User manual INFOCUS SP4805 - Reference Guide

ScreenPlay 4805 User's Guide [ English · Français · Deutsch · Español · Italiano · Norsk · Nederlands] Declaration of Conformity Manufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville, Oregon 97070 USA European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands We declare under our sole responsibility that this projector conform to the following directives and norms: EMC Directive 89/336/EEC, Amended by 93/68/EEC EMC: EN 55022 EN 55024 EN 61000-3-2 EN 61000-3-3 Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC Safety: EN 60950: 2000 March, 2004 FCC Warning Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. Trademarks Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark of International Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated. Digital Light Processing is a trademark or registered trademark of Texas Instruments. Faroudja, DCDi, and TrueLife are trademarks or registered trademarks of Faroudja. InFocus and ScreenPlay are trademarks or registered trademarks of InFocus Corporation. InFocus, ProjectorManager, ProjectorNet, and LP are trademarks or registered trademarks of InFocus Corporation. Canada This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Agency Approvals UL, cUL, TUV, GOST Other specific Country Approvals may apply. Please see product certification label. InFocus reserves the right to alter product offerings and specifications at any time without notice. 1 Table of Contents Introduction Positioning the projector Projector and Device Connector Guide Computer connections Video connections Connecting a computer source Required computer connections Optional computer connections Displaying a computer source image Adjusting the image Using the projector with Windows 98 for the first time Connecting a video device Video device connections Composite (RCA) video connection S-video connection Component (RCA) connection DVI connection Displaying video Adjusting the image Shutting down the projector Troubleshooting your setup Using the remote control Using the audio Using the keypad buttons Optimizing computer images Optimizing video images Customizing the projector Using the menus Picture menu Settings menu Maintenance Cleaning the Lens Replacing the Projection Lamp Cleaning the Lamp Housing Screens Using the security lock Appendix Projected Image Size Red LED Behavior and Projector Errors 4 6 7 7 7 10 10 10 11 12 13 15 16 16 16 17 17 18 18 20 20 28 29 30 31 31 31 32 33 38 40 40 40 42 42 43 43 44 If you are experienced in setting up projection systems, use the Quick Setup card that is included with the projector. For complete details on connecting and operating the projector, refer to this User's Guide. Electronic versions of this User's Guide in multiple languages are available on our website. The website also has technical specifications (an interactive image size calculator, laptop activation commands, connector pin outs, a glossary, the product data sheet), a web store to buy accessories, and a page for online registration. 2 Important Operating Considerations for Safety · · Place the projector in a horizontal position no greater than 15 degrees off axis. Locate the projector in a well-ventilated area without any obstructions to intake or exhaust vents. Do not place the projector on a tablecloth or other soft covering that may block the vents. Locate the projector at least 4' (1.2 m) away from any heating or cooling vents. Use only InFocus-approved ceiling mounts. Use only the power cord provided. A surge-protected power strip is recommended. Refer to this manual for proper startup and shutdown procedures. In the unlikely event of the lamp rupturing, discard any edible items placed in the surrounding area and thoroughly clean the area along all sides of the projector. Wash hands after cleaning the area and handling the ruptured lamp. This product has a lamp which contains a very small amount of mercury. Dispose of it as required by local, state or federal ordinances and regulations. For more information see www.eiae.org. Do not place objects or people in the 2 foot (.6m) area along the front of the projector. For ceiling mount applications, this area should be 5 feet (1.5m). 2 ft ( .6m) · · · · · Follow these instructions to help ensure image quality and lamp life over the life of the projector. Failure to follow these instructions may affect the warranty. For complete details of the warranty, see the Warranty section at the end of this User's Guide. 5 ft (1.5m) 3 Introduction Congratulations and thank you for your excellent choice of a superior digital image projection device. Your new InFocus® ScreenPlayTM 4805 projector is specifically designed for home cinema applications. The ScreenPlay 4805 sets a high standard using the latest DLPTM technology and new DCDi Plus video processing from FaroudjaTM. Whether you are watching movies or High Definition broadcasts or playing the latest video game, you will enjoy amazing image quality. speaker keypad power cord connector power switch Product specifications To read the latest specifications on your multimedia projector, be sure to visit our website, as specifications are subject to change. Web address information is located on the back inside cover of this User's Guide. remote control receiver (IR) focus (thin ring) zoom (thick ring) tethered lens cap adjustable foot release Accessories The standard accessories that came with your projector can be found on the included packing list. Optional accessories are listed in the Accessories catalog that came with the projector and can also found on our website. See the inside back cover for the Web address. Online Registration Register your projector on our website to receive product updates, announcements, and registration incentives. See the inside back cover for the Web address. lamp housing door security lock connector panel adjustable foot 4 Connector Panel The projector provides both computer and video connection options, including: · · · · · · DVI (M1-DA) Component SD/ED/HD (RCA) S-video Composite audio/video (RCA) Audio out 12 volt DC output (see below) 12 volt DC output DVI audio out S-video RCA audio/visual (composite) RCA component The projector also provides the following connectors: 12 volt DC output The 3.5mm mini-jack trigger provides a 12 volt DC output. It provides a constant output while the projector is on. It has numerous uses. For example, if you connect your projection screen to the 12 volt DC output with the cable that came with your screen, when you turn on the projector the screen will move down; when you turn the projector off, the screen will return to the storage position. To use the 12 volt DC output, you must first remove the safety plug and turn Screen Trigger on in the System menu (see page 38). +12v ground 3.5mm plug 12 volt DC output to, for example, screen relay (see screen manufacturer for details) 5 Positioning the projector .5 12 To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Here are some general guidelines: · · Position the projector on a flat surface at a right angle to the screen. The projector must be at least 4.9 feet (1.49m) from the projection screen. Position the projector within 10 feet (3m) of your power source and within 6 feet (1.8m) of your video device (unless you purchase extension cables). To ensure adequate cable access, do not place the projector within 6 inches (.15m) of a wall or other object. If you are installing the projector on the ceiling, refer to the installation guide that comes with the Ceiling Mount Kit for more information. To turn the image upside down, see "Ceiling" on page 38. We recommend using an authorized ceiling mount. Position the projector the desired distance from the screen. The distance from the lens of the projector to the screen, the zoom setting, and the video format determine the size of the projected image. The top illustration to the right shows three projected image sizes. For more information about image sizes at different distances, see "Projected Image Size" on page 43. The image offset is 127.3% when the projector is in 16:9 mode. This means that if you have an image 10' high, the bottom of the image will be 2.73' above the center of the lens. See "Connecting a video device" on page 15 for additional information on 16:9 mode. ft. 5 ft . 3. 3 ft . 18.9 ft. 7.6 ft. 5 ft. · 10 ft high image Projection angle in 16:9 mode · bottom of image 2.73 ft above center of lens lens center · · 6 Projector and Device Connector Guide The following illustration and table should help you find the connectors to use and obtain the best resolution possible from your input devices, such as computers, standard VCRs, DVD players (progressive and interlaced), HDTV sources, TV and satellite tuners, camcorders, video games (progressive and interlaced), and laser disc players. Computer connections Computer connections involve attaching the VGA and USB ends of the provided computer cable to a computer and connecting the other end (M1 cable end) to the M1-DA input on the projector. The USB part of the computer cable allows you to advance slides in a PowerPointTM presentation via an optional remote control. See page 10 for computer/projector setup information. Video connections The first step for connecting video is deciding what type of output connector you want to connect to the projector. If there is more than one output, select the one with the highest quality. The best quality ranking, with 1 being the highest and 3 being the lowest, is: 1 component video (RCA) 2 S-video 3 audio/visual composite video (RCA) If your video device has a VGA connector, you can use the DVI connector on the back of the projector for very high quality. composite audio/visual (RCA) projector input connectors 12 volt DC output DVI (M1-DA) S-video audio out component (RCA) 7 Video Device Video Compatibility If Your Device Connector Is Attach to Adapter or Labeled Connector on Projector For Setup Instructions, see Comments Standard Broadcast TV (not HDTV) via: cable, digital cable, satellite TV, DVD, or VCR NTSC, PAL, and SECAM formats Component 480i Composite video or S-video Component Video Video or S-video Composite (RCA) video connection on page 16. Component on page 17. Not for progressive (i.e. HDTV) sources. See page 9. Component Standard Video Camera NTSC, PAL, and SECAM formats Component 480i Composite video or S-video Component Video Video or S-video Composite (RCA) video connection on page 16. Component on page 17. Not for progressive (i.e. HDTV) sources. See page 9. Component Standard Video Game NTSC, PAL, and SECAM formats Component 480i Composite video or S-video Component Video Video or S-video Composite (RCA) video connection on page 16. Component on page 17. Not for progressive (i.e. HDTV) sources. See page 9. Component 8 Video Device Video Compatibility If Your Device Connector Is Attach to Adapter or Labeled Connector on Projector For Setup Instructions, see Comments HDTV (High Definition TV) 1035i, 1080i, 720p Component 1080i, 720p DVI Component video M1-DA (DVI) Component DVI connection on page 17 Component on page 17 1035i, 1080i, 720p Progressive DVD Component 480i, 480p, 576i, 576p DVI Component video M1-DA (DVI) Component DVI connection on page 17 Component on page 17 1035i, 1080i, 720p Progressive Video Game Component 480i, 480p, 576i, 576p DVI Component video M1-DA (DVI) Component DVI connection on page 17 Component on page 17 9 Connecting a computer source Required computer connections Connect one end of the provided computer cable (see page 15 for connecting video devices) to the blue M1-DA connector on the projector. Connect the other ends (USB and VESA) to the USB and VGA ports on your computer. If you are using a desktop computer, you will need to disconnect the monitor cable from the computer's video port first. This connection allows you to advance slides in a PowerPoint presentation using an optional remote. USB drivers must be installed to use the USB feature. For more information, see page 14. Connect the black power cord to the Power connector on the side of the projector and to your electrical outlet. NOTE: Always use the power cord that shipped with the projector. connect computer cable connect power cable connect audio cable Optional computer connections To have sound with your presentation, connect an audio cable (not included) to your computer and to the red and/or white Audio In connectors on the projector. 