User manual TANDBERG 420LTO - QUICK START GUIDE

Tandberg 420LTO Half Height LTO2 Tape Drive Quick Installation Guide Revision 1 ­ February 2005 Mechanical Installation For mechanical mounting specifications, please refer to Figure 1. Allowed mounting position is either horizontal with the indicator LEDs to the right, or vertical with the LEDs up. The drive occupies a half-size 5.25-inch slot with standard holes for mounting screws on both sides of the drive chassis and at the bottom of the drive. Figure 1 Important! Mounting screw requirements Mounting specifications · · · · · Only M3 (metric) screws must be used for mounting the drive Maximum permitted screw penetration: 3.0 mm Minimum required screw penetration: 2.0 mm Screw torque, mounting screws: 0.5 Nm Screws are supplied with all the Tandberg 420LTO drive variants Do not use longer screws or higher screw torque than specified! Figure 2 Allowed mounting orientations 2 SCSI Identification Make sure that the drive unit has the proper SCSI-ID before it is connected to a computer system. Refer to manuals for host computer and application software to obtain the correct ID. For correct mounting of ID-jumpers at the rear of the drive, please refer to Figure 3 and Table 1. External drives have a thumb-wheel switch to set the SCSI-ID (see Figure 6). Power Connector Service Connector SCSI Connector Figure 3 The factory default drive number setting is SCSI ID = 2. If the drive has to be set up with a different unit number, the straps (on the Service Connector) have to be connected according to Table 1. Example: SCSI ID = 3 Drive connectors SCSI ID=0 SCSI ID=1 SCSI ID=2 SCSI ID=3 SCSI ID=4 SCSI ID=5 SCSI ID=6 SCSI ID=7 SCSI ID=8 SCSI ID=9 SCSI ID=10 SCSI ID=11 SCSI ID=12 SCSI ID=13 SCSI ID=14 SCSI ID=15 Table 1 Service Connector strap settings for SCSI ID (Dark = Strap mounted) 3 SCSI Cable Host SCSI-bus Internal Terminator Connector Last SCSI Device 10 cm Figure 4 SCSI cable (Ordering no. 43 32 63) (Ordering no. 43 20 53) (Ordering no. 43 20 52) (Ordering no. 43 32 64) · Internal SCSI-LVD/SE-cable with 5 connectors · Internal, removable SCSI-LVD/SE-terminator · External, removable SCSI-LVD/SE-terminator · External SCSI 68HD/VHDCI 320MBs Termination The SCSI-bus cable must be terminated in both ends according to SCSI specifications. If the tape drive is the last device on the bus, the bus must be terminated within 10 cm of the tape drive connection. Tandberg 420LTO has a combined SCSI-LVD/SE interface embedded. The PC-98 Specification specifies that the termination of the SCSI-bus system is a part of the SCSI-cable and not a part of the SCSI-device. As a result, termination cannot be turned on or off directly on the tape drive itself. For internal devices, a SCSI-cable with an integrated terminator or a separate terminator applied to the end connector of the cable, 10 cm from the last device, must be used. External devices must be terminated with an external terminator on the last device on the SCSI-bus. Software Installation For Software Application support and software drivers, please see www.tandberg.com/ > SUPPORT > LTO Support and www.tandberg.com/ > SUPPORT > Software Compatibility For installation of Backup Application software, refer to the software vendor's software application user guide supplied with the software or on the software vendor's web. 4 Front LED Indicators Figure 5 Light Emitting Diodes (LED) Drive State READY LED (Green left) ACTIVITY LED (Green) CLEAN LED (Amber) FAULT LED (Amber right) LED-test. The LEDs are turned ON one-by-one. Power-On Self-Test starts in parallel with the LED-test . Cartridge not loaded. Cartridge loaded, no activity Cartridge loaded, activity Cleaning Cartridge loading or unloading Unrecoverable drive failure Over temperature Media Error (wrong, write protected or harmed media) ON ON ON ON OFF ON ON OFF OFF ON / OFF OFF OFF OFF OFF Flashing Flashing Flashing OFF OFF Flashing ON / OFF ON / OFF ON / OFF ON ON / OFF ON / OFF ON / OFF ON / OFF OFF OFF OFF OFF OFF Flashing ON Flashing Table 2 Front LED behavior during normal operation For a complete description of LED behavior see Tandberg 420LTO Reference Manual. 5 Media and Capacities Drive Model Media Name Tape Length Capacity (Native) Tandberg 420LTO LTO Ultrium Generation 2 (Native format) LTO Ultrium Generation 1 (Read/Write compatible) 609 m 609 m 200 GByte 100 GByte Table 3 Media alternatives External Tabletop Enclosure ON/OFF Switch Cooling Fan SCSI_ID Switch Power Connector SCSI Interface Connectors Figure 6 External tabletop enclosure, rear side Power Requirements Tandberg 420LTO in external tabletop enclosure: AC Input: 100 VAC / 0.6 A or 240 VAC / 0.3 A, 50-60 Hz Tandberg 420LTO as standalone: DC Input (typical operation): 5 VDC / 2.1 A, 12 VDC / 0.6 A Heat Dissipation Tandberg 420LTO as standalone: Operating: Sleep mode with cartridge inserted: 18 W 9W 6 Total customer satisfaction is of the utmost importance to Tandberg Data. We guarantee that this product left our premises defect free. If you are not satisfied with the quality of this product, please contact your distributor or the nearest Tandberg Data office to have the problem solved! For more documentation and information, please see our website www.tandberg.com. 7 Tandberg Data International headquarters Tandberg Data ASA, Kjelsåsveien 161, Oslo, P.O. Box 134 Kjelsås, N-0411 Oslo, Norway. Tel: +47 22 18 90 90. Fax: +47 22 18 95 50. www.tandberg.com Worldwide subsidiaries Inostor Inc., 13000 Gregg Street, Poway, CA 92064, U.S.A. Tel: +1 858 726 0277. Fax: +1 858 726 0278. Tandberg Data GmbH, Feldstrasse 81, D-44141 Dortmund, Germany. Tel: +49 231 5436 0. Fax: +49 231 5436 111. Tandberg Data S.A.S., 16/18 Ave. Morane-Saulnier, F-78941 Vélizy Cedex, France. Tel: +33 1 39 26 01 01/00800-82632374. Fax: +33 1 34 65 02 89 (for technical support: 00800-07867243). Tandberg Data (Asia) Pte. Ltd, 20 Bendemeer Road, #04-05 Cyberhub, Singapore 339914, Tel: +65 6396 0786. Fax: +65 6396 0787. Tandberg Data (Japan) Inc., Eitaibashi Eco-Piazza Bldg. 8th floor 29-13, Shinkawa 1-chome, Chuo-ku Tokyo 104-033, Japan Tel: +81 3 5566 2871. Fax: +81 3 5566 2875. Tandberg Data (UK) Ltd., Registered Office, High Street Redbourne, Herts AL3 7LW, UK Tel: 00800-82632374. Fax: 00800-07867243. Specifications subject to change without notice. All trademarks are the property of their respective owners. ©2005 Tandberg Data ASA. All Rights reserved. Part No. 433261-01. February 2005.