Installation Instructions Undercounter Dishwasher (Plastic Giant Tub Models) Instructions d'installation Lave-vaisselle encastré (modèles à très grande cuve en plastique) Table of Contents.............................................................................2 Table des matières .........................................................................17 8575348 Table of Contents Dishwasher Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Tools and parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Location Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Drain Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Water Supply Requirements . . . . . . . . . . . . . . . . . . . . . . 5 Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installation Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Prepare cabinet opening using existing utility hookups . . . . . . . . . . . . . . . . . . . . . 6 Prepare cabinet opening where there are no existing utility hookups. . . . . . . . . . 7 Prepare dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Make electrical connection . . . . . . . . . . . . . . . . . . . . . . . 11 Connect to water supply . . . . . . . . . . . . . . . . . . . . . . . . 12 Connect to drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Secure dishwasher in cabinet opening. . . . . . . . . . . . . 13 Dishwasher Safety Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING." These words mean: DANGER WARNING You can be killed or seriously injured if you don't immediately follow instructions. You can be killed or seriously injured if you don't follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. WARNING Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door. Doing so can result in serious injury or cuts. You need to: · Slowly open dishwasher door while someone grasps the rear of the dishwasher. Remove shipping materials, drain hose and lower rack. Close dishwasher door until latched. · Observe all governing codes and ordinances. · Install this dishwasher as specified in these instructions. · Installation should be performed by a qualified service technician. The dishwasher must be installed to meet all electrical and plumbing national and local codes and ordinances. 2 Installation Requirements Tools and Parts Gather the required tools and parts before starting installation. Location Requirements Do not run drain lines, water lines or electrical wiring where they can interfere with or contact dishwasher motor or legs. The location where the dishwasher will be installed must provide clearance between motor and flooring. Motor should not touch the floor. Do not install dishwasher over carpeted flooring. Protect dishwasher and water lines leading to dishwasher against freezing. Damage from freezing is not covered by the warranty. A side panel kit is available from your dealer for installing your dishwasher at the end of your cabinetry. A moisture barrier accessory (Part No. 4396277) is available from your dealer for installing underneath the countertop, but is not required. Check location where dishwasher will be installed. The location must provide: · easy access to water, electricity and drain. · convenient access for loading and unloading dishes. Corner locations require a 2" (5.1 cm) minimum clearance between the side of the dishwasher door and the wall or cabinet. · square opening for proper operation and appearance. · cabinet front perpendicular to floor. · level floor. (If floor at front of opening is not level with floor at rear of opening, shims may be needed to level dishwasher.) NOTE: To prevent shifting during dishwasher operation, shims must be securely attached to the floor. If dishwasher will be left unused for a period of time or in a location where it may be subject to freezing, have it winterized by authorized service personnel. Make sure pipes, wires and drain hose are within the shaded area shown in the "Cutout dimensions" section. Helpful Tip: If the floor in the dishwasher opening is uneven (example: tile flooring only partway into opening) you will need to take special care in measuring dimensions and in leveling dishwasher. All installations Tools needed: · pliers · Phillips screwdriver · 5/16" and 1/4" nut drivers or hex sockets · measuring tape or ruler · 10" adjustable wrench that opens to 1-1/8" (2.9 cm) · flat-blade screwdriver · utility knife · 2 twist-on wire connectors which are the proper size to connect your household wiring to 16-gauge wiring in dishwasher · small level Parts needed: · 90° elbow with 3/8" N.P .T. external threads on one end. (The other end must fit your water supply line.) · Teflon® tape or pipe joint compound · shims (if installed with built-up floor) · flashlight · shallow pan · 5/8" open-end wrench · bath towel · wood block In addition, for new installations Tools needed: · electric drill with 1/2", 3/4" and 1-1/2" hole saw bits · small tubing cutter · wire stripper · 1-1/2"-2" screw-type clamp if connecting to waste-tee Parts supplied A. 2 ­ drain hose clamps, 1 large and 1 small B. 2 ­ # 10 x 1/2" Phillips-head screws C. drain hose Parts needed: · copper tubing (3/8" recommended) or flexible stainless steel braided fill line · clamp connector or conduit connector to fit a 7/8" (2.2 cm) diameter hole A C B Make sure all these parts are included. See separate parts list for accessories available for your dishwasher. ® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company. 3 Product dimensions 25-1/4" (64.1 cm) 24-1/2" (62.2 cm) Cutout dimensions 3/4" (1.9 cm) insulation ­ may be compressed (not used on all models) 24" (61 cm)** All surfaces must be free from intrusions 33-7/8" (86 cm) min. with wheels removed 2-1/2" (6.4 cm) 6-3/4" (17.2 cm) 10-1/2" (26.7 cm) 6-1/4" (15.9 cm)*** 3" (7.6 cm) 1-3/4" (4.4 cm) 24" (61 cm) min. 34" (86.4 cm) min.