User manual YAESU FT-2000 - MENU MODE LIST

MENU MODE The Menu system of the FT-2000 provides extensive customization capability, so you can set up your transceiver just the way you want to operate it. The Menu items are grouped by general utilization category, and are numbered from "001 AGc 001 DLY" EMRGNCY." FST DLY to "149 tGEn EMRGNCY 149 USING THE MENU 1. Press the [MENU] button momentarily, to engage the Menu mode. The Main (VFO-A) frequency display will show the Menu Number and Menu Group name, while the Sub (VFO-B) frequency display will show the Menu item; the Multi-Display window shows the current setting of the currently-selected Menu item. 2. Rotate the Main Tuning Dial knob to select the Menu item you wish to work on. 3. Rotate the [SUB VFO-B] knob to change the current setting of the selected Menu item. ADVICE: Press the [CLEAR] button momentarily to reset the selected Menu item to the factory default value. 4. When you have finished making your adjustments, press and hold in the [MENU] button for two seconds to save the new setting and exit to normal operation. If you only momentarily press the [MENU] button, the new settings will not be retained. [CLEAR] Button [MENU] Button Main Tuning Dial Knob [SUB VFO-B] Knob Menu Number Menu Group Name Menu Item Menu Setting Menu Mode Reset You may reset all the Menu settings to their original factory defaults, if desired. 1. Turn the front panel [POWER] switch off. 2. Press and hold in the [MENU] button, and while holding it in, press the [POWER] switch to turn the transceiver back on. Now release the [MENU] button. Page 108 FT-2000 OPERATING MANUAL MENU MODE GROUP AGC AGC AGC AGC AGC AGC DISPLAY DISPLAY DISPLAY DISPLAY DISPLAY DISPLAY DISPLAY DISPLAY DISPLAY DVS DVS KEYER KEYER KEYER KEYER KEYER KEYER KEYER KEYER GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL S IF SFT S IF SFT S IF SFT S IF SFT S IF SFT S IF SFT S IF SFT S IF SFT MODE-AM MODE-AM NO. 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 MENU FUNCTION AGc FST DLY AGc FST HLD AGc MID DLY AGc MID HLD AGc SLW DLY AGc SLW HLD diSP COLOR diSP DIM MTR diSP DIM VFD diSP BAR SEL diSP PK HLD diSP RTR STU diSP RTR ADJ diSP QMB MKR diSP LVL IND dUS RX LVL dUS TX LVL tEy BEACON tEy NUM STL tEy CONTEST tEy CW MEM1 tEy CW MEM2 tEy CW MEM3 tEy CW MEM4 tEy CW MEM5 GEnE ANT SEL GEnE BEP LVL GEnE CAT BPS GEnE CAT TOT GEnE CAT RTS GEnE CAT IND GEnE MEM GRP GEnE Q SPLIT GEnE TRACK GEnE TX TOT GEnE TRV SET GEnE T DIAL GEnE SNB LVL GEnE SUB FIL GEnE MIC SCN GEnE SCN RSM GEnE ANTIVOX GEnE FRQ ADJ S-iF LSB SFT S-iF USB SFT S-iF CWL SFT S-iF CWU SFT S-iF RTTY S-iF RTTY-R S-iF PKT-LSB S-iF PKT-USB A3E MICGAIN A3E MIC SEL AVAILABLE VALUES 20 ~ 4000 msec (20 msec/step) 0 ~ 2000 msec (20 msec/step) 20 ~ 4000 msec (20 msec/step) 0 ~ 2000 msec (20 msec/step) 20 ~ 4000 msec (20 msec/step) 0 ~ 2000 msec (20 msec/step) bL1 / bL2 / bL3 / ub1 / ub2 0 ~ 15 0~7 CLAr / C-tn / u-tn OFF / 0.5 / 1.0 / 2.0 sec 0 / 90 / 180 / 270° ­30° ~ 0° (2°/step) On / OFF PI / SP / CO / nO / dn / Cd / Ud / rP / nG / Pr / SH / UI 0 ~ 100 0 ~ 100 OFF / 1 ~ 255 sec 1290 / AunO / Aunt / A2nO / A2nt / 12nO / 12nt 1 ~ 9999 tyP1 / tyP2 tyP1 / tyP2 tyP1 / tyP2 tyP1 / tyP2 tyP1 / tyP2 bAnd / rEG 0 ~ 100 4800 / 9600 / 192H (19200) / 384H (38400) bps 10 / 100 / 1000 / 3000 msec On / OFF On / OFF On / OFF ­20 ~ 0 ~ +20 kHz (1 kHz/step) OFF / bAnd / FrEq OFF / 3 / 5 / 10 / 15 / 20 / 30 min 30 ~ 49 MHz StP1 / StP2 / OFF nAin (MAIN) / 0~100 1200 / 500 / 300 Hz On / OFF CAr / 5Sec 0 ~ 100 ­25 ~ 0 ~ +25 ­1000 ~ +1000 Hz (20 Hz/step) ­1000 ~ +1000 Hz (20 Hz/step) ­1000 ~ +1000 Hz (20 Hz/step) ­1000 ~ +1000 Hz (20 Hz/step) ­1000 ~ +1000 Hz (20 Hz/step) ­1000 ~ +1000 Hz (20 Hz/step) ­1000 ~ +1000 Hz (20 Hz/step) ­1000 ~ +1000 Hz (20 Hz/step) Ur (VR) / 0 ~ 100 Frnt / dAtA / PC DEFAULT SETTING 300 msec 20 msec 700 msec 20 msec 2000 msec 20 msec bL1 1 7 4 C-tn OFF 0° 0° On 1 ­­ 50 50 OFF 1290 1 tyP2 tyP2 tyP2 tyP2 tyP2 2 bAnd 50 4800 bps 10 msec On On OFF +5 kHz OFF OFF 44 MHz StP1 nAin(MAIN) 1200 Hz On 5SEc 50 0 0 Hz 0 Hz 0 Hz 0 Hz 0 Hz 0 Hz 0 Hz 0 Hz 30 Frnt 1: Requires optional DMU-2000 Data Management Unit. 2: Requires optional FH-2 Remote Control Keypad. FT-2000 OPERATING MANUAL Page 109 MENU MODE GROUP MODE-CW MODE-CW MODE-CW MODE-CW MODE-CW MODE-CW MODE-CW MODE-CW MODE-CW MODE-CW MODE-CW MODE-CW MODE-DAT MODE-DAT MODE-DAT MODE-DAT MODE-DAT MODE-DAT MODE-DAT MODE-DAT MODE-FM MODE-FM MODE-FM MODE-FM MODE-RTY MODE-RTY MODE-RTY MODE-RTY MODE-RTY MODE-RTY MODE-SSB MODE-SSB MODE-SSB MODE-SSB MODE-SSB MODE-SSB RX AUDIO RX AUDIO RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP RX DSP NO. 054 055 056 057 058 059 060 061 062 063 064 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 MENU FUNCTION A1A F-TYPE A1A F-REV A1A R-TYPE A1A R-REV A1A CW AUTO A1A BFO A1A BK-IN A1A SHAPE A1A WEIGHT A1A FRQDISP A1A PC KYNG A1A QSKTIME dAtA DATA IN dAtA DT GAIN dAtA DT OUT dAtA OUT LVL dAtA VOX DLY dAtA V GAIN dAtA PKTDISP dAtA PKT SFT F3E MICGAIN F3E MIC SEL F3E 28 RPT F3E 50 RPT rtty R PLRTY rtty T PLRTY rtty RTY OUT rtty OUT LEL rtty SHIFT rtty TONE J3E MIC SEL J3E TX BPF J3E LSB CAR J3E USB CAR J3E SLSB CR J3E SUSB CR rout AGC SLP rout HEADPHN rdSP CNTR LV rdSP CNTR WI rdSP NOTCH W rdSP CW SHAP rdSP CW SLP rdSP CW NARR rdSP PKT SHP rdSP PKT SLP rdSP PKT NAR rdSP RTY SHP rdSP RTY SLP rdSP RTY NAR rdSP SSB SHP rdSP SSB SLP rdSP SSB NAR AVAILABLE VALUES OFF / buG / ELE / ACS nor / rEU (REV) OFF / buG / ELE / ACS nor / rEU (REV) OFF / 50 / On USb / LSb / Auto SEni (SEMI) / FuLL 1 / 2 / 4 / 6 msec (1:) 2.5 ~ 4.5 dir / OFSt EnA (Enable) / diS (Disable) 15 / 20 / 25 / 30 msec dAtA / PC 0 ~ 100 nAin (Main) / Sub 0 ~ 100 30 ~ 3000 msec 0 ~ 100 ­3000 ~ +3000 Hz (10 Hz/step) ­3000 ~ +3000 Hz (10 Hz/step) Ur (VR) / 0 ~ 100 Frnt / dAtA / PC 0 ~ 1000 kHz (10 kHz/step) 0 ~ 4000 kHz (10 kHz/step) nor / rEU (REV) nor / rEU (REV) nAin (Main) / Sub 0 ~ 100 170 / 200 / 425 / 850 Hz 1275 / 2125 Hz Frnt / dAtA / PC 1-30 / 1-29 / 2-28 / 3-27 / 4-26 / 3000 ­200 Hz ~ +200 Hz (10 