INSTRUCTION MANUAL iV82 UHF TRANSCEIVER VHF TRANSCEIVER iU82 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IC-V82 IC-U82 FOREWORD Thank you for purchasing this Icom product. The IC-V82/U82 VHF/UHF TRANSCEIVERS are designed and built with Icom's superior technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. We want to take a couple of moments of your time to thank you for making your IC-V82/U82 your radio of choice, and hope you agree with Icom's philosophy of "technology first." Many hours of research and development went into the design of your IC-V82/U82. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL-- This instruction manual contains important operating instructions for the IC-V82/U82. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock R WARNING! may occur. CAUTION NOTE Equipment damage may occur. Recommended for optimum use. No risk of personal injury, fire or electric shock. WORD D FEATURES 7 W*-- high transmit output power (*IC-V82, 5 W for IC-U82) CTCSS and DTCS encoder/decoder standard Optional digital modulator/demodulator Optional DTMF decoder Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. i PRECAUTIONS RWARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 inches) away from the lips and the transceiver is vertical. Place the unit in a secure place to avoid inadvertent use by children. DO NOT operate the transceiver near unshielded electrical blasting caps or in an explosive atmosphere. AVOID using or placing the transceiver in direct sunlight or in areas with temperatures below ­10°C (+14°F) or above +60°C (+140°F). The use of non-Icom battery packs/chargers may impair transceiver performance and invalidate the warranty. Even when the transceiver power is OFF, a slight current still flows in the circuits. Remove the battery pack or case from the transceiver when not using it for a long time. Otherwise, the battery pack or installed rechargeable batteries (Ni-Cd: BP-222N, BP-209N, Ni-MH: BP-210N, Li-Ion: BP-211N) will become exhausted. For USA only: Caution: Changes or modifications to this transceiver, not expressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations. RWARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. Hearing experts advise against continuous high volume operation. If you experience a ringing in your ears, reduce the volume or discontinue use. NEVER connect the transceiver to a power source that is DC fused at more than 5 A. Accidental reverse connection will be protected by this fuse, but higher fuse values will not give any protection against such accidents and the transceiver will be ruined. NEVER attempt to charge alkaline or dry cell batteries. Be aware that external DC power connections will charge batteries inside the battery case. This will damage not only the battery case but also the transceiver. DO NOT push the PTT when not actually desiring to transmit. ii SUPPLIED ACCESSORIES Supplied Accessories q Antenna* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 w Belt clip (with screws) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 e AC Adapter*. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 r Battery pack*/Battery case* . . . . . . . . . . . . . . . . . . . . . . 1 t Battery charger*. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 set *Not supplied with some versions. e q w for IC-V82 for IC-U82 t r iii SAFETY TRAINING INFORMATION CAUTION To ensure that your exposure to RF electromagnetic energy is within the FCC allowable limits, always adhere to the following guidelines: · DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or an antenna specifically authorized by the manufacturer for use with this radio. · DO NOT transmit for more than 50% of total radio use time ("50% duty cycle"). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the "Tx indicator" appears. You can cause the radio to transmit by pressing the "PTT" switch. · ALWAYS use Icom authorized accessories (antennas, batteries, belt clips, speaker/mics, etc.). Use of unauthorized accessories can cause the FCC RF exposure compliance requirements to be exceeded. · ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting, and only use the Icom belt-clips which are listed in this manual when attaching the radio to your belt, etc. To provide the recipients of your transmission the best sound quality, hold the transceiver at least 5 cm (2 inches) from your mouth, and turned slightly to one side. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to assure that this radio operates within the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites. iv TABLE OF CONTENTS FOREWORD .................................................................................... i IMPORTANT..................................................................................... i EXPLICIT DEFINITIONS.................................................................. i PRECAUTIONS............................................................................... ii SUPPLIED ACCESSORIES ........................................................... iii SAFETY TRAINING INFORMATION.............................................. iv TABLE OF CONTENTS .............................................................. v­vi QUICK REFERENCE GUIDE ...................................................... I­V Preparation............................................................................... I Your first contact..................................................................... III Repeater operation ................................................................ IV Programming memory channels ............................................. V 1 ACCESSORIES...................................................................... 1­2 Accessory attachment............................................................. 1 2 PANEL DESCRIPTION .......................................................... 3­7 Switches, controls, keys and connectors ................................ 3 Function display ...................................................................... 6 3 BATTERY PACKS ................................................................ 8­12 Battery pack replacement ....................................................... 8 Battery caution ........................................................................ 9 Charging NOTE ...................................................................... 9 Battery charging .................................................................... 10 Battery case (optional for some versions) ............................ 12 4 BASIC OPERATION........................................................... 13­16 Power ON.............................................................................. 13 VFO mode selection.............................................................. 13 Setting a frequency ............................................................... 13 Setting audio/squelch level ................................................... 15 Receive and transmit ............................................................ 15 Display type........................................................................... 16 Key lock function ................................................................... 16 5 REPEATER OPERATION .................................................. 17­20 General ................................................................................. 17 Reversed duplex mode ......................................................... 17 Offset frequency .................................................................... 18 Subaudible tones .................................................................. 18 Repeater lockout ................................................................... 19 Auto repeater function (USA/CSA versions only).................. 20 6 MEMORY/CALL OPERATION ........................................... 21­26 General description ............................................................... 21 Selecting a memory channel................................................. 21 Selecting the call channel ..................................................... 21 Programming the memory/call channels ............................... 22 Channel name programming................................................. 23 Memory transfers .................................................................. 23 Memory bank selection ......................................................... 25 Memory bank setting............................................................. 25 Transferring bank contents.................................................... 26 7 DTMF MEMORY................................................................. 27­29 Programming a DTMF code sequence ................................. 27 Transmitting a DTMF code sequence ................................... 28 DTMF transmission rate ........................................................ 29 v 8 SCAN OPERATION............................................................ 30­33 Scan types ............................................................................ 30 Programmed scan................................................................. 30 Memory scan..........................................................................31 Skip channels........................................................................ 