User manual CLARION VRX935VD - INSTALLATION MANUAL

English VRX935VD Installation and Wire connection manual Installation and Wire connection manual s Contents 1. 2. 3. 4. 5. 6. 7. 8. 9. BEFORE STARTING ............................................................... PACKAGE CONTENTS ........................................................... GENERAL CAUTIONS ............................................................ CAUTIONS ON INSTALLATION .............................................. INSTALLING THE MAIN UNIT ................................................. REMOVING THE MAIN UNIT .................................................. CAUTIONS ON WIRING .......................................................... WIRE CONNECTION .............................................................. SAMPLE SYSTEMS ................................................................ 65 65 66 66 67 69 69 70 73 1. BEFORE STARTING 1. This set is exclusively for use in cars with a negative ground 12 V power supply. 2. Read these instructions carefully. 3. Be sure to disconnect the battery "v" terminal before starting. This is to prevent short circuits during installation. (Figure 1) Car battery Figure 1 2. PACKAGE CONTENTS 1 Main unit 2 Tuner Amp unit 3 Manuals Owner's manual & Installation manual Warranty card Guide label for SIRIUS radio 4 Power supply lead (For the main unit) 5 Power supply lead (For the tuner amp unit) 6 Connection cord (Main unit Tuner amp unit) 7 Antenna extension cord 8 Bag for accessories of the main unit (No. 1) Flat head screw (M5 × 8) ............................ 4 Sems hexagonal bolt (M5× 8) ..................... 5 Electro tap Machine screw (M4× 3) ............................... 4 9 Bag for accessories of the main unit (No. 2) Hook plate ................................................... 2 Cord clamp Rubber cap Special screw 0 Bag for accessories of tuner amp unit Maunting bracket ......................................... 2 Canoe clip ................................................... 4 Machine screw (M4 × 8) .............................. 4 ! Universal mounting bracket @ Remote control unit # Battery (for remote control unit) $ Outer Escutcheon % DCP Case VRX935VD 65 3. GENERAL CAUTIONS 1. Do not open the case. There are no user serviceable parts inside. If you drop anything into the unit during installation, consult your dealer or an authorized CLARION service centre. 2. Use a soft, dry cloth to clean the case. Never use a rough cloth, thinner, benzine, or alcohol, etc. For tough dirt, apply a little cold or warm water to a soft cloth and wipe off the dirt gently. English Installation and Wire connection manual 4. CAUTIONS ON INSTALLATION 1. Prepare all articles necessary for installing the main unit before starting. 2. This model is used with the LCD panel slid forwards (shell loading system). On some types of cars, the LCD panel may touch the dashboard or shift lever, in which case it cannot be installed. Check that the set will not hamper operation of the shift lever before choosing the place of installation.(Figure 2) Dashboard 5. Use the enclosed screws for installation. Using other screws can cause damage. (Figure 4) Chassis Chassis Damage Max. 8 mm (M5 screw) Figure 4 6. The source unit has mounting screw holes for NISSAN (N marks) and TOYOTA (T marks) vehicles. T N T Shift lever (check that it does not touch the LCD.) Shift lever Figure 2 3. Install the unit within 30° of the horizontal plane. (Figure 3) N T N Figure 5 Max. 30° Figure 3 4. If you have to do any work on the car body, such as drilling holes, consult your car dealer beforehand. 66 VRX935VD 5. INSTALLING THE MAIN UNIT s Universal Mount 1. Place the universal mounting bracket into the instrument panel, use a screwdriver to bend each stopper of the universal mounting bracket inward, then secure the stopper as shown in Figure 6. 2. Wire as shown in Section 8. 3. Insert the main unit into the universal mounting bracket until it locks. 4. Mount the outer escutcheon so that all the hooks are locked. English Installation and Wire connection manual Notes: 1) Some car models require special mounting kits for proper installation. Consult your Clarion dealer for details. 2) Fasten the front stopper securely to prevent the main unit from coming loose. · Console opening dimensions 2-1/16" (53 mm) 7-3/16" (182 mm) Rear fastening hole (of vehicle) Instrument panel Hole Hole Stoppers Special Screw Screwdriver Rubber cap Main unit Universal mounting bracket Stoppers 2-Spring Outer escutcheon Note: Set the outer escutcheon so that its metallic part on the back side fits the upper edge of the main unit. Figure 6 VRX935VD 67 s Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles) English Installation and Wire connection manual This unit is designed for fixed installation in the dashboard. If the vehicle is equipped with a factory-installed radio, install the main unit with the parts and screws marked (). (Figure 8) If the vehicle is not equipped with a factory-installed radio, obtain an installation kit to install the main unit in the following procedure. 1. Remove the screws from both side of the main unit. Then, at either side, lift the leaf spring until the engaging claws are released from the holes, and slide the spring to the di- rection of arrow to remove it. Repeat the same for the other side to remove the springs from the both sides. (Figure 7) 2. Secure the mounting brackets to the chassis as shown in Figure 8. Holes are pre-tapped for TOYOTA and NISSAN vehicles; modification, such as drilling new holes, of the mounting brackets may be required for other models. 3. Wire as shown in Section 8. 4. Secure the unit in the dashboard, and then reassemble the dashboard and the centre panel. Engagin claw 2-Screw Main Unit 2-Spring Screwdriver Figure 7 4-Hexagonal screw (M5 × 8) Mounting bracket (1 pair for the left and right sides) Main Unit Pocket Centre Panel (Note 1) : The screws with this mark are enclosed in this set. 5: The parts and screws with this mark are used to install radio or included in the installation kit. Note 2 Figure 8 Note 1: In some cases, the centre panel may require some modification (trimming, filling, etc.). Note 2: If a hook on the installation bracket interferes with the unit, bend and flatten it with a nipper or a similar tool. 68 VRX935VD 6. REMOVING THE MAIN UNIT 1. When the rear of the main unit has been secured with the method shown in Figure 6 unfasten the special screw. 2. Remove the outer escutcheon. 3. Insert the hook plate between the spring and the universal mounting bracket, fit tab B of the spring into hole A of the hook plate, then pull the main unit out by the hook plate. (Insert both the right and left edges of the hook plate.) (Figure 9) Note: Keep the hook plate. You cannot remove the main unit without disengaging the hook plate. English Installation and Wire connection manual Universal mounting bracket 2-Hook plate Instrument panel Main Unit Spring Outer escutcheon A Figure 9 B 7. CAUTIONS ON WIRING 1. Be sure to turn the power off before wiring. 2. Be particularly careful where you route the wires. Keep them well away from the engine, and exhaust pipe, etc. Heat may damage the wires. 3. If the fuse should blow, check to see if the wiring is correct. If it is, replace the fuse with a new one with the same amperage rating as the original. 4. To replace the fuse, remove the old fuse of the power supply lead and insert the new one. (Figure10) Power supply lead for the tuner amp unit : 15A FUSE Power supply lead for the main unit : 3A FUSE Note: There are various types of fuse holder. Do not let the battery side touch other metal parts. CAUTION After the connection, fix the lead by a clamp or insulation tape for protection. Fuse Fuse holder Figure 10 VRX935VD 69 8. WIRE CONNECTION Securely connect to the metal part of the car with a screw, etc. Black Choke coil Fuse Yellow Main power supply cord English Installation and Wire connection manual Main unit Power supply lead Connection cord (provided with this unit) CeNET cable (Sold separately) VIDEO output (RCA) 5 VISUAL 1 audio input terminal L+R (RCA) VISUAL 1 video input (RCA)/ DVD changer input (RCA) TV TUNER input (RCA) & Power supply lead Reset switch Top view of the tuner amp unit 5.1ch surround decoder select switch 3 ¥ 2 $ % 6 Rear audio output (input) terminal L+R (RCA) 4 Front audio output (input) terminal L+R (RCA) 4 Non Fader output terminal L+R (RCA) 70 VRX935VD Purple/Black 2 Purple Green/Black Blue/White Green Brawn Glay Grass-green Glay/Black Orange/White White/Black Red White Yellow English 1 8 Installation and Wire connection manual 0 7 *1 3 ) 4 ! 6 @ 5 9 No. 1 2 3 4 5 6 7 8 9 0 ! @ # $ % ¥ & * ( ) ¡ Description REAR RIGHTB REAR RIGHTv FRONT RIGHTB FRONT RIGHTv FRONT LEFTB FRONT LEFTv REAR LEFTB REAR LEFTv +12 V MAIN POWER Amplifier turn-on lead ILLUMINATION +12 V ACCESSORY GROUND CCD camera VISUAL 2 terminal Radio antenna jack (2) CeNET terminal Phone mute (Brown) (1) Spare terminal (Yellow) Parking brake (Grass-Green) AUTO ANTENNA ( Black Blue # ¡ 1: Connecting the PHONE MUTE Terminal The lead included with the unit must be connected to the specified position of the vehicle's connector in order to use the "triggered audio mute for cellular telephones" function. 