User manual EPSON STYLUS CX3200 - QUICK START

Start Here EPSON Stylus CX3200 ® 5 Install Ink Cartridges 1 Lift up the scanner. continued 7 Press down the ink cartridge clamps until they snap shut. 1 Unpack 1 Make sure you have all the parts shown here. If any parts are missing, contact EPSON as described on the back of this sheet. continued 2 Slide the transportation lock back to the unlock position. 8 Carefully lower the scanner back down into place. The Stylus CX begins charging the ink delivery system. Charging takes about 1 1/2 minutes. The green light flashes and the Stylus CX makes various sounds. Don't turn it off while the green light is flashing or you'll waste ink. Stylus CX 3 Close the scanner lid. 2 Peel off the tape and remove the plastic piece from the ink cartridge holder. Caution: You must install both cartridges and leave them installed for all types of printing. To avoid damaging the Stylus CX, never move the print head by hand. Paper support USB cable Software CD-ROM Booklet 3 Attach the Parts 1 Insert the paper support into its three slots. 6 1 Ink cartridges Feeder guard Load Paper Flip the feeder guard forward. 2 Remove any tape and packing materials, as shown. 3 Press and hold the On button for 2 seconds. The green light flashes and the scanner carriage and print head move. Press the On button 2 Snap the feeder guard into its two slots in the sheet feeder. 2 Place a stack of paper against the right side of the feeder, beneath the tab. Pinch the left edge guide and slide it against the paper. Do not remove this sticker yet 4 Unwrap the ink cartridges and remove the yellow tape. Note: There may be additional packing materials or tape in locations different from the ones shown here. Do not remove the sticker covering the USB port yet. 5 Lift up the ink cartridge clamps. Open the output tray and pull out the extension Caution: Make sure you load paper behind the feeder guard. 2 Unlock 1 Open the scanner lid, as shown. Remove any packing materials under the lid. 4 Plug In 1 Plug the Stylus CX into a grounded electrical outlet. Do not connect the USB cable yet. 3 Flip the feeder guard back over the stack of paper. 6 Insert the ink cartridges with the labels face-up. 4 Position the Stylus CX so the front is at least 9 inches from the edge of the table. continue continue Turn over 7 Install Software For Macintosh® installation instructions, see the booklet that came with your ® Stylus CX. Follow the steps below to install software for Windows. continued 8 9 ® If you see a message about installing QuickTime, click Yes and follow the on-screen instructions. You don't need a registration number. Using the Control Panel s Any Questions? Here's where to look for answers: On-screen User's Guide Double-click the EPSON User's Guide icon on your desktop. TM TM On-screen Help for EPSON Smart Panel, ArcSoftTM PhotoImpression, TM Film Factory, and EPSON TWAIN TM EPSON Software 1 Make sure the Stylus CX is not connected to your computer, then turn on your computer. Note: If your Stylus CX is turned on and connected to your computer, you may see several New Hardware Wizard screens. Click Cancel for each of these screens and disconnect your Stylus CX. You can't install your software that way. When you see the final screen, make sure the Stylus CX is still on and paper is loaded. Click Print Test Page. s You can copy on EPSON Glossy Photo Paper or Premium Glossy Photo Paper in 4 x 6 or 5 x 7 sizes. Press the right Menu button to display Quality&Paper or Paper size. Then press the ­ Value button to select the settings you want. Press Stop after each setting. You can make borderless copies of photos. Press the right Menu button to display Copy mode. Then press the ­ Value button to select Border Free. Click the Help button or question mark that appears on the screen when you're using any of these programs. For Film Factory, you can also go to Start > Programs (or All Programs) > Film Factory > Getting Started Guide. EPSON Technical Support EPSON provides technical assistance 24 hours a day through the services described below: Click to print a test page Note: If the test page doesn't print, see the Solving Problems section. s 10 Click Cancel Click Register and follow the instructions on the screen to register your product. At the last screen, click Done. Click Exit, then remove the CD-ROM. Now you're ready to copy, scan, and print. See the next section or your on-screen EPSON User's Guide for instructions. You can make multiple wallet-size copies on one sheet of plain paper. Press the right Menu button to display Copy mode. Then press the ­ Value button to select Repeat. World Wide Web http://support.epson.com Automated Telephone Services To use these services, you must have a touch tone telephone and call (800) 922-8911. Your EPSON SoundAdviceSM Express Code is 70420. Use this code to quickly select your product in SoundAdvice. To Speak to a Technical Support Representative Dial (562) 276-4382 (U.S.) or (905) 709-3839 (Canada), 6 AM to 6 PM, Pacific Time, Monday through Friday. Toll or long distance charges may apply. Software Technical Support Software EPSON Smart Panel ArcSoft PhotoImpression Telephone (510) 445-8616 Fax (510) 445-8601 Internet and E-mail tech@newsoftinc.com 11 2 3 Insert your Stylus CX CD-ROM in your CD-ROM or DVD drive. The Software Installation screen opens automatically. Click Install. s How to Copy Click Install You can copy two pages onto one page. Press the right Menu button to display Copy mode. Then press the ­ Value button to select 2-up. Place the first page on the glass and press one of the Copy buttons. When you see the message, remove the first page and place the second page on the glass. Then press the Copy button again. 1 2 Open the scanner lid. Place your document or photo face-down on the glass, in the corner shown below. Move your document about 0.1 inch from the top and side edge so your entire document is scanned. Note: If the install screen doesn't open automatically, do the following: for Windows XP: click Start > My Computer. Then double-click the EPSON CD-ROM icon. For Windows 2000/Me/98: double-click My Computer. Then double-click the EPSON CD-ROM icon. (510) 440-9901 8:30 AM to 5:30 PM, PST Monday-Friday (510) 440-1270 www.arcsoft.com support@arcsoft.com s 4 5 When you see the license agreement, read it and click Agree. Then follow the instructions on the screen to install the drivers. When you see this screen telling you to connect your Stylus CX, make sure it is turned on, then remove the sticker from the USB port on the back. You can also use the Control Panel to run maintenance programs and see how much ink you have left. Press the right Menu button to display Head Alignment, Nozzle Check, Head Cleaning, Change Cartridge, or Ink Levels. For more information about using the control panel or printing and scanning from your computer, double-click the EPSON User's Guide icon on your desktop. How to Get Paper and Ink For the best prints and copies, use genuine EPSON ink and paper. You can buy them from your local store or from the EPSON StoreSM at (800) 873-7766 or www.epsonstore.com (U.S. sales only). Look for these cartridges and paper: 3 4 Close the scanner lid. Use the Control Panel to select settings: Solving Problems Make more than one copy Stop Select settings If the red Error light is on, check the message on the control panel. If your problem is listed here, try these suggestions. For more information, see your software Help or your on-screen EPSON User's Guide. The Found New Hardware Wizard appears on your screen. Click Cancel and follow the steps in section 7. Disconnect the Stylus CX before installing the software. T040120 Black Ink Cartridge T041020 Color Ink Cartridge 6 Connect the square end of the USB cable to your Stylus CX USB port, then connect the flat end of the cable to any available USB port on your computer. On Scan Save(3sec) Error Recall Reset all(3sec) Return to Top Reset Copies Value B&W Menu py Co Color Enter Cancel settings Select menus Black and white copy Return to menu or cancel job Color copy Photo Quality Ink Jet Paper Bright white paper perfect for newsletters, proposals, and presentations. You see an error message when you try to print or scan. Make sure your Stylus CX is connected to your computer, plugged into a power source, and turned on. Glossy Photo Paper Heavier weight paper for enlargements and borderless 4 x 6 prints. · To make the copy lighter or darker, press the right Menu button until you see Lighter/Darker on the control panel screen. Then press the + or ­ Value button to choose from the 5 settings. Press Stop. After you connect your Stylus CX, Windows displays several messages as it detects your device. · To enlarge or reduce a photo, press the right Menu button until you see Zoom In/Out on the control panel screen. Then press the + or ­ Value button to display the proportion you want. Press Stop. The Stylus CX doesn't work. Slide back the transportation lock under the lid to unlock the scanner. See section 2. Make sure you're using the USB cable that came with your Stylus CX. Make sure your EPSON Stylus CX3200 software is installed correctly. Make sure you insert paper behind the feeder guard, not in front of it. Premium Glossy Photo Paper Highest quality paper for borderless prints in frame-ready sizes. 7 Continue following the instructions on the screen to install the rest of your software. 5 It will take several minutes to install the remaining software. Don't cancel the installation. Press the Color Copy button (for color copies) or B&W Copy button (for black and white copies). Your document or photo is scanned and printed. continue EPSON and EPSON Stylus are registered trademarks and EPSON Smart Panel is a trademark of SEIKO EPSON CORPORATION. EPSON Store and Sound Advice are service marks, and EPSON Software is a trademark, of Epson America, Inc. General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks. Copyright © 2002 by Epson America, Inc. Printed on recycled paper. 8/02 Printed in USA CPD-14881