DCP-8040 DCP-8045D Before you can use the DCP, you must set up the hardware and install the driver. To help you get started in setting up the machine and installing the driver and software, please read this "Setup Guide" and follow the simple instructions. Step 1 Setting Up the Machine Quick Setup Guide Step 2 Installing the Driver & Software Installing the Driver & Software Version B Windows NT® 4.0 Parallel Setup is Complete! For the latest drivers and to find the best solution for your problem or question, access the Brother Solutions Center directly from the driver or go to http://solutions.brother.com Keep this "Quick Setup Guide", User's Guide and supplied CD-ROM in a convenient place for quick and easy reference at all times. Macintosh® Macintosh® For Administrators Network USB Windows® Network Windows® Parallel Windows® USB Setting Up the Machine Getting Started Carton Components DCP 8 1 2 3 5 4 CD-ROMs For Windows® For Macintosh® 6 7 Quick Setup Guide 1. Control Panel 2. Face-down Output Tray Support Flap with Extension (Support Flap) 3. (For DCP-8040) Manual Feed Tray (For DCP-8045D) Multi-purpose Tray (MP Tray) 4. Paper Tray 5. Front Cover 6. Power Switch 7. Document Cover 8. Automatic Document Feeder (ADF) User's Guide ADF Support Drum Unit Assembly (including Toner Cartridge) AC Power Cord Carton components may differ from one country to another. Save all packing materials and the carton. The interface cable is not a standard accessory. Please purchase the appropriate interface cable for the interface you intend to use (Parallel or USB). For Parallel use a bi-directional shield interface cable that is IEEE 1284-compliant, and not longer than 2 meters. For USB use a Hi-Speed USB 2.0 interface cable that is not longer than 2 meters. Please make sure that you use a Hi-Speed USB 2.0 certified cable if your computer uses a Hi-Speed USB 2.0 interface. Even if your computer has a USB 1.1 interface, you can connect the DCP. Warning When you move the DCP, grasp the side handholds that are under the scanner. Do NOT carry the DCP by holding it at the bottom. Control Panel DCP-8040 and DCP-8045D have similar control panel keys. 1 2 3 4 5 6 7 9 8 1. Print keys 4. Navigation keys 7. Stop/Exit 8. Start 9. Scan key 2. Status LED (Light-Emitting Diode) 5. Copy keys (Temporary Settings) 3. 5-Line Liquid Crystal Display (LCD) 6. Numeric keys For the details of the control panel, see "Control panel overview" in Chapter 1 of the User's Guide. Warning Indicates warnings that must be observed to prevent possible personal injury. Indicates cautions that must be observed to use the DCP properly or to prevent damage to the DCP. Hint Indicates notes and useful tips to remember when using the DCP. User's Guide Indicates reference to the User's Guide. Table of Contents Step 1 1. 2. 3. 4. 5. 6. 7. Setting Up the Machine Install the Automatic Document Feed (ADF) Support .................................... 2 Install the Drum Unit Assembly ........................................................................ 2 Load Paper in the Paper Tray ........................................................................... 3 Release the Scanner Lock................................................................................. 4 Install the Power Cord ....................................................................................... 4 Selecting Your Country (Not Language).......................................................... 5 Selecting Your Language .................................................................................. 5 Step 2 Installing the Driver & Software Supplied CD-ROM "MFL-Pro Suite"..................................................................... 6 For USB Interface Cable Users (For Windows® 98/98SE/Me/2000 Professional/XP).................................. 8 For Windows® 98/98SE/Me Users Only ............................................................ 10 For Windows® 2000 Professional Users Only..................................................11 For Windows® XP Users Only ...........................................................................14 For Parallel Interface Cable Users (For Windows® 98/98SE/Me/2000 Professional/XP)................................ 17 For Windows® 98/98SE/Me Users Only ............................................................ 19 For Windows® 2000 Professional Users Only..................................................20 For Windows® XP Users Only ...........................................................................24 Windows NT® Workstation Version 4.0 Users ................................. 27 For For Network Interface Cable Users (For Windows® 98/98SE/Me/NT/2000 Professional/XP).......................... 29 For USB Interface Cable Users................................................................. 32 For Mac OS® 8.6 to 9.2 .......................................................................................32 For Mac OS® X 10.1/10.2.1 or greater................................................................34 For Network Interface Cable Users .......................................................... 36 For Mac OS® 8.6 to 9.2 .......................................................................................36 For Mac OS® X 10.1/10.2.1 or greater................................................................38 For Administrators Network User's Guide Chapter Map (NC-9100h) .............................................. 40 Installing the BRAdmin Professional Configuration Utility (Windows® Users Only) .................................................................................... 41 Setting your IP Address, Subnet Mask and Gateway using BRAdmin Professional (Windows® Users Only)............................................. 42 Options ................................................................................................................. 43 Replacement Consumables................................................................................ 43 1 Step 1 Setting Up the Machine 4 Close the ADF cover. Install the Automatic 1 Document Feed (ADF) Support Do NOT connect the interface cable. Connecting the interface cable is done when installing the driver. 2 1 Open the ADF cover. Install the Drum Unit Assembly Open the front cover by pressing the front cover release button. 1 ADF Cover 2 Insert the tabs of ADF support into the holes of the ADF one side at a time. Tab Front Cover Release Button Hole Front Cover Tab ADF support 3 Push ADF Support down until it latches in place. 2 Unpack the drum unit assembly. Remove the protective part. Drum Unit Assembly Protective part 2 3 1 Pull the paper tray completely out of the DCP. 4 2 While pressing the paper guide release lever, slide the adjusters to fit the paper size. Check that the guides are firmly in the slots on the tray. Paper Guide Release Lever Windows® Network Universal Guide Release Button 5 Close the front cover of the DCP. 3 For Administrators Continued ... Macintosh® Network Macintosh® USB For Legal size paper, press the universal guide release button and pull out the rear of the paper tray. Windows NT® 4.0 Parallel Windows® Parallel Push the drum unit assembly into the DCP (until it snaps into place). Windows® USB Setting Up the Machine Rock it from side to side several times to distribute the toner evenly inside the assembly. 3 Load Paper in the Paper Tray Step 1 3 Setting Up the Machine 4 1 Fan the stack of paper well to avoid paper jams and misfeeds. Release the Scanner Lock Push the lever up to unlock the scanner. (The gray scanner lock lever is located at the back left under side of the document cover.) Scanner Lock Lever 4 Put paper in the paper tray. Check that the paper is flat in the tray and below the maximum paper mark. Up to here. 5 Install the Power Cord Do not connect the Parallel or USB cable yet. 1 5 Put the paper tray firmly back in the DCP and unfold the Support flap before you use the DCP. Make sure that the power switch is off. Connect the AC power cord to the DCP. Support Flap 2 Plug the AC power cord into an AC outlet. Turn the power switch on. For details on supported paper specifications, see "Paper" in Chapter 2 of the User's Guide. If Check Scan Lock appears on the LCD, immediately release the scanner lock and press Stop/Exit. 4 Norway, Sweden, Finland and Denmark only. You must set your country so that the DCP works correctly. (This function is not available on UK, Asia and Oceania machine.) Set Country Norway 1.Yes 2.No Accepted 1 Set Country 7 After the LCD returns to the copy mode, turn the power switch off, and then turn it on again. Windows® Parallel Press Set Key 7 Selecting Your Language You can change LCD Language. (This function is not available on UK, Asia and Oceania machine.) 2 Set Country Norway Sweden Finland Select & Set Press the Press the key. key. 5 Press the Stop/Exit key. 3 4 Press Set when the LCD shows your country. The LCD prompts you to make sure of the country again. Go to Next page to install the driver Set Country Norway 1.Yes 2.No Enter Number 5 If the LCD shows the correct country, press 1 to go to Step 6. --OR-- Press 2 to go back to Step 1 to select the country again. 5 For Administrators Macintosh® Network Macintosh® USB Windows® Network Press or to select your language, and then press the Set key. Windows NT® 4.0 Parallel Press or to select the country (NORWAY, SWEDEN, FINLAND or DENMARK). (Make sure you set your country, not your language.) 1 2 3 4 Press the Menu key. Windows® USB Check that the power is turned on by plugging in the power cord and turn the power switch on. Press Set. If you select "NORWAY" in step 4, the LCD shows Norwegean messages. Setting Up the Machine Selecting Your Country 6 (Not Language) 6 After the LCD shows Accepted for two seconds, it shows Vennligst vent. Step 2 Installing the Driver & Software Supplied CD-ROM "MFL-Pro Suite" The CD-ROM includes the following items: Install MFL-Pro Suite You can install the MFL-Pro Suite and multifunction drivers. Install Optional Applications You can install additional MFL-Pro Suite software utilities. Documentation*1 View the User's Guide and other documentation in PDF format (Viewer included). On-Line Registration You will be pointed to the Brother Product Registration Web page for quick registration of your machine. Brother Solutions Center Brother contact information and web site links offering the latest news and support information. Repair MFL-Pro Suite If you experience errors while installing the MFL-Pro Suite you can use this function to automatically repair and re-install the software. MFL-Pro Suite includes Printer Driver, Scanner Driver, ScanSoft® PaperPort® 9.0SE, ScanSoft® OmniPage® and True Type® fonts. PaperPort® 9.0SE is a document management application for viewing scanned documents. ScanSoft® OmniPage®, which is integrated into PaperPort® 9.0SE, is an OCR application that converts an image into text and inserts it into your default word processor. Start Here OS 8.6-9.2 You can install the printer driver, scanner driver and Presto!® PageManager® for Mac OS® 8.6 - 9.2. Start Here OSX You can install the printer driver, scanner driver, remote setup program and Presto!® PageManager® for Mac OS® 10.1/10.2.1 or greater. Readme! You can get important information and troubleshooting tips. Documentation*1 View the User's Guide and other documentation in PDF format. Brother Solutions Center You can access the Brother Solutions Center, a Web site offering information about your Brother product including FAQs, User's Guides, Driver updates and Tips for using the DCP. *1 The User's Guide on the CD-ROM includes the Software and Network User's Guide for features available when connected to a computer (e.g. Printing and scanning). 6 On-Line Registration You will be pointed to the Brother Product Registration Web Page for quick registration of the DCP. Step 2 Installing the Driver & Software Setting Up the Machine Follow the instructions on this page for your operating system and interface cable. Network Interface Cable Users............................ Go to page 29 (For Windows® 98/98SE/Me/NT/2000 Professional/XP) For Administrators ............................................... Go to page 40 7 For Administrators Macintosh® Network Network Interface Cable Users For Mac OS® 8.6 to 9.2 ..................................... Go to page 36 For Mac OS® X 10.1/10.2.1 or greater ............. Go to page 38 Macintosh® USB USB Interface Cable Users For Mac OS® 8.6 to 9.2 ..................................... Go to page 32 For Mac OS® X 10.1/10.2.1 or greater ............. Go to page 34 Windows® Network Windows NT® 4.0 Parallel Windows NT® Workstation Version 4.0 Us ...