Installation Guide LP 740 Series Ceiling Mount Installation Guide LP 740 Series Installationhandbuch zur Deckenbefestigung English . . . . . . . . . . . . .1 Deutsch . . . . . . . . . .13 010-0170-00 Copyright © 1998 by In Focus, Inc. Wilsonville, Oregon. All rights reserved. Copyright © 1998 by In Focus, Inc. Wilsonville, Oregon, USA. Alle Rechte vorbehalten. CEILING MOUNT INSTALLATION GUIDE The LP 740 LiteMountTM makes it easy to hang your projector from the ceiling for fixed installation use in meeting, auditorium and training room settings. You must determine the suitability of this product for your intended use and assume all risk and liability in connection therewith. In Focus recommends that a professional contractor or other facilities professional assist you in mounting this device. Be sure to take precautions to meet all local building codes. Additional LiteMount Products In Focus offers two additional LiteMount products that may make your ceiling mount installation easier. · The LiteMount False Ceiling Plate WARNING: This installation must be performed in compliance with your local building code requirements. Local requirements take precedence over any instructions given in this guide. (SP-LTMT-PLT) is designed for suspended ceilings with acoustic tiles. It mounts in your ceiling in place of a ceiling tile. It is preassembled with threaded studs to install the LiteMount brackets, and includes the necessary hardware to attach to the brackets. · The LiteMount Pipe Tubing Extension (SPLTMT-EXT) allows you to install the projector in a room with a high ceiling. With the extension, you can place the projector from 24" (61 cm) to 46" (117 cm) from the ceiling (12" to 24" with cut). Contact your In Focus dealer to order these products. Placing the Projector Refer to the LP 740 User's Guide for image distances and sizes to determine where to install the ceiling mount to meet your projection needs. 1 Contents Contents The LP 740 Ceiling Mount package contains: 1 Installation Guide NOTE: The maximum load the ceiling mount can support is 50 pounds. 2 ceiling mount base box dimensions: 11.6" x 10" x 1.5" weight: 4.2 lbs 3 projector mounting bracket dimensions: 12" x 7.8" x 1.5" weight: 2.2 lbs 4 hardware for installing the projector mounting bracket on the projector: · three (3) 5 mm Phillips-head screws · three (3) 5 mm quick release sleeves · one (1) 5 mm knurled knob screw 5 hardware for installing the projector (with mounting plate) to the base box in the ceiling: · four (4) 6mm knurled knob screws · two (2) 6 mm flat washers · two (2) 6 mm conical spacers 2 Install the Ceiling Mount Base Box on the Ceiling Instructions for installing the ceiling mount on the LiteMount False Ceiling Plate and the LiteMount Pipe Tubing Extension are given in this installation guide. If you have not purchased either of these products, consult a professional contractor or other facilities professional to ensure a safe installation. Please refer to the LiteMount False Ceiling Plate and LiteMount Pipe Tubing Extension installation instructions for lists of included hardware. 1 Center the ceiling mount base box on the ceiling plate as shown in Figure 1. Make sure the front of the base box faces forward toward your projection screen. The front side of the base box is the only surface without drilled holes. 2a LiteMount False Ceiling Plate - Align the holes in the base box with the threaded studs on the plate. Install the 4 washers and nuts as shown in Figure 1. 2b LiteMount Pipe Tubing Extension - Line up the holes in the base box with the holes in the plate at the end of the pipe extension. Install the hardware as shown in Figure 2. WARNING: The ceiling structure must be able to support at least 5 times the weight of the projector and mounting hardware. If not, it must be reinforced according to your local building codes. NOTE: Refer to the Installation Instructions that came with the LiteMount False Ceiling Plate and the LiteMount Pipe Tubing Extension for important additional information. 3 In stal l t he Ce il ing Mou nt B ase B ox on the C ei lin g 3 Place the ceiling plate or pipe extension in the ceiling so that the base box hangs down into the room. 4 Route the projector's cables through your ceiling and out the hole in the ceiling. WARNING: If the dropped ceiling is an airhandling plenum, be sure the cables are plenumrated, or install the cables within conduit. make sure this surface faces front FIGURE 1 Install the base box to the LiteMount False Ceiling Plate 4 false ceiling plate make sure this surface faces front FIGURE 2 Install the base box to the LiteMount Pipe Tubing Extension 5 Attach the Mounting Plate to the Projector Attach the Mounting Plate to the Projector 1 Set the projector on a table with the bottom side up. Align the holes in the mounting plate with the holes in the projector. 2 Insert the 3 screws into the 3 quick release sleeves (Figure 3). 3 Loosely attach the screws and sleeves to the holes in the projector as shown in Figure 3. 4 Align the keyholes in the mounting bracket with the screws in the projector. Slide the mounting bracket until the quick release sleeves are at the top of the keyhole slot. 5 Attach the 5mm knurled knob to the projector in the location shown in Figure 3. Tighten the three 5mm screws and the 5 mm knurled knob. Be careful not to over-tighten the screws. CAUTION: Use only the hardware that is provided with the LP 740 Ceiling Mount. Using different hardware may damage your projector. knurled knob goes here quick release screws FIGURE 3 Attach the mounting plate to the projector 6 Hang the Projector on the Ceiling 1 Loosely install the 6 mm knurled knobs, flat washers, and conical spacers to the 2 hinge pins on the base box (Figure 4). spacer washer knurled knob slide projector bracket here between the base box and the spacer FIGURE 4 Attach knurled knobs to the side of the base box 2 Make sure your cables are pulled through the center hole of the base box, then carefully lift the projector and turn it upside down so the mounting plate faces the ceiling (Figure 5). 3 Insert the projector and mounting bracket slots onto the base box hinge pins between the spacers and base box (Figure 4). Slide the projector bracket forward until the hinge pins rest fully in the vertical slots and support the projector. 7 Hang the Projector on the Ceiling FIGURE 5 Install the projector in the ceiling base box 4 Insert the remaining two 6 mm knurled knobs through the rear slots in the mounting bracket and into the holes on the sides of the base box. Insert knurled knob through this slot FIGURE 6 Insert the knurled knobs to adjust the angle 8 5 Adjust the angle of the projector so that it will project correctly. Refer to your LP 740 User's Guide for detailed information on projection angles and image sizes. 6 Tighten all the knurled knobs to secure the projector in position. 7 Check all fasteners to make sure they are properly tightened. 8 Connect the power cord and the cables to the projector. (Refer to your LP 740 User's Guide for information about connecting the cables.) 9 Inverting the Image When you need to remove the projector or replace the lamp or clean the air filter: 1 Disconnect all cables. 2 Hold the projector from underneath. 3 Remove the knurled knob that holds the projector to the mounting plate. 4 Slide the projector to release it from the quick release bolts. The projector will come off of the mounting plate. The mounting plate will still be attached to the base box. 5 Replace the lamp or clean the air filter as described in your LP 740 User's Guide if needed. 6 Realign the quick release bolts in the keyhole slots on the mounting plate. 7 Fasten the knurled knob. ADJUSTING THE IMAGE Inverting the Image 1 Press the Menu button on the remote or keypad to display the projector's on-screen menu. 2 Using the arrow buttons, move the cursor to the Custom Setup menu, then press Enter. 3 Move the cursor to the Image Mode menu and press Enter. Move the cursor to Ceiling, then select ON. 10 Limited Warranty In Focus Inc. warrants that each "ceiling mount" sold hereunder will conform to and function in accordance with the written specifications of In Focus. Said limited warranty shall apply only to the first person or entity that purchases the Product for personal or business use and not for the purpose of distribution or resale. The product may contain recycled components that are in new condition. Said warranty shall continue for a period of one (1) year from the date of such purchase. Proof of purchase is required for all warranty claims. In Focus does not warrant that the Product will meet the specific requirements of the first person or entity that purchases the Product for personal or business use. In Focus' liability for the breach of the foregoing limited warranty is limited to the repair or replacement of the Product or refund of the purchase price of the Product, at In Focus' sole option. To exercise the Purchaser's rights under the foregoing warranty, the Product must be returned at the Purchaser's sole cost and expense, to In Focus, and must be protected by packaging comparable to the original packaging. The Product must be accompanied by a written letter that includes (i) proof of date of purchase, (ii) the dealer's name, (iii) the part number of the accessory item or the projector/panel model number, (iv) your business card information, (v) explanation of how the item was damaged, and (vi) description of the damage and reason for the return. Please call In Focus or your dealer for information on where to send your case. In Focus will repair/replace and return the case within 10 days of receipt of the item. Warranty Limitation and Exclusion In Focus shall have no further obligation under the foregoing limited warranty if the Product has been damaged due to abuse, misuse, neglect, accident, unusual physical stress, unauthorized modifications, tampering, alterations, or service other than by In Focus, causes other than from ordinary use or failure to properly use the Product in the application for which said Product is intended. Disclaimer or Unstated Warranties The warranty printed above is the only warranty applicable to this purchase. All other warranties, express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose are disclaimed. There are no warranties that extend beyond the face hereof and the foregoing warranty shall not be extended, altered or varied except by written instrument signed by In Focus. Limitation of Liability It is understood and agreed that In Focus' liability whether in contract, in tort, under any warranty, in negligence or otherwise shall not exceed the return of the amount of the purchase price paid by purchaser and under no circumstances shall In Focus be liable for special, indirect or consequential damages or lost profits, lost revenues, or lost savings. The price stated for the product is a consideration in limiting In Focus' liability. No action, regardless of form, arising out of the agreement to purchase the product may be brought by purchaser more than one year after the cause of action has accrued 11 INSTALLATIONSANLEITUNG FÜR DIE DECKENBEFESTIGUNG Mit dem LiteMountTM der LP-Serie 740 können Sie Ihren Projektor mühelos zur permanenten Verwendung in Besprechungs-, Vortrags- und Schulungsräumen an der Decke befestigen. Sie müssen die Eignung dieses Produkts für den beabsichtigten Verwendungszweck überprüfen und übernehmen das gesamte Risiko und die volle Haftung in Zusammenhang mit diesem Produkt. In Focus empfiehlt, daß Ihnen ein Berufshandwerker bei der Befestigung dieses Geräts behilflich ist. Vergewissern Sie sich, daß alle örtlich geltenden Bauvorschriften beachtet werden. LiteMount-Zusatzprodukte In Focus bietet zwei zusätzliche LiteMount-Produkte an, die die Installation der Deckenbefestigung erleichtern. · Die LiteMount-Zwischendeckenplatte (SPLTMT-PLT) ist für abgehängte Decken mit WARNUNG: Diese Installation muß gemäß den jeweils geltenden Bauvorschriften durchgeführt werden. Die örtlichen Bauvorschriften haben Vorrang vor den Anleitungen in dieser Unterlage. Schallschutzfliesen vorgesehen. Sie wird an der Decke anstelle einer Deckenfliese angebracht und verfügt über vorgebohrte Löcher zur Montage der LiteMount-Halterung. · Mit der LiteMount-Rohrverlängerung (SPLTMT-EXT) können Sie den Projektor in einem Raum mit einer hohen Decke installieren. Mit Hilfe der Verlängerung können Sie den Projektor 61 bis 117 cm von der Decke entfernt anbringen. Diese Produkte können Sie bei Ihrem In FocusHändler bestellen. 13 Plazierung des Projektors Plazierung des Projektors Um die optimale Deckenbefestigungsposition für Ihre Projektionsansprüche zu bestimmen, schlagen Sie bitte die Bildentfernung, die Bildgröße und den ...