Hz/step) ­200 Hz ~ +200 Hz (10 Hz/step) ­200 Hz ~ +200 Hz (10 Hz/step) ­200 Hz ~ +200 Hz (10 Hz/step) nor / SLP SEP / Con1 / Con2 ­40 ~ +20 dB 1 ­ 11 nArr (Narrow) / uuid (Wide) SOFt / ShAP StP(STEEP) / nEd(MEDIUM) / GEnt(GENTLE) 25 / 50 / 100 / 200 / 300 / 400 / 500 / 800 / 1200 / 1400 / 1700 / 2000 Hz SOFt / ShAP StP(STEEP) / nEd(MEDIUM) / GEnt(GENTLE) 25 / 50 / 100 / 200 / 300 / 400 Hz SOFt / ShAP StP(STEEP) / nEd(MEDIUM) / GEnt(GENTLE) 25 / 50 / 100 / 200 / 300 / 400 Hz SOFt / ShAP StP(STEEP) / nEd(MEDIUM) / GEnt(GENTLE) 200 / 400 / 600 / 850 / 1100 / 1350 / 1500 / 1650 / 1800 / 1950 / 2100 / 2250 Hz DEFAULT SETTING ELE nor ELE nor OFF USb SEni (SEMI) 4 msec 3.0 OFSt diS (Disable) 15 msec dAtA 50 nAin (Main) 50 300 msec 50 0 Hz 1000 Hz 50 Frnt 100 kHz 1000 kHz nor nor nAin (Main) 50 170 Hz 2125 Hz Frnt 3-27 0 Hz 0 Hz 0 Hz 0 Hz nor SEP ­15 dB 10 uuid (Wide) ShAP nEd (MEDIUM) 500 Hz ShAP nEd (MEDIUM) 300 Hz ShAP nEd (MEDIUM) 300 Hz ShAP nEd (MEDIUM) 1800 Hz Page 110 FT-2000 OPERATING MANUAL MENU MODE GROUP SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE SCOPE TUNING TUNING TUNING TUNING TUNING TUNING TUNING TX AUDIO TX AUDIO TX AUDIO TX AUDIO TX AUDIO TX AUDIO TX AUDIO TX AUDIO TX AUDIO TX AUDIO TX AUDIO TX AUDIO TX AUDIO TX AUDIO TX AUDIO TX AUDIO TX AUDIO TX AUDIO TX GNRL TX GNRL TX GNRL TX GNRL TX GNRL TX GNRL TX GNRL NO. 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 MENU FUNCTION SCP 1.8 FIX SCP 3.5 FIX SCP 5.0 FIX SCP 7.0 FIX SCP 10.1 FIX SCP 14.0 FIX SCP 18.0 FIX SCP 21.0 FIX SCP 24.8 FIX SCP 28.0 FIX SCP 50.0 FIX tun DIALSTEP tun CW FINE tun MHz SEL tun AM STEP tun FM STEP tun FM DIAL tun MY BAND tAUd EQ1 FRQ tAUd EQ1 LVL tAUd EQ1 BW tAUd EQ2 FRQ tAUd EQ2 LVL tAUd EQ2 BW tAUd EQ3 FRQ tAUd EQ3 LVL tAUd EQ3 BW tAUd PE1 FRQ tAUd PE1 LVL tAUd PE1 BW tAUd PE2 FRQ tAUd PE2 LVL tAUd PE2 BW tAUd PE3 FRQ tAUd PE3 LVL tAUd PE3 BW tGEn BIAS tGEn MAX PWR tGEn PWRCTRL tGEn ETX-GND tGEn TUN PWR tGEn VOX SEL tGEn EMRGNCY AVAILABLE VALUES 1.800 - 1.999 MHz (1 kHz/step) 3.500 - 3.999 MHz (1 kHz/step) 5.250 - 5.499 MHz (1 kHz/step) 7.000 - 7.299 MHz (1 kHz/step) (1)0.100 - (1)0.149 MHz (1 kHz/step) (1)4.000 - (1)4.349 MHz (1 kHz/step) (1)8.000 - (1)8.199 MHz (1 kHz/step) (2)1.000 - (2)1.449 MHz (1 kHz/step) (2)4.800 - (2)4.989 MHz (1 kHz/step) (2)8.000 - (2)9.699 MHz (1 kHz/step) (5)0.000 - (5)3.999 MHz (1 kHz/step) 1 / 5 / 10 Hz EnA / diS 1 / 0.1 MHz 2.5 / 5 / 9 / 10 / 12.5 kHz 5 / 6.25 / 10 / 12.5 / 20 / 25 kHz 10 / 100 Hz 1.8 ~ 50 / GE / AU OFF / 100 ~ 700 Hz (100 Hz/step) ­20 ~ +10 1 ~ 10 OFF / 700 ~ 1500 Hz (100 Hz/step) ­20 ~ +10 1 ~ 10 OFF / 1500 ~ 3200 Hz (100 Hz/step) ­20 ~ +10 1 ~ 10 OFF / 100 ~ 700 Hz (100 Hz/step) ­20 ~ +10 1 ~ 10 OFF / 700 ~ 1500 Hz (100 Hz/step) ­20 ~ +10 1 ~ 10 OFF / 1500 ~ 3200 Hz (100 Hz/step) ­20 ~ +10 1 ~ 10 ­­ 10 / 20 / 50 / 100 W ALL / Car EnA (ENABLE) / diS (DISABLE) 10 / 20 / 50 / 100 W nic (MIC) / dAtA EnA (ENABLE) / diS (DISABLE) DEFAULT SETTING 1.800 MHz 1 3.500 MHz 1 5.250 MHz 1 7.000 MHz 1 (1)0.100 MHz 1 (1)4.000 MHz 1 (1)8.068 MHz 1 (2)1.000 MHz 1 (2)4.890 MHz 1 (2)8.000 MHz 1 (5)0.000 MHz 1 10 Hz diS 1 MHz 5 kHz 5 kHz 100 Hz ­­ OFF +5 10 OFF +5 10 OFF +5 10 200 Hz 0 2 800 Hz 0 1 2100 Hz 0 1 ­­ 2 100 W ALL diS (DISABLE) 100 W nic (MIC) diS (DISABLE) 1: Requires optional DMU-2000 Data Management Unit. 2: This Menu item does not work. Please do not change this setting. FT-2000 OPERATING MANUAL Page 111 MENU MODE AGC GROUP 001 AGc FST DLY Function: Sets the delay time for the AGC FAST mode of the Main band (VFO-A) receiver. Available Values: 20 ~ 4000 msec (20 msec/step) Default Setting: 300 msec DISPLAY GROUP 007 diSP COLOR Function: Selects the Display color when the optional Data Management Unit (DMU-2000) is connected. Available Values: bL1 / bL2 / bL3 / ub1 / ub2 bL1: COOL BLUE bL2: CONTRAST BLUE bL3: FLASH WHITE ub1: CONTRAST UMBER ub2: UMBER Default Setting: bL1 (COOL BLUE) ADVICE: If the optional DMU-2000 Data Management Unit is not connected, this adjustment has no effect. 002 AGc FST HLD Function: Sets the hang time of the AGC peak voltage for the AGC FAST mode of the Main band (VFO-A) receiver. Available Values: 0 ~ 2000 msec (20 msec/step) Default Setting: 20 msec 003 AGc MID DLY Function: Sets the delay time for the AGC MID mode of the Main band (VFO-A) receiver. Available Values: 20 ~ 4000 msec (20 msec/step) Default Setting: 700 msec 008 diSP DIM MTR Function: Setting of the meter brightness level when "DIM" is selected. Available Values: 0 ~ 15 Default Setting: 7 004 AGc MID HLD Function: Sets the hang time of the AGC peak voltage for the AGC MID mode of the Main band (VFO-A) receiver. Available Values: 0 ~ 2000 msec (20 msec/step) Default Setting: 20 msec 009 diSP DIM VFD Function: Setting of the frequency display brightness level when "DIM" is selected. Available Values: 0 ~ 7 Default Setting: 4 005 AGc SLW DLY Function: Sets the delay time for the AGC SLOW mode of the Main band (VFO-A) receiver. Available Values: 20 ~ 4000 msec (20 msec/step) Default Setting: 2000 msec 010 diSP BAR SEL Function: Selects one of three parameters to be viewed on the Tuning Offset Indicator. Available Values: CLAr / C-tn / u-tn Default Setting: C-tn CLAr: Displays relative clarifier offset. C-tu: Displays relative CW tuning offset between the incoming signal and transmitted frequency. u-tn: Displays the peak position of the VRF or TUNE filter. NOTE: The -TUNE filter is an option. 006 AGc SLW HLD Function: Sets the hang time of the AGC peak voltage for the AGC SLOW mode of the Main band (VFO-A) receiver. Available Values: 0 ~ 2000 msec (20 msec/step) Default Setting: 20 msec 011 diSP PK HLD Function: Selects the peak hold time of the Sub (VFO-B) receiver's S-meter. Available Values: OFF / 0.5 / 1.0 / 2.0 sec Default Setting: OFF 012 diSP RTR STU Function: Selects the starting point of your rotator controller's indicator needle. Available Values: 0 / 90 / 180 / 270° Default Setting: 0° 013 diSP RTR ADJ Function: Adjusts the indicator needle precisely to the starting point set in menu item "012 diSP RTR STU." Available Values: ­30 ~ 0° Default Setting: 0° Page 112 FT-2000 OPERATING MANUAL MENU MODE DISPLAY GROUP 014 diSP QMB MKR Function: Enables/Disables the QMB Marker (White arrow " ") to display on the Spectrum Band Scope when the optional DMU-2000 Data Management Unit is connected. Available Values: On / OFF Default Setting: On ADVICE: If the optional DMU-2000 Data Management Unit is not connected, this adjustment has no effect. KEYER GROUP 018 tEy BEACON Function: Sets the interval time between repeats of the beacon message. Available Values: OFF / 1 ~ 255 sec Default Setting: OFF 019 tEy NUM STL Function: Selects the Contest Number "Cut" format for an imbedded contest number. Available Values: 1290 / AunO / Aunt / A2nO / A2nt / 12nO / 12nt Default Setting: 1290 1290: Does not abbreviate the Contest Number AunO: Abbreviates to "A" for "One," "U" for "Two," "N" for "Nine," and "O" for "Zero." Aunt: Abbreviates to "A" for "One," "U" for "Two," "N" for "Nine," and "T" for "Zero." A2nO: Abbreviates to "A" for "One," "N" for "Nine," and "O" for "Zero." A2nt: Abbreviates to "A" for "One," "N" for "Nine," and "T" for "Zero." 12nO: Abbreviates to "N" for "Nine," and "O" for "Zero." 12nt: Abbreviates to "N" for "Nine," and "T" for "Zero." 015 diSP LVL IND Function: Enables/Disables the Sub band (VFO-B) frequency display to show each frequency or value while each of the enabled knob is turned. Available Values: PI (PITCH) / SP (SPEED) / CO (CONTOUR) / nO (NOTCH) / dn (DNR) / Cd (CW DELAY) / Ud (VOX DEALAY) / rP (RF POWER) / nG (MIC GAIN) / Pr (PROCESSOR GAIN) / SH (IF SHIFT) / UI (IF WIDTH) To disable the "function," rotate the [SUB VFO-B] knob to recall the "function" to be disabled, then press the [ENT] key to change this setting to "OFF" (a "E" notation will E replace the "d" notation). Repeat the same procedures to d enable a function (setting it to "ON" ("E" notation apE pears)"). 020 tEy CONTEST Function: Enters the initial contest number that will increment/decrement after sending during contest QSOs. Available Values: 1 ~ 9999 Default Setting: 1 ADVICE: Press the [CLEAR] button to reset the contest number to "1." DVS GROUP 016 dUS RX LVL Function: Sets the audio output level from the voice memory. Available Values: 0 ~ 100 Default: 50 017 dUS TX LVL Function: Sets the microphone input level to the voice memory Available Values: 0 ~ 100 Default: 50 021 tEy CW MEM1 Function: Permits entry of the CW message for message register 1. Available Values: tyP1 / tyP2 Default Setting: tyP2 tyP1: You may enter the CW message from the front panel's Function Keys. tyP2: You may enter the CW message from the CW keyer. 022 tEy CW MEM2 Function: Permits entry of the CW message for message register 2. Available Values: tyP1 / tyP2 Default Setting: tyP2 tyP1: You may enter the CW message from the front panel's Function Keys. tyP2: You may enter the CW message from the CW keyer. FT-2000 OPERATING MANUAL Page 113 MENU MODE KEYER GROUP 023 tEy CW MEM3 Function: Permits entry of the CW message for message register 3. Available Values: tyP1 / tyP2 Default Setting: tyP2 tyP1: You may enter the CW message from the front panel's Function Keys. tyP2: You may enter the CW message from the CW keyer. GENERAL GROUP 026 GEnE ANT SEL Function: Sets the method of antenna selection. Available Values: bAnd / rEG Default Setting: bAnd bAnd:The antenna is selected in accordance with the operating band. rEG: The antenna is selected in accordance with the band stack (different antennas may be utilized on the same band, if so selected in the band stack). 024 tEy CW MEM4 Function: Permits entry of the CW message for message register 4. Available Values: tyP1 / tyP2 Default Setting: tyP2 tyP1: You may enter the CW message from the front panel's Function Keys. tyP2: You may enter the CW message from the CW keyer. 027 GEnE BEP LVL Function: Sets the beep level. Available Values: 0 ~ 100 Default Setting: 50 028 GEnE CAT BPS Function: Sets the transceiver's computer-interface circuitry for the CAT baud rate to be used. Available Values: 4800 / 9600 / 192H(19200) / 384H (38400) bps Default Setting: 4800 bps 025 tEy CW MEM5 Function: Permits entry of the CW message for message register 5. Available Values: tyP1 / tyP2 Default Setting: tyP2 tyP1: You may enter the CW message from the front panel's Function Keys. tyP2: You may enter the CW message from the CW keyer. ADVICE: If the optional FH-2 Remote Control Keypad is not connected, this adjustment has no effect. 029 GEnE CAT TOT Function: Sets the Time-Out Timer countdown time for a CAT command input. Available Values: 10 / 100 / 1000 / 3000 msec Default Setting: 10 msec The Time-Out Timer shuts off the CAT data input after the continuous transmission of the programmed time. 030 GEnE CAT RTS Function: Enables/Disables the RTS port of the CAT jack. Available Values: On/OFF Default Setting: On 031 GEnE CAT IND Function: Enables/Disables the flashing of the Data LED inside the [CS] switch in conjunction with the CAT commands. Available Values: On / OFF Default Setting: On 032 GEnE MEM GRP Function: Enables/Disables Memory Group Operation. Available Values: On / OFF Default Setting: OFF 033 GEnE Q SPLIT Function: Selects the tuning offset for the Quick Split feature. Available Values: ­20 ~ 0 ~ +20 kHz (1 kHz Step) Default Setting: +5 kHz Page 114 FT-2000 OPERATING MANUAL MENU MODE GENERAL GROUP 034 GEnE TRACK Function: Sets the VFO Tracking feature. Available Values: OFF / bAND / FrEq Default Setting: OFF OFF: Disables the VFO Tracking feature. bAND: When you change bands on the Main (VFOA) side, the Sub (VFO-B) band's VFO will automatically change to be the same as that of VFO-A. FrEq: This function is the almost same as "bAND," however, furthermore, the Sub band's (VFOB) frequency changes together with the Main Band's (VFO-A) frequency when turning the Main Dial Tuning knob. 038 GEnE SNB LVL Function: Adjusts the Sub band (VFO-B) receiver's IF Noise Blanker level, when the Noise Blanker is engaged. Available Values: nAin(MAIN) / 0~100 Default Setting: nAin(MAIN) When this menu is set to "nAin(MAIN)," you may adjust the Noise Blanker level using the front panel's [NB] knob. 039 GEnE SUB FIL Function: Defines the Sub band (VFO-B) receiver's CW narrow filter. Available Values: 1200 / 500 / 300 Hz Default Setting: 1200 Hz ADVICE: This Menu item tells the microprocessor which (if any) optional filter has been installed. 035 GEnE TX TOT Function: Sets the Time-Out Timer countdown time. Available Values: OFF / 3 / 5 / 10 / 15 / 20 / 30 min Default Setting: OFF The Time-Out Timer shuts off the transmitter after continuous transmission of the programmed time. 040 GEnE MIC SCN Function: Enables/disables scanning access via the microphone's [UP]/[DWN] keys. Available Values: On / OFF Default Setting: On 036 GEnE TRV SET Function: Sets the 10's and 1's of the MHz digits display for operation with a transverter. Available Values: 30 ~ 49 MHz Default Setting: 44 MHz The default setting would be used with a 144 MHz transverter. If you connect a 430 MHz transverter to the radio, set this menu to "30" (the "100 MHz" digits are hidden on this radio). 041 GEnE SCN RSM Function: Selects the Scan Resume mode. Available Values: CAr / 5SEc Default Setting: 5SEc CAr: The scanner will hold until the signal disappears, then will resume after one second. 5SEc: The scanner will hold for five seconds, then resume whether or not the other station is still transmitting. 037 GEnE T DIAL Function: Selects the -TUNE mode. Available Values: StP1 / StP2 / OFF Default Setting: StP1 StP1: A c t i v a t e s t h e - T U N E s y s t e m u s i n g "COARSE" steps of the [VRF] knob (2 steps/ click) on the 7 MHz and lower amateur bands. On the 10/14 MHz bands, "FINE" [VRF] knob steps (1 step/click) will be used. StP2: Activates the -TUNE system using "FINE" steps of the [VRF] knob (1 step/click) on the 14 MHz and lower amateur bands on the Main band (VFO-A). OFF: Disables the -TUNE system. Activates the VRF feature on the 14 MHz and lower amateur bands on the main band (VFO-A). ADVICE: If the optional RF Tuning Kit is not connected, this adjustment has no effect. 042 GEnE ANTIVOX Function: Adjusts the Anti-VOX Trip Gain which is the level of negative feedback of receiver audio to the microphone, to prevent receiver audio from activating the transmitter (via the microphone) during VOX operation. Available Values: 0 ~ 100 Default Setting: 50 043 GEnE FRQ ADJ Function: Adjusts the reference oscillator. Available Values: ­25 ~ 0 ~ +25 Default Setting: 0 Connect a 50-Ohm dummy load and frequency counter to the antenna jack; adjust the [SUB VFO-B] knob so that the frequency counter reading is same as the VFO frequency while pressing the PTT switch. ADVICE: Do not perform this Menu item unless you have a highperformance frequency counter. Perform this Menu item after aging the transceiver and frequency counter sufficiently (at least 30 minutes). FT-2000 OPERATING MANUAL Page 115 MENU MODE S IF SFT (SUB BAND IF SHIFT) GROUP 044 S-iF LSB SFT Function: Sets the center frequency of the Sub band (VFOB) receiver's IF filter in the LSB mode. Available Values: ­1000 ~ +1000 Hz (20Hz/step) Default Setting: 0 Hz MODE-AM GROUP 052 A3E MICGAIN Function: Sets the microphone gain for the AM mode. Available Values: Ur (VR) / 0 ~ 100 Default Setting: 30 When this menu is set to "Ur (VR)," you may adjust the microphone gain using the front panel's [MIC] knob. 045 S-iF USB SFT Function: Sets the center frequency of the Sub band (VFOB) receiver's IF filter in the USB mode. Available Values: ­1000 ~ +1000 Hz (20Hz/step) Default Setting: 0 Hz 053 A3E MIC SEL Function: Selects the microphone to be used on the AM mode. Available Values: Frnt / dAtA / PC Default Setting: Frnt Frnt: Selects the microphone connected to the front panel's MIC jack while using the AM mode. dAtA: Selects the microphone connected to pin 1 of the PACKET Jack while using the AM mode. PC: This parameter is for future expansion of this transceiver's capabilities, but at this time is not supported. 046 S-iF CWL SFT Function: Sets the center frequency of the Sub band (VFOB) receiver's IF filter in the CW (LSB) mode. Available Values: ­1000 ~ +1000 Hz (20Hz/step) Default Setting: 0 Hz 047 S-iF CWU SFT Function: Sets the center frequency of the Sub band (VFOB) receiver's IF filter in the CW (USB) mode. Available Values: ­1000 ~ +1000 Hz (20Hz/step) Default Setting: 0 Hz 048 S-iF RTTY Function: Sets the center frequency of the Sub band (VFOB) receiver's IF filter in the RTTY mode. Available Values: ­1000 ~ +1000 Hz (20Hz/step) Default Setting: 0 Hz 049 S-iF RTTY-R Function: Sets the center frequency of the Sub band (VFOB) receiver's IF filter in the RTTY reverse mode. Available Values: ­1000 ~ +1000 Hz (20Hz/step) Default Setting: 0 Hz 050 S-iF PKT-LSB Function: Sets the center frequency of the Sub band (VFOB) receiver's IF filter in the Packet (LSB) mode. Available Values: ­1000 ~ +1000 Hz (20Hz/step) Default Setting: 0 Hz 051 S-iF PKT-USB Function: Sets the center frequency of the Sub band (VFOB) receiver's IF filter in the Packet (USB) mode. Available Values: ­1000 ~ +1000 Hz (20Hz/step) Default Setting: 0 Hz Page 116 FT-2000 OPERATING MANUAL MENU MODE MODE-CW GROUP 054 A1A F-TYPE Function: Selects the desired keyer operation mode for the device connected to the front panel's KEY jack. Available Values: OFF / buG / ELE / ACS Default Setting: ELE OFF: Disables the front panel's keyer ("straight key" mode for use with external keyer or computerdriven keying interface). buG: Mechanical "bug" keyer emulation. One paddle produces "dits" automatically, while the other paddle manually produces "dahs." ELE: Iambic keyer with ACS (Automatic Character Spacing) disabled. ACS: Iambic keyer with ACS (Automatic Character Spacing) enabled. 058 A1A CW AUTO Function: Enables/disables CW keying while operating on SSB. Available Values: OFF / 50 / On Default Setting: OFF OFF: Disables CW keying while operating on SSB. 50: Enables CW keying only while operating SSB on 50 MHz (but not HF). On: Enables CW keying while operating on SSB (all TX bands). NOTE: This feature allows you to move someone from SSB to CW without having to change modes on the front panel. 059 A1A BFO Function: Sets the CW carrier oscillator injection side for the CW mode. Available Values: USb / LSb / Auto Default Setting: USb USb: Injects the CW carrier oscillator on the USB side. LSb: Injects the CW carrier oscillator on the LSB side. Auto: Injects the CW carrier oscillator on the LSB side while operating on the 7 MHz band and below, and the USB side while operating on the 10 MHz band and up. 055 A1A F-REV Function: Selects the keyer paddle's wiring configuration for the KEY jack on the front panel. Available Values: nor / rEU (REV) Default Setting: nor nor: Tip = Dot, Ring = Dash, Shaft = Ground rEU (REV): Tip = Dash, Ring = Dot, Shaft = Ground 056 A1A R-TYPE Function: Selects the desired keyer operation mode for the device connected to the rear panel's KEY jack. Available Values: OFF / buG / ELE / ACS Default Setting: ELE OFF: Disables the rear panel's keyer ("straight key" mode for use with external keyer or computerdriven keying interface). buG: Mechanical "bug" keyer emulation. One paddle produces "dits" automatically, while the other paddle manually produces "dahs." ELE: Iambic keyer with ACS (Automatic Character Spacing) disabled. ACS: Iambic keyer with ACS (Automatic Character Spacing) enabled. 060 A1A BK-IN Function: Sets the CW "break-in" mode. Available Values: SEni / FuLL Default Setting: SEni SEni (SEMI): The transceiver will operate in the semi break-in mode. The delay (receiver recovery) time is set by the front panel's [DELAY] knob. FuLL: The transceiver will operate in the full break-in (QSK) mode. 061 A1A SHAPE Function: Selects the CW carrier wave-form shape (rise/ fall times). Available Values: 1 / 2 / 4 / 6 msec Default Setting: 4 msec 057 A1A R-REV Function: Selects the keyer paddle's wiring configuration for the KEY jack on the rear panel. Available Values: nor / rEU (REV) Default Setting: nor nor: Tip = Dot, Ring = Dash, Shaft = Ground rEU (REV): Tip = Dash, Ring = Dot, Shaft = Ground 062 A1A WEIGHT Function: Sets the Dot:Dash ratio for the built-in electronic keyer. Available Values: (1:) 2.5 ~ 4.5 Default Setting: 3.0 FT-2000 OPERATING MANUAL Page 117 MENU MODE MODE-CW GROUP 063 A1A FRQDISP Function: Selects the frequency Display Format for the CW mode. Available Values: dir / OFSt Default Setting: OFSt dir (Direct Frequency): Displays the receiver carrier frequency, without any offset added. When changing modes between SSB and CW, the frequency display remains constant. OFSt (Pitch Offset): This frequency display reflects the added BFO offset. MODE-DAT GROUP 066 dAtA DATA IN Function: Selects the data input path to be used on the PKT mode. Available Values: dAtA / PC Default Setting: dAtA dAtA:Uses the data input line connected to pin 1 of the PACKET jack while using the PKT mode. PC: This parameter is for future expansion of this transceiver's capabilities, but at this time is not supported. 067 dAtA DT GAIN Function: Sets the data input level from the TNC to the AFSK modulator. Available Values: 0 ~ 100 Default Setting: 50 064 A1A PC KYNG Function: Enables/disables CW keying from the "PACKET PTT" terminal (pin 3) on the rear panel's PACKET jack while operating on the CW mode. Available Values: EnA (Enable) / diS (Disable) Default Setting: diS (Disable) 068 dAtA DT OUT Function: Selects the receiver to be connected to the data output port (pin 4) of the PACKET jack. Available Values: nAin (Main) / Sub Default Setting: nAin (Main) 065 A1A QSKTIME Function: Selects the time delay between when the PTT is keyed and the carrier is transmitted during QSK operation when using the internal keyer. Available Values: 15 / 20 / 25 / 30 msec Default Setting: 15 msec 069 dAtA OUT LVL Function: Sets the AFSK data output level at the output port (pin 4) of the PACKET jack. Available Values: 0 ~ 100 Default Setting: 50 070 dAtA VOX DLY Function: Adjusts the "VOX" delay (receiver recovery) time on the PKT mode. Available Values: 30 ~ 3000 msec Default Setting: 300 msec 071 dAtA V GAIN Function: Adjusts the "VOX" gain on the PKT mode. Available Values: 0 ~ 100 Default Setting: 50 072 dAtA PKTDISP Function: Sets the packet frequency display offset. Available: ­3000 ~ +3000 Hz (10 Hz/step) Default: 0 Hz 073 dAtA PKT SFT Function: Sets the carrier point during the SSB packet operation. Available: ­3000 ~ +3000 Hz (10 Hz/step) Default: 1000 Hz (typical center frequency for PSK31, etc.) Page 118 FT-2000 OPERATING MANUAL MENU MODE MODE-FM GROUP 074 F3E MICGAIN Function: Sets the microphone gain for the FM mode. Available Values: Ur (VR) / 0 ~ 100 Default Setting: 50 When this menu is set to "Ur (VR)," you may adjust the microphone gain using the front panel's [MIC] knob. MODE-RTY GROUP 078 rtty R PLRTY Function: Selects normal or reverse Mark/Space polarity for RTTY receive operation. Available Values: nor / rEU (REV) Default Setting: nor 075 F3E MIC SEL Function: Selects the microphone to be used on the FM mode. Available Values: Frnt / dAtA / PC Default Setting: Frnt Frnt (FRONT): Selects the microphone connected to the front panel's MIC jack while using the FM mode. dAtA: Selects the microphone connected to pin 1 of the PACKET Jack while using the FM mode. PC: This parameter is for future expansion of this transceiver's capabilities, but at this time is not supported. 079 rtty T PLRTY Function: Selects normal or reverse Mark/Space polarity for RTTY transmit operation. Available Values: nor / rEU (REV) Default Setting: nor 080 rtty RTY OUT Function: Selects the receiver to be connected to the data output port (pin 2) of the RTTY jack. Available Values: nAin (Main) / Sub Default Setting: nAin (Main) 081 rtty OUT LEL Function: Sets the FSK RTTY data output level at the output port (pin 2) of the RTTY jack. Available Values: 0 ~ 100 Default Setting: 50 076 F3E 28 RPT Function: Sets the magnitude of the repeater shift on the 28 MHz band. Available Values: 0 ~ 1000 kHz (10 kHz/step) Default Setting: 100 kHz 082 rtty SHIFT Function: Selects the frequency shift for FSK RTTY operation. Available Values:170 / 200 / 425 / 850 Hz Default Setting: 170 Hz 077 F3E 50 RPT Function: Sets the magnitude of the repeater shift on the 50 MHz band. Available Values: 0 ~ 4000 kHz (10 kHz/step) Default Setting: 1000 kHz 083 rtty TONE Function: Selects the Mark tone for RTTY operation. Available Values: 1275 / 2125 Hz Default Setting: 2125 Hz FT-2000 OPERATING MANUAL Page 119 MENU MODE MODE-SSB GROUP 084 J3E MIC SEL Function: Selects the microphone to be used on the SSB modes (LSB and USB). Available Values: Frnt / dAtA / PC Default Setting: Frnt Frnt (FRONT): Selects the microphone connected to the front panel's MIC jack while using the SSB modes. dAtA: Selects the microphone connected to pin 1 of the PACKET Jack while using the SSB modes. PC: This parameter is for future expansion of this transceiver's capabilities, but at this time is not supported. RX AUDIO GROUP 090 rout AGC SLP Function: Selects the gain curve of the AGC amplifier. Available Values: nor / SLP Default Setting: nor nor (NORMAL): The AGC output level will follow a linear response to the antenna input level, while AGC is activated. SLP (SLOPED): The AGC output level will increase at 1/10 the rate of the antenna input level, while AGC is activated. SLOPE Audio Output NORMAL 085 J3E TX BPF Function: Selects the audio passband of the DSP modulator on the SSB mode. Available Values: 1-30 / 1-29 / 2-28 / 3-27 / 4-26 / 3000 1-30: 50-3000(Hz) 1-29: 100-2900(Hz) 2-28: 200-2800(Hz) 3-27: 300-2700(Hz) 4-26: 400-2600(Hz) 3000: 3000WB Default Setting: 3-27 (300-2700 Hz) NOTE: The apparent power output, when using the widest bandwidths, may seem lower. This is normal, and it occurs because the available transmitter power is distributed over a wider bandwidth. The greatest compression of power output, conversely, occurs when using the "4-26" setting (4002600 Hz), and this setting is highly recommended for contest or DX pile-up work. Input Signal 091 rout HEADPHN Function: Selects one of three audio mixing modes when using headphones during Dual Receive operation. Available Values: SEP / Con1 / Con2 Default Setting: SEP SEP (SEPARATE): Audio from the Main (VFO-A) receiver is heard only in the left ear, and Sub (VFO-B) receiver audio solely in the right ear. Con1 (COMBINE 1): Audio from both Main (VFOA) and Sub (VFO-B) receivers can be heard in both ears, but Sub (VFO-B) audio is attenuated in the left ear and Main (VFO-A) audio is attenuated in the right ear. Con2 (COMBINE 2): Audio from both Main (VFOA) and Sub (VFO-B) receivers is combined and heard equally in both ears. 086 J3E LSB CAR Function: Adjusts the receiver carrier point for the Main band's (VFO-A) LSB mode. Available Values: ­200 Hz ~ +200 Hz (10 Hz/steps) Default Setting: 0 Hz 087 J3E USB CAR Function: Adjusts the receiver carrier point for Main band's (VFO-A) USB mode. Available Values: ­200 Hz ~ +200 Hz (10 Hz/step) Default Setting: 0 Hz 088 J3E SLSB CR Function: Adjusts the receiver carrier point for the Sub band's (VFO-B) LSB mode. Available Values: ­200 Hz ~ +200 Hz (10 Hz/step) Default Setting: 0 Hz 089 J3E SUSB CR Function: Adjusts the receiver carrier point for Sub band's (VFO-B) USB mode. Available Values: ­200 Hz ~ +200 Hz (10 Hz/step) Default Setting: 0 Hz Page 120 FT-2000 OPERATING MANUAL MENU MODE RX DSP GROUP 092 rdSP CNTR LV Function: Adjusts the gain of the Contour filter. Available Values: ­40 ~ +20 dB Default Setting: ­15 dB 098 rdSP PKT SHP Function: Selects the passband characteristics of the DSP filter for the PKT mode. Available Values: SOFt / ShAP Default Setting: ShAP SOFt (SOFT): Primary importance is attached to the phase of the filter factor. ShAP (SHARP): Primary importance is attached to the amplitude of the filter factor. 093 rdSP CNTR WI Function: Adjusts the Q-factor of the Contour filter. Available Values: 1 - 11 Default Setting: 10 "Q" "+" Gain "-- " Gain 099 rdSP PKT SLP Function: Selects the shape factor of the DSP filter for the PKT mode. Available Values: StP(STEEP) / nEd(MEDIUM) / GEnt(GENTLE) Default Setting: nEd (MEDIUM) 100 rdSP PKT NAR IF BANDWIDTH CONTOUR "GAIN" AND "Q" Function: Selects the passband of the DSP filter for the PKT "Narrow" mode. Available Values: 25 / 50 / 100 / 200 / 300 / 400 Hz Default Setting: 300 Hz 094 rdSP NOTCH W Function: Selects the bandwidth of the DSP NOTCH filter Available Values: nArr (Narrow) / uuid (Wide) Default Setting: uuid (Wide) 101 rdSP RTY SHP Function: Selects the passband characteristics of the DSP filter for the RTTY mode. Available Values: SOFt / ShAP Default Setting: ShAP SOFt (SOFT): Primary importance is attached to the phase of the filter factor. ShAP (SHARP): Primary importance is attached to the amplitude of the filter factor. 095 rdSP CW SHAP Function: Selects the passband characteristics of the DSP filter for the CW mode. Available Values: SOFt / ShAP Default Setting: ShAP SOFt (SOFT): Primary importance is attached to the phase of the filter factor. ShAP (SHARP): Primary importance is attached to the amplitude of the filter factor. 102 rdSP RTY SLP Function: Selects the shape factor of the DSP filter for the RTTY mode. Available Values: StP(STEEP) / nEd(MEDIUM) / GEnt(GENTLE) Default Setting: nEd (MEDIUM) 096 rdSP CW SLP Function: Selects the shape factor of the DSP filter for the CW mode. Available Values: StP(STEEP) / nEd(MEDIUM) / GEnt(GENTLE) Default Setting: nEd (MEDIUM) 103 rdSP RTY NAR Function: Selects the passband of the DSP filter for the RTTY "Narrow" mode. Available Values: 25 / 50 / 100 / 200 / 300 / 400 Hz Default Setting: 300 Hz 097 rdSP CW NARR Function: Selects the passband of the DSP filter for the CW "Narrow" mode. Available Values: 25 / 50 / 100 / 200 / 300 / 400 / 500 / 800 / 1200 / 1400 / 1700 / 2000 Hz Default Setting: 500 Hz FT-2000 OPERATING MANUAL Page 121 MENU MODE RX DSP GROUP 104 rdSP SSB SHP Function: Selects the passband characteristics of the DSP filter for the SSB modes (LSB and USB). Available Values: SOFt / ShAP Default Setting: ShAP SOFt (SOFT): Primary importance is attached to the phase of the filter factor. ShAP (SHARP): Primary importance is attached to the amplitude of the filter factor. SCOPE GROUP ADVICE: This group's adjustment has no effect, if the optional DMU2000 Data Management Unit is not connected. 107 SCP 1.8 FIX Function: Selects the scan start frequency of the FIX mode Spectrum Scope while monitoring on the 160 m amateur band. Available Values: 1.800 - 1.999 MHz (1 kHz/step) Default Setting: 1.800 MHz 105 rdSP SSB SLP Function: Selects the shape factor of the DSP filter for the SSB modes (LSB and USB). Available Values: StP(STEEP) / nEd(MEDIUM) / GEnt(GENTLE) Default Setting: nEd (MEDIUM) 108 SCP 3.5 FIX Function: Selects the scan start frequency of the FIX mode Spectrum Scope while monitoring on the 80 m amateur band. Available Values: 3.500 - 3.999 MHz (1 kHz/step) Default Setting: 3.500 MHz 106 rdSP SSB NAR Function: Selects the passband of the DSP filter for the "Narrow" SSB mode. Available Values: 200 / 400 / 600 / 850 / 1100 / 1350 / 1500 / 1650 / 1800 / 1950 / 2100 / 2250 Hz Default Setting: 1800 Hz 109 SCP 5.0 FIX Function: Selects the scan start frequency of the FIX mode Spectrum Scope while monitoring on the 60 m amateur band. Available Values: 5.250 - 5.499 MHz (1 kHz/step) Default Setting: 5.250 MHz 110 SCP 7.0 FIX Function: Selects the scan start frequency of the FIX mode Spectrum Scope while monitoring on the 40 m amateur band. Available Values: 7.000 - 7.299 MHz (1 kHz/step) Default Setting: 7.000 MHz STEEP MEDIUM GENTLE 111 SCP 10.1 FIX Function: Selects the scan start frequency of the FIX mode Spectrum Scope while monitoring on the 30 m amateur band. Available Values: (1)0.100 - (1)0.149 MHz (1 kHz steps) Default Setting: (1)0.100 MHz DSP FILTER PASSBAND SHARP SOFT DSP FILTER SHAPE Page 122 FT-2000 OPERATING MANUAL MENU MODE SCOPE GROUP 112 SCP 14.0 FIX Function: Selects the scan start frequency of the FIX mode Spectrum Scope while monitoring on the 20 m amateur band. Available Values: (1)4.000 - (1)4.349 MHz (1 kHz/step) Default Setting: (1)4.000 MHz TUNING GROUP 118 tun DIALSTEP Function: Setting of the Tuning Dial knob's tuning speed except the FM and FM-PKT modes. Available Values: 1 / 5 / 10 Hz Default Setting: 10 Hz 113 SCP 18.0 FIX Function: Selects the scan start frequency of the FIX mode Spectrum Scope while monitoring on the 17 m amateur band. Available Values: (1)8.000 - (1)8.199 MHz (1 kHz/step) Default Setting: (1)8.068 MHz 119 tun CW FINE Function: Enabling/disabling of the "Fine" tuning speed in the CW, RTTY, and PKT-SSB modes. Available Values: EnA (ENABLE) / diS (DISABLE) Default Setting: diS (DISABLE) EnA (ENABLE): Tuning in 1 Hz steps on the CW, RTTY, and PKT-SSB modes. diS (DISABLE): Tuning according to the steps determined via menu item "118 tun DIALSTEP." 114 SCP 21.0 FIX Function: Selects the scan start frequency of the FIX mode Spectrum Scope while monitoring on the 15 m amateur band. Available Values: (2)1.000 - (2)1.449 MHz (1 kHz/step) Default Setting: (2)1.000 MHz 120 tun MHz SEL Function: Selects the tuning steps for the [SUB VFO-B] knob when the [MHz] button is pressed. Available Values: 1 / 0.1 MHz Default Setting: 1 MHz 115 SCP 24.8 FIX Function: Selects the scan start frequency of the FIX mode Spectrum Scope while monitoring on the 12 m amateur band. Available Values: (2)4.800 - (2)4.989 MHz (1 kHz/step) Default Setting: (2)4.890 MHz 121 tun AM STEP Function: Selects the tuning steps for the microphone's [UP]/[DWN] keys in the AM mode. Available Values: 2.5 / 5 / 9 / 10 / 12.5 kHz Default Setting: 5 kHz 116 SCP 28.0 FIX Function: Selects the scan start frequency of the FIX mode Spectrum Scope while monitoring on the 10 m amateur band. Available Values: (2)8.000 - (2)9.699 MHz (1 kHz/step) Default Setting: (2)8.000 MHz 122 tun FM STEP Function: Selects the tuning steps for the microphone's [UP]/[DWN] keys in the FM and FM-PKT modes. Available Values: 5 / 6.25 / 10 / 12.5 / 20 / 25 kHz Default Setting: 5 kHz 117 SCP 50.0 FIX Function: Selects the scan start frequency of the FIX mode Spectrum Scope while monitoring on the 6 m amateur band. Available Values: (5)0.000 - (5)3.999 MHz (1 kHz/step) Default Setting: (5)0.000 MHz 123 tun FM DIAL Function: Setting of the Tuning Dial knob's tuning speed in the FM mode. Available Values: 10 / 100 Hz Default Setting: 100 Hz 124 tun MY BAND Function: Programs a band to be skipped while selecting bands using the [SUB VFO-B] knob. Available Values: 1.8 ~ 50 / GE / AU Default Setting: --To program the band to be skipped, rotate the [SUB VFOB] knob to recall the band to be skipped while selecting bands via the [SUB VFO-B] knob, then press the [ENT] button to change this setting to "ON" (a "d" notation will d replace the "E" notation). Repeat the same procedures to E cancel the setting (skipped "Off": "d" notation appears). d FT-2000 OPERATING MANUAL Page 123 MENU MODE TX AUDIO GROUP 125 tAUd EQ1 FRQ Function: Selects the center frequency of the lower range for the parametric microphone equalizer. Available Values: OFF / 100 ~ 700 Hz (100 Hz/step) Default Setting: OFF OFF: The equalizer gain and Q-factor are set to factory defaults (flat). 100 ~ 700: Center frequencies of 100 Hz ~ 700 Hz. You may adjust the equalizer gain and Qfactor at this selected audio frequency via menu items "126 tAUd EQ1 LVL" and "127 tAUd EQ1 BW." 131 tAUd EQ3 FRQ Function: Selects the center frequency of the high range for the parametric microphone equalizer. Available Values: OFF / 1500 ~ 3200 Hz (100 Hz/step) Default Setting: OFF OFF: The equalizer gain and Q-factor are set to factory defaults (flat). 1500 ~ 3200: Center frequencies of 1500 Hz ~ 3200 Hz. You may adjust the equalizer gain and Q-factor in this selected audio frequency via menu items "132 tAUd EQ3 LVL" and "133 tAUd EQ3 BW." 126 tAUd EQ1 LVL Function: Adjusts the equalizer gain of the low range of the parametric microphone equalizer. Available Values: ­20 ~ +10 Default Setting: +5 132 tAUd EQ3 LVL Function: Adjusts the equalizer gain of the high range of the parametric microphone equalizer. Available Values: ­20 ~ +10 Default Setting: +5 127 tAUd EQ1 BW Function: Adjusts the Q-factor of the low range of the parametric microphone equalizer. Available Values: 1 ~ 10 Default Setting: 10 133 tAUd EQ3 BW Function: Adjusts the Q-factor of the high range of the parametric microphone equalizer. Available Values: 1 ~ 10 Default Setting: 10 128 tAUd EQ2 FRQ Function: Selects the center frequency of the middle range for the parametric microphone equalizer. Available Values: OFF / 700 ~ 1500 Hz (100 Hz/step) Default Setting: OFF OFF: The equalizer gain and Q-factor are set to factory defaults (flat). 700 ~ 1500: Center frequencies of 700 Hz ~ 1500 Hz. You may adjust the equalizer gain and Q-factor at this selected audio frequency via menu items "129 tAUd EQ2 LVL" and "130 tAUd EQ2 BW." 134 tAUd PE1 FRQ Function: Selects the center frequency of the lower range for the parametric microphone equalizer when the speech processor is activated. Available Values: OFF / 100 ~ 700 Hz (100 Hz/step) Default Setting: 200 Hz OFF: The equalizer gain and Q-factor are set to factory defaults (flat). 100 ~ 700: Center frequencies of 100 Hz ~ 700 Hz. You may adjust the equalizer gain and Qfactor at this selected audio frequency via menu items "135 tAUd PE1 LVL" and "136 tAUd PE1 BW." 129 tAUd EQ2 LVL Function: Adjusts the equalizer gain of the middle range of the parametric microphone equalizer. Available Values: ­20 ~ +10 Default Setting: +5 135 tAUd PE1 LVL Function: Adjusts the equalizer gain of the low range of the parametric microphone equalizer when the speech processor is activated. Available Values: ­20 ~ +10 Default Setting: 0 130 tAUd EQ2 BW Function: Adjusts the Q-factor of the middle range of the parametric microphone equalizer. Available Values: 1 ~ 10 Default Setting: 10 136 tAUd PE1 BW Function: Adjusts the Q-factor of the low range of the parametric microphone equalizer when the speech processor is activated. Available Values: 1 ~ 10 Default Setting: 2 Page 124 FT-2000 OPERATING MANUAL MENU MODE TX AUDIO GROUP 137 tAUd PE2 FRQ Function: Selects the center frequency of the middle range for the parametric microphone equalizer when the speech processor is activated. Available Values: OFF / 700 ~ 1500 Hz (100 Hz/step) Default Setting: 800 Hz OFF: The equalizer gain and Q-factor are set to factory defaults (flat). 700 ~ 1500: Center frequencies of 700 Hz ~ 1500 Hz. You may adjust the equalizer gain and Q-factor at this selected audio frequency via menu items "138 tAUd PE2 LVL" and "139 tAUd PE2 BW." TX GNRL GROUP 143 tGEn BIAS This Menu item does not work. Please do not change this setting. 144 tGEn MAX PWR Function: Selects a maximum output power limit. Available Values: 10 / 20 / 50 / 100 W Default Setting: 100 W 145 tGEn PWRCTRL Function: Configures the [RF PWR] knob. Available Values: ALL / CAr Default Setting: ALL ALL:The [RF PWR] knob is enabled on all modes. CAr: The [RF PWR] knob is enabled in all modes except SSB. In this configuration, the SSB output power will be set to maximum, regardless of the [RF PWR] knob's position. 138 tAUd PE2 LVL Function: Adjusts the equalizer gain of the middle range of the parametric microphone equalizer when the speech processor is activated. Available Values: ­20 ~ +10 Default Setting: 0 146 tGEn ETX-GND Function: Enables/Disables the TX GND jack on the rear panel. Available Values: EnA(ENABLE) / diS(DISABLE) Default Setting: diS(DISABLE) 139 tAUd PE2 BW Function: Adjusts the Q-factor of the middle range of the parametric microphone equalizer when the speech processor is activated. Available Values: 1 ~ 10 Default Setting: 1 147 tGEn TUN PWR Function: Selects a maximum output power limit for driving the input circuit of an external linear RF amplifier while tuning (while using the Remote Control function of the linear RF amplifier). Available Values: 10 / 20 / 50 / 100 W Default Setting: 100 W 140 tAUd PE3 FRQ Function: Selects the center frequency of the high range for the parametric microphone equalizer when the speech processor is activated. Available Values: OFF / 1500 ~ 3200 Hz (100 Hz/step) Default Setting: 2100 Hz OFF: The equalizer gain and Q-factor are set to factory defaults (flat). 1500 ~ 3200: Center frequencies of 1500 Hz ~ 3200 Hz. You may adjust the equalizer gain and Q-factor in this selected audio frequency via menu items "141 tAUd PE3 LVL" and "142 tAUd PE3 BW." 148 tGEn VOX SEL Function: Selects the audio input source for triggering TX during VOX operation. Available Values: nic / dAtA Default Setting: nic nic(MIC): The VOX function will be activated by microphone audio input. dAtA(DATA): The VOX function will be activated by data audio input. 141 tAUd PE3 LVL Function: Adjusts the equalizer gain of the high range of the parametric microphone equalizer when the speech processor is activated. Available Values: ­20 ~ +10 Default Setting: 0 149 tGEn EMRGNCY Function: Enables Tx/Rx operation on the Alaska Emergency Channel, 5167.5 kHz. Available Values: EnA(ENABLE) / diS(DISABLE) Default Setting: diS(DISABLE) When this Menu Item is set to "EnA(ENABLE)," the spot frequency of 5167.5 kHz will be enabled. The Alaska Emergency Channel will be found between the Memory channels "P-1" and "01 (or 1-01)." IMPORTANT: The use of this frequency is restricted to stations operating in or near Alaska, and only for emergency purposes (never for routine operations). See §97.401(c) of the FCC's regulations for details. 142 tAUd PE3 BW Function: Adjusts the Q-factor of the high range of the parametric microphone equalizer when the speech processor is activated. Available Values: 1 ~ 10 Default Setting: 1 FT-2000 OPERATING MANUAL Page 125