected to the dishwasher. Flush the water supply line prior to connecting it to the inlet valve of the machine. The unit has a float switch in the base pan to protect against flooding. If the inlet valve connection is not seated properly, water may leak into the base pan and activate the float switch. Make sure the connection is seated and not leaking before completing the installation. It is important that the water supply line and the shut-off valve have a sufficient flow volume. At last 3 gallons (12 liters) per minute must be able to pass through the line. The water pressure should be 18-176 psi. If the water line is installed properly, there is no need to seal the connection with TeflonTM tape. Bend the tube into position after the dishwasher is in the cabinet opening. It's best to use a tube bender to keep the line from kinking. (1) Hot water supply (2) Shut-off valve (3) Alternate locations (4) & (5) Tubing NOTE: You should only install the number 4 tubing before you push the machine into position. Tubing number 5 is to be fitted when the machine is in position. TESTING FOR LEAKS 1. Turn on the water supply and check for leaks. 2. Turn the power on at breaker/fuse box and test the dishwasher operation by running a Rinse cycle. (This should take about four minutes.) 3. Turn off the electrical power and check for leaks under the dishwasher. 4. Make sure that no kinks have developed in the drain lines. If there are no leaks and the dishwasher seems to be working properly, continue with the installation. ADJUSTING THE LEVELING LEGS Now that all the connections are made and the machine is in place under the cabinet, you should make the final height adjustment. 1. Using a 1/2" (12 mm) wrench, adjust the locking nuts until the machine is level. (The machine may have an inclination of 2° maximum without affecting its performance.) 2. When the feet are properly adjusted, tighten the locking nuts to the base pan. NOTE: When adjusting the unit lower than 33-1/4" the toe kick has to be modified; the holes for the access panel and fill strips need to be elongated. FASTENING THE DISHWASHER TO THE CABINET It's necessary to fasten the dishwasher to the cabinet so it won't tilt when the door is opened or if something heavy is placed on the door. Use only the stainless steel screws provided with the machine. 1. Use option A for U.S. or European standard installations. Use option B only for European standard installations. 2. Cover the screw heads with the plastic plugs provided with the machine. 3. When the machine is properly attached, check that the feet are tight against the floor and that the machine is level. NOTE: When it is not possible to attach the dishwasher to the cabinet, you should install tip guards. (See "Tip Guards" on page 2.) NOTE: Option A can be used for U.S. or European installations. Use option B for European standard installations only. Page 8 REPLACING BRACKETS REPLACING THE T OE KICK BRACKETS After you replace the guard plate (see page 7), you need to replace the toe kick brackets. While holding the spring tab on the base pan toward the outside of the machine, slide the bracket into the slots on the guard plate and work it between the guide slots on Guard plate the base pan. Adjusting the Bracket Depth You will have to adjust the bracket depth to allow for the thickness of the toe kick. To do this, first measure the thickness of the toe kick. Then press the spring tab on the sides of the base pan toward the outside of the machine and carefully pull or push the bracket to the required depth less the thickness of the toe kick. NOTE: Make sure the toe kick bracket is securely inside the guides on the base pan. INSTALLING INSTALLING THE TOE KICK Once you have the toe kick bracket in place, you can install the toe kick, as follows: 1. 2. 3. If you have not done so, remove the toe kick and felt insulation from the brown paper packaging. Lay the insulation on the back side of the toe kick to make sure it fits properly. Peel the adhesive protection strip off the insulation and press it firmly to the back side of the toe kick, making sure you don't cover any slots on the toe kick. Positioning the notches on the toe kick at the edge of the access panel, slide the toe kick up behind the access panel then let it slide to the floor. Screw the toe kick to the toe kick brackets. Adjusting the Height on Models 1805FI and 1895 These models come with two toe kicks. Use the mounted toe kick if the machine will be 32-1/2" to 33-1/2" high. If it will be higher, use the toe kick packed inside the dishwasher. The toe kick has extended screw slots that allow you to adjust the height. Position the toe kick so it touches the floor and tighten the screws. Extended screw slots 4. 