2: Use the attached extension lead when necessary. (Provided with this unit) Note : Before making any installation, disconnect the car battery - (negative) cable. 3: If a 5.1ch surround decoder (DVH920, sold separately) is connected and the amp of this unit is used, set the select switch to "LINE IN". Then the AUDIO OUT (IN) terminal of the Tuner Amp Unit is only available for audio input, not outputting the audio. (LINE IN) D N (LINE OUT) 4: Connect to a separately sold external amplifier with a separately sold RCA cord (L, R). Note : When the 5.1ch surround decoder is connected, these terminals are only available for audio input. 5: Connect to a Rear View Monitor (sold separately) for the rear seat. 6: Connect to separately sold VTR equipment with a separately sold connection cord. VRX935VD 71 s Connecting the Accessories · Connection to the external amplifier The external amplifier can be connected unless the 5.1ch Surround Decoder is connected. For detailed information, refer to the instruction manual of the 5.1ch Surround Decoder. English Installation and Wire connection manual · Connection to the CCD camera for vehicle The CCD camera for vehicle can be connected to CCD terminal on the tuner amp unit. For detailed information, refer to the instruction sheet or manual for the CCD camera. Notes: · A power supply box (sold separately) is required for connection of the main unit and the CCD camera. · The power supply box for camera CAA147 cannot be used. Please use the CAA188 instead. · If the specified lead of the cellular phone is connected to the phone mute lead of the source unit, the audio mute is available when the cellular telephone is used. · SIRIUS Satellite Radio When the SIRIUS is to be connected, use the CeNET connector. For detailed information, refer to the instruction manual of the SIRIUS. · TV Tunner When the TV TUNER is to be connected, connect the CeNET connector and RCA PIN (yellow). For detailed information, refer to the instruction manual of the TV TUNER. s Connecting the parking brake lead Connect the lead to parking brake lamp earth in the meter panel. Notes: · Connecting the parking brake lead to lamp earth allows you to watch TV/VTR/DVD video/video CD when the parking brake is engaged. · When the parking brake lead is not connected, the monitor will stay off. Parking brake lamp + lead to battery - cord parking brake signal lead Connect these three leads. Parking brake lead (bright green) Parking brake 72 VRX935VD 9. SAMPLE SYSTEMS s Sample System 1 MAIN UNIT VRX935VD English Installation and Wire connection manual RCA Cable (Visual) VISUAL 2 IN TUNER AMP UNIT CCA-389 Tuner IN TTX7501z (CeNET TV TUNER) VTR CeNET VISUAL 1 IN CeNET RCA Cable (Visual) RCA Cable (Visual) Rear view monitor DSH920S (SIRIUS TUNER) CeNET VCZ625 (DVD CHANGER) CeNET Mode* Front Speaker Rear Speaker CCA-519-500 *Switch the MODE switch to the CeNET mode. DCZ625 (CD CHANGER) VRX935VD 73 s Sample System 2 English MAIN UNIT VRX935VD (Gray) Installation and Wire connection manual Optical Digital Cable (included the DVH920) RCA Cable (Visual) VISUAL 2 IN TUNER AMP UNIT Tuner IN TTX7501z (CeNET TV TUNER) VTR CCA-389 CeNET VISUAL 1 IN CeNET (included the DVH920) RCA Cable (Visual) (LINE IN)D N(LINE OUT) RCA Cable (Visual) Rear view monitor Set the select switch to "(LINE IN)D". DVH920 (5.1ch surround decoder) CeNET Mode (Black) (included the SRK601) CeNET (included the VCZ625) Optical Digital Cable RCA Cable (Visual) (included the VCZ625) RCA Cable (sold separately) RCA Cable (sold separately, DCA-005/008) Front Speaker Rear Speaker Center Speaker VCZ625 (DVD CHANGER) CeNET Mode (Gray) Switch the MODE switch to the CeNET mode. SRV303 (Powered Sub Woofer) 74 VRX935VD s Sample System 3 English MAIN UNIT VRX935VD (Gray) Optical Digital Cable (included the DVH920) Installation and Wire connection manual RCA Cable (Visual) VISUAL 2 IN TUNER AMP UNIT CCA-389 Tuner IN TTX7501z (CeNET TV TUNER) VTR CeNET CeNET (included the DVH920) VISUAL 1 IN RCA Cable (Visual) RCA Cable (Visual) (LINE IN)D N(LINE OUT) Rear view monitor Set the select switch to "N(LINE OUT)". RCA cable RCA cable RCA Cable (included the SRK601) RCA Cable (sold separately) DVH920 (5.1ch surround decoder) CeNET Mode CeNET (included the VCZ625) RCA Cable (Visual) (included the VCZ625) (Black) Optical Digital Cable (sold separately, DCA-005/008) Amplifier Center Speaker VCZ625 (DVD CHANGER) CeNET Mode Switch the MODE switch to the CeNET mode. (Gray) Front Speaker Rear Speaker SRV303 (Powered Sub Woofer) VRX935VD 75 76 VRX935VD