Start Here EasyShare 5300 EasyShare 5300 All-in-One Printer All-in-One Printer Print Copy Scan Rotate Zoom Proofsheet Transfer Photo Scan Copy Menu Help Color Ink Cartridge 10 Black Ink Cartridge Cancel Start On/Off 10 Attention Note: A USB 2.0 cable is required to connect your Kodak All-in-One Printer to your Windows or Macintosh OS computer. Identify Main Components 1. 2. Ea EasyShare 5300 11. All-in-One Printer 12. Easyshare 4. 5. 6. 7. 8. 9. 14. 15. 1. Scanner glass 2. Printer access door 3. Output tray 4. Paper-width guide 5. Main tray 6. Photo tray 7. Paper-length guide 8. Photo tray light 9. USB drive/PictBridge port 10. Memory card light 11. Memory card slots 12. Control panel 13. USB port 14. Power connector 15. Rear access door 16. Scanner lid 2 www.kodak.com/go/aiosupport All-in-One Printer 5300 3. 10. 16. 13. 1 Unpack Printer and Install Control Panel IMPORTANT: Do not connect the USB cable to the printer until instructed during software installation. a) See box flaps for unpacking instructions. Remove all orange shipping tape from the printer. b) If not preinstalled, insert the control panel overlay, bottom end first. OK E EasyShare 5300 All-in-One Printer OK EasyShare 5300 All-in-One Printer c) Press down on all edges of the overlay until it snaps into position. Transfer Rotate Zoom Proofsheet Photo Scan Copy Menu Help OK Cancel On/Off Attention www.kodak.com/go/aiosupport 3 2 Load Paper a) Load photo paper into the photo tray. Lift the photo tray lid until it remains standing without support. Insert the photo paper glossy side down. IMPORTANT: Do not overload the photo tray. Max 20 sheets. b) Push the photo tray in until it clicks into place. NOTE: You can only print to the photo tray when the photo tray is pushed in. Lower the photo tray lid. c) Load plain white paper into the main tray. 4 www.kodak.com/go/aiosupport 3 Install Printhead IMPORTANT: The printhead is fragile. Handle carefully. a) Lift the printer access door. Make sure the orange tape is removed from the carriage. b) Remove the printhead from its bag. IMPORTANT: Insert the printhead immediately upon opening sealed bag. c) Pull on the orange tab to remove the protective retainer. www.kodak.com/go/aiosupport 5 Install Printhead d) Carefully remove and discard the black plastic shield and the orange protective cap. IMPORTANT: Do not touch the copper-colored contacts. e) Place the printhead into the carriage. Insert at the angle shown. f) Push firmly against the back wall of the printhead until it clicks into place. Tip: The printhead requires a firm push and makes an audible click when locked into place. 6 www.kodak.com/go/aiosupport 4 Install Ink Cartridges a) Remove the black ink cartridge from its bag. IMPORTANT: Insert ink cartridges immediately upon opening sealed bag. 10 Black Ink Cartridge b) Carefully remove and discard the orange cap. Handle ink cartridges carefully to avoid ink transfer. 10 B la ck In k C a rtr id e g c) Insert the black ink cartridge into the printhead. Black Ink Cartridge 10 www.kodak.com/go/aiosupport 7 Install Ink Cartridges d) Press down on the ink cartridge until you hear it click into position. Blac k In k Ca rtri dge 10 10 10 C a r t r id g e 10 C o lo r e) Open and uncap the color ink cartridge. Insert it into the printhead. In k 10 C olo r In k C ar tr id ge Bla ck In k Ca rid rt ge 10 ck Bla k In rt Ca ge rid f) Press down firmly on the ink cartridge until you hear it click into position. It is normal for the printhead to flex when inserting the cartridge. You will not damage the printer. Close the printer access door. 8 www.kodak.com/go/aiosupport 5 Connect Power a) Connect the power supply and adapter. All-in-One Printer EasyShare 5300 All-in-One Printer Easyshare 5300 b) Remove the plastic film from the LCD display. Position the LCD display and press ON. EasyShare 5300 All-in-One Printer c) Press ON. If prompted, select your language. Use the key to select a region. -ON www.kodak.com/go/aiosupport 9 6 Calibrate Printer IMPORTANT: Make sure that the photo tray is pushed in. The photo tray light should be lit. a) Press Start. Wait two minutes for the calibration sheet to print. Tip: If the calibration sheet does not print properly, see the Troubleshooting section in this setup guide. b) Remove the calibration sheet from the output tray. Place it face down and align to the front, right corner of the scanner glass, as shown. IMPORTANT: The blue arrow in the corner of the calibration sheet must point to the registration marks as shown. 4x6 4x6 c) Lower the scanner lid and press Start. Remove the sheet from the scanner glass when the calibration is complete. 4x6 d) Lift the photo tray lid, then slide the photo tray toward you to return to main tray operation. The photo tray light will turn off. 10 www.kodak.com/go/aiosupport 7 Install Software WINDOWSWINDOWS WINDOWSWINDOWS WINDOWSWINDOWS WINDOWSWINDOWS WINDOWSWINDOWS WINDOWSWINDOWS WINDOWSWINDOWS WINDOWSWINDOWS WINDOWSWINDOWS WINDOWSWINDOWS WINDOWSWINDOWS MACINTOSHMACINTOSH MACINTOSHMACINTOSH MACINTOSHMACINTOSH MACINTOSHMACINTOSH MACINTOSHMACINTOSH MACINTOSHMACINTOSH MACINTOSHMACINTOSH MACINTOSHMACINTOSH MACINTOSHMACINTOSH MACINTOSHMACINTOSH MACINTOSHMACINTOSH WINDOWS IMPORTANT: Do not connect the USB cable to the printer until instructed during software installation. a) Load the Kodak AiO Printer Software CD into the CD-ROM drive. Follow the on-screen prompts when the instructions appear. If instructions do not appear, click Start, then Run. Select CD-ROM drive and type setup.exe, then press ENTER. b) Connect the USB cable to the printer when instructed. Continue to follow the on-screen prompts until installation is complete. MACINTOSH a) Connect the USB cable to the printer and your Macintosh computer. b) Load the Kodak AiO Printer Software CD into the CD-ROM drive. The Kodak AiO Printer Software installer window should be displayed. If not, double-click the Kodak AiO Printer Software CD icon on the desktop. Follow the on-screen prompts until installation is complete. www.kodak.com/go/aiosupport 11 8 Helpful Tips and Getting Started Pull out the output tray extender to help collect your prints. The photo tray light illuminates when the photo tray is pushed in. To use the main paper tray, disengage the photo tray by pulling it towards you You can access and use the AiO Home Center by double-clicking on the icon on your desktop. You can use Kodak Home Center to browse, print, copy, scan, and configure your AiO Printer from the computer. Kodak Home Center Software You can use Kodak EasyShare to transfer, view, and work with your digital pictures and videos, if installed. EasyShare Software 12 www.kodak.com/go/aiosupport Control Panel Features Display photos, messages, status, and menus. EasyShare 5300 Displays the Proofsheet menu when there are pictures on an inserted memory card or connected USB host device. Rotates the picture on the display. Rotate All-in-One Printer Zoom Proofsheet Transfer Photo Zooms in or out in .05X increments. Scan Copy Transfers images from a device connected to a USB host port, PictBridge, or (PTP) PictureTransfer Protocol. Menu Help OK Displays the Main menu on the LCD screen. Cancel On/Off Displays the Help menu on the LCD screen. Attention Indicates attention is needed. When illuminated, see LCD screen for further instruction. www.kodak.com/go/aiosupport 13 Troubleshooting If you have additional questions about troubleshooting this device, please visit www.kodak.com/go/5300aiosupport PROBLEM: I cannot get a calibration sheet to print. SOLUTION: When necessary, you can force a calibration sheet to print by following these steps: 1. Press Menu, select Calibrate Printer and press OK. 2. Select Print Calibration Page and press OK. 3. When the print comes out, place it at the front, right corner of the scanner glass. 4. Close the scanner lid and press START. PROBLEM: My calibration page printed on plain white text paper. SOLUTION: Follow the directions as listed in steps 3-4. Calibration will work successfully on both plain white paper and photo paper. PROBLEM: I cannot print to my desired paper type. SOLUTION: Check to see if the photo tray is pushed in. You can do this by checking if the green photo tray light is illuminated. If it is, all prints will be produced from this tray. If you want to print from the main tray, pull out the photo tray by lifting the photo tray lid and sliding the paper tray toward you. PROBLEM: I have a paper jam. SOLUTION: 1. Press in the tabs on the rear access door to remove the door. 2. Gently pull the paper out of the rollers. IMPORTANT: If the paper tears while removing it, check inside the printer for torn pieces of paper and remove them. Additional jams are likely to occur if all of the torn pieces are not removed. 