YOUR LIFE. OUR INSPIRATION. Dishwasher Installation Instructions Instructions d'installation du lave-vaisselle Instrucciones de instalación para lavavajillas Cycle Countdown On/Off Power Scrub Plus Scrub Wash Regular Wash Delicate/ Econo Quick Wash Rinse & Hold Refill Rinse Agent Power Delay Start Hours Top Rack Only Cancel Drain Use and Care Manual located on reverse side Tourner le guide pour les instructions d'utilisation et d'entretien Voltee el manual para encontrar las instrucciones de uso y cuidado 9000060331 (8503) Table of Contents / Important Instructions Table of Contents IMPORTANT INSTRUCTIONS ................................ 1 Tools Needed ........................................................... 2 Materials Needed ..................................................... 2 Materials Supplied ................................................... 3 Enclosure Preparation ............................................. 4 Electrical Preparation .............................................. 5 Plumbing Preparation ........................................... 6-7 Dishwasher Preparation ........................................ 7-8 Door Panel Installation ............................................. 9 Placing the Dishwasher ......................................... 10 Securing the Dishwasher ....................................... 10 Drain Hose Connection .......................................... 11 Hot Water Connection ............................................ 12 Electrical Connection ........................................ 13-14 Door Tension Adjustment ....................................... 14 Base and Toe Panel .......................................... 14-15 Final Instructions ................................................... 15 Customer Service .................................................. 16 Important Safety Instructions WARNING To avoid possible injury or property damage, OBSERVE ALL WARNINGS AND CAUTIONS. These instructions are intended for use by qualified installers only. The dishwasher must be installed by a qualified service technician. · In addition to these instructions, the dishwasher shall be installed to meet all electrical and plumbing codes and ordinances (both national and local). Read these installation instructions completely and follow them carefully. They will save you time and effort and help to ensure safety and optimum dishwasher performance. IMPORTANT · The dishwasher drain hose must be installed with a portion of it at least 20" (508mm) off the cabinet floor; otherwise the dishwasher may not drain properly. · This dishwasher is intended for residential use only, and should not be used in commercial food service establishments. · NEW INSTALLATION - If the dishwasher is a new installation, most of the work must be done before the dishwasher is moved into place. · REPLACEMENT - If the dishwasher is replacing another dishwasher, check the existing dishwasher connections for compatibility with the new dishwasher, and replace parts as necessary. Inspect the Dishwasher After unpacking the dishwasher and prior to installation, thoroughly inspect the dishwasher for possible freight or cosmetic damage. Report any damage immediately. Cosmetic defects must be reported within 5 days of installation. NOTE: Do not discard any bags or items that come with the original package until after the entire installation has been completed. If the dishwasher is installed in a location that experiences freezing temperatures (e.g., in a holiday home), you must drain all the water from the dishwasher's interior. Water system ruptures that occur as a result of freezing are not covered by warranty. 1 Tools and Materials Needed TOOLS NEEDED Hammer Hole Saw Pipe Wrench Adjustable Wrench Tape Measure Slot Screwdriver Phillips Screwdriver Torx Screwdriver Wire Cutter Wire Stripper Drill Level MATERIALS NEEDED (Additional materials may be required to comply with local codes.) Electrical Supply Cable - Minimum #14 AWG, 2 conductor, 1 ground, insulated copper conductors rated 75°C or higher. Hot Water Supply Line - Minimum 3/8" O.D. copper tubing or metal braided dishwasher supply line. Shut-off valve and fittings appropriate for hot water supply line (copper tubing/ compression fitting, or braided hose). 90° elbow with 3/8" N.P.T. male threads on one leg, and sized to fit your water supply line (copper tubing/compression fitting, or braided hose) on the other leg. Teflon tape or other pipe thread compound to seal plumbing connections. UL listed conduit connector or strain relief. 2 Materials Supplied MATERIALS SUPPLIED Accessory Parts Supplied Accessory parts for your dishwasher come in one or more plastic bags that are outlined below. NOTE: Make sure you save all the bags until you have completed your installation. Manual Set Bag A Manual Set Bag is provided with each dishwasher and includes: A Use & Care Instructions and Installation Instructions (both manuals may be included in a single "flip-style" book B Quick Reference Guide (select models) C Extra Tall Item Sprinkler D SHI and SHV Installation Template (SHI and SHV models only) E White Cotton Insulation Strip (SHY66C, SHX99A, SHE66C, SHE99C, SHX57C and SHV57C models only) Dishwasher Installation Kit A Dishwasher Installation Kit is provided with each dishwasher and includes: F Toe Panel Screws (2 black machine screws) Note: These screws are included, but not used on models with the Toe Panel Installation Kit. G Counter Top Mounting Brackets (2 "L" shaped metal brackets) H Mounting Bracket Screws (2 silver wood screws) I Rubber Drain Hose Adaptor (1 black rubber tube) J Hose Clamps ( 1 silver spring clamp to use to attach the rubber adaptor to the Drain Hose and 1 gold screw clamp to attach the rubber adaptor to the plumbing) K Wire Nuts (3 for electrical connection) L Electrical Junction Box Screws (2 silver machine screws) M Leg Leveler Locking Screws (2 gold coarse threaded screws) SHI/SHV Door Panel Installation Kit A Door Panel Installation Kit is provided with select dishwashers that use a custom wood door panel and includes: N Plastic Caps (2) O Spring Tension Screws (2 larger silver machine screws used to adjust the door springs to accommodate doors of different weights) P Door Mounting Brackets (2 gold metal brackets and 2 white plastic brackets used to mount the custom door) Q Door Mounting Bracket Screws (8 silver wood screws) R Door Mounting Screws (2 long silver screws used to attach the door) Toe Panel Installation Kit A Toe Panel Installation Kit is provided on models SHY66C, SHX99A, SHE66C, SHE99C, SHX57C, and SHV57C. These models have a special noise reducing Toe Panel with the following mounting hardware: S Toe Panel Screws (2 black screws used to attach the metal Toe Panel) T Black Plastic Base Access Panel Screws (2 long silver screws used to attach the Black plastic Base Access Panel to the dishwasher. A D B E C F K G L M H I J N O R P Q S T 3 Enclosure Preparation 23-9/16" (598mm) WARNING Electrical Shock Hazard To avoid electrical shock, make sure the water supply and electrical supply are shut off before installation or service. 90 90 34" (864mm) minimum ENCLOSURE PREPARATION NOTE: This dishwasher is designed to be enclosed on the top and both sides by standard residential kitchen cabinetry. 23-5/8" ­ 24-1/4" (600­616 mm) Figure 1 Select a location as close to the sink as possible for easy access to water supply and drain lines. For proper dishwasher operation and appearance, ensure that the enclosure is square and has the dimensions shown in Figure 1. If the dishwasher is to be installed in a corner, make sure that there is adequate clearance to open the door. See Figure 2. Check clearance between dishwasher door and wall WARNING Countertop Electrical Shock/Fire Hazard To avoid electric shock or fire, do not allow the electrical and water supply lines to touch. Separate channels are provided under the dishwasher (see page 10). If the enclosure requires openings for the electrical supply cable, hot water supply line, and dishwasher drain hose, place them within the dimensions shown by the shaded area of Figure 3 to avoid interference with the dishwasher frame or other components. Make the openings for the electrical supply cable and hot water supply line 1" (25.4mm) diameter. Make the opening for the dishwasher drain hose 1-1/4" (32mm) diameter. If the openings are made through wood, sand them smooth. If the openings are made through metal, make them large enough to accommodate grommets or other protective sheaths with inside diameters of 1" (25.4mm) for the electrical supply cable and the hot water supply line, and 1-1/4" (32mm) for the dishwasher drain hose. Figure 2 3-1/2" (89mm) 1-5/16" (33mm) Figure 3 4 Electrical Preparation ELECTRICAL PREPARATION WARNING Electrical Shock Hazard To avoid electrical shock, do not work on an energized circuit. Doing so could result in serious injury or death. Only qualified electricians should perform electrical work. Do not attempt any work on the dishwasher electric supply circuit until you are certain the circuit is de-energized. 