User manual NEC LT260 - Reference Guide

Basic Serial Control Codes For NEC Projectors Models: GT5000/6000 MT860/1060/1065/1075 LT220/240/240K/260/260K WT600 VT770 VT46/465/460/560/660/660K HT1000/1100 Empowered by Innovation NEC Read First The following pages include the `basic' serial control codes for each model/series of NEC projectors. Only the basic serial control codes are provided in this document. NEC does not distribute the `full' serial control code set. NEC will supply more advanced control codes upon request. Please contact the NEC rep you purchased the projector from for more advanced control codes. In your request, you will need to give specific projector functions that you wish to control and only those codes will be supplied. nec For more information visit www.necvisualsystems.com For Customer Service call (800) 836-0655 NEC is a registered trademark of NEC Corporation. All other trademarks are the property of their respective owners. All information is subject to change without notice. NEC Solutions (Americia), Inc. Visual Systems Division 1250 Arlington Heights Rd., Suite 400 Itasca, IL 60143-1248 v1.1e GT5000/6000 Control Codes Function POWER ON POWER OFF INPUT SELECT RGB 1 INPUT SELECT RGB 2 INPUT SELECT VIDEO INPUT SELECT S-VIDEO INPUT SELECT DVI (DIGITAL) INPUT SELECT VIEWER LAN SLOT 1-1 SLOT 1-2 SLOT 2-1 SLOT 2-2 RGB1(VIDEO) RGB1(S-VIDEO) PICTURE MUTE ON PICTURE MUTE OFF SOUND MUTE ON SOUND MUTE OFF ON SCREEN MUTE ON ON SCREEN MUTE OFF ASPECT RATIO 1.25:1 (5:4) 1.33:1 (4:3) 1.78:1 (16:9) 1.85:1 2.35:1 AUTO ADJUST Code Data 02H 00H 02H 01H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 10H 02H 11H 02H 12H 02H 13H 02H 14H 02H 15H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 02H 0FH 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 02H 02H 02H 02H 02H 02H 02H 02H 02H 02H 02H 02H 02H 00H 00H 00H 00H 00H 00H 05H 05H 05H 05H 05H 02H 02H 03H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 12H 13H 14H 15H 16H 17H 18H 18H 18H 18H 18H 05H 01H 02H 06H 0BH 1AH 1FH 20H 24H 25H 29H 2AH 07H 0CH 09H 0AH 0EH 13H 22H 27H 28H 2CH 2DH 31H 32H 0FH 14H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 18H 00H 01H 02H 03H 04H 00H 00H 00H 00H 00H 30H 31H 32H 33H 34H Note: Contact your NEC rep for codes not listed. Cable Connection Communication Protocol: Baud Rate: 38400 bps Data Length: 8 bits Parity: No Parity Stop Bit: One bit X on/off: None Communications: Full duplex PC Control Connector (D-Sub 9P) To TxD of PC To RxD of PC To GND of PC 1 2 67 3 8 4 9 5 To RTS of PC To CTS of PC NOTE1: It is recommended to set the projector to "Idle Mode" in the Setup menu for best Power ON response. NOTE2: Pins 1, 4, 6, and 9 are used inside the projector. NOTE3: Jumper "Request to send" and "Clear to Send" together on both ends of the cable to simplify cable connection. NOTE4: For long cable runs it is recommended to set communication speed to 9600 bps in the Setup menu. MT860/1060/1065/1075 Control Codes Function POWER ON POWER OFF INPUT SELECT RGB 1 INPUT SELECT RGB 2 INPUT SELECT VIDEO INPUT SELECT S-VIDEO INPUT SELECT DVI (DIGITAL) INPUT SELECT VIEWER PICTURE MUTE ON PICTURE MUTE OFF SOUND MUTE ON SOUND MUTE OFF ON SCREEN MUTE ON ON SCREEN MUTE OFF ASPECT RATIO (4:3 Screen) 4:3 Letterbox Widescreen Crop ASPECT RATIO (16:9 Screen) 4:3 Window Letterbox Widescreen 4:3 Fill AUTO ADJUST Code Data 02H 00H 02H 01H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 10H 02H 11H 02H 12H 02H 13H 02H 14H 02H 15H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 02H 0FH 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 02H 02H 02H 02H 02H 02H 00H 00H 00H 00H 00H 00H 05H 05H 05H 05H 05H 05H 05H 05H 02H 02H 03H 01H 01H 01H 01H 01H 01H 12H 13H 14H 15H 16H 17H 18H 18H 18H 18H 18H 18H 18H 18H DDH 01H 02H 06H 0BH 1AH 1FH 09H 0AH 0EH 13H 22H 27H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H F0H 00H 01H 02H 03H 00H 01H 02H 04H 00H 00H 00H 00H 00H 00H 00H 00H 30H 31H 32H 33H 30H 