User manual KODAK 5300 ALL-IN-ONE PRINTER - SETUP POSTER

Start here EasyShare 5300 All-in-One Printer Print Copy Scan EasyShare 5300 All-in-One Printer Unpack printer IMPORTANT: Do not connect the USB cable to the printer until instructed during software installation. 3 Install printhead IMPORTANT: The printhead is fragile. Handle carefully. 4 Install ink cartridges 5 Connect power a) Remove the black ink cartridge from its bag. Black ink cartridge a) Connect the power supply and adaptor. 10 b) Remove all orange shipping tape from the printer. 1 Install control panel OK b) Remove the printhead from its bag. a) If not pre-installed, insert the control panel overlay, bottom end first. b) Carefully remove and discard the orange cap. Handle ink cartridges carefully to avoid ink transfer. 10 b) Remove the plastic film from the LCD display. Position the LCD display and press ON. EasyShare 5300 All-in-One Printer IMPORTANT: Insert the printhead immediately upon opening sealed bag. OK Box contents Rotate Zoom Proofsheet Transfer Photo Scan Copy Menu Help Cancel Start On/Off Attention b) Press down on all edges of the overlay until it snaps into position. Sample paper packs Printhead EasyShare 5300 c) Pull on the orange tab to remove the protective retainer. Transfer c) Insert the black ink cartridge into the printhead. 6 Black ink cartridge Calibrate printer IMPORTANT: Make sure that the photo tray is pushed in. The photo tray light should be lit. All-in-One Printer Rotate Zoom Proofsheet Photo Scan Copy Menu Help OK Cancel On/Off Control panel overlay (may be pre-installed) Attention PU LL 10 a) Press Start. Wait two minutes for the calibration sheet to print. Colour ink cartridg e 10 2 Power supply and adaptor Software CD and brochure Load paper 10 d) Press down on the ink cartridge until you hear it click into position. Blac k ink cartr idge Black and colour ink cartridges 1) Lift the photo tray lid. Insert the photo paper glossy side down. IMPORTANT: Do not overload the photo tray. Max 20 sheets. d) Carefully remove and discard the clear plastic shield and the orange protective cap. 10 a) Load photo paper into the photo tray. 10 Tip: If the calibration sheet does not print properly, see the Troubleshooting section in this set-up poster. IMPORTANT: Do not touch the copper-coloured contacts. b) Remove the calibration sheet from the output tray. Place it face down and align to the front, right corner of the scanner glass, as shown. e) Open and uncap the colour ink cartridge. Insert it into the printhead. Identify main components 2) Push the photo tray in until it clicks into place. Scanner glass Printer access door EasyShare 5300 10 c a rt ri d g e 10 C o lo u r in k Memory card slots All-in-One Printer NOTE: You can only print to the photo tray when the photo tray is pushed in. e) Place the printhead into the carriage. Insert at the angle shown. IMPORTANT: The blue arrow in the corner of the calibration sheet must point to the registration marks as shown. Output tray Paper-width guide Main tray Photo tray Memory card light USB drive/ PictBridge port 3) Lower the photo tray lid. f) Press down firmly on the ink cartridge until you hear it click into position. 10 C olo ur Photo tray light Paper-length guide b) Load plain white paper into the main tray. 10 in k ca rt ri dg e c) Lower the scanner lid and press Start. The ON/OFF light will turn solid green when the calibration is complete. Remove the sheet from the scanner glass. Control panel 1) Scanner lid Rear access door All-in-One Printer 2) f) Push firmly against the top of the white label on the printhead until it clicks into place. It is normal for the printhead to flex when inserting the cartridge. You will not damage the printer. d) Lift the photo tray lid, then slide the photo tray towards you to return to main tray operation. The photo tray light will turn off. g) Close the printer access door. Power connector *1K1194* *1K1194* 1K1198 7 Install Windows Software IMPORTANT: Do not connect the USB cable to the printer until instructed during software installation. a) Load the Kodak EasyShare CD into the CD-ROM drive. If instructions do not appear, click Start, then Run. Select CD-ROM drive and type setup.exe, then press ENTER. b) If connected to the Internet, select Web Install to get the latest upgrades for your printer. c) Follow the on screen prompts to install the AiO software. d) Connect the printer to the USB port. Click Next and follow the on screen prompts. If prompted, re-boot your computer. e) When the EasyShare AiO dialog box appears, close the window. Vista EasyShare 5300 USB port Tip: The printhead requires a firm push and makes an audible click when locked into place. 3) 4) *E* *E* E Install Macintosh software Helpful tips Pull out the output tray extender to help collect your 216 x 297 mm (8.5 x 11.7") prints. Troubleshooting If you have additional questions about troubleshooting this device, please visit www.kodak.com/go/5300aiosupport PROBLEM: I cannot get a calibration sheet to print. SOLUTION: Where necessary, you can force a calibration sheet to print by following these steps: More accessories More options More convenience The KODAK EasyShare All-in-One Printer gives you more. Be sure to visit our online store to select from our full line of supplies and accessories at www.kodak.com/go/AiO. a) Connect the USB cable to the printer and your computer. The photo tray light illuminates when the photo tray is pushed in. To use the main paper tray, disengage the photo tray by pulling it towards you. 1. Press Menu, select Calibrate Printer and press OK. 2. Select Print Calibration Page and press OK. 3. When the print comes out, place it at the front, right corner of the scanner glass. Kodak's inkjet photo paper 4. Close the scanner lid and press START. PROBLEM: I cannot print to my desired paper type. Get prints that look great the first time with Kodak's unique backprint technology that automatically enables optimised prints. Control panel features b) Download the EasyShare AiO software from www.kodak.com/go/5300aiosupport. EasyShare 5300 Displays photos, messages, status and menus Rotates the picture on the display Zooms in or out in .05X increments SOLUTION: Check to see if the photo tray is pushed in. You can do this by checking if the green photo tray light is illuminated. If it is, all prints will be produced from this tray. If you want to print from the main tray, pull out the photo tray by lifting the photo tray lid and sliding the paper tray towards you (see step 6d). PROBLEM: I have a paper jam. SOLUTION: 1. Press in the tabs on the rear access door to remove the door. 2. Gently pull the paper out of the rollers. IMPORTANT: If the paper tears while removing it, check inside the printer for torn pieces of paper and remove them. Additional jams are likely to occur if all of the torn pieces are not removed. 3. Replace the rear access door. Gently push the door forwards until it snaps into place. Value packs Save up to 50% on everything you print and pay as little as 7p per print with our ink and paper value packs. c) Double-click the .dmg file to open it. All-in-One Printer Rotate Zoom Proofsheet Transfer Transfers images from a device connected to a USB host port, PictBridge or Picture Transfer Protocol (PTP) Two-sided printing accessory It's easy to print both sides of your document with the Kodak EasyShare 5000 Series two-sided printing accessory. Photo Scan Copy Menu Help Displays the proofsheet menu when there are pictures on an inserted memory card or connected USB host device Is further troubleshooting required? If you need further information to help answer your questions, please contact Technical Support and have your KSN number ready. Your KSN number can be found on the unit after lifting the printer access door as shown. OK Wireless adaptor Go wireless with the Kodak wireless 2.0 USB Bluetooth adaptor. Wireless 2.0 USB Bluetoot h adaptor Cancel On/Off Displays the Help menu on the LCD screen Attention d) Wait for the Kodak EasyShare Installer icon to appear on your desktop and double-click on it. Displays the Main menu on the LCD screen KODAK SERVICE NUMBER F330065 Indicates attention is needed. When illuminated, see LCD screen for further instruction *F330065* *F330065* Getting started You can access and use the AiO Home Centre by double-clicking on the icon on your desktop. Note: A USB 2.0 cable is required to connect your Kodak All-in-One printer to your Windows or Macintosh OS computer. Available in the Kodak online store or see your local retailer. Windows XP e) Click on the Install Software.app icon and follow the on-screen prompts. The AiO Home Centre will enable you to copy, scan and configure your AiO printer from the computer. You can also launch Kodak EasyShare software for transferring, viewing and working with your digital pictures and videos. Macintosh The AiO Home Centre will enable you to configure your AiO printer from the computer. You can also order supplies and launch Kodak EasyShare software for transferring, viewing and working with your digital pictures and videos. Use the Kodak EasyShare AiO drivers to print and scan to your AiO printer. Need more help? Look here for answers: www.kodak.com/go/5300aiosupport User guide The User Guide is installed with your Kodak AiO software and is located: Windows Start All Programs Kodak Macintosh Library Documentation Kodak AiO Printers Eastman Kodak Company Rochester, NY 14650 U.S.A. © Eastman Kodak Company, 2007 MC/MR/TM: Kodak, EasyShare. The Bluetooth® trade marks are owned by the Bluetooth SIG, Inc. Printed in the U.S.A. Windows® is a registered trade mark of Microsoft Corporation Macintosh® is a registered trade mark of Apple Computer, Inc. EasyShare 5300 a) Lift the printer access door. Make sure the orange tape is removed from the carriage. IMPORTANT: Insert ink cartridges immediately upon opening sealed bag. All-in-One Printer a) See box flaps for unpacking instructions. B la ck in k rt ca ri d e g EasyShare 5300 All-in-One Printer Black ink cartridge 4x6 Bla ck k in ge rid rt ca 4x6 4x6 Bla ck k in ca rt rid ge