User manual SEGA VIRTUA STRIKER 4 - SERVICE MANUAL

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: To maintain safety: To ensure the safe operation of this product, be sure to read the following before usage. The following instructions are intended for the users, operators and the personnel in charge of the operation of the product. After carefully reading and sufficiently understanding the warning displays and cautions, handle the product appropriately. Be sure to keep this manual close to the product or in a convenient place for future reference. Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of DANGER, WARNING, CAUTION, etc. are used. Be sure to understand the contents of the displays before reading the text. Indicates that mishandling the product by disregarding this pictograph will cause severe injury or death. Indicates that mishandling the product by disregarding this warning will cause a potentially hazardous situation which can result in death or serious injury. For the safe usage of the product, the following pictographs are used: Indicates "HANDLE WITH CARE." In order to protect the human body and equipment, this display is attached to places where the Owner's Manual, Serviceman Manual and/or Service Manual should be referred to. Indicates a "Protective Earth Terminal." Before operating the equipment, be sure to connect it to the Ground. (The step may be omitted for products in which a power cord with earth is used.) Perform work in accordance with the instructions herein stated. Instructions for work are explained by paying attention to the aspect of accident prevention. Failing to perform work as per the instructions can cause accidents. In the case where only those who have technical expertise should perform the work to avoid hazardous situation, the instructions herein state that the site maintenance personnel should perform such work. Be sure to turn off the power before working on the machine. To prevent an electric shock, be sure to turn off the power before carrying out any work that requires direct contact with the interior of the product. If the work is to be performed in the power-on status, the Instruction Manual herein always states to that effect. Be sure to ground the Earth Terminal. (This is not required in the case where a power cord with earth is used.) This product is equipped with the Earth Terminal. When installing the product, connect the Earth Terminal to the "accurately grounded indoor earth terminal" by using an earth wire. Unless the product is grounded appropriately, the user can be subject to an electric shock. After performing repair, etc. for the control equipment, ensure that the Earth Wire is firmly connected to the control equipment. Ensure that the Power Supply used is equipped with an Earth Leakage Breaker. This product does not incorporate the Earth Leakage Breaker. Using a power supply which is not equipped with the Earth Leakage Breaker can cause a fire when earth leakage occurs. Be sure to use fuses which meet the specified rating. (Only for the machines which use fuses.) Using fuses exceeding the specified rating can cause a fire and an electric shock. Indicates that mishandling the product by disregarding this caution will cause a slight hazardous situation which can result in personal injury and/or material damage. Specification changes (removal of equipment, conversion and addition) not designated by SEGA are not allowed. The parts of the product include warning labels for safety, covers for personal protection, etc. It is very hazardous to operate the product by removing parts and/or modifying the circuits. Should doors, lids and protective parts be damaged or lost, refrain from operating the product, and contact where the product was purchased from or the office herein stated. SEGA shall not be held responsible for any accidents, compensation for damage to a third party, resulting from the specifications not designated by SEGA. Ensure that the product meets the requirements of appropriate Electrical Specifications. Before installing the product, check for Electrical Specifications. SEGA products have a nameplate on which Electrical Specifications are described. Ensure that the product is compatible with the power supply voltage and frequency requirements of the location. Using any Electrical Specifications different from the designated Specifications can cause a fire and an electric shock. Install and operate the product in places where appropriate lighting is available, allowing warning labels to be clearly read. To ensure safety for the customers, labels and printed instructions describing potentially hazardous situations are applied to places where accidents can be caused. Ensure that where the product is operated has sufficient lighting allowing the warnings to be read. If any label is peeled off, apply it again immediately. Please place an order with where the product was purchased from or the office herein stated. When handling the monitor, be very careful. (Applies only to the product with a monitor.) Some of the monitor (TV) parts are subject to high tension voltage. Even after turning off the power, some portions are still subject to high tension voltage sometimes. Monitor repair and replacement should be performed only by those technical personnel who have knowledge of electricity and technical expertise. Be sure to adjust the monitor/projector properly. (Applies only to the product with a monitor/projector.) Do not operate the product leaving on-screen flickering or blurring as it is. Using the product with the monitor/projector not properly adjusted may cause dizziness or a headache to an operator, a player, or the customers. When transporting or reselling this product, be sure to attach this manual to the product. In the case where commercially available monitors and printers are used in this product, only the contents relating to this product are explained herein. Some commercially available equipment has functions and reactions not stated in this manual. Read this manual together with the specific Instruction Manual of such equipment. * Descriptions herein contained may be subject to improvement changes without notice. * The contents described herein are fully prepared with due care. However, should any question arise or errors be found, please contact SEGA. INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before turning on the power, check the following points to ensure that the product has been transported in a satisfactory status. Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet? Are Casters and Adjusters damaged? Do the power supply voltage and frequency requirements meet with those of the location? Are all wiring connectors correctly and securely connected? Unless connected in the correct way, connector connections can not be made accurately. Do not insert connectors forcibly. Do power cords have cuts and dents? Do the fuses used meet specified ratings? Is the Circuit Protector in an energized status? Are all accessories available? Can all Doors and Lids be opened with the Accessory Keys? Can Doors and Lids be firmly closed? TABLE OF CONTENTS E1-0504 420-6843-01 Use of this product is unlikely to cause physical injuries or damage to property. However, points that require special attention are indicated by thick underlining, the word "IMPORTANT" and the symbol below. Indicates important information that, if ignored, may result in the mishandling of the product and cause faulty operation or damage to the product. 1. HANDLING PRECAUTIONS Note: The contents herein described are subject to change without notice. 2. SPECIFICATIONS 3. TURNING THE POWER ON WARNING BOOT/FIRM VERSION DOES NOT FULFILL THE GAME SPEC. PLEASE ENTER GAME TEST AND UPDATE. VIRTUA STRIKER 4 TEST MENU INPUT TEST GAME ASSIGNMENTS CALIBRATION CARD TEST CLOSE SETTING SYSTEM UPDATE BOOKKEEPING BACKUP DATA CLEAR -> EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON SYSTEM UPDATE MENU UPDATE BOOT PROGRAM CURRENT VERSION: 1.03 LATEST VERSION: 2.17 PRESS TEST BUTTON TO START SYSTEM UPDATE MENU UPDATE BOOT PROGRAM... CURRENT VERSION: 1.03 LATEST VERSION: 2.17 PROGRESS: 68% DO NOT TURN OFF THE POWER SYSTEM UPDATE MENU COMPLETE PLEASE REBOOT CALIBRATION P1 P2 UP 87 90 DOWN 88 91 LEFT 83 7F RIGHT 83 80 Please carry out adjustment of levers. Make sure that you set up CALIBRATION on a lever for both "PLAYER 2" and "PLAYER 1". Please press Start Button, if adjustment finishes. 