32 Priority watch......................................................................... 32 Scan resume condition.......................................................... 33 9 SUBAUDIBLE TONES ....................................................... 34­37 Tone squelch ......................................................................... 34 Pocket beep operation .......................................................... 36 Tone scan.............................................................................. 37 10 PAGER/CODE SQUELCH (Requires Optional UT-108) .. 38­41 Pager function ....................................................................... 38 Code programming ............................................................... 38 Pager operation..................................................................... 40 Code squelch ........................................................................ 41 11 DIGITAL MODE OPERATION (Requires Optional UT-118) ...............................................42­58 Digital mode operation .......................................................... 42 Call sign programming .......................................................... 42 Digital voice mode operation ................................................. 45 When receiving a digital call ................................................. 46 Break-in communication ....................................................... 47 EMR communication ............................................................. 48 Pocket beep operation .......................................................... 48 Digital squelch functions ....................................................... 49 Digital monitor ....................................................................... 49 Low-speed data communication ........................................... 50 About D-STAR system .......................................................... 51 Repeater call sign programming ........................................... 52 Setting other items ................................................................ 53 GPS operation ...................................................................... 57 12 OTHER FUNCTIONS ......................................................... 59­70 SET MODE............................................................................ 59 INITIAL SET MODE .............................................................. 63 Weather channel operation (IC-V82 [USA]/[CSA] versions only) ...................................... 69 CPU reset.............................................................................. 70 Partial reset ........................................................................... 70 13 CLONING ........................................................................... 71­72 Transceiver-to-transceiver cloning ........................................ 71 Cloning using a PC ............................................................... 72 14 OPTIONAL UNITS.............................................................. 73­74 Optional UT-108/118 installation ........................................... 73 Optional MB-86 installation ................................................... 73 15 SPECIFICATIONS .............................................................. 75­76 IC-V82 ................................................................................... 75 IC-U82................................................................................... 76 16 OPTIONS............................................................................ 77­78 17 MODE ARRANGEMENT.................................................... 79­81 18 CE ....................................................................................... 82­83 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 vi QUICK REFERENCE GUIDE Preparation D Battery pack replacement Before replacing the battery pack, push and hold [PWR] for 1 sec. to turn the power OFF. · Slide the battery release forward, then pull the battery pack upward with the transceiver facing away from you. D Charging with the BC-144N/146 The optional BC-144N provides rapid charging, and the BC146 provides regular charging of an optional battery pack with or without a transceiver attached. The following is additionally required: · An optional AC adapter. (An AD-99N is supplied with BC-144N or BC-146.) Turn power OFF. D Battery case-- optional for some versions When using a BP-208N BATTERY CASE attached to the transceiver, install 6 AA (LR6) size alkaline batteries as illustrated below. Check orientation for correct charging. (Insert together with AD-99N.) BC-144N/146 +AD-99N I QUICK REFERENCE GUIDE D About AD-99N The adapter (Spacer A) only is required for the IC-V82/U82 series. When removing the spacer (Spacer B/C), push the latch carefully with your finger to remove the spacer (Spacer B/C) from the adapter (Spacer A). Remove the spacer (Spacer B/C) from the adapter. Push the latch carefully. Attach the antenna to the transceiver as illustrated at right. R CAUTION! · DO NOT push or force the latch with a screw driver, etc., to remove it. · DO NOT bend the latch when the adapter and spacer are not joined together. This will cause weakening of the latch plastic. · Both cases may break the latch and it may not be able to be reattached. D Belt clip Conveniently attaches to your belt. Attach the belt clip with the supplied screws using a phillips screwdriver. To attach the belt clip II Quick reference guide D Antenna QUICK REFERENCE GUIDE Your first contact Now that you have your IC-V82/U82 ready, you are excited to get on the air. We would like to walk you through a few basic operational steps to make your first "On The Air" use an enjoyable experience. 2. Adjusting audio output level Rotate [VOL] to set the desired audio level. [VOL] 3. Adjusting the squelch level D About default setting YZ The [VOL] control function can be exchanged with [Y]/[Z] keys function in INITIAL SET MODE. However, in this QUICK REFERENCE, the factory default setting ([VOL] controls audio output level) is used to simplify instructions. While pushing and holding Y Z [MONI], push [Y] or [Z] to set the squelch level. MONI D Basic operation 1. Turning ON the transceiver Although you have purchased a brand new transceiver, some settings may be changed from the factory defaults because of the Quality Control process. Resetting the CPU is necessary to start from factory default. While pushing [MONI] and [D·CLR], push and hold [PWR] for 1 sec. to reset the CPU and turn power ON. MONI PWR D CLR 4. Tune the desired frequency YZ The up/down keys, [Y]/[Z], will allow you to tune to the frequency that you want to operate on. Page 14 will instruct you on how to adjust the tuning step size. Y Z Push [Y] or [Z] to adjust the frequency. III QUICK REFERENCE GUIDE Direct frequency input from the keypad is also available. To enter the desired frequency, enter 6 digits starting from the 100 MHz digit. · Entering three* to five digits then pushing [·ENT ] will also set the frequency. (*Some versions only requires two digits.) · When a digit is mistakenly input, push [D.CLR] to abort input. D CLR 1. Setting duplex Push [A·FUNC], then [4·DUP] several times to select minus duplex or plus duplex. · The USA/CSA versions have an auto repeater function, therefore, setting duplex is not required. ENT A FUNC Keypad DUP 4 · Example 1-- when entering 145.525 MHz Push TONE 1 DUP 4 SCAN 5 SCAN 5 P.BEEP 2 SCAN 5 2. Repeater tone Push [A·FUNC], then [1·TONE] several times until " " appears, if required. · Example 2-- when entering 144.800 MHz Push TONE 1 DUP 4 DUP 4 SET 8 OPT 0 ENT A FUNC TONE 1 5. Transmit and receive Push and hold [PTT] to transmit, then speak into the microphone; release to receive. IV Quick reference guide Repeater operation QUICK REFERENCE GUIDE Programming memory channels The IC-V82/U82 has a total of 207 memory channels (including 6 scan edges and 1 call channel) for storing often used operating frequency, repeater settings, etc. 3. Writing a memory channel Push [A·FUNC], then push and hold [C·MR] for 1 sec. to program. · 3 beeps sound. 1. Setting frequency In VFO mode, set the desired operating frequency with other desired settings, such as repeater and subaudible tone. C MR 2. Selecting a memory channel Push [A·FUNC] and [C·MR] then Y Z push [Y] or [Z] several times to select the desired memory channel. · "X" indicator and memory channel number blink. C MR A FUNC A FUNC · Continue to push and hold [C·MR] for 1 sec. after 3 beeps are emitted, to increment the displayed memory channel number. V ACCESSORIES Accessory attachment D Antenna Attach the antenna to the transceiver as illustrated below. 1 1 Keep the [SP/MIC] cap (SP/MIC jack cover) attached when jacks are not in use to keep the contacts clean. Attach the [SP/MIC] cap. [SP/MIC] cap 1 1 ACCESSORIES D Belt clip Conveniently attaches to your belt. Attach the belt clip with the supplied screws using a phillips screwdriver. To attach the belt clip D Handstrap (Not supplied) Slide the hand strap through the loop on the top of the rear panel as illustrated below. Facilitates carrying. 2 PANEL DESCRIPTION Switches, controls, keys and connectors q CONTROL DIAL [VOL] *Rotate to adjust the volume level. q t 2 1 2 w PTT SWITCH [PTT] Push and hold to transmit; release to receive. YZ e UP/DOWN KEYS [Y]/[Z] *Selects the operating frequency. Speaker w y Microphone e MONI PWR r KEYPAD (pgs. 4, 5) Used to enter operating frequency, the DTMF codes, etc. t ANTENNA CONNECTOR (p. 1) Connects the supplied antenna. y [SP]/[MIC] JACK Connect an optional speaker-microphone or headset, if desired. The internal microphone and speaker will not function when a connector is inserted. u FUNCTION DISPLAY (pgs. 6, 7) i SQUELCH/MONITOR SWITCH [MONI] Push and hold to force the squelch open, and set the squelch level, if required. o POWER SWITCH [PWR] Push and hold for 1 sec. to turn the power ON and OFF. YZ *The assigned function for [VOL] and [Y]/[Z] can be exchanged in INITIAL SET MODE (pgs. 14, 65). 3 u i o A FUNC B CALL C MR D CLR r TONE 1 P.BEEP 2 T.SCAN 3 BANK DUP 4 SCAN 5 SKIP 6 OPT 0 PRIO 7 SET 8 H/M/L 9 ENT !0 2 PANEL DESCRIPTION D Keypad A FUNC !0 [DATA] JACK Connect to a PC or GPS receiver via the RS-232 cable (Dsub 9 pin) for data communication in the RS-232 format. Pin 2 (RxD), Pin 3 (TxD), Pin 5 (GND) to [DATA] jack TxD GND RxD 2.5(d) mm 5 1 [A·FUNC] Access to secondary function. [B·CALL] Selects the call channel. (p. 21) [C·MR] Selects a memory mode. (p. 21) After pushing [A·FUNC], enter into memory programming/editing mode. (pgs. 22­24) After pushing [A·FUNC], programs/transfers VFO/memory or call channel contents into memory channel/VFO when pushed and held for 1 sec. (pgs. 22­24) [D·CLR] Selects VFO mode, aborts direct frequency input, or cancels scanning, etc. (pgs. 13, 30) [1·TONE] Input digit "1" during frequency input, memory channel selection, etc. (pgs. 13, 21) After pushing [A·FUNC], selects the subaudible tone function. (pgs. 17, 34) [2·P.BEEP] Input digit "2" during frequency input, memory channel selection, etc. (pgs. 13, 21) After pushing [A·FUNC], turns the pocket beep function ON and OFF. (p. 36) B CALL C MR Less than 10(d) mm 9 6 RS-232 (DB-9 female) When making the connection between your transceiver and PC or other device, ensure that the correct connections are made otherwise data communications may fail. D CLR TONE 1 P.BEEP 2 4 PANEL DESCRIPTION [3·T.SCAN] Input digit "3" during frequency input, memory channel selection, etc. (pgs. 13, 21) After pushing [A·FUNC], starts tone scanning. (pgs. 19, 37) [4·DUP] Input digit "4" during frequency input, memory channel selection, etc. (pgs. 13, 21) After pushing [A·FUNC], selects duplex function (­duplex, +duplex, simplex). (p. 17) [5·SCAN] Input digit "5" during frequency input, memory channel selection, etc. (pgs. 13, 21) After pushing [A·FUNC], starts scanning. (p. 30) [6·SKIP] Input digit "6" during frequency input, memory channel selection, etc. (pgs. 13, 21) After pushing [A·FUNC], sets and cancels skip setting for memory scan during memory mode. (p. 32) [7·PRIO] Input digit "7" during frequency input, memory channel selection, etc. (pgs. 13, 21) After pushing [A·FUNC], starts priority watch. (p. 32) [8·SET] 2 T.SCAN 3 SET 8 Input digit "8" during frequency input, memory channel selection, etc. (pgs. 13, 21) After pushing [A·FUNC], enters into SET MODE. (p. 59) [9·H/M/L] Input digit "9" during frequency input, memory channel selection, etc. (pgs. 13, 21) After pushing [A·FUNC], switches transmit power between high, middle and low output power. (p. 15) [0·OPT] Input digit "0" during frequency input, memory channel selection, etc. (pgs. 13, 21) After pushing [A·FUNC], selects an optional function mode, such as pager, code squelch or digital operation. (pgs. 40, 42) [#·BANK] After pushing [A·FUNC], enters a memory bank selection. (p. 25) [·ENT ] Sets the frequency even if the full 6 digits of frequency have not been entered. (p. 13) After pushing [A·FUNC], switches key lock function ON and OFF when pushed and held for 1 sec. Lock all keys, except [PWR], [PTT], [MONI] and audio level adjustment. (p. 16) 2 DUP 4 H/M/L 9 SCAN 5 OPT 0 SKIP 6 BANK PRIO 7 ENT 5 2 PANEL DESCRIPTION Function display q q w q e r q t q y !5 !4 u !3 !2 !1 !0 oi q FUNCTION INDICATOR Appears while a secondary function is being accessed. w KEY LOCK INDICATOR (p. 16) Appears when the key lock function is ON. e AUTO POWER OFF INDICATOR (p. 64) Appears while the auto power OFF function is activated. r DUPLEX INDICATOR (p. 17) Either "­" or "+" appears during repeater operation. t TONE INDICATOR While in the analog (FM) mode operation " " appears while the subaudible tone encoder is in use. (p. 17) " " appears while the tone (CTCSS) squelch function is in use. (p. 34) " " appears while the tone (DTCS) squelch function is in use. (p. 34) " " appears with the " " or " " indicator while the pocket beep function (CTCSS or DTCS) is in use. (p. 36) 6 PANEL DESCRIPTION While in the digital (DV) mode operation with an optional UT-118 DIGITAL UNIT installed. " " appears while the digital code (CSQL) squelch function is in use. (p. 49) " " appears while the call sign (DSQL) squelch function is in use. (p. 49) " " appears with the " " or " " indicator while the pocket beep function (CSQL or DSQL) is in use. (p. 48) y TRANSMIT INDICATOR (p. 15) Appears during transmit. u FREQUENCY READOUT Shows operating frequency, channel number or channel names, depending on display type (p. 16). i SIGNAL INDICATOR Shows receiving signal strength as below. 