5. CHANGING THE FR ONT PANELS FRONT PANELS WARNING! Before working on any electrical appliance, be sure the electrical power has been turned off at the breaker/fuse box. Refer to the illustration at right for instruction references. 1. 2. Remove the lower access panel with standard or 20 torx screwdriver. Using needlenose pliers, remove the plastic plugs around the edges of the access panel and upper door panel. You may discard the plugs. Using the screws provided with the trim kit, loosely secure parts A and C to the upper door panel. Slide the upper panel into the trim kit grooves. Tighten the screws holding parts A and C. Secure part B and tighten screws. Loosely screw part E to the lower access panel. Slide the custom panel into trim kit channels and tighten the screw to part E. Secure part D of the trim kit and tighten the screws. After you install the front panels, you should test the door before you push the dishwasher into the cabinet opening. If the door doesn't open properly, you may need to adjust the door springs (see page 10). NOTE: The stainless steel panels do not have holes for custom trim. You have to drill the holes. Panel Trim Kit 3. 4. 5. 6. 7. 8. 9. 10. Secure the lower access panel to the dishwasher. 11. Drop the access panel to line up with the lower holes on the guard plate. Page 9 CUSTOM PANEL FITTING THE 1805FI CUSTOM DOOR PANEL The 1805FI can only be installed with a custom door panel that extends from the toe kick to the counter top. The unit comes with everything needed to make installing the door panel easy. The door is predrilled for the panel's mounting screws. The custom panel should be at least 1/4" thick. CUSTOM PANEL CUSTOM PANEL DIMENSIONS Width: Height: 23-3/8" (597 mm) 28-1/8"­30-1/8" (714 mm­765 mm) (Measured from the top of the panel to the lower edge of the kitchen cabinet.) 1/4" (25 mm) Up to 22 lb. ITEMS PROVIDED WITH THE UNIT PRO Two 3/8" screws (B) One protective tape (C) Four adhesive-backed plastic spacer washers (D) Four 1-3/4" screws (G) Thickness: Weight: NOTE: Specifications subject to change without notice. NOTE: Heavy-duty door springs can be purchased for wooden door panels weighing over twelve pounds. (P/N 8071323-77). INSTALLING CUSTOM PANEL INSTALLING THE CUSTOM PANEL Before fitting the custom panel, the dishwasher must be installed underneath the cabinet. After you've made the required measurements, pull the machine out again to install the panel. Refer to the illustration at right for instruction references. 1. Fit the handle (A) onto the panel according to the manufacturer's instructions. (NOTE: A handle should be used rather than a knob, because a knob does not provide enough grip.) 2. Peel the adhesive backing off the washers and place them in line with the four keyholes (C) on the metal front of the dishwasher door. 3. Loosen the screws (D) on the outer edges of the dishwasher door. 4. Pull the turbo fan exhaust frame (E) down until the lower edge aligns with the lower edge of the cabinets and tighten the screws. Next, snap the plastic duct into the turbo fan exhaust vent. Installing the 1805FI Custom Panel WARNING! The custom panel must not obstruct the turbo fan exhaust. See step 4 above for instructions on how to adjust the fan exhaust. 5. The two short screws (B) go into the back of the panel, 16-3/16" from the upper edge of the panel and 5/8" from the outer edges. Insert the short screws into the panel, leaving 1/8" of space between the screw head and the panel. 6. Hook the panel screws (F) into the keyholes (C) on the dishwasher door. 7. Push the panel upwards until the lower edge aligns with the lower edge of the cabinets. ADJUSTING THE DOOR SPRINGS After you install the custom panel, make sure the door can be opened at any angle. If it tends to fall down, pull out the machine and tension the door springs on the sides of the machine by moving them one hole farther back or by twisting the spring to make it shorter. If that doesn't resolve the problem, you may need to purchase the heavy-duty door springs (Part Number 8071323-77). NOTE: The custom panel should not extend more than 2-15/16" below the bottom of the dishwasher door. Otherwise, it will strike the toe kick and damage the machine and/or the panel. 8. Open the door and tighten the screws (F) inside. 9. Remove the backing from the protective tape and apply it on the bottom edge of the panel, in front of the exhaust vent. Page 10 FASTENING THE DISHWASHER TO THE CABINET Refer to page 8. CUSTOM PANEL INSTALLA ALLATION 1805FI CUSTOM PANEL INSTALLATION OPTIONS 4-inch Kick Installations 4-inc h Toe Kic k Installa tions Custom panels the same height as the dishwasher door If the custom panel is the same height as the dishwasher door, a 2" decorative fill strip or pull-out cutting board must be used to fill the area between the panel and the counter top (as illustrated below). A 2" decorative fill strip or cutting board is required when the door panel is the same height as the dishwasher door. A 2" support strip hides the top of the dishwasher and further reduces water noise. If you install the door panel to reach the cabinet top, we recommend that you install a 2" support strip between the upper edge of the dishwasher and the counter to hide the top of the dishwasher and further reduce water noise. 6-inch Kick Installations 6-inc h Toe Kic k Installa tions For 6" toe kick installations, the decorative fill strips or support strips are unnecessary. Custom panels that extend to cabinet top Another installation option for a 4" toe kick is to extend the custom panel to the cabinet top (as illustrated below), which eliminates the need for a decorative fill strip. Panel extends from toe kick to cabinet top. 28-1/8" (714 mm) 23-1/2" (596 mm) 6" (150 mm) 23-5/8" (599 mm) 30-1/8" (765 mm) 23-1/2" (596 mm) 4" (100 mm) No fill strips or support strips are necessary with a 6" toe kick. 23-5/8" (599 mm) With this installation, the door panel extends 2" above the dishwasher control panel, as illustrated. This makes setting the controls slightly less convenient, but the aesthetic benefits seem to outweigh this small disadvantage. 2" (50 mm) Page 11 SEMI-INTEGRATED CUSTOM FITTING THE SEMI-INTEGRATED CUST OM DOOR PANEL ON MODEL 1895 Model 1895 was designed to easily accommodate custom panels. If you use the 4" toe kick, a 2" filler strip or a pullout cutting board above the unit will be necessary. The opening width for Model 1895 is 23-5/8" (600 mm), which is 3/8" narrower than standard domestic dishwashers. PANEL W OODEN PANEL DIMENSIONS Width: Height: Thickness: Weight: 23-3/8" (594 mm) 22-9/16"­24" (573 mm­609 mm) 3/4" (19 mm) (to be flush with the control panel) Up to 22 lbs. PRO ITEMS PROVIDED WITH THE UNIT Two short screws (D) Four long screws (E) Four adhesive-backed plastic spacer washers (D) One protective tape NOTE: Specifications subject to change without notice. NOTE: Heavy-duty door springs can be purchased for wooden door panels weighing over twelve pounds. (P/N 8071323-77). INSTALLING PANEL INSTALLING THE PANEL Before fitting the custom panel, the dishwasher must be installed underneath the cabinet. After you've made the required measurements, pull the machine out again to install the panel. Refer to the illustration at right for instruction references. 1. Loosen the screws (A) on the outer edges of the dishwasher door. 2. Pull the turbo fan exhaust frame (B) down until the lower edge aligns with the lower edge of the cabinets and tighten the screws (A). Next, snap the plastic duct securely into the turbo fan exhaust vent. Installing the 1895 Custom Panel WARNING! The custom panel must not obstruct the turbo fan exhaust. See step 2 above for instructions on how to adjust the fan exhaust. 3. The spacers (C) between the control panel and the custom door panel allow you to accommodate the height of the custom panel (from 1" up to 1-7/16"). To remove a spacer, loosen the nuts at the bottom of the spacers and remove as many as necessary. Screw the nuts back on and cut off any protruding parts of the plastic screws. (If necessary, you can omit the spacers.) 4. To mark where to put the two short screws (E), hold the custom panel in place against the front of the dishwasher door and measure 16-1/8" from the top of the dishwasher, marking that distance on both sides of the custom panel. Next, measure 5/8" from the edges and mark that across the first measurement. 5. Insert the short screws (E) into the back of the wooden panel where you marked, leaving 1/8" of space between the screw heads and the panel. 6. Insert the screw heads (E) into the lower part of the keyholes (D) and push the panel upward until the door aligns with the cabinets. 7. Holding the custom panel in place, open the dishwasher door and tighten the four screws (F) that secure the panel. ADJUSTING THE DOOR SPRINGS After you install the custom panel, make sure the door can be opened at any angle. If it tends to fall down, pull out the machine and tension the door springs on the sides of the machine by moving them one hole farther back or by twisting the spring to make it shorter. If that doesn't resolve the problem, you may need to purchase the heavy-duty door springs (Part Number 8071323-77). FASTENING THE DISHWASHER TO THE CABINET Refer to page 8. Page 12