SCANNER ACCESSIBILITY OPTION (Machine Code: G570) INSTALLATION PROCEDURE For Machine code: B178/B180/B202 Copiers NOTE: THE SCANNER ACCESSIBILITY OPTION MUST BE INSTALLED BY A CUSTOMER SERVICE REPRESENTATIVE WHO HAS COMPLETED THE TRAINING COURSES ON THE BASE COPIER AND THE SCANNER ACCESSIBILITY OPTION. G5708560 G5708560 INSTALLATION REQUIREMENTS Machine Level Front to back: Within 5 mm (0.2")/ 5° Right to left: Within 5 mm (0.2")/ 5° Location Requirement Put the scanner on the right side of the mainframe as shown. NOTE: 1) Make sure that the scanner is placed 660~724 mm above the floor. 2) Make sure that the scanner cable does not touch the floor. 3) Make sure to tell the user not to let the scanner cable get caught in things such as a wheelchair. . G570I311.WMF Requirement Condition Attach the platen cover option to the mainframe to cover the exposure glass. Install the scanner on a solid base. Do not install the scanner in areas where the unit can fall down when the ADF cover is opened. Make sure you install the unit in areas that let the user get easy access to operate the unit. Ask the customer what their requirements are before you install the unit. 1 ACCESSARY CHECK Check the accessories and their quantities against the following list. Description Q'ty 1. Exposure Glass Cleaner Holder ............................................ 1 2. Exposure Glass Cleaner ........................................................ 1 3. M3 x 6 screw.......................................................................... 12 4. M3 x 8 screw.......................................................................... 1 5. Ground screw ........................................................................ 1 6. Core ....................................................................................... 2 7. Left support............................................................................ 1 8. Right stay............................................................................... 1 9. Bracket................................................................................... 1 1 2 3 4 5 6 7 9 8 G570I300.WMF 2 INSTALLATION PROCEDURE NOTE: This installation procedure uses the following symbols. !: Screws ": Connectors #: Clamps !CAUTION Unplug the copier power cord before you do the following procedure. 1. Remove the all tapes. 2. Remove rear cover [A] (! x 5). [A] G570I301.WMF 3. Remove the ground cable [B] (! x 2). 4. Remove the duct [C] (! x 2, " x 1). [C] [B] G570I302.WMF 3 [A] [D] [C] [B] [E] G570I303.WMF [F] 5. Remove the DF connector cable [A] (! x 2, " x1). NOTE: Keep these screws. You will use these screws later. 6. Remove the connector bracket [B]. 7. Disconnect the connector [C] of the IPU harness and release the clamp [D]. 8. Remove the core [E] from the I/F cable. NOTE: Keep this core. You will use this core later. [G] [K] [J] [I] [F] [H] G570I304.WMF 9. Disconnect the I/F cable [F] from the IPU (! x 2). Then put it inside the machine. 10. Disconnect the harness [G] from the scanner unit to the SIO (" x 3, # x 1). Then put this harness inside the scanner frame. 11. Connect the connector of the DF connector cable [H] to the SIO board. 12. Bind the IPU harness [I] and DF connector cable [H] with the clamp [J]. Keep these in the machine. 13. Attach the connector bracket [K] to the SIO board to keep this bracket. 4 [B] [C] [A] 14. Disconnect the PSU cable connector [A]. G570I305.WMF 15. Detach the SIO board with bracket [B] (! x 4). Then slide it to the right slightly. 16. Attach the bracket [C] (! x 5). 17. Attach the SIO board with the bracket again (! x 4). [E] [D] G570I306.WMF 18. Attach the right support [D] (! x 2). 19. Attach the left support [E] (! x 2). 5 [A] [D] [B] G570I307.WMF [E] [C] 20. Put the I/F cable [A] through the opening on the frame. Then attach the core [B] to the I/F cable. 21. Connect the I/F cable connector [C]. Then attach the cable holder [D] (! x 1) and the ground [E] (! x 1) to the frame. [F] [I] [H] [G] G570I308.WMF 22. Put the IPU cable [F] through the opening on the frame. Then attach the two cores [G] to the IPU cable. 23. Connect the IPU cable connector [H] and attach the ground [I] (! x 1). 6 [D] [C] [B] [A] G570I309.WMF 24. Connect the PSU cable connector [A] and attach the ground [B] (ground screw x 1). 25. Attach the scanner bracket [C] to the supports (! x 3) and the ground [D] (! x 1). 26. Install the duct (! x 2, " x 1) and ground cable (! x 2). 27. Cut the panel [E] surrounded with the cutout line. NOTE: File the edge of the cutout line. 28. Make the hole [F] for a screw on the rear cover with a screwdriver. 29. Attach the rear cover (M3x8 screw x 6). [E] [F] G570I310.WMF 7 ...