4. GAME DESCRIPTION * If the EVENT MODE setting in Test Mode is set to ON, both players get GAME OVER at the end of the first match regardless of who wins and loses. * The promotion match/relegation match mark is shown on the right side of "NAME (User Name)" that is displayed on the VERSUS screen. The mark is also shown during the match. * The competition match mark is displayed below the [Stadium Introduction Map] on the VERSUS screen before the match. * If the card usage setting is set to OFF using Test Mode, the card icons are not displayed at all. In this case, cards cannot be used. * The FORMATION and TACTICS that have been assigned to a TACTICS BUTTON can be used during a match. * Other players cannot join the game while entering the user name. * If the player finishes without entering a single character or after entering forbidden characters, the pre-defined default user name will be entered automatically. * Other players cannot join the game while a player is changing settings on the TEAM MANAGEMENT screen. * You can cancel the player selected using the red DASH BUTTON. * You can also register suspended players as members of the STARTERS group. However, the player is temporarily substituted on the SUSPENSION screen before the match. * Note that even if you restore the default values, this will not erase the players, tactics and stadiums that you have acquired up to now. * The windows are divided into several tiers, and the setting won't be changed unless the items are selected all the way to the deepest window. (Example) MAIN FORMATION 4BACKS 4-3-2-1 LINE (Changes the setting.) * Note that even if you restore the default values, this will not erase the players, tactics and stadiums that you have acquired up to now. * Although the final regional qualifiers are matches that determine which country will represent each continent, depending on the conditions this may be a playoff between teams from different continents. * FORMATIONS and TACTICS that have been assigned to TACTICS BUTTONS can be used during the game. * Any warning cards received during a game are accumulated at the end of the match. Any players who have accumulated more than a fixed number of warning cards will be subject to suspension for 1 or 2 matches. Once the number of matches that the suspension corresponds to is over, the accumulated cards are cleared and the player can play in the next match. * A match against the COM where another player joins midway through does not count as one match. * You can skip to the start of the second half by pressing any button other than the Start Button. * You can cancel a selection using the red button. * You cannot select players that were sent off during the first half or players that are under suspension. * If the card is only half-inserted into the card reader/writer, the machine won't detect the card and the game will continue as if a card is not being used. * If you insert the card on the SELECT TEAM screen on the second or subsequent time you play, the team will be selected automatically. * Card renewal can be performed even for cards that have not been fully used up. 5. TEST MODE SYSTEM MENU RAM TEST MEDIA BOARD TEST SYSTEM INFORMATION JVS TEST SOUND TEST C.R.T. TEST ............................ COIN ASSIGNMENTS ....................... CLOCK SETTING .......................... NETWORK SETTING ........................ ENTER GAME TEST [*******************] EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON a) b) c) d) VIRTUA STRIKER 4 TEST MENU INPUT TEST GAME ASSIGNMENTS CALIBRATION CARD TEST CLOSE SETTING SYSTEM UPDATE BOOKKEEPING BACKUP DATA CLEAR -> EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON INPUT TEST P1 P2 ANALOG X 80 80 ANALOG Y 80 80 DASH OFF OFF SHORT PASS OFF OFF LONG PASS OFF OFF SHOOT OFF OFF TACTICS(U) OFF OFF TACTICS(M) OFF OFF TACTICS(D) OFF OFF START OFF OFF SERVICE OFF TEST OFF PRESS TEST AND SERVICE BUTTON TO EXIT GAME ASSIGNMENTS (1/2) ADVERTISE SOUND ON EVENT MODE OFF CARD R/W P1 USE ON CARD R/W P2 USE ON -> NEXT Please disregard option screen for "CARD R/W USE" setup if the Machine has NO CARD R/W device. SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON * Be aware that on cabinets that are not fitted with a card R/W, changing the CARD R/W P1 (P2) USE setting has no effect. GAME ASSIGNMENTS (2/2) GAME DIFFICULTY NORMAL VIRTUAL TIME REAL TIME SET(COM) 1'30" TIME SET(VS) 1'30" G-GOAL TIME(COM) OFF G-GOAL TIME(VS) OFF PK SYSTEM (COM) OFF PK SYSTEM (VS) OFF SET DEFAULT -> EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON * The number of PK setting (ON [REAL PK] continues until a winner is determined. However, "MAX99" is displayed). * The number of PK setting (ON [REAL PK] continues until a winner is determined. However, "MAX99" is displayed). * Be careful because the CLOSE SETTING also returns to the default value if you execute SET DEFAULT. CALIBRATION P1 P2 UP 40 40 DOWN C0 C0 LEFT 4040 RIGHT C0 C0 Make sure that you set up CALIBRATION on a lever for both "PLAYER 2" and "PLAYER 1". PRESS TEST BUTTON TO EXIT * If the CARD R/W 1P (2P) USE setting on the GAME ASSIGNMENTS screen is set to "OUT OF SERVICE" or "OFF", the operation of the card reader/writer cannot be tested. CARD TEST CARD P1: SW OFF : LOCK OFF : INSERT CARD READ/WRITE TEST LOCK ON/OFF CARD P2: SW OFF : LOCK OFF : INSERT CARD READ/WRITE TEST LOCK ON/OFF -> EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON * If a card R/W has not been installed on one of the P1 or P2 sides, or an initialization error occurred in one of the card R/W, the CARD TEST display for that side will be cleared. * If a card R/W has not been installed on both of the P1 and P2 sides, or an initialization error occurred in both of the card R/Ws, the message "CARD R/W NOT FOUND." is displayed. You cannot run the card test, so you should select EXIT and skip this screen. CLOSE SETTING SCHEDULE TYPE OFF -> EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON CLOSE SETTING SCHEDULE TYPE EVERY DAY CLOSE 23:45 -> EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON CLOSE SETTING SCHEDULE TYPE WEEK CLOSE SUN 24:45 MON 23:45 TUE 23:45 WED 23:45 THU 23:45 FRI 24:45 SAT 24:45 -> EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON SYSTEM UPDATE MENU ALL PROGRAMS ARE UP TO DATE PRESS TEST BUTTON TO EXIT BOOKKEEPING (1/5) [ CREDIT DATA ] COIN 1 0 COIN 2 0 COIN 3 0 COIN 4 0 TOTAL COIN 0 COIN CREDIT 0 SERVICE CREDIT 0 TOTAL CREDIT 0 PRESS TEST BUTTON TO CONTINUE BOOKKEEPING (2/5) [ GLOBAL DATA ] NUMBER OF GAMES 0 P1 ALL CARD PLAY 0 P2 ALL CARD PLAY 0 NEW CARD PLAY 0 PULLING CARD OUT 0 CARDPLAYER 0.0% TOTAL TIME 0d 0h 0m 0s TOTAL PLAY TIME 0d 0h 0m 0s 1P PLAY TIME 0d 0h 0m 0s VS PLAY TIME 0d 0h 0m 0s PLAY TIME RATE 0.0% 1P PLAY RATE 0.0% VS PLAY RATE 0.0% AVERAGE PLAY TIME 0d 0h 0m 0s LONGEST PLAY TIME 0d 0h 0m 0s SHORTEST PLAY TIME 0d 0h 0m 0s PRESS TEST BUTTON TO CONTINUE BOOKKEEPING (3/5) [ TIME HISTOGRAM ] 3'59" 0 4'00" 4'59" 0 5'00" 5'59" 0 6'00" 6'59" 0 7'00" 7'59" 0 8'00" 8'59" 0 9'00" 9'59" 0 10'00"10'59" 0 11'00"11'59" 0 12'00"12'59" 0 13'00"13'59" 0 14'00"14'59" 0 15'00"15'59" 0 16'00"16'59" 0 17'00"17'59" 0 18'00"18'59" 0 19'00"19'59" 0 20'00" 0 PRESS TEST BUTTON TO CONTINUE BOOKKEEPING (4/5) [ TOTAL GAME DATA ] TOTAL GAME COUNT 0 PLAYER1 GAME COUNT 0 PLAYER2 GAME COUNT 0 [COM GAME DATA] COM GAME COUNT 0 WIN 0 DRAW 0 LOSE 0 CONTINUE 0 [ TOURNAMENT REPORT ] QUALIFY FOR(PLAY-OFF) 0 FIRST ROUND 0 QUARTER FINALS 0 SEMI FINALS 0 FINAL 0 FINAL WINNER 0 PRESS TEST BUTTON TO CONTINUE BOOKKEEPING (5/5) [ VS GAME DATA ] VS GAME COUNT 0 WIN 0 DRAW 0 VS WINNING STREAK 0 VS SPECIAL COUNT 0 SPECIAL MATCH COUNT 0 AVERAGE 0.0% [ VS WINNING HISTOGRAM ] WINS COUNT WINS COUNT 1 0 10-14 0 2 0 15-19 0 3 0 20-24 0 4 0 25-29 0 5 0 30-39 0 6 0 40-49 0 7 0 50- 0 8 0 9 0 PRESS TEST BUTTON TO EXIT BACKUP DATA CLEAR YES(CLEAR) -> NO (CANCEL) SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON