User manual LEXMARK E120 - Quick Reference

Quick Reference Understanding the Operator Panel The printer operator panel has two buttons and two lights. Lights indicate the status of the printer. Buttons are used to continue or cancel the current print job. When the printer is turned on, both lights cycle as a self test is performed. Also, when the printer is reset, or when a printer setting is changed in the menus, both lights cycle. Continue Ready / Data Cancel Error · · · · · Press and release Continue Press and release Continue Press Continue to resume printing. twice quickly to display the secondary light sequence. from the Ready state to print the menu settings page. to cancel the current job. until both lights come on to reset the printer. Press and hold Cancel Press and hold Cancel Understanding the operator panel lights The operator panel lights mean different things, depending on their sequence. Lights that are off, on, and/or blinking indicate printer conditions such as printer status, intervention, or service. Use the light sequence table to find the message being indicated, then click the message for more information. Quick Reference 1 Light sequence Ready / Data light on = Ready / Data light blinking = Error light on = Error light blinking = Primary light sequence Ready / Data Secondary light sequence Ready / Data Error Error Message Ready / Power Saver Busy Waiting Cancel job / Reset printer Flushing buffer Invalid engine code (Ready / Data light blinks once) Not ready (Ready / Data light blinks once) Printing font list or menu settings page Programming engine code or system code Restoring factory defaults Cartridge region mismatch (Ready / Data light blinks four times) Change cartridge / Defective cartridge (Ready / Data light blinks three times) Open door (Ready / Data light blinks once) Complex page (Ready / Data light blinks three times) ENA connection lost (Ready / Data light blinks five times) Insufficient collation area (Ready / Data light blinks three times) Load media (Ready / Data light blinks once) Print side two of a duplex job (Ready / Data light blinks once) Understanding the Operator Panel 2 Primary light sequence Ready / Data Secondary light sequence Ready / Data Error Error Message Memory full (Ready / Data light blinks three times) Host interface disabled (Ready / Data light blinks five times) Jam in the printer paper path (Ready / Data light blinks ten times) Jam in Tray 1 / priority feeder (Ready / Data light blinks four times) Short paper (Ready / Data light blinks three times) Toner low (Ready / Data light blinks eight times) Replace long-life photoconductor kit (Ready / Data light blinks once) Service error (Ready / Data light blinks ten times) Printing the menu settings and network setup page To print the menu settings and network setup pages, press from the Ready state. The printer automatically prints the menu settings and network setup pages. A list of the printer settings and the current default values are printed on the menu settings page. The current default settings are marked with an asterisk. The network setup page confirms the network Status is "Connected" and lists the current network settings. Restoring factory defaults This function will return most of the settings back to their factory values. The display language and the settings in the Network and USB menus are not returned to the factory defaults. To restore the printer to the original factory defaults, press and hold seconds. for more than three Note: Before restoring the factory defaults, make sure the host computer or network has stopped sending information to the printer. Printing the menu settings and network setup page 3 Loading paper or other print media Source Tray 1 Sizes A4, A5, JIS-B5, letter, legal, executive, folio, statement, universal Types Plain paper, bond paper, transparency, label Card stock Envelope Plain paper, bond paper, transparency, label Plain paper, bond paper Card stock Envelopes Capacity* (sheets) 150 sheets 5 transparencies 5 labels 5 cards 5 envelopes 15 sheets 5 transparencies 5 labels 30 sheets 5 cards 3 envelopes 3 x 5 inch, other 7¾, 9, 10, DL, C5, B5, other Priority feeder A4, A5, JIS-B5, letter, legal, executive, folio, statement, universal A6 3 x 5 inch, other 7¾, 9, 10, DL, C5, B5, other * Capacity for 20 lb print media, unless otherwise noted. Universal size ranges: ­ Tray 1: 76­216 x 190­356 mm (3.0­8.5 x 7.5­14.0 in.) (includes 3 x 5 in. cards) ­ Priority feeder: 76­216 x 190­356 mm (3.0­8.5 x 7.5­14.0 in.) (includes 3 x 5 in. cards) To help prevent jams: · Prepare print media for loading by flexing or fanning it back and forth. Straighten the edges on a level surface. · · Do not overload the paper trays. Never mix media types within a tray. Loading paper or other print media 4 Loading Tray 1 1 Open the paper cover by lifting up until the cover clicks into a fully open position. 2 Adjust the slide and attached backstop to the length of the selected print media. Note: To decrease width, push in on the left guide. To increase width, squeeze the tab attached to the right guide, and slide it to the right. Loading paper or other print media 5 3 Place the prepared print media into the tray, and lightly adjust all guides against the loaded print media edges. Note: Load letterhead paper with the design side facing up and the top edge of the sheet feeding into the printer first. Load envelopes with the flap side down and the return address first. The stamp area will feed through last. 4 Close the paper cover. Loading paper or other print media 6 Loading print media into the priority feeder The priority feeder can be used to make quick runs of print media types or sizes not currently loaded in Tray 1. 1 Adjust the guides to the width of the print media. 2 Place the selected print media, with the side to be printed faceup, at the center of the priority feeder. The print media rests on the Tray 1 paper cover. 3 Push the selected print media into the printer until the print media stops. Note: Do not force print media into the feeder. Forcing print media causes jams. Canceling a print job A print job can be canceled from the operator panel or from the computer. The Cancel job light sequence appears on the operator panel when a job is canceled (see "Cancel Job/Reset printer" on page 30 of your User's Guide). From printer operator panel Press and release to cancel the current print job. Press and hold seconds to reset the printer. for more than three Canceling a print job 7 From a Windows computer 1 Click Start Settings Printers. 2 Double-click the printer being used to print the current job. A list of print jobs appears. 3 Right-click the current document, and then click Cancel. From a Macintosh computer When a job is sent to print, the printer icon appears on the desktop. 1 Click Applications. 2 Click Utilities. 3 Double-click Printer Setup Utility. A list of print jobs appears. 4 Double-click the printer name to see a list of print jobs. 5 Click the print job you wish to cancel. 6 From the tool bar, click Delete. Canceling a print job 8 Clearing jams When a jam occurs, the printer stops, and the Error light on the operator panel blinks. To determine the location of the jam, view the secondary light sequences. Prepare the printer for jam removal by opening the paper support and removing all printed pages from the output bin. Then, follow these steps to clear the entire paper path. 1 Open the rear door by sliding the door release button to the right. 2 Remove any lodged print media from the paper path. Warning: When the rear door is open, be careful not to touch the attached roller. Touching the roller can cause contamination and affect print quality. Do not leave the rear door open for an extended amount of time. Exposure to light will damage the blue drum of the long-life photoconductor kit and affect print quality. Clearing jams 9 3 Open the top door, and remove any lodged print media from the paper path. CAUTION: The fuser may be hot. To avoid personal injury, use caution when opening the top door to remove a jam from the fuser area. 4 Open the front door by sliding the release button to the left. Clearing jams 10 5 Pull the front door up until it clicks into an open position, and remove any lodged print media. Note: It may be necessary to remove the toner cartridge and place it on a flat, clean surface to reach print media lodged behind it. Replace the toner cartridge when the print media has been located and removed. 6 Close the front door by pressing firmly in the center of the front door with your thumb until the door clicks shut. If you need more information · · Refer to the Software and Documentation CD that came with your printer for helpful information about using and maintaining your printer. Contact your administrator or Help desk if you have questions about network printing. If you need more information 11