* 4" (10.2 cm) 2" (5.1 cm) 21" (53.3 cm) 3" (7.6 cm) 2" (5.1 cm) 6-1/4" (15.9 cm)*** 9" (22.9 cm) SIDE VIEW 1-3/4" 4-1/4" (4.4 cm) (10.8 cm) 10" (25.4 cm) clear area 23-7/8" (60.6 cm) Cut holes in shaded area of cabinet walls or floor as specified below: water line ­ 1/2" (1.3 cm) drain line ­ 1-1/2" (3.8 cm) direct wire ­ 3/4" (1.9 cm) power supply cord ­ 1-1/2" (3.8 cm) * Measured from the lowest point on the underside of countertop. May be reduced to 33-7/8" (86 cm) by removing wheels from dishwasher. ** Minimum, measured from narrowest point of opening. *** May be increased to 6-7/8" (17.5 cm) if height of opening is 34-1/2" (87.6 cm) at its lowest point. Both sides REAR VIEW 4 Drain Requirements · Use the new drain hose supplied with your dishwasher. If this is not long enough, use a new drain hose with a maximum length of 12 feet (3.7 m) that meets all current AHAM/IAPMO test standards, is resistant to heat and detergent, and fits the 1" (2.5 cm) drain connector of the dishwasher. · Connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20" (50.8 cm) minimum above the floor. It is recommended that the drain hose either be looped up and securely fastened to the underside of the counter, or be connected to an air gap. air gap Electrical Requirements Contact a qualified electrician. Assure that the electrical installation is adequate and in conformance with all national and local codes and ordinances. You must have: · 120-volt, 60 Hz, AC-only, 15 or 20 amp., fused electrical supply. · Copper wire only. We recommend: · A time-delay fuse or circuit breaker. · A separate circuit. If direct wiring dishwasher: · Use flexible, armored or non-metallic sheathed, copper wire with grounding wire that meets the wiring requirements for your home and local codes and ordinances. · Use strain relief method provided with house wiring junction box or install a U.L.-listed/CSA-certified clamp connector to the house wiring junction box. If using conduit, use a U.L.-listed/CSA-certified conduit connector. If connecting dishwasher with a power supply cord: · Use Power Supply Cord Kit (Part No. 4317824) marked for use with dishwashers. Kit contents include: ­ Volex, Inc., UL listed 16 gauge 3 wire power supply cord with 3 prong grounded plug. ­ Neer C-500 7/8 inch strain relief. ­ 3 wire connectors. ­ Part No. 302797 grommet Follow the kit instructions for installing the power supply cord. · Power supply cord must plug into a mating three prong, grounded outlet, located in the cabinet next to the dishwasher opening. Outlet must meet all local codes and ordinances. · Use an air gap if the drain hose is connected to house plumbing lower than 20" (50.8 cm) above subfloor or floor. · Use 1/2" minimum I.D. drain line fittings. Water Supply Requirements · A hot water line with 20-120 psi (138-862 kPa) water pressure. · 120°F (49°C) water at dishwasher. · 3/8" O.D. copper tubing with compression fitting or flexible stainless steel braided fill line (1/2" minimum plastic tubing is not recommended). · A 90° elbow with 3/8" N.P external pipe threads on .T. one end. Do not solder within 6" (15.2 cm) from water inlet valve. 5 Installation Instructions WARNING Install the drain hose IMPORTANT: Always use a new drain hose even when installing a new replacement dishwasher. 1. Drill a 1-1/2" (3.8 cm) diameter hole in cabinet wall or floor on the side of the opening closest to the sink. Electrical Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher. Failure to do so can result in death or electrical shock. 2. Connect drain hose to waste tee or waste disposer using one of the following methods: · Option 1, Waste disposer ­ with air gap · Option 2, No waste disposer ­ with air gap 1. Disconnect power. 2. Turn off water supply. · Option 3, Waste disposer ­ no air gap* · Option 4, No waste disposer ­ no air gap* *an air gap is recommended Prepare cabinet opening using existing utility hookups · Follow the steps in this section if you are installing the dishwasher in an existing cabinet opening with utility hookups. · If you are installing the dishwasher in a cabinet opening that does not have hookups, follow the steps under "Prepare cabinet opening where there are no existing utility hookups" section. 1. Check that the water line reaches to the front left of opening where the water connection will be made. 2. Check that the direct wire reaches to the front right of opening where the electrical connection will be made. Helpful Tip: To reduce the vibration of the hose, keep the hose away from the floor and the edge of the hole where it passes through the cabinet. Option 1, Waste disposer ­ with air gap: 1. Remove the disposer knockout plug. Cut end of drain hose if needed (do not cut ribbed section). 2. Attach drain hose to air gap with large spring-type clamp. If the drain hose was cut, use a 1-1/2" to 2" (3.8 to 5 cm) screw-type clamp*. 3. Use a rubber hose connector* with spring or screwtype clamps* to connect air gap to disposer inlet. water line direct wire This connection must be before the drain trap and at least 20" (50.8 cm) above the floor where dishwasher will be installed. drain hose ­ cut here if needed 6" (15.2 cm) spring or screw-type clamps rubber hose connector air gap If the water line and the direct wire reach far enough into the opening, proceed to the next section "Install the drain hose. If they do not reach far enough, follow the steps " under "Prepare cabinet opening where there are no existing utility hookups. " large spring-type clamp disposer inlet drain trap drain hose 4. Insert drain hose through hole cut in cabinet to the front center of opening where drain connection will be made. drain hose * Parts available from local plumbing supply stores 6 Option 2, No waste disposer ­ with air gap: 1. Cut end of drain hose if needed (do not cut ribbed section). 2. Attach drain hose to air gap with large spring-type clamp. If the drain hose was cut, use a 1-1/2" to 2" (3.8 to 5 cm) screw-type clamp*. 3. Use a rubber hose connector* with spring or screwtype clamps* to connect air gap to waste tee. This connection must be before the drain trap and at ...