User manual JVC DR-M100SUS - DR-M100 - Instruction Manual

DVD VIDEO RECORDER DR-M100S CH + RAM/RW STANDBY/ON PUSH-OPEN CH- i For Customer Use: Enter below the Model No. and Serial No. which are located on the rear of cabinet. Retain this information for future reference. Model No. Serial No. INSTRUCTIONS LPT1013-001B EN 2 EN SAFETY FIRST WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. CAUTION: This unit should be used with AC 120VH, 60Hz only. To prevent electric shocks and fire hazards, DO NOT use any other power source. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. CAUTION: Changes or modifications not approved by JVC could void user's authority to operate the equipment. Dear Customer, Thank you for purchasing the JVC DVD video recorder. Before use, please read the safety information and precautions to ensure safe use of your new unit. Cautions CAUTION: A UNIT IS A CLASS 1 LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED. WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL. CLASS 1 LASER PRODUCT REPRODUCTION OF LABELS WARNING LABEL INSIDE OF THE UNIT SAFETY FIRST EN 3 IMPORTANT PRODUCT SAFETY INSTRUCTIONS Electrical energy can perform many useful functions. But improper use can result in potential electrical shock or fire hazards. This product has been engineered and manufactured to assure your personal safety. In order not to defeat the built-in safeguards, observe the following basic rules for its installation, use and servicing. ATTENTION: Follow and obey all warnings and instructions marked on your product and its operating instructions. For your safety, please read all the safety and operating instructions before you operate this product and keep this booklet for future reference. INSTALLATION 1. Grounding or Polarization (A)Your product may be equipped with a polarized alternatingcurrent line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. (B)Your product may be equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 2. Power Sources Operate your product only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. If your product is intended to operate from battery power, or other sources, refer to the operating instructions. 3. Overloading Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 4. Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 5. Ventilation Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. Do not block the openings by placing the product on a bed, sofa, rug or other similar surface. Do not place the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 6. Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer. ANTENNA INSTALLATION INSTRUCTIONS 1. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. 2. Lightning For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 3. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 4 EN SAFETY FIRST SERVICING 1. Servicing If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions, do not attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 2. Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e. If the product has been dropped or damaged in any way. f. When the product exhibits a distinct change in performance^this indicates a need for service. 3. Replacement Parts When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or which have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. 4. Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in safe operating condition. HOW TO USE THIS INSTRUCTION MANUAL All major sections and subsections are listed in the Table Of USE 1. Accessories To avoid personal injury: Do not place this product on an unstable cart, stand, tripod, bracket, or table. It may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product. Use a mounting accessory recommended by the manufacturer and follow the manufacturer's instructions for any mounting of the product. Do not try to roll a cart with small casters across thresholds or deep-pile carpets. 2. Product and Cart Combination A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 3. Water and Moisture Do not use this product near water^for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool and the like. 4. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or shortout parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 5. Attachments Do not use attachments not recommended by the manufacturer of this product as they may cause hazards. 6. Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 7. Heat The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. Contents on page 6. Use this when searching for information on a specific procedure or feature. The Index on pages 12 - 14 illustrates the controls and connections on the front and rear panel, the front display panel and the remote control. The list of terms on page 70 lists frequently-used terms, and the number of the page on which they are used or explained in the manual. The A mark signals a reference to another page for instructions or related information. Operation buttons necessary for the various procedures are clearly indicated through the use of illustrations at the beginning of each major section. BEFORE YOU INSTALL YOUR NEW UNIT . . . . . . please read the sections/literature listed below. "SAFETY FIRST" (A pg. 2) AIMPORTANT PRODUCT SAFETY INSTRUCTIONSB (A pg. 3 - 5) SAFETY FIRST Declaration of Conformity Model Number:DR-M100SU Trade Name:JVC Responsible Party:JVC Americas Corp. Address:1700 Valley Road Wayne, N.J. 07470 Telephone Number:973-317-5000 This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. EN 5 When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm or more on both sides, on top and at the rear). When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly. Failure to heed the following precautions may result in damage to the unit, remote control or disc. 1. DO NOT place the unit ^ ^ in an environment prone to extreme temperatures or humidity. ^ in direct sunlight. ^ in a dusty environment. ^ in an environment where strong magnetic fields are generated. ^ on a surface that is unstable or subject to vibration. 2. DO NOT block the unit's ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.) 3. DO NOT place heavy objects on the unit or remote control. 4. DO NOT place anything which might spill on top of the unit or remote control. (If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.) 5. DO NOT expose the apparatus to dripping or splashing. 6. DO NOT use this equipment in a bathroom or places with water. Also DO NOT place any containers filled with water or liquids (such as cosmetics or medicines, flower vases, potted plants, cups, etc.) on top of this unit. 7. DO NOT place any naked flame sources, such as lighted candles, on the apparatus. 8. AVOID violent shocks to the unit during transport. MOISTURE CONDENSATION Moisture in the air will condense on the unit when you move it from a cold place to a warm place, or under extremely humid conditions^just as water droplets form on the surface of a glass filled with cold liquid. In conditions where condensation may occur, disconnect the unit's power plug from the wall and keep it disconnected for a few hours to let the moisture dry, then turn on the unit. DISCLAIMER OF LIABILITY: JVC shall not be liable for any loss relating to the unit's failure to properly record, store or playback any content (video, audio or otherwise) for any reason whatsoever. Any applicable warranties shall only cover replacement or repair of the effected unit, and shall not apply to recovery or replacement of lost content. ATTENTION: 8 Using a mobile phone in the vicinity of the unit may cause picture vibration on the TV screen or change the screen to a blue back display. 8 Some TVs or other appliances generate strong magnetic fields. Do not place such appliances on top of the unit as it may cause picture disturbance. 8 If there is a power outage when using the unit, the recorded data may be erased. 8 Recorded programmes and data cannot be restored once the disc is damaged. Manufactured under licence from Dolby Laboratories. ADolbyB i and double-D symbol are trademarks of Dolby Laboratories. ADTSB and ADTS DIGITAL OUTB are trademarks of Digital Theater Systems, Inc. VCR Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation. The VCR Plus+ system is manufactured under license from Gemstar Development Corporation. DSS is an official trademark of DIRECTV, Inc., a unit of GM Hughes Electronics. DISH Network is a trademark of Echostar Communications Corporation. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing users only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. TM TM 6 EN CONTENTS 2 7 12 16 17 EDITING 53 SAFETY FIRST DISC INFORMATION INDEX INSTALLING YOUR NEW UNIT INITIAL SETTINGS About Discs ....................................................................................7 DV Dubbing ................................................................................. 53 Edit From A Camcorder ............................................................... 54 Edit To Or From Another Recorder ............................................. 55 Digital Audio Dubbing .................................................................. 56 REMOTE CONTROL/SYSTEM CONNECTIONS 57 Basic Connection .........................................................................16 Remote Control Functions ........................................................... 57 Connecting To A Dolby Digital Decoder Or An Amplifier With Built-in DTS....................................................................... 57 Plug & Play Set ............................................................................17 Language .....................................................................................18 Clock Set......................................................................................19 Tuner Set .....................................................................................20 Monitor Set...................................................................................21 SUBSIDIARY SETTINGS 58 BASIC OPERATIONS ON DVD DECK 22 Basic Playback.............................................................................22 Playback Features .......................................................................23 Live Memory Playback .................................................................27 Using The On-screen Bar ............................................................30 Basic Recording ...........................................................................34 Recording Features......................................................................35 Mode Set ..................................................................................... 58 Scan Mode Set ............................................................................ 60 Tray Lock ..................................................................................... 61 Child Lock .................................................................................... 61 Changing VCR Plus+ Setting ...................................................... 62 Format A Disc .............................................................................. 63 Finalize A Disc ............................................................................. 64 TROUBLESHOOTING APPENDIX SPECIFICATIONS LIST OF TERMS WARRANTY (Only in U.S.A.) FOR SERVICING (Only in U.S.A.) 65 68 69 70 71 72 TIMER RECORDING 37 VCR Plus+ Timer Programming...................................................37 Manual Timer Programming.........................................................38 On-Disc Timer Programming .......................................................39 Check, Cancel And Change Programs ........................................41 Automatic Satellite Program Recording .......................................42 NAVIGATION 43 Library Database Navigation........................................................43 Basic Operation Of Original Information ......................................44 Edit Original Information...............................................................46 Basic Operation Of Play List Information .....................................47 Edit Play List Information .............................................................48 Edit Library Information ................................................................51 Playback With MP3/JPEG Navigation..........................................52 DISC INFORMATION EN 7 About Discs Recordable/Playable Discs You can use discs with the following logos for recording and playback. DVD-R/RW Discs It is only possible to use DVD-R discs which conform with DVD-R standard Version 2.0 or 2.1. It is only possible to use discs which conform with DVD-RW standard Version 1.1 or 1.2. Available in VR mode and Video mode. When a DVD-R/RW disc (Video mode) is finalized (A pg. 64), it can be played back on a standard DVD player as a DVD VIDEO disc. When a DVD-RW disc (VR mode) is finalized (A pg. 64), it can be played back on DVD player compatible with the VR mode of DVD-RW discs. Before finalizing ^ ^ it is possible to record on unrecorded areas of the disc, edit the disc title and program titles, and delete programs. It is impossible to record or edit DVD-R/RW discs recorded on other devices even if they have not been finalized. It is impossible to overwrite recorded areas of DVD-R discs. Available recording capacity does not increase even if a recorded program is deleted from a DVD-R disc. After finalizing ^ After a DVD-R/RW disc (Video mode) has been finalized, it is possible to play back the recorded programs (video and/or audio) on a standard DVD video player as a DVD VIDEO disc. Edited titles are displayed CONTENTS MENU as the "DVD menu" in PREV 81 Sister Princess ED2 14/11 0:55 PR12