31H 32H 34H NOTE: Contact your NEC rep for codes not listed. Cable Connection Communication Protocol: Baud Rate: 38400 bps Data Length: 8 bits Parity: No Parity Stop Bit: One bit X on/off: None Communications: Full duplex PC Control Connector (D-Sub 9P) To TxD of PC To RxD of PC To GND of PC 1 2 67 3 8 4 9 5 To RTS of PC To CTS of PC NOTE 1: It is recommended to set the projector to "Idle Mode" in the Setup menu for best Power ON response. NOTE 2: Pins 1, 4, 6, and 9 are used inside the projector. NOTE 3: Jumper "Request to send" and "Clear to Send" together on both ends of the cable to simplify cable connection. NOTE 4: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps. LT220/240/240K/260/260K Control Codes Function POWER ON POWER OFF INPUT SELECT RGB 1 INPUT SELECT RGB 2 INPUT SELECT VIDEO INPUT SELECT S-VIDEO INPUT SELECT VIEWER PICTURE MUTE ON PICTURE MUTE OFF SOUND MUTE ON SOUND MUTE OFF ON SCREEN MUTE ON ON SCREEN MUTE OFF ASPECT RATIO (4:3 Screen) Code Data 02H 00H 02H 01H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 10H 02H 11H 02H 12H 02H 13H 02H 14H 02H 15H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 02H 0FH 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 02H 02H 02H 02H 02H 00H 00H 00H 00H 00H 00H 05H 05H 05H 05H 05H 05H 05H 05H 02H 02H 03H 01H 01H 01H 01H 01H 12H 13H 14H 15H 16H 17H 18H 18H 18H 18H 18H 18H 18H 18H 05H 01H 02H 06H 0BH 1FH 09H 0AH 0EH 13H 27H 4:3 Letterbox Widescreen Crop ASPECT RATIO (16:9 Screen) 4:3 Window Letterbox Widescreen 4:3 Fill AUTO ADJUST 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 18H 00H 01H 02H 03H 00H 01H 02H 04H 00H 00H 00H 00H 00H 00H 00H 00H 30H 31H 32H 33H 30H 31H 32H 34H NOTE: Contact your NEC rep for codes not listed. Cable Connection Communication Protocol Baud Rate: 38400 bps Data Length: 8 bits Parity: No Parity Stop Bit: One bit X on/off: None Communications: Full duplex PC Control Connector (DIN-8P) To RxD of PC 8 5 2 7 4 1 6 3 To GND of PC To TxD of PC NOTE 1: It is recommended to set the projector to "Idle Mode" in the Setup menu for best Power ON response. NOTE 2: Pins 2, 3, 5, 6 and 8 are used inside the projector. NOTE 3: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps. WT600 Control Codes Function POWER ON POWER OFF INPUT SELECT RGB INPUT SELECT DVI (ANALOG) INPUT SELECT DVI (DIGITAL) INPUT SELECT VIDEO INPUT SELECT S-VIDEO INPUT SELECT VIEWER PICTURE MUTE ON PICTURE MUTE OFF SOUND MUTE ON SOUND MUTE OFF ON SCREEN MUTE ON ON SCREEN MUTE OFF ASPECT RATIO (4:3 Screen) 4:3 Letterbox Widescreen Crop ASPECT RATIO (16:9 Screen) 4:3 Window Letterbox Widescreen 4:3 Fill AUTO ADJUST Code Data 02H 00H 02H 01H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 10H 02H 11H 02H 12H 02H 13H 02H 14H 02H 15H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 02H 0FH 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 02H 02H 02H 02H 02H 02H 00H 00H 00H 00H 00H 00H 05H 05H 05H 05H 05H 05H 05H 05H 02H 02H 03H 01H 01H 01H 01H 01H 01H 12H 13H 14H 15H 16H 17H 18H 18H 18H 18H 18H 18H 18H 18H 05H 01H 02H 1AH 06H 0BH 1FH 09H 0AH 22H 0EH 13H 27H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 18H 00H 01H 02H 03H 00H 01H 02H 04H 00H 00H 00H 00H 00H 00H 00H 00H 30H 31H 32H 33H 30H 31H 32H 34H Note: Contact your NEC rep for codes not listed. Cable Connection Communication Protocol: Baud Rate: 38400 bps Data Length: 8 bits Parity: No Parity Stop Bit: One bit X on/off: None Communications: Full duplex PC Control Connector (DIN-8P) To RxD of PC 8 5 7 4 2 1 6 3 \ To GND of PC To TxD of PC NOTE 1: It is recommended to set the projector to "Idle Mode" in the Setup menu for best Power ON response. NOTE 2: Pins 2, 3, 5, 6 and 8 are used inside the projector. NOTE 3: For long cable runs it is recommended to set communication speed in the Setup menu to 9600 bps. VT770 Control Codes Function POWER ON POWER OFF INPUT SELECT COMPUTER 1 INPUT SELECT COMPUTER 2 INPUT SELECT VIDEO INPUT SELECT S-VIDEO INPUT SELECT COMPONENT