User manual PALM TREO 180G - MACINTOSH EDITION

TreoTM 180g Communicator User Guide Macintosh Edition Copyright opy Copyright © 2001 Handspring, Inc. All Rights Reserved. Handspring, the Handspring logo, Treo, Blazer, and the Blazer logo are trademarks of Handspring, Inc., and may be registered in some jurisdictions. Portions copyright © 1998-2001 Palm, Inc. or its subsidiaries. All rights reserved. Palm OS, Graffiti, and HotSync are registered trademarks, and Palm and the HotSync logo are trademarks of Palm, Inc., and are used by Handspring under license. All other trademarks and trade names are the property of their respective owners. lim of Disclaimer and limitation of liability Handspring, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the use of this handbook. Handspring, Inc. and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of this software. Handspring, Inc. and its suppliers assume no responsibility for any damage or loss caused by deletion of data as a result of malfunction, dead battery, or repairs. Be sure to make backup copies of all important data on other media to protect against data loss. rra ens eem Warranty and License Agreement For warranty information and a copy of the End User License Agreement applicable to your Handspring product, please see the Handspring web site at http://support.handspring.com/esupport/forms/hsFileList.jsp?Type=Warranties. If you would like a copy of these materials mailed to you, or if you have any questions, please contact Handspring Customer Support. The information included on this web site sets forth Handspring's sole and complete warranty and software licensing obligations with respect to your Handspring product. Use of the product indicates your acceptance of the terms of the warranty and the End User License Agreement. do S oftware download available Wireless setup and desktop synchronization software are supplied on the Handspring CD-ROM disc. If you do not have access to a CD-ROM drive for your computer, you can download this software from www.handspring.com. Page 2 Macintosh Edition Contents Introduction to Your TreoTM 180g Communicator . . . . . . . . . . . . . . . . . . . . . . . . 11 Getting to know your communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 What is a Treo communicator? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Upgrade information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Treo components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Inserting the SIM card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Charging the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Turning your Treo on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Using the backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Using the stylus to get things done . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Elements of the communicator interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Moving around the screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Displaying online tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Customizing your communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Using the headset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Connecting the HotSync cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Using desktop software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Palm Desktop software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Using your communicator with another PIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Using an e-mail application with your communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Entering Data in Your Communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Using Graffiti writing to enter data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Writing Graffiti characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Graffiti tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 The Graffiti alphabet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Writing capital letters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Writing numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Writing punctuation marks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Writing symbols and extended characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Writing accented characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Accent strokes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Additional non-English characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Navigation strokes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Graffiti ShortCuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Using the onscreen keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Using your computer keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Importing data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Managing Your Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Using the Applications Launcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Opening applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Switching between applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Categorizing applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Changing the Applications Launcher display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Choosing preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Installing and removing applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Installing add-on applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Removing applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Removing Palm Desktop software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Assigning a password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Changing or deleting a password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Locking your communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Recovering from a forgotten password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Applications Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 PhoneBook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Date Book Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Blazer Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 SMS Messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 To Do List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Memo Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Calculator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 CityTime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Expense . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 SIM Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 SIM Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Common Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Using menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Choosing a menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Graffiti® menu commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Command toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Creating records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Page 4 Contents Editing records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Entering text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Edit menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Deleting records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Other ways to delete records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Purging records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Categorizing records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 System-defined and user-defined categories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Finding records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Looking up Contacts records in PhoneBook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Using Find . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Using Phone Number Lookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Sorting lists of records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Making records private . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Hiding and masking private records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Attaching notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Choosing fonts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Exchanging and updating data: HotSync operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Performing a HotSync operation for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Beaming information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Tips on beaming information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Application Specific Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 PhoneBook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Using the Speed Dial view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Using the Dial Pad view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Using the Contacts view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Using the Call History view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Using the Active Call view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Forwarding calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Other ways to make a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 PhoneBook menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Date Book Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 Scheduling an event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 Rescheduling an event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 Setting an alarm for an event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 Scheduling repeating or continuous events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 Changing the Date Book Plus view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 Working in Week View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 Working in Week View with Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 Working in Month View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 Working in Year View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 Contents Page 5 Working in List View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 Spotting event conflicts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Working with floating events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Working with To Do items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Using the Daily Journal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114 Using templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Date Book Plus menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 Blazer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 Viewing web pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 Working with bookmarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Blazer menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 SMS Messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 Enabling SMS and SMS Email . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 Receiving SMS messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 Viewing messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131 Replying to messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 Creating SMS messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 Creating a message signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Creating boilerplates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Copying and forwarding messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 Modifying messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136 Resending messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Sorting messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Deleting messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 SMS Messaging menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138 To Do List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Setting priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Setting a due date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 Assigning a category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 Checking off a To Do item . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 To Do Show Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 To Do List menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 Memo Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144 Reviewing memos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Memo Pad menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Calculator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Selecting the Calculator mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Using the Basic Calculator buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Displaying Recent Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Using the Advanced Calculator mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147 Using the Advanced Calculator buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Creating a custom view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154 Calculator menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 Page 6 Contents CityTime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 Setting your home city . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 Selecting remote cities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 Adding cities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157 CityTime menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157 Expense . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158 Changing the date of an Expense item . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159 Entering receipt details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159 Customizing the Currency pick list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160 Show Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161 Expense menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .162 SIM Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163 Copying entries from your Speed Dial list to your SIM card . . . . . . . . . . . . . . . . . . . . . . . .163 Copying entries from your SIM card to your Speed Dial list . . . . . . . . . . . . . . . . . . . . . . . .164 Deleting entries from your SIM card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .164 Dialing entries on your SIM card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165 SIM Book menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165 SIM Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166 Setting Preferences for Your Communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 Viewing Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167 Buttons Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168 Pen Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .168 HotSync Buttons Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169 Connection Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170 Connection Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170 Setting wireless modem configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171 Digitizer Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173 Formats Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173 Country default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173 Time, date, week start, and numbers formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .174 General Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .174 Auto-off delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .174 System, alarm, and game sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 75 Network Preferences and TCP/IP software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175 Selecting a service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175 Entering a user name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .176 Entering a password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .176 Selecting a connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177 Adding telephone settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178 Connecting to your service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180 Creating additional service templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180 Adding detailed information to a service template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180 Contents Page 7 Creating a login script . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 Deleting a service template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 Network Preferences menu commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 TCP/IP troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 Owner Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 Ringer Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 ShortCuts Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 Creating a ShortCut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187 Editing a ShortCut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188 Deleting a ShortCut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188 Advanced HotSync® Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189 Selecting HotSync setup options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189 Customizing HotSync application settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 IR HotSync operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192 Preparing your computer for infrared communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192 Configuring HotSync Manager for infrared communication . . . . . . . . . . . . . . . . . . . . . . . . 193 Performing an IR HotSync operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 Returning to cable HotSync operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194 Conducting a wireless HotSync operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 Preparing your computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 Preparing your communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 Selecting the conduits for a wireless HotSync operation . . . . . . . . . . . . . . . . . . . . . . . . . . 197 Performing a wireless HotSync operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 Creating a user profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .198 Maintaining Your Communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 Caring for your communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 Battery considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .201 Resetting your communicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 Performing a soft reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202 Performing a warm (or safe) reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 Performing a hard reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 Operating problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206 Tapping and writing problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 Wireless communication problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 Application problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .212 HotSync problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .213 Beaming problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .215 Password problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 Technical support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 Page 8 Contents Non-ASCII Characters for Login Scripts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 Use of ^char . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .217 Carriage return and line feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .217 Literal characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .217 Advanced Call Forwarding Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219 Forwarding calls when your communicator is busy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .219 Forwarding calls that you do not answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .220 Forwarding calls when your communicator is unreachable . . . . . . . . . . . . . . . . . . . . . . . . .220 General Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .220 Other Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 Limited Warranty and End User Software License Agreement . . . . . . . . . . . . . . . . . . . . .221 FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .221 Exposure To Radio Frequency Energy (SAR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .221 Canadian RFI Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .222 Safety and General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .222 Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .224 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Contents Page 9 Page 10 Contents Chapter 1 Introduction to Your TreoTM 180g Communicator This chapter explains the physical buttons and controls on your TreoTM 180g communicator, how to use your communicator for the first time, and how to install PalmTM Desktop software and the HotSync® Manager synchronization software so you can synchronize your communicator and your computer. Getting to know your communicator What is a Treo communicator? Your Treo communicator combines the power of a full-featured mobile phone, e-mail, SMS messaging, a Palm OS® handheld, and the Internet in one compact and indispensable device. With your Treo communicator, you can do everything you can do with your existing mobile phone with greater speed and ease. You can store thousands of numbers in your PhoneBook and up to 50 speed dial entries, and dial any of them with just a few taps on the screen. You can even set up a 3-way conference call by joining two calls and use the personal speakerphone for handsfree use without a headset attachment. Lighten your load. Everything you need is in one compact device. Your Treo communicator helps you stay in touch. With instant access to your e-mail, you can send and receive e-mail from anywhere, and use SMS messaging to exchange quick messages with other mobile phones on your network. The award-winning BlazerTM web browser gives you access to any site on the Internet--not just a few optimized for mobile access; now you can download directions, confirm flight reservations, find a restaurant, and check stock prices wherever you are. Everything you need to stay organized is close at hand on your communicator, including popular Palm OS applications such as Date Book Plus, PhoneBook, To Do List, Memo Pad and more. To make sure you don't lose any of this important information, you can synchronize your data with desktop software on your computer so you always have a backup copy. Chapter 1 Page 11 System requirements To install and operate Palm Desktop software and the HotSync Manager synchronization software, your computer system must meet the following requirements: Minimum requirements s s s s s s s Mac OS 8.5 or later with USB port (for USB HotSync cable) Apple Macintosh or compatible computer with a PowerPC processor 8 MB RAM (memory) minimum, 16 MB recommended 25 MB available hard disk space VGA monitor or better CD-ROM drive (you can also download Palm Desktop software from www.handspring.com) Mouse Upgrade information If you already own a Palm OS handheld, Handspring recommends that you install the version of Palm Desktop software that comes with your Treo communicator into the same folder as your current Palm Desktop software. When you install the new version in the same folder as the previous version, all your data is preserved. If you use another personal information manager (PIM), you still need to install Palm Desktop software in order to update the HotSync Manager on your computer. You perform HotSync operations in exactly the same way, so you can quickly synchronize your old data with your new communicator. To upgrade: 1. Synchronize your old communicator with your old Palm Desktop software. This ensures that the latest information from your communicator is on your desktop computer. 2. (Optional) To ensure against any data loss, go to the folder that stores Palm Desktop software (this is usually the Handspring or Palm folder), copy (do not move) your user name folder, and store the copy outside the Palm Desktop software folder. 3. Follow the installation instructions that begin on page 24. Be sure to install the new software in the same folder as the old software. 4. Connect your new communicator to the HotSync cable and press the HotSync button on the cable. If the User dialog box appears, select your user name. 5. Compare the applications on your old handheld and your new communicator. 6. Beam any third party applications that did not transfer from your old handheld to your new communicator, or install them from the original files. Page 12 Introduction to Your TreoTM 180g Communicator Each device must have a unique name After you complete the upgrade process described above, you have two devices with the same name. This is an undesirable situation. Each device must have a unique name in order to prevent unexpected results during HotSync operations and other complications. We strongly recommend that you perform a hard reset on your old handheld. See page 203 for details. A hard reset not only erases all data from the old handheld; it also erases the name and makes that handheld a clean slate, ready to receive a new name. The next time you perform a HotSync operation with this old handheld, you are asked to give it a name. Be sure to give it a unique name. Treo components Locating front panel controls Speaker Screen Headset jack Graffiti® writing area Jog rocker Contrast control Microphone Scroll buttons Application buttons Speaker Headset jack Functions as the earpiece on your Treo. Enables you to connect a hands-free headset for use with the wireless features. Use only headsets that are compatible with your communicator. Chapter 1 Page 13 Jog rocker Enables you to navigate on your communicator with just one hand. You can use the jog rocker as an alternate method to perform a variety of tasks, such as adjusting the call volume level on your phone. The jog rocker functions change based on whether your communicator's wireless mode is on or off and which application you are using. To use the jog rocker, roll the dial up or down, press it in and release it, or press and hold it. Contrast Control Opens the contrast control screen when you tap this icon. The contrast control screen enables you to adjust the appearance of your communicator screen for the clearest screen display. Depending on the lighting conditions or temperature of the environment where you use your communicator, you may need to adjust the contrast. To adjust the contrast, drag the slider or tap the ends of the contrast bar to increase or decrease the contrast. To fine tune the contrast, press the scroll buttons on the front panel of your communicator. Microphone Scroll buttons Functions as the mouthpiece when you use the wireless phone features of your Treo. Displays text and other information that extends beyond the area of the communicator screen. Pressing the bottom scroll button scrolls down to view information below the viewing area, and pressing the top scroll button scrolls up to view the information above the viewing area. The scroll buttons also enable you to navigate between records in an application and to adjust the volume during a call. Activates the applications that correspond to the icons on the buttons: PhoneBook, Date Book Plus, Blazer (or another web browser installed by your wireless service provider), and SMS Messaging. See page 168 for details on reassigning these buttons to activate any application on your communicator. Tip: If your communicator is turned off, pressing any application button turns on your communicator and opens the corresponding application. Application buttons Graffiti writing area Communicator screen The area where you write letters and numbers using the Graffiti alphabet. See Chapter 2 to learn how to write Graffiti characters. Displays the applications and information stored in your communicator. It is touch-sensitive and responds to the stylus. Page 14 Introduction to Your TreoTM 180g Communicator Locating top panel controls Antenna Power button IR port Stylus LED Ringer switch Antenna Stylus Receives and sends wireless communication signals. The antenna does not telescope out of your communicator. Serves as the writing instrument used to enter data in your communicator. To use the stylus, slide the stylus out of the slot, and hold it as you would a pen or pencil. Turns your communicator and wireless mode on and off, and controls the backlight. See page 18 for details. Uses infrared technology to transmit data to and receive data from other Palm OS devices. See the section that begins on page 77 for details. You can also use the IR port to update the information between your communicator and computer using HotSync technology. See the section that begins on page 192 for details. Provides status information for your Treo based on the color of the light and the blink state. No light: Wireless mode off Solid: Connected to travel charger Green = Fully charged Red = Charging Blinking: Wireless mode on Green = In coverage area Red = Out of coverage area Double-blink red: Low battery Power button IR port LED Ringer switch Controls the ringer setting. See page 187 for details on changing the settings. Note: Silencing the ringer also turns off all system sounds, including alarms. If the vibrate option is turned on in the Ringer Preferences screen, ring tones and alarms are replaced with a vibrate motion. Chapter 1 Page 15 Locating back panel components Reset button SIM card door Charger and USB/serial connector SIM card door Reset button Charger and USB/serial connector Secures your SIM (Subscriber Identity Module) card in your phone. Under normal use, you should not have to use the reset button. See Appendix A for information about when and how to use the reset button. The connector that connects your communicator to the travel charger and HotSync cable. The HotSync cable connects to a USB port or serial port on your computer and enables you to synchronize the information between your communicator and computer using HotSync technology. Inserting the SIM card The SIM card is a small rectangular plastic piece that contains your phone number and account information. It is included with your wireless service provider's documentation and is often referred to as a "smartcard." If a SIM card did not come with your communicator, your wireless service provider will provide you with one when you subscribe to their service. You must insert your SIM card into your communicator before you can use it for wireless communications. Since calls are billed to your phone number, you can, however, move your SIM card to any phone that uses a SIM card, and the calls will be billed to your account. To insert the SIM card: 1. Remove the SIM door. 2. With the contacts face-up, align the notch on the SIM card with the notch on the door and insert the SIM card into the slot on the door. SIM door SIM card Notch 3. Replace the SIM door. Page 16 Introduction to Your TreoTM 180g Communicator Charging the battery To use your communicator, you must connect the travel charger or the HotSync cable and charge the battery. When you're near your computer, connect your communicator to the HotSync cable with the travel charger connected to a wall outlet as shown in the section that begins on page 23. When travelling, connect the travel charger cable directly to your communicator as shown in this section. When wireless mode is on, a fully charged battery provides approximately 2.5 hours of talk time or 60 hours of standby time. When wireless mode is off, a fully charged battery provides approximately three weeks of use in handheld mode. If the battery drains to the point where your communicator does not turn on, it stores your data safely for about three days. Therefore, we recommend that you charge the battery daily to avoid potential data loss. See Appendix A for tips on extending the life of the battery. To charge the battery with the travel charger: 1. Plug the travel charger into a wall outlet. 2. With the word "UP" facing up (as shown), connect the travel charger cable to the charger connector on the bottom of your communicator. LED Tip: The LED is solid red while your communicator charges. When the LED turns solid green, your communicator is charged. It takes approximately 90 minutes to charge a fully drained battery. Chapter 1 Page 17 Turning your Treo on and off Your Treo communicator has two operating modes: a handheld mode and a wireless mode. You can turn the handheld mode and the wireless mode on and off independent of each other. When you turn on the handheld mode, you can use organizer applications such as Date Book Plus and To Do List. When you turn on the wireless mode, you can make or receive calls. You can also turn both modes on at the same time. When both the handheld and wireless modes are on, you can use the organizer applications as well as send and receive calls. To turn handheld mode on and off, do any of the following: s s s s Open the lid to turn it on, or close the lid to turn it off. Press the power button. Press and release the jog rocker. Press any application button on the front of your communicator. To turn wireless mode on and off: s Press and hold the power button until you hear the confirmation tones to turn wireless mode on and off. The ascending tone indicates wireless mode is now on and the descending tone indicates wireless mode is now off. Using the backlight If you have difficulty seeing the information on your communicator in dark environments, you can use the backlight to illuminate the images on the screen. Note: If you have difficulty seeing the screen in well-lit environments, adjust the contrast instead of using the backlight. See page 13 for details. To turn the backlight on and off: s Press the power button twice in quick succession. Backlight tips: s s s You can assign the full-screen pen stroke to activate the backlight. See page 168 for details. The backlight turns on automatically when an incoming call "wakes up" your communicator. The backlight also turns off automatically (after a period of inactivity) with the Auto-off feature. See page 174 for details. Page 18 Introduction to Your TreoTM 180g Communicator Using the stylus to get things done Like using a mouse to click elements on a computer screen, using the stylus to tap elements on your communicator screen is the basic action to get things done on your communicator. The first time you start your communicator, setup instructions appear on the screen. These instructions include a calibration screen, or digitizer. Calibration aligns the internal circuitry of your communicator with its touch-sensitive screen so that when you tap an element on the screen, the communicator can detect exactly which task you want to perform. Important: Always use the point of the stylus for tapping or making strokes on the communicator screen. Never use an actual pen, pencil, or other sharp object to write on the communicator screen. With your communicator turned on, you can tap the communicator screen to perform many operations, such as the following: s s s s s Open applications Choose menu commands Initiate a global Find operation Select options in dialog boxes Open the onscreen keyboards Just as you can drag the mouse to select text or move objects on your computer, you can also drag the stylus to select text. You can also use the stylus to drag the slider of any scroll bar. Chapter 1 Page 19 Elements of the communicator interface Menu bar Pick list Check box Icons Command buttons Menu bar Command buttons Icons A set of commands that are specific to the application. Not all applications have a menu bar. Tap a button to perform a command. Command buttons appear in dialog boxes and at the bottom of application screens. Tap the icons to open applications anywhere in your data . , menus , Calculator , and to find text abc 123 With the cursor in an input field, tap the "abc" dot to activate the alphabetic keyboard. With the cursor in an input field, tap the "123" dot to activate the numeric keyboard. Check box When a check mark appears in a check box, the corresponding option is active. If a check box is empty, tapping it inserts a check mark. If a check box is checked, tapping it removes the check mark. Pick list Tap the arrow to display a list of choices, and then tap an item in the list to select it. Previous/next arrows Scroll bar Previous/ next arrows Scroll bar Tap the up and down arrows to display the previous and next page of information; tap the left and right arrows to display the previous and next record. Drag the slider, or tap the top or bottom arrow, to scroll the display one line at a time. To scroll to the previous page, tap the scroll bar just above the slider. To scroll to the next page, tap the scroll bar just below the slider. You can also scroll to the previous and next pages by pressing the scroll buttons on the front panel of your communicator. Page 20 Introduction to Your TreoTM 180g Communicator Moving around the screen You can move between entry fields, pick lists, check boxes, and other options by using the stylus, the scroll buttons, or the jog rocker. To move around the screen do one of the following: s s s Tap an item with the stylus. Press the scroll buttons to scroll through the items on the screen. Roll the jog rocker up or down to scroll through the items on the screen. Displaying online tips Many of the dialog boxes that appear on your communicator contain an online Tips icon in the upper-right corner. Online tips anticipate questions you have in a dialog box, provide shortcuts for using the dialog box, or give you other useful information. To display an online tip: 1. Tap the Tips icon . 2. After you review the tip, tap Done. Customizing your communicator You can customize your communicator by using the Preferences application. You can enter personal information such as your name and address; change the time and date; view different date and time formats when you travel; turn off sounds; configure your communicator to work with a modem or network, and select ringer settings. See Chapter 7 for more information on customizing your communicator. To open the Preferences screens: 1. Tap the Applications icon 2. Tap the Preferences icon . . 3. Tap the category pick list in the upper-right corner of the screen. 4. Tap the Preferences category you want to view. The following procedures for setting the time and date give you an example of how to customize your communicator. You make changes to the time and date in General preferences. Chapter 1 Page 21 To set the current time: 1. Tap the Set Time box. Tap here 2. Tap the up or down arrows to change the hour. 3. Tap each minute number, and then tap the arrows to change them. 4. Tap AM or PM. Note: 5. Tap OK. Your communicator can also display time based on a 24-hour clock. See page 173 for details. To set the current date: 1. Tap the Set Date box. 2. Tap the arrows to select the current year. Tap arrows to select year Tap to select month Tap to select date 3. Tap the current month. 4. Tap the current date. Page 22 Introduction to Your TreoTM 180g Communicator Using the headset You can connect a headset for hands-free operation. Your Treo is compatible with the included headset and other headsets listed at www.handspring.com. If you need to use your phone while driving and this is permitted in your area, we recommend using a headset. Note: Treo is not compatible with three-pin (also called three-pole) style headsets. You can determine whether a headset is a three-pin headset by counting the number of silver rings on the headset pin. A three-pin headset has three rings. To use the headset: 1. Connect the headset plug to the headset jack on the side of your communicator. Speaker Microphone Headset button 2. Place the speaker in your ear. 3. Press the headset button to perform any of the following functions: s s s s Answer an incoming call (including an incoming call waiting call). Switch between two active calls. Place the second call on hold when you have two active calls. Hang up an active call. Connecting the HotSync cable The HotSync cable that comes with your Treo enables you to charge your communicator battery and to synchronize the information on your communicator using HotSync technology. To connect the HotSync cable: 1. Connect the travel charger cable to the short end of the Hotsync cable. Be sure to match the sides of the connectors labeled "UP." 2. Connect the USB HotSync cable to a USB port on your computer. 3. Connect the long end of the HotSync cable to your communicator with the button facing up. Chapter 1 Page 23 USB cable and port Note: If you are unsure about the exact location of the USB port on your computer, refer to the manual supplied with the computer. 4. Plug the travel charger into a wall outlet. Tip: The travel charger does not need to be plugged into a wall outlet to perform a HotSync operation. However, if you want to use the HotSync cable to charge your Treo communicator, you must plug the travel charger into a wall outlet. Using desktop software When you use desktop software with HotSync technology, you can do any of the following: s Work with your communicator applications on your computer. Most desktop software applications duplicate many of the applications on your communicator, so you can view, enter, and modify most of the data stored on your communicator. Back up and synchronize data between your communicator and your computer. Synchronization is a one-step procedure that ensures that changes you make on your communicator or desktop software appear in both places. See the section that begins on page 76 for details. Configure the wireless data features of your Treo. Import and export data, so you can easily transfer data from other desktop applications into many of your applications. See the section that begins on page 35 for details. Print data from your desktop software on any printer. s s s s Palm Desktop software Your communicator comes with Palm Desktop software. Palm Desktop software includes many of the same applications as your communicator: Daily Calendar (Date Book Plus), Contact List (the Contacts view in PhoneBook), Task (To Do List), and Note (Memo Pad). Page 24 Introduction to Your TreoTM 180g Communicator The following instructions guide you through installing Palm Desktop software. After installation, refer to the online Help in Palm Desktop software for information about how to use the software. Note: You must install the software that comes with your Treo communicator even if you already installed Palm Desktop software for a previous Palm OS handheld. To ensure a safe and uninterrupted installation of Palm Desktop software, please do not simply copy the Palm Desktop software files to your computer's hard disk. You must use the installer to place the files in their proper locations and to decompress the files. To install Palm Desktop software: 1. Connect the HotSync cable. See page 23 for instructions. 2. Exit any open programs, including those that run at startup, and disable any virus-scanning software. 3. Insert the Handspring CD-ROM into the computer's CD-ROM drive. 4. Double-click the Handspring CD icon on the desktop. 5. Double-click the Installer icon to begin the installation process. 6. Follow the onscreen instructions to complete the installation and to configure your Treo for wireless data communication. When the set up process is done, the installation screen closes automatically. Using your communicator with another PIM If you prefer to use another personal information manager (PIM), you can use it if third-party connection software, called a conduit, is available for your PIM. You must install the software that came with your Treo communicator along with the conduit for your PIM to synchronize the data between your communicator and your PIM. For information on conduit software, go to this web site: www.handspring.com. Using an e-mail application with your communicator Your communicator comes with the One-Touch MailTM by JP Mobile e-mail application. Note: To use a wireless e-mail application, your wireless service provider must support data services and it must be part of your service package (some wireless service providers may require you to sign up for data services separately). You must also have an account established with an ISP (Internet Service Provider). Many wireless service providers also provide ISP services. If ISP information is available from your wireless service provider when you configure your wireless communication settings with the Handspring CD-ROM, the installation program sets up your communicator for use with that provider. One-Touch Mail One-Touch Mail is a wireless e-mail application that enables you to access your ISP (POP3 account) e-mail directly from your communicator. You may also be able to use One-Touch Mail to access your corporate e-mail; contact your System Administrator for assistance. Chapter 1 Page 25 To install One-Touch Mail, do one of the following: s Select the One-Touch Mail option when you configure the wireless communication features using the Handspring CD-ROM. If you already installed the desktop software from the Handspring CD-ROM but didn't install this application, double-click the Configure Your Treo icon in the Handspring folder. s Page 26 Introduction to Your TreoTM 180g Communicator Chapter 2 Entering Data in Your Communicator This chapter explains how to enter data into your TreoTM 180g communicator using each of the following methods: s s s s Using Graffiti® writing Using the onscreen keyboard Using your computer keyboard Importing data Using Graffiti writing to enter data Your communicator includes Graffiti writing software as the primary system for entering text and numbers. With Graffiti writing, you write simple strokes with the stylus and they are instantly recognized as letters or numbers. This section shows you how to write letters, numbers, punctuation, and symbols as well as some Graffiti tips and tricks. Writing Graffiti characters Most people find they can enter text quickly and accurately with only minutes of practice. Graffiti writing includes any character you can type on a standard keyboard. The Graffiti strokes closely resemble the uppercase letters of the regular alphabet, which makes Graffiti writing easy to learn. There are four basic concepts for success with Graffiti writing: s If you draw the character shape exactly as shown in the tables later in this chapter (like the shapes shown in the following diagram), you achieve 100% accuracy. s The heavy dot on each shape shows where to begin the stroke. Certain characters have similar shapes, but different beginning and end points. Always begin the stroke at the heavy dot (you should not create the heavy dot; it is only there to show you where to begin the stroke). Most characters require only a single stroke. When you lift the stylus from the Graffiti writing area, your communicator recognizes and displays the text character immediately. To accomplish single strokes, some Graffiti strokes are portions of the regular alphabet equivalents. s Chapter 2 Page 27 s The Graffiti writing area is divided into two parts: one for writing the letters of the alphabet and one for writing numbers. The small division marks at the top and bottom of the Graffiti writing area indicate the two separate areas. Write letters here Write numbers here Division marks To write Graffiti letters: 1. Tap the screen where you want your text to go. Note: You need to tap above the Graffiti writing area, and must see a blinking cursor before you write the text. 2. Use the tables on the following pages to find the stroke shape for the letter you want to create. For example, the stroke shown below creates the letter "n." Note: There are two different stroke shapes available for some letters. For these letters, choose the one that's easiest for you. Lift stylus here Start stroke at heavy dot As you'll see later, you use the same shape to create both the uppercase and lowercase version of a letter. 3. Position the stylus in the left-hand side of the Graffiti writing area. 4. Start your stroke at the heavy dot and draw the stroke shape as it appears in the tables. 5. Lift the stylus from the screen at the end of the stroke shape. That's all there is to it! When you lift the stylus from the screen, your communicator recognizes your stroke immediately and prints the letter on the screen next to the cursor. As soon as you lift the stylus from the screen, you can begin the stroke for the next character you want to write. Important: You must begin the character strokes in the Graffiti writing area. If you do not make Graffiti strokes in the Graffiti writing area, your communicator does not recognize them as text characters. Page 28 Entering Data in Your Communicator Graffiti tips When using Graffiti writing, keep these tips in mind: s Accuracy improves when you write large characters. You should draw strokes that nearly fill the Graffiti writing area. To delete characters, simply set the cursor to the right of the character you want to delete and make the backspace stroke (a line from right to left) in the Graffiti writing area. Write at natural speed. Writing too slowly can generate recognition errors. Do not write on a slant. Vertical strokes should be parallel to the sides of the Graffiti writing area. Press firmly. s s s s The Graffiti alphabet Letter A B Strokes Letter K L Strokes Letter U V Strokes C D E F G H I J M N O P Q R S T W X Y Z Space Carriage Return Back Space Period tap twice Chapter 2 Page 29 Writing capital letters You make capital letters with the same stroke shapes as the basic alphabet characters. To make capital letters, you must first "shift" to caps -- just as you press the Shift key on a keyboard -- and then write the character strokes. Note: Graffiti writing includes a feature that automatically capitalizes the first letter when you create a new sentence or a new record (by tapping New or a blank line). To draw the first letter of a word as a capital letter: s Use the Caps Shift stroke: Caps Shift Tip: When Caps Shift is active, an "up arrow" symbol appears in the lower-right corner of the communicator screen. If you accidentally activate Caps Shift, backspace will cancel it. Caps Shift To enter only capital letters (Caps Lock): s Use the Caps Lock stroke: Caps Lock Tip: When Caps Lock is active, an underlined "up arrow" symbol appears in the lower-right corner of the communicator screen. To return to lowercase, make the Caps Shift stroke. Caps Lock Writing numbers Writing numbers with Graffiti writing is similar to writing letters of the alphabet, except that you make the character strokes on the right-hand side (numbers side) of the Graffiti writing area. Number 0 1 Strokes Number 5 6 Strokes Page 30 Entering Data in Your Communicator 2 3 4 7 8 9 Writing punctuation marks Graffiti writing can create any punctuation symbol that you can enter from a standard keyboard. All punctuation marks begin with a single tap on the Graffiti writing area. When you make this tap, you activate Punctuation Shift and a dot appears to show it is active. The next stroke you make with the stylus creates a punctuation mark. Punctuation Shift Note: When Punctuation Shift is active, you can make a symbol stroke anywhere in the Graffiti writing area (the letters or numbers side). Symbol Period . Comma , Apostrophe ' Question ? Exclamation ! Stroke Symbol Dash -- Left Paren ( Right Paren ) Slash / Dollar $ Stroke Additional Graffiti punctuation @ # % ^ &* < > ­ + = | \ { } [ ] ~ ` ; : " tab Chapter 2 Page 31 Writing symbols and extended characters All symbols and extended characters begin with the stroke in the Graffiti writing area of your communicator: Symbol Shift When the Symbol Shift is active, a slanted shift symbol appears in the lower-right corner of the screen. The next stroke that you make creates the symbol or extended character. Symbol Shift Writing accented characters To create accented characters, draw the stroke normally used to create the letter, followed by an accent stroke. Graffiti writing then adds the accent to the letter. For example, the following diagram shows the strokes required to draw an accented "e." =e Accent strokes a a a a a a Using these accent strokes, you can write the following accented letters: àáâãäåèéêìíîïòóôõöùúûüÿýñ Page 32 Entering Data in Your Communicator Additional non-English characters You can write the following characters in the lowercase alphabet mode without any special punctuation or shifting: c ae Note: You must write these non-English characters in the left side of the Graffiti writing area. Navigation strokes In addition to character symbols, Graffiti writing includes special strokes that you can use to navigate within text or fields in your applications. Command Move cursor right Move cursor left Previous field (Contacts view in PhoneBook only) Next Field (Contacts view in PhoneBook only) Open Contact Record (Contacts view in PhoneBook only) Stroke Graffiti ShortCuts Graffiti ShortCuts make entering commonly used words or phrases quick and easy. ShortCuts are similar to the Glossary or Autotext features of some word processors. Graffiti writing comes with several predefined ShortCuts, and you can also create your own. Each ShortCut can represent up to 45 characters. For example, you might create a ShortCut for your name, or for the header of a memo. See page 187 to learn about creating your own ShortCuts. To use a ShortCut, draw the ShortCut stroke followed by the ShortCut characters. When you draw the ShortCut stroke, the ShortCut symbol appears by the cursor to show that you are in ShortCut mode. ShortCut Chapter 2 Page 33 Your communicator includes the following predefined Graffiti ShortCuts: Entry Date stamp Time stamp Date / time stamp Meeting Breakfast Lunch Dinner ShortCut ds ts dts me br lu di Using the onscreen keyboard You can open the onscreen keyboard anytime you need to enter text or numbers on your communicator. Note that you cannot enter Graffiti characters while using the onscreen keyboard. To use the onscreen keyboard: 1. Open any application (such as Memo Pad). 2. Tap any record, or tap New. 3. Tap "abc" to open the alphabetic keyboard, or tap "123" to open the numeric keyboard. Tap here for alpha keyboard Tap here for numeric keyboard 4. Tap the characters to enter text and numbers. Page 34 Entering Data in Your Communicator Tab Caps lock Caps shift Tap here to display alphabetic keyboard Backspace Carriage return Tap here to display numeric keyboard Tap here to display international keyboard Note: The onscreen keyboard also includes a dialog box for international characters. You can switch among the three dialogs at any time to enter the exact text you need. 5. After you finish, tap Done to close the onscreen keyboard and place the text in the record. Using your computer keyboard Many of the applications on your communicator are available in Palm Desktop software and in most Personal Information Manager (PIM) applications. If you have a lot of data to enter, or prefer to use the computer keyboard, you can use PalmTM Desktop software, or any supported PIM such as Microsoft Outlook, to enter information. You can then perform a HotSync® operation to synchronize the information on your computer with the information on your communicator. See the section that begins on page 76 for details on HotSync operations. Refer to Palm Desktop online Help or the documentation that came with your PIM software for more information on entering data on your computer. Importing data If you have data stored in computer applications such as spreadsheets and databases, you can transfer the data to your Treo communicator without having to key it in manually. Save the data in one of the file formats listed below, import it into Palm Desktop software, and then perform a HotSync operation to transfer the data to your communicator. You can import data from any of the following PIM (personal information manager) products. s s s s s Address Book Plus DateBook Pro DayMaker Dynodex Meeting Maker Chapter 2 Page 35 s s s s Now Contact Now Up-to-Date QuickDex TouchBase Pro Palm Desktop software can open Claris Organizer files directly; you do not need to import them. To import data from PIM product files, you must export and save the entire file in text format first. You can import fields from TouchBase Pro, DateBook Pro, DayMaker, and QuickDex files in the proper order. You might have to adjust the field order of other PIM product files you import. You can also import data from a FileMaker Pro database or a ClarisWorks database. In FileMaker Pro, be sure to export the database to the Tab-Separated Text file type. In ClarisWorks, be sure to save the database in ASCII text format and give it a different name so you don't overwrite the original file. You can import data from a Newton that uses Newton Operating System 1.0. Simply use the Newton Connection Kit to export data from the Newton Names file, Date Book Calendar file, and Notepad, and then import the resulting files into PalmTM Desktop software. The Newton Connection Kit does not work with Newton Operating System 2.0. To import data: 1. Export a text file from the other product. 2. Open Palm Desktop software. 3. From the File menu, choose Import. 4. Select the file you want to import. 5. Click Open. 6. In the Import dialog box, check each field name to be sure the correct data moves into the correct fields. To change the order of a field in the file you're importing into, move the pointer over a field name in the Fields In list. When the pointer changes to double arrow, drag the name to a new location. To prevent information from being imported into a field, click the arrow between field names. The arrow changes to a dotted line. To view the information in the file you're importing from, click the Scan Data arrows to see the information in each record. 7. From the Fields pop-up menu, choose the appropriate field. 8. From the Delimiters pop-up menu, choose the appropriate delimiter. The field and delimiter are set automatically if you are importing a Claris Organizer, TouchBase Pro, DateBook Pro, DayMaker, or QuickDex file. 9. Click OK. Page 36 Entering Data in Your Communicator Chapter 3 Managing Your Applications This chapter explains how to switch between applications on your TreoTM 180g communicator, how to change application settings so they are personalized to your work methods, and how to categorize applications so you view them in related groups. Using the Applications Launcher Your communicator is equipped with a variety of applications. All the applications installed on your communicator appear in the Applications Launcher. Opening applications You can use the Applications Launcher to open any application installed on your communicator. You can also open the four main applications -- PhoneBook, Date Book Plus, BlazerTM (or another web browser installed by your wireless service provider), and SMS Messaging -- with the application buttons on the front panel of your communicator. Tip: When you press an application button on the front panel of your communicator, you have instant access to the selected application. You don't even need to turn on your communicator first. In addition to providing a way for you to open applications, the Applications Launcher displays the current time, battery level, wireless signal status, and application category. To open an application: 1. Tap the Applications icon . 2. Tap the icon of the application that you want to open. To see additional applications, tap the scroll bar. Tip: To find an application quickly, you can write the Graffiti character for the first letter of its name. The Applications Launcher scrolls to the first application with a name that begins with that letter. You can also create categories and organize your applications by category. See page 38 for details. Page 37 Chapter 3 Switching between applications When working in any application, tap the Applications icon or press an application button on the front panel of your communicator to switch to another application. Your communicator automatically saves your work in the current application and displays it when you return to that application. Categorizing applications The category feature enables you to manage the number of application icons that appear onscreen in the Applications Launcher. You can assign an application to a category and then display a single category or all your applications. To categorize an application: 1. Tap the Applications icon 2. Tap the Menu icon . . 3. Tap App, and then tap Category. 4. Tap the pick list next to each application to select a category. Tip: To create a new category, tap Edit Categories from the pick list. Tap New, enter the category name, and then tap OK to add the category. Tap OK. 5. Tap Done. To display applications by category: 1. Tap the Applications icon 2. Do one of the following: Tap the Applications icon repeatedly to cycle through all your categories. Tap the pick list in the upper-right corner of the screen and select the category you want to display. . Page 38 Managing Your Applications Changing the Applications Launcher display By default, the Applications Launcher displays each application as an icon. As an alternative, you can choose to show a list of applications. You can also choose to view the same category of applications each time you open the Applications Launcher. To change the Applications Launcher display: 1. Tap the Applications icon 2. Tap the Menu icon . . 3. Tap Options, and then tap Preferences. 4. Tap the View By pick list and select List. 5. Tap OK. To open the Applications Launcher to the last opened category: 1. Tap the Applications icon 2. Tap the Menu icon . . 3. Tap Options, and then tap Preferences. 4. Tap the Remember Last Category check box to select it. 5. Tap OK. Choosing preferences You can set options that affect an entire application in the application's Preferences dialog box. To change preferences for an application: 1. Open an application. 2. Tap the Menu icon . 3. Tap Options, and then tap Preferences. Note: Not all applications have a Preferences command. Chapter 3 Page 39 4. Make changes to the settings. 5. Tap OK. Installing and removing applications This section explains how to install and remove applications on your communicator and how to remove PalmTM Desktop software from your computer. Installing add-on applications Your communicator comes with the PhoneBook, Date Book Plus, Blazer (or another web browser installed by your wireless service provider), SMS Messaging, To Do List, Memo Pad, Expense, Calculator, CityTime, SIM Book, and SIM Services applications installed and ready to use. The Handspring CD-ROM also includes e-mail applications which you can install when you configure the wireless portion of your communicator with the CD-ROM. You can also install additional applications on your communicator, such as business applications, games, and other software. The Install Handheld Files dialog box makes it easy to install software on your communicator during a HotSync® operation. There are a variety of third-party applications available for devices that use Palm OS software. To learn more about these applications, go to the web site: www.handspring.com. When you download an add-on application from the Internet, it is probably in a compressed format such as a .zip or .sit file. If you have a decompression utility on your computer, use it to decompress the .prc and .pdb files inside the compressed file. If you do not have a decompression utility, search the Internet using phrases like 'zip decompression' or 'how to unzip'. This will lead you to various third-party utilities that you can use to decompress any kind of compressed or downloaded file--not just add-ons for your communicator. After you install the utility, you are ready to decompress the add-on application files that you downloaded. Note: Any applications that you install on your communicator resides in RAM memory; you can delete them at any time. To install add-on software on your communicator: 1. Copy or download the application you want to install into the add-on folder in your Palm folder on your computer. Note: If the software you download is compressed, you need to decompress it into this folder. If you prefer to place the application into another folder, you need to navigate to that folder before you complete step 5. 2. Double-click the Palm Desktop icon on your desktop. 3. From the HotSync menu, choose Install Handheld Files. Tip: You can also access the Install Handheld Files dialog box by double-clicking any file with a PRC file extension. Page 40 Managing Your Applications 4. From the User pop-menu, select the name that corresponds to your Treo communicator. 5. Click Add to List. 6. Select the application(s) you want to install on your communicator. 7. Click Add File. Note: Review the list of applications you selected in the Install Handheld Files dialog box. If you do not want to install an application, select it, and then click Remove From List. (This does not remove the application from your computer; it simply removes it from the list of applications to install.) 8. Close the Install Handheld Files dialog box. 9. Perform a HotSync operation to install the application(s) you selected in step 6. See the section that begins on page 76 for details. Tip: You can also install an application by simply double-clicking the application's icon. Page 41 Chapter 3 Removing applications In the event that you run out of memory or decide that you no longer need an application you installed, you can remove applications from your communicator. You can remove only add-on applications, patches, and extensions that you install; you cannot remove the applications that reside in the ROM portion of your communicator. To remove an add-on application: 1. Tap the Applications icon 2. Tap the Menu icon . . 3. Tap App, and then tap Delete. 4. Tap the application that you want to remove.