3. Replace the rear access door. Gently push the door forward until it snaps into place. Is Further Troubleshooting Required? If you need further information to help answer your questions, please contact Technical Support and have your KSN number ready. Your KSN number can be found on the printer by lifting the printer access door as shown. KODAK SERVICE NUMBER *F330065* *F330065* F330065 14 www.kodak.com/go/aiosupport More Accessories More Options More Convenience Wireless 2.0 USB Bluetoot h Adapter The KODAK EasyShare All-in-One Printer gives you more. Be sure to visit our online store to select from our full line of supplies and accessories at www.kodak.com/go/AiO Kodak's Inkjet Photo Paper Get prints that look great the first time with Kodak's unique backprint technology that automatically enables optimized prints. Value Packs Save up to 50% on everything you print and pay as low as 10 cents a print with our ink and paper Value Packs. Two-sided Printing Accessory It's easy to print both sides of your document with the Kodak EasyShare 5000 Series Two-Sided Printing Accessory. Wireless Adaptor Go wireless with the Kodak Wireless 2.0 USB Bluetooth Adaptor. Note: A USB 2.0 cable is required to connect your Kodak All-in-One Printer to your Windows or Macintosh OS computer. Available in the Kodak online store or see your local retailer. www.kodak.com/go/aiosupport 15 Safety - Read and follow these instructions before using KODAK products. - Always follow basic safety procedures. - Follow all warnings and instructions marked on the equipment. WARNING STATEMENTS - Do not expose this product to liquid, moisture, or extreme temperatures. KODAK AC adapters are intended for indoor use only. The use of controls, adjustments, or procedures other than those specified herein may result in exposure to shock and/or electrical or mechanical hazards. - Keep ink cartridges out of reach of children. Ink may be harmful if swallowed. - Do not place your AiO Printer on an unstable cart, stand, bracket, or table. Injury to persons and damage to the equipment may occur. - The use of an accessory attachment that is not recommended by Kodak, such as an AC adapter, may cause fire, electric shock, or injury. - Pushing objects through the equipment openings can result in an electric shock or risk of fire. CAUTIONARY STATEMENTS - Adjust only those controls covered in the operating instructions. - Do not disassemble this product; there are no user-serviceable parts inside. Refer servicing to qualified service personnel. - The AC adapter power supply is equipped with 3-wire grounding type plugs. If you cannot insert the plug into the power outlet, contact an electrician to check or replace the power outlet. - Do not plug the AC adapter into a household extension cord. - If the power cord or plug is frayed or damaged, the equipment gets wet, or the equipment does not operate normally when the operating instructions are followed, unplug your AiO Printer from the power outlet and contact Kodak qualified service personnel for further instructions. - For added protection from damage during a lightning storm, or any time when your AiO Printer and it's associated AC adapter will be left unused for long periods of time, unplug the AC adapter from the power outlet and any attached fax line from the printer. - To reduce the risk of fire, use only 26 AWG or larger telecommunication line cord. - To prevent your AiO printer from overheating do not place it near a heat register, or install it in a cabinet without proper ventilation. - Do not use your AiO Printer near water or spill liquid on it. - Unplug the equipment from the wall outlet before cleaning. - Dropping your AiO Printer may damage the housing and result in extensive damage that will require repair by a qualified technician to restore normal operation. - Excessive dust levels may damage internal parts. For more information, go to www.kodak.com/go/MSDS 16 www.kodak.com/go/aiosupport Limited Warranty Limited Warranty Ko ...