DCP-8060 DCP-8065DN Before you can use the machine, you must set up the hardware and install the software. Please read this "Quick Setup Guide" for the correct setup procedure and installation instructions. Step 1 Setting Up the machine Quick Setup Guide Step 2 Installing the Drivers & Software Installing the Drivers & Software Windows NT® 4.0 Parallel Setup is Complete! Keep this "Quick Setup Guide", User's Guide and supplied CD-ROM in a convenient place for quick and easy reference at all times. Macintosh® Macintosh® Network Administrators Network USB Windows® Network Windows® Parallel Windows® USB Setting Up the machine Warning Warnings tell you what to do to prevent possible personal injury. Caution Cautions specify procedures you must follow or avoid to prevent possible damage to the machine or other objects. Improper Setup Improper Setup icons alert you to devices and operations that are not compatible with the machine. Note Notes tell you how you should respond to a situation that may arise or give tips about how the current operation works with other features. User's Guide Indicates reference to the User's Guide. Getting Started Carton Components 1 2 3 4 5 6 CD-ROMs For Windows® For Macintosh® 8 7 Quick Setup Guide AC Power Cord 1. Automatic Document Feeder (ADF) 2. Control Panel 3. Face-down Output Tray Support Flap (Support Flap) 5. Paper Tray 6. Power Switch 7. Document Cover 8. ADF Document Output Support Flap Drum Unit Assembly (including Toner Cartridge) 4. Front Cover Carton components may differ from one country to another. Save all packing materials and the carton. Austraria & New Zealand users: Hong Kong, Malaysia & Singapore users: The mains plug supplied with this machine is a grounded three pin plug. Make sure that the AC socket will accept this grounded three pin plug. This machine must be grounded, If in doubt, call a qualified electrician. Philipine & Thailand users: The mains plug supplied with this machine is a side grounded two pin plug. Make sure that the AC socket will accept this side grounded two pin plug. This machine must be grounded, If in doubt, call a qualified electrician. To ensure safe operation the supplied plug must be inserted only into a standard power outlet that is properly grounded through the standard electrical wiring. None grounded equipment may cause an electrical shock hazard, and may cause excessive electrical noise radiation. The interface cable is not a standard accessory. Please purchase the appropriate interface cable for the interface you intend to use (Parallel, USB or Network). Do NOT connect the interface cable at this time. Connecting the interface cable is done during the software installation process. USB interface cable Please make sure you use a USB 2.0 interface cable that is no longer than 2.0 meters. When you use a USB cable, make sure you connect it to the USB port of your computer and not to a USB port on a keyboard or non-powered USB hub. Parallel interface cable Please make sure you use a Parallel interface cable that is no longer than 2.0 meters. Use a shielded interface cable that is IEEE 1284-compliant. Network cable (DCP-8065DN only) Use a straight-through Category5 (or greater) twisted-pair cable for 10BASE-T or 100Base-TX Fast Ethernet Network. 1 Control Panel DCP-8060 1 2 3 4 5 9 8 7 6 DCP-8065DN 1 2 3 4 5 9 8 7 6 1 4 7 Status LED Dial Pad Copy keys 2 5 8 LCD (Liquid Crystal Display) Stop/Exit key Scan key 3 6 9 Menu keys Start key Print keys For the details of the control panel, see "Control panel overview" in Chapter 1 of the User's Guide. 2 Table of Contents Step 1 1. 2. 3. 4. 5. Setting Up the machine Install the Drum Unit and Toner Cartridge Assembly .................................... 4 Load Paper in the Paper Tray .......................................................................... 5 Release the Scanner Lock ................................................................................ 6 Connect the Power Cord .................................................................................. 6 Setting the LCD Contrast ................................................................................. 7 Step 2 Installing the Drivers & Software Supplied CD-ROM "MFL-Pro Suite" ................................................................................ 8 For USB Interface Cable Users (For Windows® 98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition) .... 10 For Parallel Interface Cable Users (For Windows® 98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition) .... 12 For Windows NT® Workstation Version 4.0 Users ......................................................15 For Network Interface Cable Users (DCP-8065DN only) (For Windows® 98/98SE/Me/NT/2000 Professional/XP/XP Professional x64 Edition) ...17 For USB Interface Cable Users ......................................................................................20 For Mac OS® 9.1 to 9.2 ......................................................................................20 For Mac OS® X 10.2.4 or greater ....................................................................... 22 For Network Interface Cable Users (DCP-8065DN only) ............................................. 25 For Mac OS® 9.1 to 9.2 ......................................................................................25 For Mac OS® X 10.2.4 or greater ....................................................................... 27 For Network Users and Administrators (DCP-8065DN only) BRAdmin Professional configuration utility (For Windows® users) .......................... 30 BRAdmin Light configuration utility (For Mac OS® X users) ...................................... 32 Options and Consumables Options ............................................................................................................................33 Replacement Consumables ...........................................................................................33 3 Step 1 Setting Up the machine 2 Unpack the drum unit and toner cartridge assembly. 1 Install the Drum Unit and Toner Cartridge Assembly Do not connect the interface cable. Connecting the interface cable is done during the software installation process. 3 1 Open the front cover by pressing the front cover release button (1). Gently rock it from side to side several times to distribute the toner evenly inside the cartridge. (1) 4 Put the drum unit and toner cartridge into the machine so that it clicks into place. 5 Close the front cover of the machine. 4 2 Load Paper in the Paper Tray 1 Pull the paper tray completely out of the machine. 4 Put paper in the paper tray. Check that the paper is flat in the tray and below the maximum paper mark (1). (1) Windows® Parallel 2 While pressing the blue paper guide release lever (1), slide the adjusters to fit the paper size. Check that the guides are firmly in the slots. 5 (1) Put the paper tray firmly back into the machine and unfold the support flap (1) before you use the machine. (1) 3 5 Network Administrators Macintosh® Network Fan the stack of paper well to avoid paper jams and misfeeds. For details on supported paper specifications, see "Acceptable paper and other media" in Chapter 2 of the User's Guide. Macintosh® USB Windows® Network Windows NT® 4.0 Parallel Windows® USB Setting Up the machine Step 1 3 1 Setting Up the machine Release the Scanner Lock 4 Connect the Power Cord Do not connect the Parallel or USB cable yet. Push the lever (1) in the direction shown to unlock the scanner. (The gray scanner lock lever is located at the back left side, under the document cover (2).) (2) 1 Make sure that the power switch is off. Connect the AC power cord to the machine. (1) 2 Plug the AC power cord into an AC outlet. Turn the power switch on. If Scanner Locked appears on the LCD, immediately release the scanner lock and press Stop/Exit. (See "Release the Scanner Lock" on page 6.) 6 5 Setting the LCD Contrast You can change the contrast to help the LCD look lighter or darker. Setting Up the machine Press to increase the contrast. --OR-- Press to decrease the contrast. Press OK. Go to the next page to install the drivers & software 7 Network Administrators Macintosh® Network Macintosh® USB Windows® Network Windows NT® 4.0 Parallel Windows® Parallel Windows® USB 1 2 3 4 Press Menu. Press 1. Press 6. Step 2 Installing the Drivers & Software Supplied CD-ROM "MFL-Pro Suite" The CD-ROM includes the following items: Install MFL-Pro Suite You can install the MFL-Pro Suite and multifunction drivers. Install Optional Applications You can install additional MFL-Pro Suite software utilities. Documentation View the User's Guide and other documents in PDF format (Viewer included). The User's Guide on the CD-ROM includes the Software and Network User's Guide for features available when connected to a computer (e.g. printing, scanning and networking details). . On-Line Registration You will be pointed to the Brother Product Registration Web page for quick registration of your machine. Brother Solutions Center Brother contact information and web site links offering the latest news and support information. Repair MFL-Pro Suite (For USB and Parallel cable users only) If you experience errors while installing the MFL-Pro Suite, you can use this function to automatically repair and re-install the software. MFL-Pro Suite includes Printer Driver, Scanner Driver, Brother ControlCenter2, ScanSoft® PaperPort® SE with OCR and True Type® fonts. PaperPort ® SE is a document management application for viewing scanned documents. Start Here OS 9.1-9.2 You can install the printer driver, scanner driver and Presto!® PageManager® for Mac OS® 9.1 - 9.2. Start Here OSX You can install the MFL-Pro Suite that includes the printer driver, scanner driver and the Brother ControlCenter2 for Mac OS® 10.2.4 or greater. You can also install Presto!® PageManager® to add OCR capability to the Brother ControlCenter2 and easily scan, share and organize photos and documents. Readme.html You can get important information and troubleshooting tips. Documentation View the User's Guide and other document in PDF format (Viewer included). The User's Guide on the CD-ROM includes the Software and Network User's Guide for features available when connected to a computer (e.g. printing, scanning and networking details). Brother Solutions Center You can access the Brother Solutions Center, a Web site offering information about your Brother product including FAQs, User's Guides, Driver updates and Tips for using your machine. On-Line Registration You will be pointed to the Brother Product Registration Web Page for quick registration of your machine. 8 Step 2 Installing the Drivers & Software Setting Up the machine Follow the instructions on this page for your operating system and interface cable. For the latest drivers and to find the best solution for your problem or question, access the Brother Solutions Center directly from the driver or go to http://solutions.brother.com For Network Users and Administrators...................... Go to page 30 9 Network Administrators Macintosh® Network Network Interface Cable Users (DCP-8065DN only) For Mac OS® 9.1 to 9.2 ............................................. Go to page 25 For Mac OS® X 10.2.4 or greater ............................. Go to page 27 Macintosh® USB USB Interface Cable Users For Mac OS® 9.1 to 9.2 ............................................. Go to page 20 For Mac OS® X 10.2.4 or greater ............................. Go to page 22 Windows® Network Network Interface Cable Users.................................... Go to page 17 (DCP-8065DN only) Windows NT® 4.0 Parallel Windows NT® Workstation Version 4.0 Users........... Go to page 15 (For Parallel Interface Cable Users) Windows® Parallel Parallel Interface Cable Users ..................................... Go to page 12 (For Windows® 98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition) Windows® USB USB Interface Cable Users .......................................... Go to page 10 (For Windows® 98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition) Step 2 Installing the Drivers & Software For USB Interface Cable Users (For Windows® 98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition) Make sure that you have finished the instructions from Step 1 "Setting Up the machine" on pages 4 - 7. Please close any applications running before installing the MFL-Pro Suite. 5 After reading and accepting the ScanSoft® PaperPort® SE License Agreement, click Yes. 1 Switch off the machine and disconnect the machine from the power socket (and from your computer, if you have already connected an interface cable). The installation of PaperPort® SE will automatically start and is followed by the ...