User manual NAVMAN S300 - QUICK START GUIDE

NAVMAN S300 -- Settings Setting options Press and hold to enter setup Press repeatedly to step through the setting options. ) to start or stop Press both buttons toghether ( editing a setting option. repeatedly to step through selectable states, or While editing, press or increase/decrease values. Press and hold the appropriate button to increase/decrease values quickly. Set (12hr) lets you set 12hr or 24hr time format Set (31-12) lets you set dd-mm or mm-dd date format Beep When beep is «ON» a beep will sound when the buttons are pushed. Set units (km/h) lets you set speed units to «km/h» or «mph» Distance is displayed in units corresponding to the speed units, i.e. if you choose «km/h» for speed units, then distance is displayed in «km». Set offset lets you adjust the S300 to display local time The date is displayed to ensure that time adjustments are made in the correct direction, i.e. both correct time and correct date should be displayed. GPS signals must be obtained to set local time. Press and hold to leave setup S300 NAVMAN S300 -- Settings Use the settings settings edit editing details set 12hr set 24hr accept set (12hr) set (12hr) set (31-12) edit set (31-12) set 31-12 set 12-31 accept beep edit beep beep ON beep OFF accept set units (km/h) edit set units (km/h) set units (km/h) accept set units (mph) edit accept set offset time (date) KEY = press this button = press this button = press both buttons together S300 NAVMAN S300 -- Modes Normal operating modes Press to start normal operation to Press repeatedly to step through the modes (hold cycle automatically through modes). Speed shows session distance and current speed Speed (AVG) shows session distance and average speed Speed (MAX) shows session distance and maximum speed Odometer shows total distance Zone OFF lets you skip the zone setting options Zone alerts do not sound if zone status is «OFF». Zone ON makes the min and max zone setting options available If zone status is «ON», alerts sound when zone limits are passed. Zone (MIN) lets you set your minimum target speed Zone (MAX) lets you set your maximum target speed Clock shows the current time and date (You may need to adjust the settings to display your local time.) Timer shows session time The timer starts automatically whenever you start moving and stops whenever you stop moving. Press and hold to shut down the S300 S300 NAVMAN S300 -- Modes Use the modes modes Speed operating details clear all session data* clear all session data* edit AVG Speed (AVG) MAX Speed (MAX) clear max speed only 2 873 Odometer clear odometer only accept ZONE SET Zone OFF Zone OFF Zone OFF Zone ON accept Zone ON edit accept edit Zone MIN Zone MIN accept edit Zone MAX Zone MAX Clock clear all session data* clear all session data* Timer (*Does not clear odometer.) * KEY = press this button = press this button = press both buttons together = press and hold both buttons together S300 QUICK START GUIDE NOW YOU KNOW. S300 Step 1 Get ready Fit the battery ! For best performance: General use = Alkaline Below 5 oC = NiMH 1. Turn D-ring anti-clockwise and slide enclosure cover down to open battery enclosure. 2. Insert battery with «» end as indicated inside enclosure. 3. Replace enclosure cover (ensuring lugs at the bottom of the cover are aligned with slots in the enclosure surround), turn D-ring clockwise to seal. Fit the S300 The S300 is designed to be worn on the left upper arm. You may wish to adjust some of the settings prior to fitting. L Be outdoors The S300 is not intended for operation indoors or under water as it uses Global Positioning System (GPS) satellites to get time and date information, and to calculate distance and speed. For best results, always use the S300 outdoors with an unobstructed view of the sky. S300 Step 2 Get set Know the buttons The control buttons, and (as shown above) are pressed separately or together to turn the unit «ON» and «OFF», cycle through modes, and select mode options. Know the startup options 1. enter setup 2. start normal operation ! Always enter setup first if you wish to change settings. To enter setup after starting normal operation, you must shut down and re-start the S300. Flashing icon = seeking GPS signals Constant icon = GPS signals obtained Startup could take up to 80 seconds to get all satellite data. Enter setup Press and hold to enter setup counter If you release before the counter reaches zero, the S300 will immediatly start normal operation. For details about system settings see over page or consult User Guide. Press and hold to leave setup counter After leaving setup, the S300 automatically starts normal operation displaying the speed mode first. S300 Step 3 Go Start normal operation Press to start normal operation When starting directly into normal operation S300 will start in the mode it was in at last shutdown. The S300 automatically operates whenever you are moving and pauses operation while you are stationary. Modes are accessed in the following order: AVG MAX Speed MAX Speed Timer Speed AVG Clock Odometer Zone OFF Zone ON Zone MIN 2 873 ZONE SET Zone MAX For details about modes or setting zone limits, see over page or consult User Guide. Mode example (speed) session distance km current speed km/h speed mode icon Mode icons appear in the lower section of the screen. While in Speed mode you can monitor session distance and current speed. You can also clear session data. While in Speed mode Press and hold to clear all* session data (*Does not clear odometer.) Press to go to next mode When you want to shut down the S300 Press and hold Now you know. S300 LA000535A © 2005 Navman NZ Ltd. All rights reserved. "Sport.Tool" and "Now you know" are trademarks of Navman NZ Ltd.