User manual MUSTEK PL510T - Quick Start

82-179-01021 Portable DVD Player Quick Guide Welcome to this Portable DVD Player Quick Guide. Please carefully follow the instructions to set up your portable DVD player. Getting to Know Your Portable DVD Player FRONT VIEW DIAGRAM LCD screen SPEAKERS SPEAKERS LCD button SETUP button MODE button MENU button PAUSE/UP button F.FWD/RIGHT button PLAY/SEL. button NEXT button STOP/DOWN button PREVIOUS button Remote Sensor OPEN button F.BWD/LEFT button POWER indicator/Battery charge indicator LEFT SIDE DIAGRAM DC IN jack POWER button SD/MMC card slot Antenna/Cable TV signal Input jack 1 RIGHT SIDE DIAGRAM 1 1. 2. 3. 4. 2 3 4 5 6 5. 6. 7. 8. 7 8 Volume Adjustment scroll wheel Headphone jack Headphone jack Coaxial output jack AV out/AV in switch button Audio output/input jack Video output/input jack S-Video/P-Scan output jack REMOTE CONTROL DIAGRAM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. INFO. button Auto Search/SETUP button MODE button PAUSE/UP button F.BWD/LEFT button PLAY/SEL. button PREVIOUS button STOP/DOWN button Number buttons LCD button 11. 12. 13. 14. 15. 16. 17. 18. 19. TV Source/MENU button SUBTITLE button TITLE button ANGLE button F.FWD/RIGHT button AUDIO button NEXT button REPEAT 1/ALL button MUTE button 2 BATTERY INSTALLATION FOR THE REMOTE CONTROL Insert the battery and match the (+) and (-) on battery to the marks inside the battery compartment. Remember to remove the insulating Mylon piece from the battery. + First-time use: CR2025 Service life of battery 1. The battery normally lasts for about one year although this depends on how often and for what operations the remote control is used. 2. If the remote control unit fails to work even when it is operated near the player, replace the battery. 3. Use a 3V lithium battery. REMOTE CONTROL OPERATION RANGE Point the remote control unit no more than about 6 meters from the remote control sensor and within 600 of the front of the unit. remote sensor 30 The operating distance may vary according to the brightness of the room. Note: 1. Do not point bright lights at the remote control signal sensor. 2. Do not place objects between the remote control unit and the remote control signal sensor. 3. Do not use this remote control unit while simultaneously operating the remote control unit of any other equipment. 3 + OPEN PUSH Quick Operation Guide STEP 1. Connect to Power (A) Please connect the supplied AC adapter to the DC IN jack on the left side of the portable DVD player. (A) STEP 2. Connect earphones or connect to external equipment.(B) If you want to enjoy a better listening and viewing quality, you can connect the portable DVD player to external equipment, such as a TV or an amplifier. Note: 1. Before connecting, make sure to turn off the power on the portable DVD player and external equipment. 2. Make sure to slide AV OUT/IN switch to AV OUT. 4 (B) (Red) (White) (Yellow) (Blue) (Red) (Green) 1 2 3 4 Note: Make sure the external equipment supports the audio/video input feature. Back/front panel of external equipment 1 L (White) R (Red) Audio input 2 3 4 TV Video input TV S-Video S-Video input P-Scan TV Pb (Blue) Pr (Red) Y (Green) Video input 5 STEP 3. Open the display panel. (C) (C) STEP 4. Press POWER to turn on the portable DVD player. (D) (D) STEP 5. Press to open the disc cover. (E) (E) STEP 6. Gently hold the edge of the disc, then put it in the center with the printed side up. STEP 7. Close the disc cover. STEP 8. Press to play the disc. 6 INPUT FROM EXTERNAL EQUIPMENT You could input images and sound from external equipment by connecting the portable DVD player to external equipment with Audio cable or Video cable.(F) Note: Make sure to slide AV OUT/IN switch to AV IN. (F) (Red) (White) (Yellow) 1 2 Note: Make sure the external equipment supports the audio/ video output feature. External equipment with external output jack (example: audio output and video output) Back/front panel of external equipment 1 L (White) R (Red) Audio output 2 TV Video output 7 Using the Battery Pack Note: The shape of the following pack is only for reference; the actual shape may differ. Battery connectors Before using the battery pack, make sure to charge it. You can only charge the battery pack while the battery pack is attached to the portable DVD player. Battery Pack Information (Charge & Playback Time) Charge Time(hr) NiMH 4500mAh Li-ion 6300mAh 4.5 5.5 DVD Playback Time(hr) 2.5 3.5 A. How to charge the battery pack STEP 1. Please align the portable DVD player's battery connectors with the battery pack's battery connectors. Attach the battery pack to the portable DVD player as shown in figure (A). (A) Note: 1. Please turn Power off when attaching or removing the battery pack. 2. If you want to remove the battery pack, refer to "B. How to remove the battery pack from the portable DVD player." 8 STEP 2. Connect the AC adapter(12V, 1.25A) to the DC IN jack on the left side of the portable DVD player and a household power outlet as shown in figure (B). (B) STEP 3. The battery charge indicator will turn red and start charging. STEP 4. When the battery pack is fully charged, the battery charge indicator will be off. Note: 1. The battery pack is not charged while the portable DVD player is turned on. 2. Please use the specific power adapter (12V, 1.25A) to charge the battery pack. How to remove the battery pack from the portable DVD player STEP 1. Please follow the instructions on the back of the portable DVD B. player and slowly remove the battery pack from the unit as shown in figure (C). (C) Step 1 Step 2 9 MMC/SD Card Operation Note: You can only change the MMC/SD setting to "On" or "Off" while there is no disc inside the DVD player. << Important >> If you set the MMC/SD setting to "On", the portable DVD player can only read SD/MMC card. That is to say, the portable DVD player can't playback any discs. While the disc is played back, you can only press the button to switch to MMC/SD mode. : Move : Select SETUP: Quit Custom Setup MMC/SD Parental Ctrl Password Angle Mark On Off ... STEP 1. Insert the card as shown in figure (A). STEP 2. After a few minutes, the unit will enter File Manager mode. Press button or button to select the specific file. STEP 3. Press > to view the the preferred picture or < playback the selected MP3 file. << NOTE>> >> *Playable format: MP3/JPEG *If the JPEG file size is over 1.5MB, the portable DVD player needs more time to read it. << For JPEG pictures only>> >> button or button to rotate the picture. Press *Press *Press button to rotate left by 90 degrees. button to rotate right by 90 degrees. To remove the MMC/SD card Push the card as shown in figure (B). The card will pop out. (A) (B) 10 TV Tuner Operation Preparation In order to receive a TV signal, please connect the unit to the supplied antenna, to cable, or to satellite. STEP 1. Connect the RF coaxial cable or Aerial cable to Antenna/Cable TV signal input jack on the left side of the portable DVD player as shown in figure (A). (A) 4 2 5 3 1 1 3 5 Antenna/Cable TV signal input jack RF coaxial cable Receive TV signal from cable 2 4 Aerial cable Receive Antenna TV signal For using RF coaxial cable ONLY Before connecting the RF coaxial cable to Antenna/Cable TV signal input jack on the left side of the portable DVD player, remember to connect the RF coaxial cable with cable transfer as shown in the following diagram. NOTE: There are two kinds of cable transfers: one is for NTSC, the other is for PAL. (PAL) (NTSC) 11 For using Aerial cable ONLY After connecting the Aerial cable to Antenna/Cable TV signal input jack on the left side of the portable DVD player, remember to place the Aerial cable in proper position to receive the best TV signal. HOW TO USE TV TUNER Note: TV reception quality might differ from area to area. Quick operation guide STEP 1. Press Power on. STEP 2. Press Press to switch to "TV Tuner". a number of times. You can toggle between "S-Video", "P-Scan", "MMC/SD" or "TV Tuner". STEP 3. Press STEP 4. Press to choose the TV source from "Cable" . The tuner search starts automati or "Antenna". cally and allows the channel lineup to be confirmed. This process may take several minutes. <> 1. While doing Auto Search for the first time, the portable DVD player will select available TV channels. Yet, if more channels become available in your area, you may need to repeat the Auto Search to update the available channels. 2. While conducting an Auto Search, all stored programs will be erased and a new lineup will be written. *Before doing Auto Search, make sure to set the correct country setting in the Screen Setup. STEP 5. Press button to previous channel, or press button to advance to the next channel. 12 To select preferred available channels Press or to choose the preferred available channels. << NOTE>> This function only works with available channels. >> To select specific channel Press button or button to select the specific channel; or press the number button(s) to specify the specific channel. << NOTE>> >> 1. You can use this function to select a specific channel. All channels are available. 2. Example: Select Channel 25 by pressing "2" and "5" on the remote control. Mute function Press , the " " icon appears on the screen and the portable DVD player is muted. To resume sound Press again until the " " icon disappear on the screen. 13 Country Setting 1 2 Press Press in the stop mode. button / button to select . "Screen Setup", and then press 3 Press button / button to select "Country", and then press . button to select the 4 5 Press Press button / . Screen Setup TV Type Screen Saver TV System Video Output Country correct country setting. USA Japan : Move : Select SETUP: Quit To return to the SETUP MENU screen Press button. To finish the setup operation Press to exit or select EXIT from SETUP MENU screen. NTSC TV Tuner Canada, Japan, Korea, Panama, U.S., etc. 14