LCD MONITOR quick start guide 2443NW 2443NWX Introduction Package Contents Note Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Type 1 Monitor & Simple stand Type 2 Monitor & USB Simple stand Note MagicRotation program can not be provided as Simple Stand does not support Pivot function. Type3 Monitor & HAS stand Introduction Type4 Monitor & USB HAS stand Manuals Quick Setup Guide Warranty Card (Not available in all locations) User's Guide Cables D-Sub Cable Others Power Cord Cleaning Cloth Cable holding ring (Simple stand) Sold separately USB Cable Note This is only provided for highly polished black products as a product feature. Introduction Your Monitor Initial Settings Select the language using the up or down key. The displayed content will disappear after 40 seconds. Turn the Power button off and on. It will be displayed again. It can be displayed up to three (3) times. Make sure to adjust the resolution of your PC before reaching the maximum count. Note The resolution displayed on the screen is the optimal resolution for this product. Adjust your PC resolution so that it is the same as the optimal resolution for this product. Front MENU button [MENU/ ] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Customized Key[ ] Introduction You can customize key assignment for the Custom button according to your preferences. Note You can configure the customized key for a required function via Setup > Customized Key. Brightness button [ ] When OSD is not on the screen, push the button to adjust brightness. >> Click here to see an animation clip Adjust buttons [ ] These buttons allow you to adjust items in the menu. Enter button [ ] Activates a highlighted menu item. AUTO button Use this button for auto adjustment. >> Click here to see an animation clip Power button [ ] Use this button for turning the product on and off. Power Indicator This light is lit when operating normally, and blinks once when your adjustments are saved. Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended for long periods. Rear Note The configuration at the back of the product may vary from product to product. Simple Stand HAS Stand Introduction POWER port Connect the power cord for your monitor to the POWER port on the back of the product. RGB IN port Connect the D-sub cable to the 15-pin, RGB IN port on the back of your monitor. Kensington Lock The Kensington lock is a device used to physically fix the system wheng it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact where you purchase it. DOWN(USB downstream port) Connect the cable. DOWN port of the USB monitor and a USB device with the USB UP(USB upstrem port) Connect the USB cable. Note See Connecting Cables for further information regarding cable connections. UP port of the monitor and the USB port of the computer with the Cable holding ring · Fix the cables using the holding ring, as shown in the figure. Connections Connecting Cables Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the RGB IN(Analog) connector on the video card. · Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [RGB IN] Connected to a Macintosh. · Connect the monitor to the Macintosh computer using the D-sub connection cable. Note If the monitor and the computer are connected, you can turn them on and use them. Connecting USB (Option) Note You can use a USB device such as a mouse, keyboard, Memory Stick, or external hard disk drive by connecting them to the The DOWN port of the monitor without connecting them to the PC. USB port of the monitor supports High-Speed Certified USB 2.0. High speed Full speed 12 Mbps 2.5 W (Max., each port) Low speed 1.5 Mbps 2.5 W (Max., each port) Data Rate 480 Mbps (Max., each port) Power Consumption 2.5 W Connections 1. Connect the Note To use UP port of the monitor and the USB port of the computer with the USB cable. DOWN port, you have to connect the UP (Upstream Cable) to the PC. UP port Make sure to use the USB cable supplied with this monitor to connect the monitor's and your computer's USB port. 2. 3. Connect the DOWN port of the USB monitor and a USB device with the USB cable. The use procedures are as the same as those for using an external device connecting to the PC. · · You can connect and use a keyboard and mouse. You can play a file from a media device. (Examples of media devices: MP3, digital camera, etc.) · You can run, move, copy or delete the files on the storage device. (Examples of storage devices: external memory, memory card, memory reader, HDD-type MP3 player, etc.) · You can use other USB devices that can be connected to a computer. Note When connecting a device to the cable appropriate to the device. DOWN port of the monitor, connect the device using a (For the purchase of the cable and external devices, ask the service center of the corresponding product.) Connections The company is not liable for problems or damages to an external device caused by using an unauthorized cable for the connection. Some products do not follow the USB standard, and it may cause a malfunction of the device. If the device malfunctions even if it is connected to the computer, contact the service center of the device/computer. Using the Stand Monitor Assembly Simple Stand Monitor and Bottom HAS Stand A. Stand Stopper Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad. Connections Simple Stand A. Monitor B. Mounting interface pad (Sold separately) 1. 2. 3. 4. Turn off your monitor and unplug its power cord. HAS Stand Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. Remove two screws and then remove the stand from the LCD monitor. Align the mounting interface pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base. · · · Do not use screws longer than the standard dimension, as they may damage the inside of the Monitor. For wall mounts that do not comply with VESA standard screw specifications, the length of the screws may differ depending on their specifications. Do not use screws that do not comply with the VESA standard screw specifications. Do not fasten the screws too tightly, as this may damage the product or cause the product to fall, leading to personal injury. Samsung is not liable for these kinds of accidents. · Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions. To mount the monitor on a wall, you should purchase the wall mounting kit that allows you to mount the monitor at least 10 cm away from the wall surface. Contact the nearest Samsung Service Center for more information. Samsung Electronics will not be responsible for damages caused by using a base other than those specified. Please use Wall Mount according to the International standards. · · · Troubleshooting Self-Test Feature Check Note Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check 1. 2. 3. Turn off both your computer and the monitor. Unplug the video cable from the back of the computer. Turn on the monitor. If the monitor is functioning properly, you will see a box in the illustration below. This box appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly. Warning Messages If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable. Environment The location and the position of the monitor may influence the quality and other features of the monitor. If there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. Useful Tips A monitor recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the monitor to become blank, have poor coloring, become Troubleshooting noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact the Service Center or your dealer. Judging the monitor's working condition If there is no image on the screen or a "Not Optimum Mode", "Recommended Mode 1920 x 1200 60 Hz" message comes up, disconnect the cable from the computer while the monitor is still powered on. If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. In this case, check the computer for trouble. Check List Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. No images on the screen. I cannot turn on the monitor. Q: A: Q: A: Is the power cord connected properly? Check the power cord connection and supply. Can you see "Check Signal Cable" on the screen? (Connected using the D-sub cable) Check the signal cable connection. Q: A: If the power is on, reboot the computer to see the initial screen (the login screen), which can be seen. If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card. (Refer to the Preset Timing Modes) If the initial screen (the login screen) does not appear, contact the Service Center or your dealer. Q: A: A: A: Can you see "Not Optimum Mode", "Recommended Mode 1920 x 1200 60 Hz" on the screen? You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. Adjust the maximum resolution and frequency that the monitor can handle properly. If the display exceeds SXGA or 75 Hz, a "Not Optimum Mode", "Recommended Mode 1920 x 1200 60 Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly but the "Not Optimum Mode", "Recommended Mode 1920 x 1200 60 Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.) Troubleshooting Q: A: A: A: There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode. Press a key on the keyboard to activate the monitor and restore the image on the screen. If there is still no image, press the ' ' button. Then press any key on the keyboard again to activate the monitor and restore the image on the screen. I cannot see the On Screen Display. Q: A: Have you locked the On Screen Display (OSD) Menu to prevent changes? Unlock the OSD by pressing the [MENU/ ] button for at least 5 seconds. The screen shows strange colors or just black and white. Q: A: A: Q: A: Q: A: Is the screen displaying only one color as if looking at the screen through a cellophane paper? Check the signal cable connection. Make sure the video card is fully inserted in its slot. Have the screen colors become strange after running a program or due to a crash between applications? Reboot the computer. Has the video card been set properly? Set the video card by referring to the video card manual. The screen suddenly has become unbalanced. Q: A: Q: A: Have you changed the video card or the driver? Adjust screen image position and size using the OSD. Have you adjusted the resolution or frequency to the monitor? Adjust the resolution and frequency at the video card. (Refer to the Preset Timing Modes). Q: The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD. The screen is out of focus or OSD cannot be adjusted. Q: A: Have you adj ...