10 Displaying a computer source image Remove the lens cap. remove lens cap Toggle the Power switch on the side of the projector to the On position. The LED flashes green and the fans start to run. When the lamp comes on, the start up screen displays and the LED is steady green. It can take a minute for the image to achieve full brightness. ? No start up screen? Get help on page 20. toggle Power switch Turn on your computer. The computer's image should appear on the projection screen. If it doesn't, press the Computer button on the projector's keypad. If your computer has Windows 98 as its operating system, see "Using the projector with Windows 98 for the first time" on page 13 regarding the driver setup process. turn on computer Make sure your laptop's external video port is active. Many laptops do not automatically turn on their external video port when a projector is connected. Usually a key combination like FN + F8 or CRT/LCD key turns the external display on and off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol. Press FN and the labeled function key simultaneously. Refer to your laptop's documentation to learn your laptop's key combination. ? No laptop image? Try pressing the Auto Image button on the keypad. Get help on page 21. activate laptop's external port monitor key or LCD/CRT key FN key 11 Adjusting the image If necessary, adjust the height of the projector by pressing the release button to extend the foot. If necessary, rotate the leveling foot located at the rear of the projector. Avoid placing your hands near the hot exhaust vent in front of the projector. Position the projector the desired distance from the screen at a 90 degree angle to the screen. See page 43 for a table listing screen sizes and distances. elevator foot adjust distance release button adjust height rotate leveling foot Adjust the zoom or focus. adjust zoom or focus focus (thin ring) zoom (thick ring) If the image is not square, adjust the keystone using the buttons on the keypad. Press the top Keystone button to reduce the upper part of the image, and press the bottom Keystone button to reduce the lower part. adjust keystone Adjust the Contrast or Brightness in the Picture menu. See page 33 for help with these menu adjustments. adjust Picture menu 12 Using the projector with Windows 98 for the first time The first time you connect a computer running Windows 98 to the projector, the computer recognizes the projector as "new hardware" and the Add New Hardware Wizard appears. Follow these instructions to use the Wizard to load the correct driver (which was installed with your Windows operating system). If you are running Windows 2000 or Windows ME, skip these steps and go to "Adjusting the image" on page 12. a a Click Next to begin searching for the driver. b b Make sure "Search for the best driver" is selected, then click Next. c Uncheck any checked boxes, then click Next. Windows automatically locates the driver. If this driver has been removed, reload the driver using your Windows operating system CD. c d When Windows finds the driver, you are ready to install it. Click Next. d 13 Skip this page if you did not connect a USB mouse cable For Windows 98: · · If you connected the USB cable, the Add New Hardware Wizard appears again. Drivers must be installed to use the USB functionality. The Wizard launches three times. The first time it detects a USB Composite Device. The second time a USB Human Interface Device (for the keyboard). The third time it detects a USB Human Interface Device (for the mouse). For Windows 2000, Windows ME, and Windows XP: · The USB drivers are automatically installed. 14 Connecting a video device You can connect video devices such as VCRs, DVD players, camcorders, digital cameras, video game consoles, HDTV receivers, and TV tuners to the projector. There is also an audio input via the red and white A/V connectors. You can connect the audio directly to the projector to get sound from the built-in speaker, or you can connect the audio to your stereo system via the Audio Out connector. You can connect the projector to most video devices that can output video. You cannot directly connect the coaxial cable that enters your house from a cable or satellite company, the signal must pass through a tuner first. Examples of tuners are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes. Basically, any device that can change channels is considered a tuner. Before connecting your projector, you should decide which aspect ratio you want to use. The projector's Aspect Ratio setting is accessed through the projector's Picture Menu. See page 33 for more information. 16:9 aspect ratio 9 4:3 image input Native aspect ratio 4:3 image on 16:9 screen 3 9 4 16 16:9 image input 9 16:9 image 16 16 What is Aspect Ratio? Aspect ratio is the ratio of the image width to image height. HDTV and most DVDs are 16:9, which is the default for this projector. This projector is not intended for use with 4:3 screens. When in 4:3 mode the projector places black bars on both sides of the image. Native mode centers the image and turns off the internal scaler so that any resolution larger than 854x480 is cropped on the edges. Letterbox expands the image to fill the screen. If you are projecting onto a screen, the size/shape of the screen may determine which aspect ratio to use. If you are projecting onto a blank wall, you don't have the screen size restriction. What you plan to project will also help you choose between 4:3 and 16:9. For example, most TV shows are 4:3, while most movies are 16:9. If you have a 16:9 screen, then you should select an aspect ratio of 16:9 for anamorphic movies and HDTV, and Native for 4:3 content. If you have a 4:3 screen you should still use 16:9 for anamorphic movies or HDTV, but you also have the option of using either 4:3 or Native for 4:3 content. Keep in mind that anamorphic movies only appear correctly if the DVD player is set to output to a 16:9 television. 4:3 image input 4:3 image on 16:9 screen black bars 4:3 aspect ratio 9 4 letterbox image input black bars 16 16:9 image fills 16:9 screen letterbox aspect ratio 3 black bars 9 4 16 15 black bars 3 Video device connections Composite (RCA) video connection Plug the provided composite A/V cable's yellow connector into the videoout connector on the video device. Plug the other yellow connector into the yellow Video connector on the projector. Plug a white connector into the left audio out connector on the video device and plug a red connector into the right audio out connector on the video device. Plug the remaining white connector into the white audio in connector on the projector, and plug the remaining red connector into the red audio in connector on the projector. Keep in mind that video output from composite connections are not as high quality as S-video or component video. connect A/V cable S-video connection If your video device uses a round, seven-prong S-video connector, plug the S-video cable into the S-video connector on your video device and into the S-video connector on the projector. Use the A/V cable's red and white audio connectors as described directly above (the yellow connectors on the A/V cable are not used). Keep in mind that S-video delivers higher quality video output than composite, but not as high as component video. connect S-video and composite audio cables 16 Component (RCA) connection To connect a progressive scan DVD or HD source, use the component connector. Connect a component video cable with red, green, and blue RCA connectors (available at Consumer Electronic stores) into the source device's component connector. Connect the other three ends of the component cable into the Component connector on the projector. Use the composite A/V cable's red and white audio connectors as described on the previous page (the yellow connectors on the A/V cable are not used). Keep in mind that component video delivers higher quality video output than s-video or composite video. connect component composite audio cables DVI connection If your video device uses a DVI connector, plug the DVI end of the M1-D cable (sold separately) into the video-out connector on the video device. This connector may be labeled "To Monitor" on the video source. Plug the M1 computer end of the cable into the M1-DA connector on the projector. Use the composite A/V cable's red and white audio connectors as described on the previous page (the yellow connectors on the A/V cable are not used). Keep in mind that DVI video delivers the highest quality video output. Connect the power cord to the Power connector on the side of the projector and to your electrical outlet. NOTE: Always use the power cord that shipped with the projector. connect DVI and composite audio cables connect power cable 17 Displaying video Remove the lens cap. remove lens cap Toggle the Power switch on the side of the projector to the On position. The LED flashes green and the fans start to run. When the lamp comes on, the start-up screen is displayed and the LED is steady green. It can take a minute for the image to achieve full brightness. ? No start up screen? Get help on page 21. Plug in and turn on your video device. The video device's image should appear on the projection screen. If it doesn't, press the Video button on the keypad. ? No image? Try pressing the Source or Auto Image Get help on page 21. toggle Power switch turn on video device Adjusting the image Adjust the height of the projector by pressing the release button to extend the foot. Rotate the leveling foot at the rear of the projector, if necessary. adjust height rotate leveling foot elevator foot release button Position the projector the desired distance from the screen at a 90 degree angle to the screen. See page 43 for a table listing screen sizes and distances to the screen. adjust distance 18 Adjust the zoom and focus. adjust zoom and focus focus (thin ring) zoom (thick ring) If the image is not square, adjust the keystone using the buttons on the keypad. Press the top Keystone button to reduce the upper part of the image, and press the bottom Keystone button to reduce the lower part. adjust keystone Adjust the volume on the keypad or remote. adjust volume Adjust the Contrast, Brightness, Color, Tint, or Aspect Ratio in the Picture menu. See page 33 for help with the menus and these adjustments. For Aspect Ratio, keep in mind that DVD players must be configured for 16:9 in order to view the highest quality image. For more information regarding Aspect Ratio, see page 15. adjust Picture menu options including Aspect Ratio 19 Shutting down the projector The projector automatically displays a black screen after no active source is detected for 30 minutes. This black screen helps preserve the life of the projector. The image returns when an active source is detected or a remote or keypad button is pressed. Troubleshooting your setup If your image appears correctly on the screen, skip to the next section. If it does not, troubleshoot the setup. The LED on top of the projector indicates the state of the projector and can help you troubleshoot. Screen Save You can make the black screen appear after a preset number of minutes by turning on the Screen Save feature in the Settings>System menu. See page 38. Table 1: LED behavior and meaning LED color/behavior solid green Meaning The power switch has been toggled on and the software has initialized or the projector has been powered off via the remote. The power switch has been toggled on and the software is initializing, or the projector is powering down and the fans are running to cool the lamp. A fan or lamp failure has occurred. Make sure the vents aren't blocked (see page 26). Turn off the projector and wait one minute, then turn the projector on again. If the projector has been working exceeded its lamp life (page 40), replace the lamp and reset the lamp timer. Contact Technical Support if the problem persists. An unidentifiable error: please contact Technical Support. Power Save The projector also has a Power Save feature that automatically turns the lamp off after no active sources are detected and no user interaction with the projector is performed for 20 minutes. By default, this feature is off. See page 38. blinking green Turning off the projector You can turn the projector off simply by toggling the power switch to the off position. You can also press the remote's Power button to place the projector in the Off state while it is running. When the Power button is pressed twice (once to start the power-down process and a second time to verify that you want to power the projector off), the lamp turns off and the LED blinks green for one (1) minute while the fans continue to run to cool the lamp. While the LED is blinking green, the projector does not accept any keypad and remote control input. When the lamp has cooled, the LED lights solid green and the fans slow down to minimal speed. To turn off the projector, toggle the power switch to the off position. NOTE: Once the projector has been toggled off, you must wait for one (1) minute before turning the projector on again. This allows the lamp to properly cool. However, if the remote was used to power the projector to the Off state you do not need to wait one minute to turn it on again. blinking red see page 44 for more information solid red The following tables show common problems. In some cases, more than one possible solution is provided. Try the solutions in the order they are presented. When the problem is solved, you can skip the additional solutions. 20 Problem no start up screen Solution plug power cord in projector's left side remove lens cap toggle power switch toggle power switch on side Result correct image Start u Scre p en only start up screen appears press the Computer button activate laptop's external port Startu p Scree n computer image projected A A restart laptop A 21 Problem no computer image, just the words "Signal out of range" Solution press the Auto Image button on keypad Result computer image projected A Signa l rang out of e adjust computer refresh rate in Control Panel>Display>Settings>Advanced>Adapter (location varies by operating system) A A you may also need to set a different resolution on your computer, as shown in the following problem, "image fuzzy or cropped" 22 Problem image fuzzy or cropped Solution set your computer's display resolution to the native resolution of the projector (Start>Settings>Control Panel>Display>Settings tab) select 854x480 Result image clear and not cropped A A A For a laptop, disable laptop monitor or turn-on dualdisplay mode move projector, adjust zoom, adjust height image not centered on screen correct image adjust horizontal or vertical position in Picture>Advanced menu 23 Problem image not square Solution adjust Keystone on keypad Result square image image not sharp adjust Sharpness (video sources only) in the Picture>Advanced menu correct image AB AB 24 Problem image upside down Solution turn off ceiling in Settings>System menu Result correct image AB turn off rear in Settings>System menu correct image image reversed left to right projected colors don't match source COLOR 25 AB A adjust color, tint, color temperature, brightness, contrast in the menus AB correct image COLOR Problem The video embedded in my PowerPoint presentation does not play on the screen Solution Turn off the internal LCD display on your laptop Result Embedded video plays correctly A A B A B lamp won't turn on, LED blinking red make sure vents aren't blocked, turn off the projector and allow it to cool for one minute lamp turns on LED Start u Scre p en 26 Problem "Change lamp" message appears at startup or lamp won't turn on and LED blinking red Solution lamp must be replaced (see page 40) Result lamp turns on LED Start u Scre p en replace lamp Still need assistance? If you need assistance, visit our website or call us. See the inside of the back cover for support contact information. This product is backed by a limited warranty. An extended warranty plan may be purchased from your dealer. When sending the projector in for repair, we recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit. Please insure your shipment for its full value. 27 Using the remote control The remote uses two (2) provided AA batteries. They are easily installed by sliding the cover off the remote's back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover. To operate, point the remote at the projection screen or at the projector (not at the video device or computer). The range of optimum operation is up to 30 feet (9.14m). Press the remote's Menu button to open the projector's menu system. Use the arrow buttons to navigate, and the Select button to select features and adjust values in the menus. See page 32 for more info on the menus. The remote also has: · · · · · · · · · · · Power button to turn the projector on and off (see page 20 for shutdown info) backlight button to light the remote's buttons in the dark Brightness and Contrast buttons to adjust the image Blank button to display a blank screen instead of the current image (to change the color of the screen, see page 39) Source buttons to switch among sources (to assign a particular source to a source button, see page 38) and a source toggle Resize button to change the Aspect Ratio (see page 33) Auto Image button to resynch the projector to the source Preset button to restore stored settings (see page 34) Overscan button to remove noise in a video image (page 37) Make sure the batteries are installed in the proper orientation and are not dead. Make sure you're pointing the remote at the projector or the screen, not at the video device or the computer, and are within the remote range of 30 feet (9.14m). backlight button navigation buttons Troubleshooting the remote 28 Using the audio Using the projector's speakers To use the projector's speaker, connect your source to the Audio In connectors (L and/or R) on the projector's composite connectors. To adjust the volume, press the Volume buttons on the keypad or remote. To mute the sound, press the Mute button on the remote. Troubleshooting Audio If you aren't hearing the audio, check the following: · · · · · · Make sure the audio cable is connected. Make sure mute is not active (press the Mute button on the remote). Make sure the volume is turned up enough. Press the Volume button on the keypad or remote. Make sure the correct source is active. Adjust the audio source. If playing a video, make sure the playback has not been paused. adjust volume connect audio cable Connecting external speakers The projector can be attached to external speakers that have their own power source by plugging a speaker cable (not included) into the projector's Audio Out connector. external speakers with own power source audio out speaker cable 29 Using the keypad buttons Most buttons are described in detail in other sections, but here is an overview of their functions: Menu­opens the on-screen menus (page 32). Select­confirms choices made in the menus (page 32). Up/Down arrows­navigates to and adjusts settings in the menus (page 32). Auto Image­resets the projector to the source. Presets­cycles through the available preset settings (page 34). Keystone­adjusts squareness of the image (page 12). Volume­adjusts sound (page 29). Video and Computer­changes the active source. menu navigation buttons 30 Optimizing computer images After your computer is connected properly and the computer's image is on the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 32. · · · · · Adjust the Keystone, Contrast, or Brightness in the Picture menu (page 33). Change the Aspect Ratio. Choose the option that best fits your input source (page 33). Adjust the Color Temperature in the Advanced menu (page 35). Adjust the Phase, Tracking, or Horizontal or Vertical position in the Advanced menu (page 37). Once you have optimized the image for a particular source, you can save the settings using Presets. This allows you to quickly recall these settings later (page 34). · · press the Resize button on the remote to cycle through the options. See page 28. Select a specific Color Space. See page 36. Select a different Video Standard. Auto tries to determine the standard of the incoming video. Select a different standard if necessary. See page 37. Make sure your DVD player is set for a 16:9 television. See your DVD player's user's guide for instructions. · Customizing the projector You can customize the projector for your specific setup and needs. See page 38 to page 40 for details on these features. · · · · · · · · For rear projection, turn rear mode on in the Settings>System menu. For ceiling mounted projection, turn ceiling mode on in the Settings>System menu. Specify which source the projector checks first for active video during power-up. Turn the projector's display messages on and off. Turn on power saving features. Specify blank screen colors and start up logos. Specify the language viewed on the menus. Save settings for the active source as a preset. Optimizing video images After your video device is connected properly and the image is on the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 32. · · · · · · Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture menu (page 33). Select a Sharpness setting (page 35). Use the Color Control to adjust the color gain (page 36). Adjust the Color Temperature. Select a listed value (page 36). Turn on Overscan to remove noise on the edges of the video image (page 37). Change the Aspect ratio (page 33). Aspect ratio is the ratio of the image width to image height. TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are 1.78:1, or 16:9 (the projector's default). Choose the option that best fits your input source in the menus, or 31 Using the menus To open the menus, press the Menu button on the keypad or remote. (The menus automatically close after 60 seconds if no buttons are pressed.) The Main menu appears. Use the arrow buttons to move up and down to highlight the desired submenu, then press the Select button. To change a menu setting, highlight it, press Select, then use the up and down arrow buttons to adjust the value, select an option using radio buttons, or turn the feature on or off using check boxes. Press Select to confirm your changes. Use the arrows to navigate to another setting. When your adjustments are complete, navigate to Previous or Exit, then press Select to go to the previous menu; press the Menu button at any time to close the menus. Dots appears before the menu name. The number of dots indicate menu's level, ranging from one (the Main menu) to four (the most nested menus). The menus are grouped by usage: · · · The Picture menu provides image adjustments. The Settings menu provides set-up type adjustments that are not changed often. The About menu provides a read-only display of information about the projector and source. Main menu keypad navigation buttons Picture menu dots Settings menu Certain menu items may not be visible or may be grayed depending upon a particular source being connected. For example, Sharpness is only available for video sources and is not visible when a computer source is active. Differences are also seen in analog versus digital video sources and interlaced versus progressive sources. Menu options are grayed out only if the source if selected but no signal is present. For example, if the projector is set to a video source but the source, such as a DVD player, is turned off video menu options are grayed out. About menu 32 Picture menu To adjust the following settings, highlight the setting, press Select, use the up and down arrows to adjust the values, then press Select to confirm the changes. Keystone: adjusts the image vertically and makes a squarer image. You can also adjust keystone from the keypad. Contrast: controls the degree of difference between the lightest and darkest parts of the picture and changes the amount of black and white in the image. Brightness: changes the intensity of the image. Color: adjusts a video image from black and white to fully saturated color. The color setting applies to video sources only. Tint: adjusts the red-green color balance in the image of NTSC video images. The tint setting applies to NTSC video sources only. Aspect Ratio: Aspect ratio is the ratio of the image width to image height. TV screens are usually 4:3. HDTV and most DVDs are 16:9. The projector's default is 16:9. See "What is Aspect Ratio?" on page 15for more information. Select Native to see the unmodified input with no resizing by the projector. Select 16:9 to watch enhanced widescreen DVDs. Select Letterbox to preserve the 16:9 aspect ratio. If you have a 16:9 source and screen, the image fills the screen. If your source is letterboxed, the image is expanded to fill the screen. For more information regarding Aspect Ratio, see page 15. Picture menu increasing keystone decreasing keystone Aspect ratio 33 Presets: This allows you to customize settings and save the settings to be restored later. To restore the factory default settings, choose Factory Reset in the Settings>Service menu. To set a preset for the current source, adjust the image, select Save Settings in the Presets menu, then choose Save User 1, 2, or 3. You can recall these settings in the future by selecting the appropriate user presets. Gamma: Gamma tables contain preset intensity configurations optimized for the input source. You can select a gamma table that has been specifically tuned for either film, CRT (Cathode Ray Tube), video, Bright Room, or PC input. (Film input is material originally captured on a film camera, like a movie; video input is material originally captured on a video camera, like a TV show or sporting event.) White Peaking increases the brightness of whites that are near 100%. NOTE: Your viewing preferences may vary. Cycle through the gamma options and pick the one you like the best. Presets Save User Settings 34 Advanced menu Remember that not all options in the menus are available for all sources/ signals. The following 5 options are only available for composite, S-video, or component 480i sources. Chroma Detail: This adjusts the color sharpness. Luma Detail: This adjusts the overall sharpness (edge enhancement) of the Luma signal. Advanced menu Noise Reduction Noise Reduction: adjusts signal noise reduction. Choose Off to have no noise reduction, choose Auto to have the software determine the amount of noise reduction, or choose Manual and adjust the Level. CCS: (Cross Color Suppression) processes the signal to remove any color information from the luma portion of the signal. It is On for all composite signals, and can be turned off for S-video and interlaced component signals. Sharpness Sharpness: (video sources only) changes the clarity of the edges of a video image. Select a sharpness setting. 35 Color Space: This option applies to computer and component video sources. It allows you to select a color space that has been specifically tuned for the input signal. When Auto is selected, the projector automatically determines the standard. To choose a different setting, turn off Auto, then choose RGB for computer sources, choose either REC709 or REC601 for component video sources. Color Space Color Temperature: changes the intensity of the colors. Select a value. Color Temperature Color Control: allows you to individually adjust the gain (relative warmth of the color) of the red, green, and blue colors. Color Control 36 Video Standard: when it is set to Auto, the projector attempts to automatically pick the video standard based on the input signal it receives. (The video standard options may vary depending on your region of the world.) If the projector is unable to detect the correct standard, the colors may not look right or the image may appear "torn." If this happens, manually select a video standard by selecting NTSC, PAL, or SECAM from the Video Standard menu. Overscan: (video sources only) removes noise around the video image. Sync Threshold Adjust: (progressive signals only) If a hardware device, such as a DVD player, is not syncing properly with the projector, adjust this option to help it to sync when connected to the projector. The following four (4) options are for progressive and computer sources only. Phase: adjusts the horizontal phase of a computer source. Tracking: adjusts the vertical scan of a computer source. Horizontal/Vertical Position: adjusts the position of a computer source. Video Standard 37 Settings menu Audio: allows adjustments to Volume of the internal speaker and allows a chime to play when starting the projector. Adjustments can also be made from the projector's keypad and the remote. Sources: determines which source the projector checks first for active video during power-up. When Autosource is selected, the Source Enable feature indicates which sources the projector attempts to lock onto. You can use the Source Enable feature to eliminate certain sources from this search, which will speed the search. The source options are Computer for a computer, progressive DVD, or HDTV source, Video 1 for S-video connections, Video 2 for component video connections and Video 3 for composite video sources. By default, the check boxes for all sources are checked. Uncheck a source box to eliminate it from the search. When Autosource is not checked, the projector defaults to the source selected in Sources. To display another source, you must manually select one by pressing the Computer or Video button on the remote or keypad. System>Rear: reverses the image so you can project from behind a translucent screen. Ceiling: turns the image upside down for ceiling-mounted projection. Low Power: toggles between on and off. Turn it on to lower the light output of the lamp. This also lowers the fan speed, making the projector quieter. Display Messages: displays status messages (such as "Searching" or "Mute") in the lower-left corner of the screen.Translucent OSD: makes the menus translucent. This prevents the image from being completely covered by the menus while you are making image adjustments. Screen Saver Off: prevents the screensaver on your computer from being activated if the USB portion of the M1 is plugged into the computer. This function was previously called NND. Screen Trigger: turns on the 12 volt DC output switch on the connector panel. Power Save: automatically turns the lamp off after no signals are detected for 20 minutes. After 10 additional minutes with no signal, the projector powers down. If an active signal is received before the projector powers down, the image will be displayed. After an additional 10 minutes with no signal, the projector powers down and can be toggled off. If an active signal is received before the projector powers down, the image will be displayed. Settings menu Audio Sources Source Enable System menu 38 Startup Logo: allows you to display a blank screen instead of the default screen at startup, and when no source is detected. Blank Screen: determines what color is displayed when you press the Blank button on the remote. Startup Logo Blank Screen Language: allows you to select a language for the onscreen display. Language menu Service: To use these features, highlight them and press Select. Factory Reset: restores all settings to their default. Lamp Reset: resets the lamp hours used counter in the About menu to zero. Do this only after changing the lamp. Service Code: only used by authorized service personnel. About: provides information about the projector and the active source. Service menu About menu 39 Maintenance Cleaning the Lens 1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth. · Avoid using an excessive amount of cleaner, and don't apply the cleaner directly to the lens. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens. 2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you don't intend to use the projector immediately, replace the lens cap. Replacing the Projection Lamp The lamp hours used timer in the About menu counts the number of hours the lamp has been in use. Twenty hours before the lamp life expires, the message "Change lamp" appears on the screen at startup. If the maximum lamp time is exceeded, the lamp will not light. In this case, after replacing the lamp you must reset the lamp hours by simultaneously pressing both Volume buttons on the keypad and holding them for 10 seconds. NOTE: You can order new lamp housings from your dealer. See the Packing list for information. Use only a replacement lamp with the same type and rating as the original lamp. Lamp hours used turn off and unplug projector wait 30 minutes 1 Turn off the projector and unplug the power cord. 2 Wait 30 minutes to allow the projector to cool thoroughly. 3 Turn the projector on its side so that the lamp door is facing you. Using a flat-blade screwdriver, gently pry the lamp door from the projector by placing the screwdriver blade into the space between the top of the lamp door and the projector. lamp door 40 4 Loosen the two captive screws that attach the lamp housing to the projector. 5 Detach the lamp connector from the projector by depressing the locking tab on the connector and lightly pulling it free. WARNING: To avoid burns, allow the projector to cool for at least 30 minutes before you replace the lamp. Do not drop the lamp housing or touch the glass bulb! The glass may shatter and cause injury. Be extremely careful when removing the lamp housing. In the unlikely event that the bulb ruptures, small glass fragments may be generated. The lamp housing is designed to contain these fragments, but use caution when removing the lamp housing. Before replacing the lamp, clean the lamp compartment and dispose of cleaning materials. Wash hands after lamp replacement. This product has a lamp which contains a very small amount of mercury. Dispose of it as required by local, state or federal ordinances and regulations. For more information see www.eiae.org. lamp connector lamp cable lamp housing captive screw connector locking tab lamp housing captive screw lamp cable 6 Carefully remove the lamp housing. Dispose of the lamp in an environmentally proper manner. 7 Install the new lamp housing and tighten the screws. 8 Re-attach the lamp connector to the projector. The locking tab should engage when the connector is fully plugged in. 9 Replace the lamp door. 10 Plug in the power cord and toggle the Power switch to turn the projector back on. 11 To reset the lamp hour timer, navigate to the Settings>Service menu and select Lamp Reset. See page 40 for details. Service menu 41