User manual MARANTZ CC4300 - PRODUCT MANUAL

R Model CC4300 User Guide 5 Disc CD Changer CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPON DANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call the CATV (Cable-TV) system installer's attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ ­ ­ ­ Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. NOTE: Changes or modifications may cause this unit to fail to comply with Part 15 of the FCC Rules and may void the user's authority to operate the equipment. LASER SAFETY This unit employs a LASER. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury. CAUTION-USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURE OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations. Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le materiel brouilleur du Canada. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. 1. Read Instructions ­ All the safety and operating instructions should be read before the product is operated. 2. Retain Instructions ­ The safety and operating instructions should be retained for future reference. 3. Heed Warnings ­ All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions ­ All operating and use instructions should be followed. 5. Cleaning ­ Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. Attachments ­ Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7. Water and Moisture ­ Do not use this product near waterfor example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. 8. Accessories ­ Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. 9. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 10.Ventilation ­ Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 11.Power Sources ­ This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12.Grounding or Polarization ­ This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 13.Power-Cord Protection ­ Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 14.Protective Attachment Plug ­ The product is equipped with an attachment plug having overload protection. This is a safety feature. See Instruction Manual for replacement or resetting of protective device. If replacement of the plug is required, be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug. 15.Outdoor Antenna Grounding ­ If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure 1. FIGURE 1 EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE, ANSI/NFPA 70 ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT(NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) NEC - NATIONAL ELECTRICAL CODE This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada. GROUND CLAMPS 16.Lightning ­ For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 17.Power Lines ­ An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 18.Overloading ­ Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 19.Object and Liquid Entry ­ Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 20.Servicing ­ Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 21.Damage Requiring Service ­ Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a.When the power-supply cord or plug is damaged. b.If liquid has been spilled, or objects have fallen into the product. c.If the product has been exposed to rain or water. d.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e.If the product has been dropped or damaged in any way, and f. When the product exhibits a distinct change in performance ­ this indicates a need for service. 22.Replacement Parts ­ When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 23.Safety Check ­ Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 24.Wall or Ceiling Mounting ­ The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 25.Heat ­ The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. Contents General Information ..................................................................................................................2 English Unpacking ...............................................................................................................................................................2 For Your Safety.......................................................................................................................................................2 Compact Discs........................................................................................................................................................3 Placement ...............................................................................................................................................................3 Functional Overview .................................................................................................................4 Front Panel Controls ...............................................................................................................................................4 Rear Panel Controls................................................................................................................................................6 Remote Control Unit (RC4300CC)..........................................................................................................................7 Connections...............................................................................................................................9 Connecting other Audio Equipment ........................................................................................................................9 Connecting the Remote Control............................................................................................................................10 Operations ...............................................................................................................................11 Playing CDs ..........................................................................................................................................................11 Changing Discs during Play..................................................................................................................................12 Skip and Search Play............................................................................................................................................12 Playing Tracks in Random Sequence (Random Play)..........................................................................................13 Playing the First 10 Seconds of Each Track (Introscan Play)...............................................................................13 Repeat Play ..........................................................................................................................................................14 Playing Tracks in Any Sequence (Programmed Play) ..........................................................................................14 Editing for Recording ............................................................................................................................................18 Deleted Play..........................................................................................................................................................22 Selecting a Brightness of the Display ...................................................................................................................24 Selecting a Time Display ......................................................................................................................................25 Using the Headphones .........................................................................................................................................25 External Control (Serial Interface) RS232C ..........................................................................................................26 Troubleshooting ......................................................................................................................28 Specifications ..........................................................................................................................29 1 General Information Unpacking English First check the contents of the packaging. It should contain the following: CD-Player CC4300 Remote control unit (RC4300CC) Batteries (AA size) x 2 Audio cable (1 - with red and white plugs) Remote control cable (with orange plugs) Instructions Guarantee Compact Discs The glossy side shining like a rainbow is the front side of the disc, and the side on which the label is printed is the back. Unlike conventional turntables for playing analog discs, the CC4300 reads the information recorded on the disc from underneath without contacting it using a beam of laser light. Therefore, the performance of a compact disc will not degrade like conventional analog records. Handle discs carefully so as not to damage or scratch the front side. To protect the disc, avoid placing it in the following locations: · In direct sunlight or near a source of heat like a heater. · In a place which is damp or dirty. · In a place which could be exposed to rain, such as near a window. Always keep the disc surface clean. Up to six billion data units are recorded on the front side of the disc. When cleaning the disc surface, always be sure to use a special compact disc cleaner and wipe as shown below. If one of these components is missing, please inform your supplier immediately. Save the packaging material it may come in handy if you move the appliance. For Your Safety Units shipped to the U.S.A. and Canada are designed for operation on 120 V AC only. Safety precaution with use of a polarized AC plug. However, some products may be supplied with a nonpolarized plug. CAUTION : To prevent electric shock, match wide blade of plug to wide slot, fully insert. · Do not use conventional record cleaner for analog records, as this will adversely affect the disc surface. Store discs properly by placing them in their disc cases. · Do not attach a piece of paper or sticker on the label side of disc. When a disc has a piece of plastic tape or rental CD label with paste protruded from the edge or when a disc has a trace of such a sticky object, do not attempt to play the disc. If such a disc is played on the CD player, impossibility of taking out the disc or other malfunction may result. · Write only on the printed side of a CD-R or CDRW, and only with a soft felt-tipped pen. · Do not use a disc with a special shape. Do not attempt to play a disc with a special shape such as a heart-shaped disc or octagonal disc. Otherwise the equipment malfunction may result. 2 General Information Playing CD-RW discs This unit can play back the CD-RW (ReWritable) discs as well as ordinary music CD and CD-R (Recordable) discs. · The CD-R and CD-RW discs should contain properly-recorded TOC information so that they can be played back. With the CD recorder system, writing the TOC information in a disc is referred to as finalizing the disc. A disc cannot be recognized as a CD disc and played back unless it has been finalized properly. For details, please read the instruction manual provided with a CD recorder. · TOC stands for Table Of Contents and contains information such as the total number of tracks and total playing time of the disc. · This unit can play only the discs recorded in the CD-DA format designed for music reproduction. Do not attempt to play a disc containing other data, such as a CD-ROM for PCs, on this unit. · As the playback of a CD-RW disc necessitates partial change of the player setup, it may take longer time for reading the TOC information than when a music CD or CD-R disc is played. · A few CD-RW discs may not be played in some reason. Please use another disc to play. Placement English · Place the CD player on a firm, flat surface. · Keep away from domestic heating equipment and direct sunlight. · In a cabinet, allow about 2 inches of free space all around the player for adequate ventilation. · If the CD player cannot read CDs correctly, use a commonly-available cleaning CD to clean the lens before taking the CD-player to be repaired. Other cleaning methods may destroy the lens. Always keep the tray closed to avoid dust on the lens. · When it is moved from a cold to a warm environment, allow the CD player to acclimatize for at least 2 hours in order to avoid damage. When suddenly placed in a warm environment, the lens may cloud over. Playing an CD will not be possible then. Wait until the moisture evaporates. · Do not use the CD player under extremely damp conditions. · Do not expose discs to direct sunlight, high humidity or high temperature for a long time. Attention! If the appliance is not used or operated in accordance with the instructions, this may result in exposure to dangerous radiation or other risks. Only authorized technicians are allowed to open the appliance casing or to perform repairs or maintenance. 3 Functional Overview Front Panel Controls English 1 2 3 4 5 6 OPEN/CLOSE 5DISC CD CHANGER CC4300 1 2 3 4 5 DISC SKIP DISC CHANGER STANDBY EDIT T.SIZE TIME PROG DELETE AUTO EDIT A B POWER ON/STANDBY RANDOM RANDOM REPEAT ALL 1 DISCS A< >B INTRO INDEX STEP SCENE TRACK PROGRAM DELETE INTRO 1 2 3 4 5 1 23 4 56 7 89 10 11 12 13 14 PHONES / LEVEL REPEAT 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 q POWER ON/STANDBY button Press this switch to turn the power on and press again to turn to stand by. !0 DELETE button Press this button to delete the undesired tracks, discs or review the deleted selections. w STANDBY indicator Lights up red when the CD player is in Stand-by mode. !1 INTRO (Introscan) button Press this button to play the first 10 seconds of each track on CDs. e Disc tray Load a compact disc on the disc tray. !2 TIME button Press this button to display the elapsed or remaining playing time of the current track or remaining playing time of the disc. r Disc selector buttons Use these buttons to select the disc to be played. t DISC SKIP button For loading or unloading discs, press this button to rotate clockwise to the next disc position. !3 Fluorescent display For details, refer to the next page. !4 RANDOM button Press this button to play tracks on CDs in random sequence. y OPEN/CLOSE button (/) Press this button to open or close the disc tray. u EDIT button Press this button to edit the tracks to be recorded onto the tape. !5 REPEAT button Press this button to play a track, a disc or all discs repeatedly. i PROGRAM button Press this button to program your favorite tracks, disc or review the programmed selections. !6 9 (Stop/Clear) button Press this button to stop play, clear the programmed selections or recover the deleted selections. o T. SIZE (Tape size) button Use this button to select the tape length in edit recording. !7 (Backward skip/Search) button · Press this button to replay from the beginning of the current track or return to a previous track. · Press and hold down this button to search for a specific passage in fast backward. 4 Functional Overview !8 § (Forward skip/Search) button English E F G RANDOM REPEAT ALL 1 DISCS A< . >B INTRO INDEX STEP · Press this button to play from the beginning of a next track. · Press and hold down this button to search for a specific passage in fast forward. !9 2 / ; (Play/Pause) button · Press this button to start playing in the stop or pause mode. · Press this button to interrupt play temporarily and press again to restart play. @0 PHONES jack Stereo headphones can be plugged into this jack for private listening. @1 LEVEL knob Turning the control clockwise increases the headphone level. Turning the control counterclockwise decreases the headphone level. Fluorescent Display A B C D PROG DELETE AUTO EDIT A B SCENE TRACK 1 2 3 4 5 : 12 45 78 10 11 13 14 3 6 9 12 H I J K L M A Disc number display B DELETE indicator C PROGRAM indicator D EDIT display E RANDOM PLAY indicator F REPEAT indicator G Indicators for Repeat, Introscan and Random play mode H PLAY indicator I PAUSE indicator J Track number and Time display K REPEAT A<.>B indicator L INTROSCAN indicator M Music calendar display 5 Functional Overview Rear Panel Controls English REMOTE CONTROL SELECTOR DIGITAL OUT COAX. OPTICAL EXT. INT. R OUT 1 2 RS232C ANALOG OUT L REMOTE CONTROL IN 4 5 6 3 7 z ANALOG output jacks Connect these jacks to the CD(or AUX) input jacks of your amplifier or receiver. b DIGITAL output (COAX.) jack · Connect this jack to the COAXIAL DIGITAL input jack of amplifier or receiver to enjoy live digital sound. · You can record digital sound by connecting the COAXIAL DIGITAL INPUT jack of MD deck or CD recorder to this jack. x RS232C The RS232C port is to be used in conjunction with an external controller to control the operation of the CD player by using an external device. (See also page 26.) n DIGITAL output (OPTICAL) jack · Connect this jack to the OPTICAL DIGITAL input jack of amplifier or receiver to enjoy live digital sound. · You can record digital sound by connecting the OPTICAL DIGITAL INPUT jack of MD deck or CD recorder to this jack. · Not all of the commercially-available optical fiber cords can be used for audio equipment. If there is an optical fiber cord which cannot be connected to your audio equipments, consult your dealer or nearest service organization. c REMOTE CONTROL IN/OUT jacks By connecting this CD player to another Marantz audio component using a D-BUS remote control cable, you can operate the components remotely as a single system. · When connecting to a component with a remote sensor, connect the REMOTE CONTROL IN jack of this unit to the REMOTE CONTROL OUT jack of the component with the remote sensor. · When connecting to a component which is not equipped with a remote sensor, connect the component to the REMOTE CONTROL OUT jack of this unit. For the D-BUS cable connection, use supplied remote control cable or a commercially available RCA-type pin lead. · By connecting this CD player to a Marantz auto reverse cassette deck (such as the SD4050), automatic recording from the CD player to the cassette deck can be carried out. m AC input cord Plug this cord into a wall AC outlet or the switched AC outlet of amplifier or receiver. v REMOTE CONTROL SELECTOR switch When using this unit independently, set this switch to INTERNAL. When using this unit in a system incorporating a Marantz other equipments with a remote sensor, set the switch to EXTERNAL. Note : · Always set this switch to INTERNAL unless the unit is connected with other MARANTZ equipment through a system connection. When this switch is set to EXTERNAL, the main unit cannot be controlled from the provided remote control unit. 6 Functional Overview Remote Control Unit (RC4300CC) o 6 (Search) button English Press and hold down this button to search for a specific passage in fast forward. DISC POWER 1 2 3 4 5 7 6 8 10 11 !0 TIME button Press this button to display the elapsed or remaining playing time of the current track or remaining playing time of the disc. 12 REPEAT 1 2 5 8 0 3 A-B 13 14 15 17 19 20 16 18 4 7 PROGRAM 6 RANDOM 9 DELETE INTRO !1 DIMMER button Press this button to change the brightness of the display. !2 DISC button When selecting a disc with this button, press this first and then the desired disc number(1~5) on the numeric buttons within 2 seconds. EDIT T.SIZE DIMMER TIME 9 REMOTE CONTROL UNIT RC4300CC !3 NUMERIC buttons Press the corresponding button when selecting tracks or discs for play, programming or deleting, then the selected track is played, programmed or deleted directly without use of the PLAY, PROGRAM/REVIEW or DELETE/REVIEW button. · When selecting a two digit number, the second digit should be pressed within 2 seconds after the first digit has been pressed !4 PROGRAM button q POWER button Press this button to turn the power on and press again to turn to stand by. Press this button to program your favorite tracks, disc or review the programmed selections. !5 ; (Pause) button Press this button to interrupt play temporarily and press again to restart play. w REPEAT button Press this button to play a track, a disc or all discs repeatedly. !6 2 (Play) button Press this button to start play in the stop or pause mode. e A<.>B button Press this button to play a specific passage repeatedly. !7 § (Forward skip) button Press this button to play from the beginning of a next track. r RANDOM button Press this button to play tracks on CDs in random sequence. !8 (Backward skip) button Press this button to replay from the beginning of the current track or return to a previous track. t INTRO (Introscan) button Press this button to play the first 10 seconds of each track on CDs. !9 EDIT button Press this button to edit the tracks to be recorded onto the tape. y DELETE button Press this button to delete the undesired tracks, discs or review the deleted selections. @0 T. SIZE (Tape size) button Use this button to select the tape length in edit recording. u 9 (Stop/Clear) button Press this button to stop play, clear the programmed selections or recover the deleted selections. i 5 (Search) button Press and hold down this button to search for a specific passage in fast backward. 7 Functional Overview Operation of Remote Control Unit 1. Remote control The distance between the transmitter of the remote control unit and the IR SENSOR of the CC4300 should be less than about 5 meters. If the transmitter is pointed to a direction other than the IR SENSOR or if there is an obstacle between them, remote control may not be possible. Remote-controllable range English 2. Loading batteries The life of the batteries used with the remote control unit is about 6 months with normal use. Also be sure to replace batteries earlier when you notice that they are getting weak. 1. Remove the back cover. CC4300 rs p Ap rox 5 te me 60 ° Note : · Remove the batteries when they are not used for a long time. · Do not use the rechargeable batteries(Ni-Cd type). 2. Insert the new batteries (AA size) with correct (+) and (­) polarity. RC4300CC 3. Close until it clicks. 8 Connections Precautions concerning connections : · Do not plug the AC input cord into the AC outlet when plugging and unplugging connection cords. · Be sure to connect the white plugs to the L(Left) and the red plugs to the R(Right) jacks when making connections with the supplied cords. · Plug the optical digital cable in securely, as far as it will go. · Refer to the connecting diagram in the operating instructions of AMPLIFIER/RECEIVER. English Connecting other Audio Equipment CC4300 RS232C REMOTE CONTROL SELECTOR DIGITAL OUT COAX. OPTICAL ANALOG OUT L REMOTE CONTROL IN EXT. INT. R OUT R L R L DIGITAL INPUT COAXIAL DIGITAL INPUT OPTICAL R AUDIO IN L RS232C External Controller Amplifier / Receiver 9 Connections Connecting the Remote Control English CC4300 RS232C REMOTE CONTROL SELECTOR DIGITAL OUT COAX. OPTICAL ANALOG OUT L REMOTE CONTROL IN EXT. INT. R OUT EXT. INT. OUT IN REMOTE CONTROL REMOTE CONTROL Cassette Deck Amplifier / Receiver 10 Operations Playing CDs 1. Press the POWER ON/STANDBY button on the unit or the POWER button on the remote control to turn on the power. STANDBY 7 PROGRAM 8 0 9 DELETE INTRO or or DISC POWER EDIT T.SIZE DIMMER TIME POWER ON/STANDBY REPEAT 1 4 2 5 3 A-B 6 · " ; " indicator lights up. · Press Play/Pause button on the unit again or the Play button on the remote control to restart play. 5. Press Stop/Clear button on the unit or the Stop/Clear button on the remote control to stop play. · Each time the POWER ON/STANDBY (or POWER ) button is pressed, this unit is turned on or off. 2. Press the OPEN/CLOSE button on the unit to open the disc tray. Load the disc(s) and close the disc tray. OPEN/CLOSE 7 PROGRAM 8 0 9 DELETE INTRO or EDIT T.SIZE DIMMER TIME · " \ " indicator lights up when the number of tracks is more than 14. · For loading discs on other trays each, press the DISC SKIP button on the unit. · 8cm(3 inches) CDs can be loaded on the inside circle of the tray, too. Note Do not open or close the tray by force. Doing so may damage it. - Display in Stop Mode Music calendar PROG DELETE AUTO EDIT A B SCENE TRACK RANDOM REPEAT ALL 1 DISCS A< . >B INTRO INDEX STEP 1 2 3 4 5 12 45 78 10 11 13 14 3 6 9 12 Total tracks 3. Press Play/Pause button on the unit or the Play button on the remote control to start play. 7 PROGRAM Total playing time 8 0 9 DELETE INTRO or EDIT T.SIZE DIMMER TIME · " 2 " indicator lights up. · The unit plays from the first track on the 1st disc to the last track on the 5th disc. 11 English 4 To interrupt play temporarily, press Play/Pause button on the unit again or the Pause button on the remote control. Operations Changing Discs during Play English 1. Press the OPEN/CLOSE button on the unit to open the disc tray. OPEN/CLOSE Skip and Search Play Selecting a Disc · Press the corresponding Disc selector button on the unit to start play from the desired disc. · Press DISC button on the remote control first and then the desired disc number(1~5) on the NUMERIC buttons within 2 seconds. (Example) When selecting the disc 3. 1 2 3 4 5 2. Change the desired discs. DISC POWER REPEAT or 1 4 7 2 5 8 3 A-B 6 RANDOM 9 · The first track of selected disc will be played. Disc tray · During playing the disc q, the discs e and r can be changed. · After changing the discs, press the OPEN/CLOSE button on the unit to close the disc tray. · When changing the disc w or t, press the DISC SKIP button on the unit and rotate the disc tray. Searching for a Passage during Play · Press and hold down / § buttons on the unit or the 5 / 6 button on the remote control until the desired passage is reached. or EDIT T.SIZE DIMMER TIME REMOTE CONTROL UNIT RC4300CC Selecting a Track during Play · Press / § buttons on the unit or the / § button on the remote control momentarily and repeatedly until the desired track is selected. or EDIT T.SIZE DIMMER TIME REMOTE CONTROL UNIT RC4300CC · When using the NUMERIC buttons on the remote control. (Example) When selecting "9" : 9 When selecting "22" : 2 2 within 2 sec. 12 Operations 1 Disc Random Play · Press RANDOM button on the unit or the RANDOM button on the remote control to play tracks in random sequence. RANDOM 1 Disc Introscan Play · Press INTRO button on the unit or the INTRO button on the remote control to play the first 10 seconds of each track. INTRO 1 4 2 5 8 0 3 A-B 4 6 7 RANDOM 5 8 0 6 RANDOM 9 DELETE INTRO or 7 PROGRAM 9 DELETE INTRO or PROGRAM · "RANDOM" indicator lights up. · The unit automatically selects and plays tracks on the current disc in random sequence. · "INTRO" indicator lights up. · The unit plays the first 10 seconds of each track from the current disc to the 5th disc. All Discs Random Play · In the 1 disc random play mode, press RANDOM button again. · The unit automatically selects a disc among five discs and a track on that disc in random sequence and plays it. · After that track has been played, the unit continues to select another disc and a track on that disc in random sequence and plays it. · Press RANDOM button again to cancel the random play. · Each time RANDOM button is pressed, the random play mode changes as follows: RANDOM 1 DISC RANDOM ALL DISCS OFF All Discs Introscan Play · In the 1 disc introscan play mode, press INTRO button again. · The unit plays the first 10 seconds of each first track from the current disc to the last disc. · Press INTRO button again to cancel the introscan play. · Each time INTRO button is pressed, the introscan play mode changes as follows: INTRO 1 DISC INTRO ALL DISCS OFF 13 English Playing Tracks in Random Sequence (Random Play) Playing the First 10 Seconds of Each Track (Introscan Play) Operations Repeat Play English Repeating a Single Track during Play · Press REPEAT button on the unit or the REPEAT button on the remote control after selecting the desired track. REPEAT Playing Tracks in Any Sequence (Programmed Play) Note : · Up to 32 selections can be programmed to play in any desired sequence. · The track number greater than 99 can not be memorized. DISC POWER REPEAT 1 2 5 8 3 A-B Programming the Tracks on the CDs 1. In the stop mode, enter the program mode. Press PROGRAM button on the unit or the PROGRAM button on the remote control. PROGRAM or 4 7 PROGRAM 6 RANDOM 9 DELETE INTRO RANDOM Repeating a Disc during Play · After selecting the desired disc, press REPEAT button again in the 1 track repeat mode. or 7