30" (762mm) 21" (533mm) Figure 4 WARNING Fire Hazard Dishwasher Electrical Rating Volts 120 Hertz 60 A mperes 15 Watts 1 ,4 5 0 (m ax) To avoid a fire hazard, make sure electrical work is properly installed. Only qualified electricians should perform electrical work. Electrical Supply The customer has the responsibility of ensuring that the dishwasher electrical installation is in compliance with all national and local electrical codes and ordinances. The dishwasher is designed for an electrical supply of 120V, 60 Hz, AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated for 15 amps. Electrical supply conductors shall be a minimum #14 AWG copper wire rated at 75°C or higher. Regardless of where the electrical supply cable enters the enclosure (following the guidelines on page 8), position the cable 21" (533mm) from the enclosure's left side, as shown in Figure 4. Extend the cable 30" (762mm) from the enclosure's back, as shown in Figure 4. Remove 3" - 4" (75mm - 100mm) of the cable's outer casing, as shown in Figure 5, then remove 3/8" - 1/2" (9 - 13mm) of insulation from each wire, as shown in Figure 5. 3" - 4" ( 75mm - 100mm) 3/8" - 1/2" ( 8mm - 13mm) Figure 5 5 Plumbing Preparation PLUMBING PREPARATION Shut off Valve WARNING 14" (355mm) Hot Water Supply Line Scald Hazard To avoid being scalded, do not perform any work on a charged hot water line. Serious injury could result. Only qualified plumbers should perform plumbing work. Do not attempt any work on the dishwasher hot water supply plumbing until you are certain the hot water supply is shut off. Figure 6 Temperatures required for soldering and sweating will damage the dishwasher's base and water inlet valve. If plumbing lines are to be soldered or sweated, keep the heat source at least 6 inches (152.4 mm) away from the dishwasher's base and water inlet valve. Hot Water Supply The hot water heater should be set to deliver approximately 120° F (49° C) water to the dishwasher. Water that is too hot can cause some detergents to lose effectiveness. Lower water temperatures will increase run times. The hot water supply pressure must be between 15 - 145 psi (1 - 10 bars). Hot Water Supply Plumbing Install an easily accessible shut-off valve (not supplied) in the hot water supply line, as shown in Figure 6. All solder connections must be made before the water line is connected to the dishwasher's water inlet valve. Water may also be supplied to the dishwasher by using a braided hose line. Check with your local plumbing supply sources for the proper hose and 90° elbow fitting. NOTE: Regardless of where the hot water supply line enters the enclosure, position the line 14" (355mm) from the enclosure's left side, as shown in Figure 6. NOTE: Decide whether braided hose or copper tubing will be used for the hot water supply plumbing, and purchase the correct type of hot water supply shut-off valve, 90° elbow, and necessary fittings for the hot water supply plumbing. 6 Plumbing Preparation/ Dishwasher Preparation Air Gap PLUMBING PREPARATION (continued) Drain Plumbing Under Sink Drain Connection If the dishwasher is to drain either directly into the household drain plumbing or through an air gap, install a y-branch tailpiece under the sink as shown in Figure 7. Installing an Air Gap If local ordinances require an air gap, as shown in Figure 8, install it according to the manufacturer's instructions. Disposer Make sure to remove the disposer's dishwasher drain connection plug before connecting the dishwasher drain hose. See Figure 9. Y-branch Tailpiece Figure 7 Figure 8 DISHWASHER PREPARATION Dishwasher preparation involves four tasks: · Installing the Mounting Brackets · Removing the Toe Panel · Ins ...