2 o BUSY INDICATOR Appears when a signal is being received or the squelch is open. Blinks while the monitor function is activated. (pgs. 15, 49) !0 PAGER CALL INDICATOR (p. 41) Blinks when a pager call is received. (This indicator appears only when an optional UT-108 DTMF DECODER UNIT is installed.) !1 DIGITAL MODE INDICATOR (p. 45) Appears when digital mode is selected. (This indicator appears only when an optional UT-118 DIGITAL UNIT is installed.) !2 LOW/MIDDLE POWER INDICATOR (p. 15) "L" or "M" appears when the low or middle output power is selected, respectively. No indicator appears when high output power is selected. !3 SKIP CHANNEL INDICATOR (p. 32) Appears when the selected memory channel is specified as a skip channel. !4 MEMORY MODE INDICATOR (p. 21) Appears while in memory mode or channel number indication mode. !5 MEMORY CHANNEL INDICATOR (p. 21) Shows the selected memory channel number. "C" appears when the call channel is selected. 2 Weak RX Signal level Strong Shows the output power level while transmitting. Low Middle High 7 3 BATTERY PACKS D BATTERY PACKS Battery Voltage Capacity pack BP-208N BP-209N BP-210N PWR Battery pack replacement q Before replacing the battery pack, push and hold [PWR] for 1 sec. to turn the power OFF. Battery life*1 IC-V82 --*2 IC-U82 Battery case for AA (LR6)×6 alkaline 7.2 V 7.2 V 7.4 V 7.2 V 1650 mAh 6 hrs. 1100 mAh 3 hrs. 20 min. 3 hrs. 40 min. 7 hrs. 1800 mAh 6 hrs. 10 min. 8 hrs. 15 min. 600 mAh 2 hrs. 15 min. 2 hrs. 50 min. BP-211N BP-222N Push and hold for 1 sec. w Slide the battery release forward, then pull the battery pack upward with the transceiver facing away from you. *1 Operating periods are calculated under the following conditions; Tx : Rx : standby =1 : 1 : 8, power save function: auto setting is activated *2 Operating period depends on the alkaline cells used. 8 BATTERY PACKS 3 Battery caution RDANGER! Use/Charge the specified Icom batteries only. Only tested and approved for use with genuine Icom batteries. Fire and/or explosion may occur when a third party battery pack or counterfeit product is used/charged. · CAUTION! NEVER short the terminals of the battery pack (or charging terminals of the transceiver). Also, current may flow into nearby metal objects such as a necklace, so be careful when placing battery packs (or the transceiver) in handbags, etc. Simply carrying with or placing near metal objects such as a necklace, etc. causes shorting. This will damage not only the battery pack, but also the transceiver. · NEVER incinerate used battery packs. Internal battery gas may cause an explosion. · NEVER immerse the battery pack in water. If the battery pack becomes wet, be sure to wipe it dry BEFORE attaching it to the transceiver. · Clean the battery terminals to avoid rust or poor contact. · Keep battery contacts clean. It's a good idea to clean battery terminals once a week. If your battery pack seems to have no capacity even after being charged, completely discharge it by leaving the power ON overnight. Then, fully charge the battery pack again. If the battery pack still does not retain a charge (or only very little charge), a new battery pack must be purchased (p. 77). Charging NOTE Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. · Recommended temperature range for charging: +10°C to +40°C (; +50°F to 140°F) · Use the supplied charger or optional charger (BC-119N/121N/144N for rapid charging, BC-146 for regular charging) only. NEVER use other manufacturers' chargers. 3 The optional BP-222N, BP-209N, BP-210N or BP-211N battery packs include rechargeable batteries (Ni-Cd: BP-222N, BP-209N, Ni-MH: BP-210N, Li-Ion: BP-211N) and can be charged approx. 300 times. Charge the battery pack before first operating the transceiver or when the battery pack becomes exhausted. If you want to charge the battery pack more than 300 times, the following points should be observed: · Avoid over charging. The charging period should be less than 24 hours. · Use the battery until it becomes almost completely exhausted under normal conditions. We recommend battery charging after transmitting becomes impossible. D Battery pack life When the operating period becomes extremely short even after charging the battery pack fully, a new battery pack is needed. 9 3 BATTERY PACKS D About AD-99N The adapter (Spacer A) only is required for IC-V82/U82 series. When removing the spacer (Spacer B/C), push the latch carefully with your finger to remove the spacer (Spacer B/C) from the adapter (Spacer A). Remove the spacer (Spacer B/C) from the adapter. Push the latch carefully. Battery charging Recommendation: Charge the BP-211N (Li-Ion) by BC-119N (or BC-121N) for a maximum of 2.5 hours. Li-Ion batteries are different from Ni-Cd batteries in that it is not necessary to completely charge and discharge them to prolong the battery life. Therefore, charging the battery in intervals, and not for extended periods is recommended. D Regular charging with the BC-146 The optional BC-146 provides regular charging of an optional battery pack with or without a transceiver attached. The following is additionally required: · An optional AC adapter. (An AD-99N is supplied with BC-146.) Turn power OFF. Check orientation for correct charging. (Insert together with AD-99N.) R CAUTION! · DO NOT push or force the latch with a screw driver, etc., to remove it. · DO NOT bend the latch when the adapter and spacer are not joined together. This will cause weakening of the latch plastic. · Both cases may break the latch and it may not be able to be reattached. · Chargeable battery BP-210N (Ni-MH battery) BP-209N, BP-222N (Ni-Cd batteries) BC-146+AD-99N 10 BATTERY PACKS D Rapid charging with the BC-144N The optional BC-144N provides rapid charging of optional battery packs. The following are additionally required: · An AC adapter (may be supplied with the BC-144N depending on version). Turn power OFF. 3 D Rapid charging with the BC-119N+AD-101 The optional BC-119N provides rapid charging of battery packs. The following items are additionally required. · AD-101 (Charger Adapter). · An AC adapter (may be supplied with the BC-119N depending on version) or the DC power cable (OPC-515L/CP-17L). Turn power OFF. 3 Check orientation for correct charging. (Insert together with AD-99N.) BC-144N+AD-99N DC power cable (OPC-515L) (Connect with the DC power supply; 13.8 V/at least 2 A) · Chargeable battery BP-210N (Ni-MH battery) BP-209N, BP-222N (Ni-Cd batteries) · Chargeable battery BP-210N (Ni-MH battery) BP-209N, BP-222N (Ni-Cd batteries) BP-211N (Li-Ion battery) 11 3 BATTERY PACKS D Rapid charging with the BC-121N+AD-101 The optional BC-121N allows up to 6 battery packs to be charged simultaneously. The following items are additionally required. · Six AD-101 (Charger Adapter). · An AC adapter (BC-124; may be supplied with the BC-121N depending on version) or the DC power cable (OPC-656). Turn power OFF. Battery case (optional for some versions) When using a BP-208N BATTERY CASE attached to the transceiver, install 6 AA (LR6) size alkaline batteries as illustrated below. AC adapter (purchased separately) D CAUTION Charge indicator (each indicator functions independently) DC power cable (OPC-656) (Connect with the DC power supply; 13.8 V/at least 7 A) · Chargeable battery BP-210N (Ni-MH battery) BP-209N, BP-222N (Ni-Cd batteries) BP-211N (Li-Ion battery) 12 · Use ALKALINE batteries only. · Make sure all battery cells are the same brand, type and capacity. Never mix old and new batteries. Either of the above may cause a fire hazard or damage the transceiver if neglected. · Never incinerate used battery cells since internal battery gas may cause them to rupture. · Never expose a detached battery case to water. If the battery case gets wet, be sure to wipe it dry before use. BASIC OPERATION Power ON Push and hold [PWR] for 1 sec. to turn power ON. 4 3 4 Setting a frequency D Via the keypad q Push [D·CLR] to select VFO mode, if necessary. w To enter the desired frequency, enter 6 digits starting from the 100 MHz digit. · Entering three* to five digits then pushing [·ENT ] will also set the frequency. (*Some versions only requires two digits.) · When a digit is mistakenly input, push [D.CLR] to abort input. PWR Push and hold for 1 sec. · Example 1-- when entering 145.525 MHz Push TONE 1 DUP 4 SCAN 5 SCAN 5 P.BEEP 2 SCAN 5 VFO mode selection The transceiver has 2 basic operating modes: VFO mode and memory mode. · Example 2-- when entering 144.800 MHz Push TONE 1 DUP 4 DUP 4 SET 8 OPT 0 ENT Push [D·CLR] to select VFO mode. D CLR 13 4 BASIC OPERATION D By other methods YZ Via the [Y]/[Z] keys Y Z Push [Y] or [Z] several times to set the desired frequency. · Each push increases/decreases the frequency by the selected tuning step. See next set of instructions for setting tuning step size. For your information-- [VOL] function assignment The [VOL] control can be used as a tuning dial for frequency tuning YZ instead of [Y]/[Z] keys. However, when [VOL] functions as tuning YZ dial, [Y]/[Z] keys functions as volume control. Y Z qWhile pushing [Y] and [Z], turn power ON to enter INITIAL SET MODE. [VOL] D Tuning step selection The IC-V82/U82 has 8 tuning steps-- 5, 10, 12.5, 15, 20, 25, 30 and 50 kHz. The tuning step is selectable in SET MODE. qPush [A·FUNC] then [8·SET] to enter SET MODE. Y Z wPush [Y] or [Z] several times to select the tuning step item. [VOL] PWR Y Z w Push [Y] or [Z] several times to select the dial assignment item, "tOP." e Rotate [VOL] to select the condition. A FUNC ENT ENT SET 8 [VOL] is assigned as AF volume control. [VOL] is assigned as tuning dial. eRotate [VOL] to select the desired tuning step. r Push [·ENT ] to exit SET MODE. r To exit SET MODE, push [·ENT ]. 14 BASIC OPERATION 4 Setting audio/squelch level D To set the audio level Rotate [VOL] to set the desired audio level while receiving a signal. · When no signal is received, push and hold [MONI] while setting the audio level. · When [VOL] is assigned as tuning YZ dial, push [Y]/[Z] to adjust the audio output level. (pgs. 14, 65) [VOL] Receive and transmit q Push and hold [PWR] for 1 sec. to turn the power ON. w Adjust audio volume to the desired level. e Set the frequency. When a signal is received: · Squelch opens and audio is emitted from the speaker. · Signal indicator shows the relative signal strength level. rPush [A·FUNC], then [9·H/M/L] to select output power between high, middle and low. · "L" appears when low power is selected. · "M" appears when middle power is selected. · No indication appears when high power is selected. t Push and hold [PTT] to transmit, then speak into the microphone. · "$" appears. · Do not hold the microphone too close to your mouth or speak too loudly. This may distort the signal. y Release [PTT] to receive. For your information-- Monitor function: 4 D To set the squelch level While pushing [MONI], push YZ [Y]/[Z] to set the squelch level. · The squelch level "1" is loose squelch, "10" is tight squelch. · When [VOL] is assigned as tuning dial, rotate [VOL] while pressing [MONI]. (pgs. 14, 65) MONI Push and hold [MONI] to listen to weak signals that do not open the squelch. 15 4 BASIC OPERATION Display type USING INITIAL SET MODE "Channel Name Indication" type The transceiver has 3 display types to suit your operating style during memory mode operation. The display type is selected in INITIAL SET MODE (p. 65). "Frequency Indication" type Displays memory channel name you have assigned. In this display pre-programmed memory channel names are displayed. VFO mode is selectable. Displays operating frequency. "Channel Number Indication" type · Programmed frequencies are indicated when you have not preprogrammed the channel names in the selected memory channel. · Push and hold [MONI] to display the operating frequency. Key lock function Displays memory channel number. In this type only preprogrammed memory channel numbers are displayed. VFO mode cannot be selected. · When the channel indication type is selected, only the following functions can be performed. - Scan function (p. 30) - Output power setting (p. 15) - DTMF memory function (p. 27) - Key lock function (see next set of instructions) - Scan pause timer setting, function key timer setting and LCD backlight setting in SET MODE (p. 61) The key lock function prevents accidental frequency changes and function activation. Push [A·FUNC] then push and hold [·ENT ] for 1 sec. to toggle the function ON and OFF. · " " appears while the lock function is activated. · [PWR], [PTT], [VOL] and [MONI] can be operated regardless of this setting. A FUNC ENT 16 REPEATER OPERATION General When using a repeater, the transmit frequency is shifted from the receive frequency by the offset frequency. It is convenient to program repeater information into memory channels. q Set the receive frequency (repeater output frequency). w Push [A·FUNC] and [4·DUP] several times to select "­" or "+." · "­" indicates the transmit frequency is shifted down; "+" indicates the transmit frequency is shifted up. · Blinking "­" or "+" indicates the reversed duplex mode is selected in SET MODE (p. 58). 5 SET MODE Reversed duplex mode USING When the reversed duplex mode is selected, the receive frequency shifts. (Transmit frequency shifts in normal duplex mode.) Each receive and transmit frequency is shown in the table below with the following conditions; IC-V82 Input frequency Direction Offset frequency IC-U82 Input frequency Direction Offset frequency : 145.30 MHz : ­ (negative) : 0.6 MHz : 439.80 MHz : ­ (negative) : 5 MHz