User manual LEXMARK T522 - Quick Reference

Quick Reference Lexmark Laser Printer Operator panel Ready 1 Loading a paper tray Pull here Length guide Loading the multipurpose feeder 1 Push the lower release latch. 2 Pull the metal bar out far enough to support your paper size. 3 Slide the paper width guide to the far right. Loading letterhead Letterhead must be loaded differently depending on whether you want your print job to be single-sided or double-sided (duplexed). In the multipurpose feeder In a paper tray Length guide lever 2 Paper and transparencies Width guide Envelopes Single-sided printing Menu Select 3 Return 4 Paper size indicators Go 5 Stop 6 Press Menu to: · · · · Enter the menus from the ready state Scroll through menus or values Increase or decrease a numerical value Display the Job Menu while the printer is busy Complete these instructions to load print materials into any of the standard or optional trays. All paper trays are loaded the same way. 1 Remove the paper tray. 2 Pull the width guide tab and slide the width guide to the far right side of the tray. 3 Squeeze the length guide lever and slide the length guide to the correct position for the size paper you are loading. 4 Place the paper into the paper tray with the recommended print side face down for single-sided printing and face up for double-sided printing. Do not fill paper above the paper capacity mark (fill line). Pull the width guide tab and slide the width guide to the left until it lightly rests against the edge of the paper stack. Sizes: Letter Legal Executive A4 A5 B4 JIS-B5 Folio* Statement* 9 Envelope DL Envelope B5 Envelope C5 Envelope 7 3/4 Envelope 10 Envelope Other Envelope Double-sided (duplex) printing Supported print material sizes and types Types: Plain Paper Card Stock Transparency Labels Bond Letterhead Preprinted Colored Paper Custom Type Envelope Press Select to: · Select the item on the second line of the display · Save the selection as a new default setting Press Return to: · Return to the previous menu level Press Go to: · Exit printer menus and return to the Ready state · Clear messages Press Stop to: · Temporarily stop all print activity without losing data *This size is not available until Size Sensing is turned off. For more information, refer to the online information. Copyright © 2001 Lexmark International, Inc. All rights reserved. Printed in USA This document is printed on recycled paper. 5/01 E.C. 2H0003 P/N 09H0412 Operator panel menus Paper Menu Paper Source Paper Size Paper Type Custom Types Universal Setup Substitute Size Configure MP Envelope Enhance Paper Texture Paper Weight Paper Loading Finishing Menu Duplex Duplex Bind Copies Blank Pages Collation Separator Sheets Separator Source Multipage Print Multipage Order Multipage View Multipage Border Utilities Menu Print Menus Print Net Setup Print Fonts Print Directory Factory Defaults Format Flash Defragment Flash Format Disk Job Acct Stat Hex Trace Job Menu Confidential Job Held Jobs Cancel Job Reset Printer Print Buffer Quality Menu Print Resolution Toner Darkness PQET PictureGrade Accessing paper jam areas You open doors and covers, remove paper trays, and remove options to access paper jam areas. If your printer has a multipurpose feeder, it is visible when the lower front door is opened. The illustration shows the location of paper sources and possible paper jam areas. Print quality problems Problem Print is too light. Action · The toner may be low. To utilize the remaining toner, remove the cartridge by gripping the handles with both hands. With the cartridge arrows pointing downward, shake the print cartridge back and forth. Reinstall the cartridge and then press Go. · Change the Toner Darkness setting in the Quality Menu. · If you are printing on an uneven print surface, change the Paper Weight and Paper Texture settings in the Paper Menu. Verify that the correct print material is being used. 260 Paper Jam Envelope feeder 202 Paper Jam Printer rear door 200 Paper Jam 201 Paper Jam Upper front door 230 Paper Jam Duplex rear door Toner fog or background shading appears on the page. · Check the print cartridge to make sure it is installed correctly. · Change the print cartridge. · If the problem continues, change the charge roll. Serial Menu PCL SmartSwitch PS SmartSwitch NPA Mode Serial Buffer Job Buffering RS-232/RS-422 RS-422 Polarity Serial Protocol Robust XON Baud Data Bits Parity Honor DSR Parallel Menu PCL SmartSwitch PS SmartSwitch NPA Mode Parallel Buffer Job Buffering Advanced Status Protocol Honor Init Parallel Mode 1 Parallel Mode 2 PostScript Menu Print PS Error Font Priority PCL Emul Menu Font Source Font Name Point Size Pitch Symbol Set Orientation Lines per Page A4 Width Tray Renumber Auto CR after LF Auto LF after CR Setup Menu Printer Language Power Saver Resource Save Download Target Print Timeout Wait Timeout Auto Continue Jam Recovery Page Protect Display Language Alarm Control Toner Alarm Job Accounting 250 Paper Jam Lower front door (down when envelope feeder is installed) 230 Paper Jam Duplex front access cover 24x Paper Jam Integrated input tray 24x Paper Jam Paper trays Streaks appear on the page. · The toner may be low. To utilize the remaining toner, remove the cartridge by gripping the handles with both hands, and then shake the print cartridge vigorously. Reinstall the same print cartridge. · If you are using preprinted forms, make sure the ink can withstand temperatures of 212°C (414°F). Warning: Do not attempt to clear any paper jam using tools or instruments. This may permanently damage the printer. The job prints, but the top and side margins are incorrect. · Make sure the Paper Size setting in the Paper Menu is correct. · Make sure the margins are set correctly in your software application. Network Menu PCL SmartSwitch PS SmartSwitch NPA Mode Network Buffer Job Buffering Network Setup Mac Binary PS Infrared Menu Infrared Port PCL SmartSwitch PS SmartSwitch NPA Mode Infrared Buffer Job Buffering Window Size Transmit Delay Max Baud Rate USB Menu PCL SmartSwitch PS SmartSwitch NPA Mode USB Buffer Job Buffering Mac Binary PS LocalTalk Menu LocalTalk Port PCL SmartSwitch PS SmartSwitch NPA Mode LocalTalk Buffer Job Buffering NPA Hosts LocalTalk Name LocalTalk Addr LocalTalk Zone