S15i Multimedia Projector Product Safety Guide S15i Projecteur multimedia - Guide de Sécurité de Produit S15i Multimedia-Projektor - Sicherheitsanleitung des Geräts S15i Proyector de Multimedia - Guiá de Seguridad del Producto S15i Proiettore Multimediale - Guida di Sicurezza del Prodotto S15i Multimedia Projector - Veiligheidsgids op Product S15i Projector dos Multimedia - Guia da Segurança de Produto S15i Multimedia-Projector- Bruksanvisning för Produktsäkerhets S15i S15i S15i Multimediaprojektori - Laitteen turvaohjeet 2 3MTM Multimedia Projector S15i Product Safety Guide © 3M 2006 ENGLISH Safety Information ........................................................................................................................................5 Product Safety Labels ...................................................................................................................................9 Lamp ...........................................................................................................................................................10 Warranty ......................................................................................................................................................13 © 3M 2006 3MTM Multimedia Projector S15i Product Safety Guide 3 ENGLISH Table of Contents ENGLISH 4 3MTM Multimedia Projector S15i Product Safety Guide © 3M 2006 Read, understand, and follow all safety information contained in the "Product Safety Guide" and in the "Operator's Guide" prior to using the S15i Multimedia Projector. Service personnel must also read and understand the safety information contained in the "Service Manual". Retain these instructions for future reference. Intended Use The 3MTM Multimedia Projector S15i was designed, built and tested for use indoors, using 3M brand lamps, 3M brand ceiling mount hardware and nominal local voltages. This projector is not intended for household use or use by children. The use of other replacement lamps, outdoor operation or different voltages has not been tested and could damage the projector or peripheral equipment and/or create a potentially unsafe operating condition. Explanation of Signal Words and Symbols in Safety Labels and Instructions WARNING: CAUTION: Indicates a potentially hazardous situation, which if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation, which if not avoided, may result in minor or moderate injury. Warning: Hazardous Voltage Warning: Hazardous High Temperature Warning: High Pressure Attention: Refer to Safety Instructions in Guides © 3M 2006 3MTM Multimedia Projector S15i Product Safety Guide 5 ENGLISH Safety Information ENGLISH WARNING · · To reduce the risk associated with choking: - Keep the battery and battery holder away from children and pets. To reduce the risk associated with exposure to hazardous voltage: - Disconnect power cord when the projector is not in use, during lamp replacement, and while cleaning. instructions. Do not store or operate this projector in wet environments. Do not modify this projector. Do not attempt to service the projector - there are no user serviceable parts, other than the lamp cartridge, inside the projector. Contact a 3M authorized service provider for service. - Do not allow water or other liquids to enter the projector. To reduce the risk associated with environmental contamination due to mercury: - Dispose of lamp cartridge in accordance with applicable federal, state and local regulations. - Replace power cord if damaged. - Contact a 3M authorized service provider if the projector becomes damaged. - Use a grounded extension cord with a rating at least equal to that of the projector. - Connect this projector to a grounded outlet. To reduce the risk associated with hazardous voltage, impact, tripping, and intense visible light: - Do not use this projector around unsupervised children. To reduce the risk associated with hot surface of lamp cartridge: - Unplug the projector from the electrical outlet and allow the lamp to cool for 45 minutes before replacing the lamp. To reduce the risk associated with a ruptured lamp: - Always handle the fragile lamp module with care. - Remove the projector from the ceiling or wall mount before replacing the lamp. - Use care when replacing the lamp module in the event of a lamp rupture - small glass particles and small amounts of mercury may be present. - Ventilate the area where the lamp rupture occurred. - Wear safety goggles and gloves when cleaning up ruptured lamp debris. - Carefully collect the ruptured lamp debris in a closed container and dispose of the container and the expired lamp module in accordance with federal, state, and local regulations. - Wash your hands thoroughly after handling ruptured lamp debris. - Replace the lamp module when the lamp replacement message appears. - Never replace the lamp module with a previously used lamp module. · · · · 6 3MTM Multimedia Projector S15i Product Safety Guide © 3M 2006 CAUTION · To reduce the risk associated with explosion, and/or chemicals from a leaking battery: - Use only with battery type AA or equivalent. - Orient the battery's plus (+) and minus (-) terminals of the batteries according to the markings found on the remote control. - Do not leave the battery in the remote for an extended period of time. - Do not carry batteries loose in your pocket or purse. - Avoid eye and skin contact in the event that battery would leak. - Do not mix used and new batteries. To reduce the risk associated with the impact of a falling projector: - Use only the 3MTM brand wall/ceiling mounting hardware kit if wall or ceiling mounting is desired. Adhere strictly to the proper installation procedure as outlined in the installation instructions when installing the 3MTM wall/ceiling kit. · · · To reduce the risk associated with intense visible light: - Avoid looking directly into the projector lens while the lamp is on. To reduce the risk associated with tripping and/or impact: - Position the power cord and data cable so that they cannot be tripped over. © 3M 2006 3MTM Multimedia Projector S15i Product Safety Guide 7 ENGLISH ENGLISH Important Note 1. Always open the lens shutter or remove lens cap when the projection lamp is on. 2. To avoid premature lamp failure, do not change the mounting position of the projector (desktop ceiling mount or ceiling desktop mount) and continue to use the same lamp. 4. To avoid reduced image quality, do not touch projection lens or other internal optical components. 5. Do not use detergents, chemicals, or any spray liquids for cleaning this unit, other than those referred to in the "Operators Guide". 6. For maximum lamp life, do not strike or drop, improperly handle, or scratch the lamp glass. Also, do not install an old or used lamp. Guide". Keep all ventilation openings free of any obstructions. In some countries, the line voltage is NOT stable. This projector is designed to operate safely within a bandwidth of 100 to 120 volts / 220 to 240 volts (50 to 60 Hz) ±10%, but could fail if power drops or surges of ±10 volts occur. In these highrisk areas, it is recommended to install a power stabilizer unit. Do not block intake or exhaust air vents. This will cause the projector to over heat and shut down. Do not place the projector in direct sunlight or near a hot object such as a heater. To prevent damaging the projector, always hold the projector whenever using the elevator buttons to adjust the elevator feet. Use the accessory cable or a designated-type cable for the connection. Some cables have to be used with core set. A too long cable may cause certain picture degradation. Please consult with your dealer for details. For cables that have a core only at one end, connect the core to the projector. Make sure that you connect devices to the correct port. Incorrect connection may result in malfunction and/or damage to the device and/or projector. Do not place the projector in the side/front/rear-up position, except care of the air 8. 9. 10. 11. 12. 13. 14. 15. 8 3MTM Multimedia Projector S15i Product Safety Guide © 3M 2006 © 3M 2006 3MTM Multimedia Projector S15i Product Safety Guide 9 ENGLISH Product Safety Labels ENGLISH Lamp Lamp Operation: The following symptoms may indicate a lamp in need of replacement: · LAMP indicator lights up red. WARNING · To reduce the risk associated with environmental contamination due to mercury in the projection lamp: - Dispose of lamp cartridge in accordance with applicable federal, state and local regulations. - The lamp in this product contains mercuy. Dispose of projection lamp in a manner that is consistent with your local hazardous waste regulations for mercury. - For recycling and disposal information, contact your respective governmental agencies. In U.S., contact the Electronic Industries Alliance at www.lamprecycle.org In Canada, contact the Electronic Product Stewardship Canada at www.epsc.ca Display Lamp Operation Hours To determine the lamp operation hours, follow these steps: 1. While the projector is running, press the MENU button on the remote control. Choose the "OPTION" using the button, and press the button or the ENTER button. Choose the "LAMP TIME" using the button. 2. The operating time of the lamp will be displayed. The lamp time is the time counted after the last resetting. Note Please reset the lamp time only when you have replaced the lamp, for a suitable indication about the lamp. Reset Lamp Hours (1) Press the MENU button to display a menu. Only when the EASY MENU has appeared, please perform the next step (2). appear. time. 10 3MTM Multimedia Projector S15i Product Safety Guide © 3M 2006 The glass lamp used in this projector contains small amounts of mercury and operates at high pressure and at high temperature and may unexpectedly shatter. Each lamp has a different lifetime and can fail in different ways, including a rupture with a loud bang or simply burn out. In the event of a lamp rupture, be sure to follow the instructions. WARNING · To reduce the risk associated with exposure to hazardous voltage: - Disconnect power cord when the projector is not in use, during lamp replacement, and while cleaning. - Do not attempt to service the projector - there are no user serviceable parts, other than the lamp cartridge, inside the projector. Contact a 3M authorized service provider for service. To reduce the risk associated with hot surface of lamp cartridge: - Unplug the projector from the electrical outlet and allow the lamp to cool for 45 minutes before replacing the lamp. To reduce the risk associated with a ruptured lamp: - Always handle the fragile lamp module with care. - Remove the projector from the ceiling or wall mount before replacing the lamp. In the case of a lamp rupture, small glass particles could fall out when the lamp door is opened or the projector is tilted. - Use care when replacing the lamp module in the event of a lamp rupture - small glass particles and small amounts of mercury may be present. - Ventilate the area where the lamp rupture occurred. - Wear safety goggles and gloves when cleaning up ruptured lamp debris. - Carefully collect the ruptured lamp debris in a closed container and dispose of the container and the expired lamp module in accordance with federal, state, and local regulations. - Wash your hands thoroughly after handling ruptured lamp debris. - Replace the lamp module when the lamp replacement message appears. - Never replace the lamp module with a previously used lamp module. To reduce the risk associated with environmental contamination due to mercury: - Dispose of lamp cartridge in accordance with applicable federal, state and local regulations. · · · CAUTION · To reduce the risk associated with explosion, and/or chemicals from a leaking battery: - Use only with battery type AA or equivalent. - Orient the battery's plus (+) and minus (-) terminals of the batteries according to the markings found on the remote control. - Do not leave the battery in the remote for an extended period of time. - Do not carry batteries loose in your pocket or purse. - Avoid eye and skin contact in the event that battery would leak. - Do not mix used and new batteries. To reduce the risk associated with intense visible light: - Avoid looking directly into the projector lens while the lamp is on. · Important Note: elsewhere besides the lamp. If this happens, contact your local dealer or a service representative. © 3M 2006 3MTM Multimedia Projector S15i Product Safety Guide 11 ENGLISH Replacing Lamp ENGLISH Note For maximum lamp life, do not strike or drop, improperly handle, or scratch the lamp glass. Also, do not install an old or previously used lamp. 1. Remove lamp access door: Please loosen the screw (marked by arrow) (1). Then, unhook the claws of the lamp door (2), and remove the ...