User manual PLANAR PR5020 - QUICK START

The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be reproduced, translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission. Windows is a registered trademark of Microsoft, Inc. Other brand or product names are trademarks of their respective holders. Important Recycle Instructions: Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG. Register Your Planar Products Today Thank you for choosing Planar. To assure you receive all the benefits of your Planar product and services, register your Planar product today. Visit our website to register your product at http://www.planar.com/support/product_registration.html Cables, Replacement Lamps and Accessories To find cables, replacement lamps and accessories for your Planar projector, LCD monitor, touchscreen or other Planar products visit our online store at www.PlanarOnline.com or find other stores who carry Planar products at http://www.planar.com/howtobuy 1 3 1 2 5 7 14 1 2 3 4 5 6 4 5 6 13 12 11 10 9 87 8 9 10 2 1 2 3 6 C B A Main Language Remote control test USB test Button test Color test Sound test Setup Config English Utility Tool Status D 837 65 4 Menu= Exit Item Adjust Scroll 3 1 26 25 24 23 22 21 20 19 18 17 16 2 3 4 5 6 7 8 9 10 11 12 13 7 A B C D 8 A C D 15 14 4 2 1 3 B B B 1 2 Remote Buttons Description CHECK PARTS LIST 2. 3. 4. 5. 6. 7. 8. 9. Press to operate the on-screen pointer Up arrow when connected through USB to a PC Right arrow when connected through USB to a PC Down arrow when connected through USB to a PC Page down when connected through USB to a PC Navigate and change settings in the OSD Congratulations on your purchase! Please check that the following items are included with your projector. Parts List 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Projector Remote control with batteries Power cord Computer cable (VGA-VGA) USB cable Composite cable (RCAx3-RCAx3) Audio cable (Mini jack-Mini jack) CD-ROM (user manual) User's Guide Carrying case 10. Adjust volume 11. Mutes the built-in speaker 12. Zoom in 13. Zoom out 14. Freeze/unfreeze the on-screen picture Contact your dealer immediately if any items are missing or damaged. 2 1. 2. 3. 4. 5. 6. 7. 8. IDENTIFY PROJECTOR PARTS Projector Parts Description Focus--turn to focus the projected image Zoom--turn to enlarge the projected image Lamp cover screws OSD buttons and LEDs Front IR receiver Lens Lens cover Height adjusters--adjusts level of projector 15. Make the screen blank 16. Detect the input device 17. Auto adjustment for phase, tracking, size, position 18. Open the OSD 19. Open the OSD Status menu (menu only opens when input device detected) top/bottom) effect the OSD 20. Correct image-trapezoid (wider 21. Navigate and change settings in 22. Change settings in the OSD 23. Page up when connected through USB to a PC through USB to a PC through USB to a PC Caution: Overheating can damage the projector. Do not block any of the air vents around the unit. 3 2 IDENTIFY REMOTE CONTROL PARTS Remote Buttons Description 24. Left arrow when connected 25. Enter key when connected 1. Lights when the remote control is used -- User's Guide -- Remote Buttons Description 26. Turn the projector on or off 5 2 MAKE CONNECTIONS 4 1. INSERT REMOTE CONTROL BATTERIES Remove the battery compartment cover by sliding the cover in the direction of the arrow. Insert the supplied batteries taking note of the polarity (+/-). Replace the cover. Warning: As a safety precaution, disconnect all power to the projector and connecting devices before making connections. Label Description Receiver for IR signal from remote control Connect the DVID cable from a computer (not supplied) Connect a VGA cable from a computer (supplied) Connect to a monitor (not supplied) Connect S-video cable from a video device (not supplied) Connect a composite video cable from a video device (supplied) Connect the audio cable from an audio input device (supplied) Connect the audio cable from an audio input device (supplied) Connect an audio cable from the computer's audioout connector (supplied) 2. 3. 1. Rear IR receiver DVI-D (For PR5020 only) VGA IN 2. 3. 4. VGA OUT 5. S-video 6. Video 7. Audio in-R 8. Audio in-L 9. Audio-in -- User's Guide -- Label Description Audio loop-thru Connect the USB cable from a computer (supplied) Installation control 10. 11. Audio-out USB 4. 5. 6. 7. Press the Menu button and then press the cursor button until Tool is highlighted [D]. Press the cursor button until Language is highlighted [D]. Press the until your language is displayed. Press the Menu button twice to close the OSD. RS-232 12. (For PR5020 only) 13. Power Connect the power cord (supplied) Secure to permanent object with a Kensington® Lock system 14. Lock Security 7 1. ADJUST PROJECTOR LEVEL To raise the level of the projector, lift the projector [A] and press the height-adjuster button [B]. The height adjuster drops down [C]. 6 1. POWER ON/OFF AND SET LANGUAGE Connect the power cord to the projector [A] .Connect the other end to a wall outlet. Switch [B] from on (O) to off ( ) The POWER and READY LEDs on the projector turn on. Turn on the connected devices. Ensure the Power LED is on (not flashing) and then press the Power button [C] to turn on the projector. (If any LEDs are flashing, do not press the Power button. See "LED Error Messages" in the CD-ROM user manual.) The projector splash screen displays and connected devices are detected. 2. To lower the level of the projector, press the heightadjuster button and push down on the top of the projector. To adjust the angle of the picture [D], turn the tilt adjuster right or left until desired angle has been achieved. 2. 3. 3. 8 2 1. 2. ADJUST IMAGE AND VOLUME Use the Image-focus control to sharpen the projected image (A). Use the Image-zoom control to resize the projected image and screen size (B). -- User's Guide -- 3. 4. Use the Keystone buttons to correct keystone (wider top or bottom) effect (C). Use the Volume buttons to adjust the volume (D). NEED MORE INFORMATION? The CD-ROM that shipped with your projector features a detailed user manual in a printer-friendly format. The user manual includes hardware, operation, and maintenance descriptions. You will also find troubleshooting procedures and instructions on securing the projector by means of a security lock. The projector has an On-Screen Display (OSD) that lets you make image adjustments and change various settings. To open the OSD, press the Menu button on the remote control. Use the remote control cursor buttons to navigate and make changes to the projector settings. Refer to the "On-Screen Display Settings" section of the CD-ROM user manual for more information. -- User's Guide --