User manual NAVMAN A300 - QUICK START GUIDE

NAVMAN A300 -- Settings Setting options Press and hold to enter setup Press repeatedly to step through the setting options. ) to start or stop editing Press both buttons together ( a setting option. repeatedly to step through selectable states, or While editing, press or increase/decrease values. Press and hold the appropriate button to increase/decrease values quickly. Set (12hr) lets you set 12hr or 24hr time format Set (31-12) lets you set dd-mm or mm-dd date format Calc up When `calc up' is «ON» the A300 calculates data for all movement (uphill and downhill). When `calc up' is «OFF» the A300 calculates information for downhill movement only. Beep When beep is «ON» a beep will sound when the buttons are pushed. Set units (km/h) lets you set speed units to «km/h» or «mph» Distance and altitude are displayed in units corresponding to the speed units, i.e. if you choose «km/h» for speed units, then distance is displayed in «km» and altitude in «m». Set offset lets you adjust the A300 to display local time The date is displayed to ensure that time adjustments are made in the correct direction, i.e. both correct time and correct date should be displayed. GPS signals must be obtained to set local time. Press and hold to leave setup A300 NAVMAN A300 -- Settings Use the settings settings editing details edit set (12hr) set (12hr) set 12hr set 24hr accept set (31-12) edit set (31-12) set 31-12 set 12-31 accept Calc up edit Calc up Calc up ON Calc up OFF accept beep edit beep beep ON beep OFF accept set units (km/h) edit set units (km/h) set units (km/h) accept set units (mph) set offset edit accept time (date) KEY = press this button = press this button = press both buttons together A300 NAVMAN A300 -- Modes Normal operating modes Press to start normal operation to Press repeatedly to step through the modes (hold cycle automatically through modes). Speed shows session distance and current speed Speed (AVG) shows session distance and average speed Speed (MAX) shows session distance and maximum speed Odometer shows total distance Altitude shows total accumulated altitude and current altitude Clock shows the current time and date (You may need to adjust the settings to display your local time) Timer shows session and lap times The timer starts automatically whenever you start moving and stops whenever you stop moving. Timer Recall lets you recall stored lap data. Repeatedly pressing recalls lap data starting from the last stored lap, then lap 1, 2, 3 etc. Press and hold to shut down the A300 A300 NAVMAN A300 -- Modes Use the modes modes Speed operating details store current lap data clear all* session data store current lap data clear all* session data store current lap data clear max speed only store current lap data clear odometer only store current lap data clear accumulated altitude only store current lap data clear all* session data store current lap data clear all* session data recall lap data restart recall from lap 1 (*Does not clear odometer) * AVG Speed (AVG) * MAX Speed (MAX) * 2 87 3 Odometer * Altitude * Clock * Timer * RCL Timer recall * KEY = press this button = press this button = press both buttons together = press and hold both buttons together A300 A300 QUICK START GUIDE NOW YOU KNOW. A300 Step 1 Get ready Fit the battery ! For best performance: General use = Alkaline Below 5 oC = NiMH 1. Turn D-ring anti-clockwise and slide enclosure cover down to open battery enclosure. 2. Insert battery with «» end as indicated inside enclosure. 3. Replace enclosure cover (ensuring lugs at the bottom of the cover are aligned with slots in the enclosure surround), turn D-ring clockwise to seal. Fit the A300 The A300 is designed to be worn on the left upper arm. You may wish to adjust some of the settings prior to fitting. L Be outdoors The A300 is not intended for operation indoors or under water as it uses Global Positioning System (GPS) satellites to get time and date information, and to calculate distance and speed. For best results, always use the A300 outdoors with an unobstructed view of the sky. A300 Step 2 Get set Know the buttons The control buttons, and (as shown above) are pressed separately or together to turn the unit «ON» and «OFF», cycle through modes, and select mode options. Know the startup options 1. enter setup 2. start normal operation ! Always enter setup first if you wish to change settings. To enter setup after starting normal operation, you must shut down and re-start the A300. Flashing icon = seeking GPS signals Constant icon = GPS signals obtained Startup could take up to 80 seconds to get all satellite data. Enter setup Press and hold to enter setup counter If you release before the counter reaches zero, the A300 will immediately start normal operation. For details about system settings see over page or consult User Guide. Press and hold to leave setup counter After leaving setup, the A300 automatically starts normal operation displaying the speed mode first. A300 Step 3 Go Start normal operation Press to start normal operation When starting directly into normal operation A300 will start in the mode it was in at last shutdown. The A300 automatically operates whenever you are moving and pauses operation while you are stationary. Modes are accessed in the following order: 2 3 AVG MAX 87 Speed Timer RCL RCL Speed AVG Timer Speed MAX Clock Odometer Altitude For details about modes see over page or consult User Guide. Mode example (speed) current speed session distance speed mode icon Mode icons appear in the lower section of the screen. While in Speed mode you can monitor session distance and current speed. You can also store laps and clear session data. While in Speed mode Press to store lap data Press and hold to clear all* session data Press to go to next mode (*Does not clear odometer) When you want to shut down the A300 Press and hold Now you know A300 LA000525B © 2005 Navman NZ Ltd. All rights reserved. Sport.Tool' and `Now you know.' are trademarks of Navman NZ Ltd.