NAVMAN M300 -- Settings NAVMAN M300 -- Settings NAVMAN M300 -- Modes NAVMAN M300 -- Modes Setting options Press and hold to enter setup Press repeatedly to step through the setting options. ) to start or stop editing Press both buttons together ( a setting option. repeatedly to step through selectable states, or While editing, press or increase/decrease values. Press and hold the appropriate button to increase/decrease values quickly. Use the settings settings edit Normal operating modes Press set 12hr set 24hr accept Use the modes modes operating details store current lap data clear all session data* store current lap data clear all session data* store current lap data clear max speed only store current lap data clear odometer only store current lap data store current lap data clear all session data* store current lap data clear all session data* editing details to start normal operation to set (12hr) set (12hr) Press repeatedly to step through the modes (hold cycle automatically through modes). Speed shows session distance and current speed Speed AVG Speed (AVG) set (31-12) edit set (31-12) set 31-12 set 12-31 accept Speed (AVG) shows session distance and average speed Speed (MAX) shows session distance and maximum speed MAX Speed (MAX) Set (12hr) lets you set 12hr or 24hr time format Set (31-12) lets you set dd-mm or mm-dd date format Beep When beep is «ON» a beep will sound when the buttons are pushed. Set units (knots) lets you set speed units to «knots», «km/h» or «mph» Distance is displayed in units corresponding to the speed units, i.e. if you choose «knots» for speed units, then distance is displayed in nautical miles. beep edit 2 873 beep beep ON beep OFF set units (knots) accept Odometer mode shows total distance from last odometer reset Heading mode shows current heading in degrees from true North Odometer Heading N S set units (knots) edit set units (knots) set units (km/h) accept Clock shows the current time and date (You may need to adjust the settings to display your local time.) Clock Timer set units (mph) edit accept Timer shows session and lap times The timer starts automatically whenever you start moving and stops whenever you stop moving. RCL Timer recall Set offset lets you adjust the M300 to display local time The date is displayed to ensure that time adjustments are made in the correct direction, i.e. both correct time and correct date should be displayed. GPS signals must be obtained to set local time. set offset time (date) recall lap data restart recall from lap 1 (*does not clear odometer) Timer Recall lets you recall stored lap data. Repeatedly pressing recalls lap data starting from the last stored lap, then lap 1, 2, 3 etc. Press and hold to shut down the M300 QUICK START GUIDE Press and hold to leave setup KEY = press this button = press this button = press both buttons together * KEY = press this button = press this button = press both buttons together = press and hold both buttons together Step 1 Step 2 Step 3 Get ready Fit the battery Get set Know the buttons Go Start normal operation © 2005 Navman NZ Ltd. All rights reserved. "Sport.Tool" and "Now you know" are trademarks of Navman NZ Ltd. LA000530A ! For best performance: General use = Alkaline Below 5 oC = NiMH Press to start normal operation The control buttons, and (as shown above) are pressed separately or together to turn the unit «ON» and «OFF», cycle through modes, and select mode options. Know the startup options 1. enter setup 2. start normal operation When starting directly into normal operation M300 will start in the mode it was in at last shutdown. The M300 automatically operates whenever you are moving and pauses operation while you are stationary. Modes are accessed in the following order: AVG MAX 1. Turn D-ring anti-clockwise and slide enclosure cover down to open battery enclosure. 2. Insert battery with «» end as indicated inside enclosure. 3. Replace enclosure cover (ensuring lugs at the bottom of the cover are aligned with slots in the enclosure surround), turn D-ring clockwise to seal. ! Always enter setup first if you wish to change settings. To enter setup after starting normal operation, you must shut down and re-start the M300. Speed Timer RCL RCL Speed AVG Timer Speed MAX Clock 2 873 Odometer Heading N S Fit the M300 The M300 is designed to be worn on the left upper arm. You may wish to adjust some of the settings prior to fitting. Flashing icon = seeking GPS signals Constant icon = GPS signals obtained Startup could take up to 80 seconds to get all satellite data. For details about modes, see over page or consult User Guide. Mode example (speed) current speed session distance nmi knots Enter setup L NOW YOU KNOW. Press and hold to enter setup counter speed mode icon Be outdoors The M300 is not intended for operation indoors or under water as it uses Global Positioning System (GPS) satellites to get time and date information, and to calculate distance and speed. For best results, always use the M300 outdoors with an unobstructed view of the sky. If you release before the counter reaches zero, the M300 will immediately start normal operation. For details about system settings see over page or consult User Guide. Mode icons appear in the lower section of the screen. While in Speed mode you can monitor session distance and current speed. You can also store laps or clear session data. While in Speed mode Press to store lap data Press and hold to clear all* session data (*does not clear odometer) Press to go to next mode When you want to shut down the M300 Press and hold to leave setup counter After leaving setup, the M300 automatically starts normal operation displaying the speed mode first. Press and hold Now you know. ...