INPUT SELECT VIEWER PICTURE MUTE ON PICTURE MUTE OFF SOUND MUTE ON SOUND MUTE OFF ON SCREEN MUTE ON ON SCREEN MUTE OFF ASPECT RATIO (4:3 Screen) 4:3 Letterbox Widescreen Crop ASPECT RATIO (16:9 Screen) 4:3 Window Letterbox Widescreen 4:3 Fill AUTO ADJUST Code Data 02H 00H 02H 01H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 10H 02H 11H 02H 12H 02H 13H 02H 14H 02H 15H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 02H 0FH 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 02H 02H 02H 02H 02H 02H 00H 00H 00H 00H 00H 00H 05H 05H 05H 05H 05H 05H 05H 05H 02H 02H 03H 01H 01H 01H 01H 01H 01H 12H 13H 14H 15H 16H 17H 18H 18H 18H 18H 18H 18H 18H 18H 05H 01H 02H 06H 0BH 1AH 1FH 09H 0AH 0EH 13H 22H 27H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 18H 00H 01H 02H 03H 00H 01H 02H 04H 00H 00H 00H 00H 00H 00H 00H 00H 30H 31H 32H 33H 30H 31H 32H 34H Note: Contact your NEC rep for codes not listed. Cable Connection Communication Protocol: Baud Rate: 38400 bps Data Length: 8 bits Parity: No Parity Stop Bit: One bit X on/off: None Communications: Full duplex PC Control Connector (D-Sub 9p) To TxD of PC To RxD of PC To GND of PC 1 2 67 3 8 4 9 5 To RTS of PC To CTS of PC NOTE1: It is recommended to set the projector to "Idle Mode" in the Setup menu for best Power ON response. NOTE2: Pins 1, 4, 6, and 9 are used inside the projector. NOTE3: Jumper "Request to send" and "Clear to Send" together on both ends of the cable to simplify cable connection. NOTE4: For long cable runs it is recommended to set communication speed to 9600 bps in the Setup menu. VT46/465/460/560/660/660K Control Codes Function POWER ON POWER OFF INPUT SELECT RGB INPUT SELECT VIDEO INPUT SELECT S-VIDEO PICTURE MUTE ON PICTURE MUTE OFF SOUND MUTE ON SOUND MUTE OFF Code Data 02H 00H 02H 01H 02H 03H 02H 03H 02H 03H 02H 10H 02H 11H 02H 12H 02H 13H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 02H 02H 02H 00H 00H 00H 00H 02H 03H 01H 01H 01H 12H 13H 14H 15H 01H 06H 0BH 09H 0EH 13H NOTE: Contact your NEC rep for codes not listed. Cable Connection Communication Protocol Baud Rate: 19200 bps Data Length: 8 bits Parity: No Parity Stop Bit: One bit X on/off: None Communications: Full duplex 5 2 PC Control Connector (DIN-8P) To RxD of PC 8 7 4 1 6 3 To GND of PC To TxD of PC NOTE 1: Pins 2, 3, 5, 6 and 8 are used inside the projector. NOTE 2: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps. HT1000/1100 Control Codes FUNCTION POWER ON POWER OFF INPUT SELECT RGB INPUT SELECT COMPONENT INPUT SELECT VIDEO INPUT SELECT S-VIDEO INPUT SELECT DVI (DIGITAL) INPUT SELECT VIEWER PICTURE MUTE ON PICTURE MUTE OFF SOUND MUTE ON SOUND MUTE OFF ON SCREEN MUTE ON ON SCREEN MUTE OFF ASPECT RATIO (16:9 Screen) NORMAL FULL ZOOM STADIUM ASPECT RATIO (4:3 Screen) NORMAL ZOOM CINEMA V-ZOOM AUTO ADJUST CODE DATA 02H 00H 02H 01H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 03H 02H 10H 02H 11H 02H 12H 02H 13H 02H 14H 02H 15H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 03H 10H 02H 0FH 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 02H 02H 02H 02H 02H 02H 00H 00H 00H 00H 00H 00H 05H 05H 05H 05H 05H 05H 05H 05H 02H 02H 03H 01H 01H 01H 01H 01H 01H 12H 13H 14H 15H 16H 17H 18H 18H 18H 18H 18H 18H 18H 18H 05H 01H 10H 06H 0BH 1AH 1FH 09H 18H 0EH 13H 22H 27H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 00H 18H 05H 06H 07H 0AH 05H 07H 08H 09H 00H 00H 00H 00H 00H 00H 00H 00H 35H 36H 37H 3AH 35H 37H 38H 39H Note: Contact your NEC rep for codes not listed. Cable Connection Communication Protocol: Baud Rate: 38400 bps Data Length: 8 bits Parity: No Parity Stop Bit: One bit X on/off: None Communications: Full duplex PC Control Connector (DIN-8P) To RxD of PC 8 5 2 7 4 1 6 3 To GND of PC To TxD of PC NOTE 1: It is recommended to set the projector to "Idle Mode" in the Setup menu for best Power ON response. NOTE 2: Pins 2, 3, 5, 6 and 8 are used inside the projector. NOTE 3: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps.