User manual FUJITSU C2330 - SOFTWARE GUIDE

Fujitsu LifeBook C Series BIOS Guide LifeBook C Series Model: C2330 Document Date: 11/02/2004 Document Part Number: FPC58-1263-01 FUJITSU COMPUTER SYSTEMS LifeBook C Series Notebook BIOS C Series BIOS BIOS SETUP UTILITY The BIOS Setup Utility is a program that sets up the operating environment for your notebook. Your BIOS is set at the factory for normal operating conditions, therefore there is no need to set or change the BIOS environment to operate your notebook. The BIOS Setup Utility configures: · Device control feature parameters, such as changing I/O addresses and boot devices. · System Data Security feature parameters, such as passwords. n n Selecting a field causes a help message about that field to be displayed on the right-hand side of the screen. Pressing the Enter key with the highlight on a selection that is not a submenu or auto selection will cause a list of all options for that item to be displayed. Pressing the Enter key again will select the highlighted choice. Entering the BIOS Setup Utility To enter the BIOS Setup Utility do the following: 1. Turn on or restart your notebook. 2. Press the [F2] key once the Fujitsu logo appears on the screen. This will open the main menu of the BIOS Setup Utility with the current settings displayed. 3. Press the right and left arrow keys to scroll through the other setup menus to review or alter the current settings. 7. Pressing the [F9] key resets all items in the BIOS to the default values. 8. Pressing the [F10] key saves the current configuration and exits the BIOS Setup Utility. You will be asked to verify this selection before it is executed. 9. Pressing the [F1] key gives you a general help screen. Entering the Setup Utility after a configuration change or system failure If there has been a change in the system configuration that does not match the parameter settings stored in your BIOS memory, or there is a failure in the system, the system beeps and/or displays an error message after the Power On Self Test (POST). If the failure is not too severe, you will have an opportunity to modify the settings of the utility, as described in the following steps: 1. When you turn on or restart the computer there is a beep and/or the following message appears: Error message - please run SETUP program Press key to continue, to run SETUP 2. If an error message is displayed on the screen, and you want to continue with the boot process and start the operating system anyway, press the [F1] key. · If your notebook emits a series of beeps that sounds like a code and the display is blank, please refer to the Troubleshooting Section of your system User's Guide. The Troubleshooting Section includes a list of error messages and their meanings. · If your data security settings require it, you may be asked for a password before the operating system will be loaded. Navigating through the Setup Utility The BIOS setup utility consists of six menus: Main, Advanced, Security, Boot, Info, and Exit. This document explains each menu in turn, including all submenus and setup items. The following procedures allow you to navigate the setup utility menus: 1. To select a menu, use the cursor keys: [ ], [ ]. 2. To select a field within a menu or a submenu, use the cursor keys: [ ], [ ]. 3. To select the different values for each field, press the [Spacebar] or [+] to change to the next higher selection and [F5] or [-] to go to the next lower selection. 4. To activate a submenu press [Enter]. 5. To return to a menu from a submenu, press [Esc]. 6. To go to the Exit menu from any other menu, press [Esc]. 2 C Series BIOS 3. If an error message is displayed on the screen, and you want to enter the setup utility, press the [F2] key. 4. When the setup utility starts with a fault present, the system displays the following message: Warning! Error message [Continue] 5. Press any key to enter the setup utility. The system will then display the Main Menu with current parameters values. 3 LifeBook C Series Notebook BIOS MAIN MENU ­ SETTING STANDARD SYSTEM PARAMETERS The Main Menu allows you to set or view the current system parameters. Follow the instructions for Navigating Through The Setup Utility to make any changes. The following tables show the names of the menu fields for the Main menu and its submenus, all of the options for each field, the default settings and a description of the field's function and any special information needed to help understand the field's use. PhoenixBIOS Setup Utility Security Boot Info *Note that actual drive labels shown may vary. System Time and System Date can also be set from your operating system without using the setup utility. Use the Date and Time icon on your Windows Control panel or double-click on the time in the system tray at the bottom right of the screen. Main Advanced Exit Item Specific Help System Time: System Date: Floppy Disk A: [02:34:56] [11/02/2004] [1.44/1.2 MB, 3.5"] [FUJITSU MHT2040AT-(PM)] [MATSHITADVD-RAM UJ-830S-(SM)] [English (US)] Adjust calendar clock. , , or selects field. Primary Master Secondary Master Language: F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu Figure 1. Main Menu F9 Setup Defaults F10 Save and Exit Table 1: Fields, Options and Defaults for the Main Menu Note that the parameters listed below may differ, as determined by your system configuration. Menu Field System Time: Options ­-- Default ­-- Description Sets and displays the current time. Time is in a 24 hour format of hours:minutes:seconds with 2 digits for each. (HH:MM:SS). Example: 16:45:57. You may change each segment of the time separately. Move between the segments with the [Tab] key and/or [Shift] + [Tab] keys. 4 Main Menu Table 1: Fields, Options and Defaults for the Main Menu Note that the parameters listed below may differ, as determined by your system configuration. Menu Field System Date: Options ­-- Default ­-- Description Sets and displays the current date. Date is in a month/ day/year numeric format with 2 digits each for month and day and 4 digits for year. (MM/DD/YYYY) for example: 10/16/2001. You may change each segment of the date separately. Move between the segments with the [Tab] key and/or [Shift] + [Tab] keys. Enables or disables a floppy disk drive. Floppy Disk A: Primary Master: · Disabled · [1.44/1.2 MB 3.5"] Selects Primary Master submenu [1.44/1.2 MB 3.5"] The product # of the Hard Drive Display the type of device on this ATA/ATAPI interface, if there is one. Pressing the Enter key selects the Primary Master submenu allowing additional device configuration options for this interface. Display the type of device on this ATA/ATAPI interface, if there is one. Pressing the Enter key selects the Secondary Master submenu allowing additional device configuration options for this interface The default setting differs between the US/European and the Japanese model. Selects the display language for the BIOS. Secondary Master: Selects Secondary Master submenu The product number of the optical drive Language: · English (US) · Japanese (JP) [English (US)] 5 LifeBook C Series Notebook BIOS Primary Master Submenu of the Main Menu The Primary Master submenu identifies what ATA devices are installed. *Note that actual hard drive label shown may vary. Depending on the drive type, information such as cylinders, heads and sectors may also be displayed. PhoenixBIOS Setup Utility Main Primary Master [FUJITSU MHT2040AT-(PM)] Item Specific Help Type: Total Sectors: Maximum Capacity: [Auto] LBA Format 78140160 40008MB [16 Sectors] [Enabled] [Multiword DMA 2] [Disabled] Select ATA/ATAPI drive installed here. [Auto] The BIOS auto-types the drive on boot time. Except [Auto] You enter parameters of the drive. [None] The drive is disabled. Multi-Sector Transfers: LBA Mode Control: PIO Transfer Mode: DMA Transfer Mode: F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 2. Primary Master Submenu Table 2: Fields, Options and Defaults for the Primary Master Submenu of the Main Menu Menu Field Type: Options · · · · Auto None CD-ROM Hard Disk Default [Auto] Description Selects the ATA/ATAPI device type. Select Auto to have the type automatically identified by the BIOS at POST. If None is selected, all of the following Set-up items do not appear. Select CD-ROM if a CD-ROM drive is installed at this connection. If Hard Disk is selected, you must specify the number of Cylinders, Heads, and Sectors for the drive. CHS Format (Cylinders, Heads, Sectors) Cylinders: · A number between 0 and 65,535 ­-- This appears only when Hard Disk is selected. When Hard Disk is selected, you can change the value. This field is incremented by pressing the [Spacebar]). This field is decremented by pressing the [] key. You can also change the field by typing in the number. This appears only when Hard Disk is selected. When it is selected, you can change the value. This field is incremented by pressing the [Spacebar]). This field is decremented by pressing the [-] key. The field can also be changed by typing in the number. Heads: · A number between 1 and 16 ­-- 6 Main Menu Table 2: Fields, Options and Defaults for the Primary Master Submenu of the Main Menu Menu Field Sectors: Options · A number between 0 and 63 Default ­-- Description This appears only when Hard Disk is selected. When it is selected, you can change the value. This field is incremented by pressing the [Spacebar]. This field is decremented by pressing the [-] key. The field can also be changed by typing in the number. Displays the maximum capacity of the drive calculated from the parameters of the hard disk when Hard Disk is selected. Maximum Capacity: · Display only ­-- LBA Format (Logical Block Addressing) Total Sectors: Maximum Capacity ­-- ­-- ­-- ­-- The total number of sectors on your hard disk. The maximum capacity of your hard disk. CHS and LBA Formats Multi-Sector Transfers: · · · · · Disabled 2 Sectors 4 Sectors 8 Sectors 16 Sectors [16 Sectors] This option cannot be changed when Auto is selected. Specify the number of sectors per block for multiple sector transfer. LBA Mode Control: · Disabled · Enabled [Enabled] Enables or disables Logical Block Addressing in place of Cylinder, Head, Sector addressing. This can't be changed when Auto is selected. Selects the method for moving data to/from the drive. Autotype the drive to select the optimum transfer mode. This option cannot be changed when Auto is selected. Transfer Mode: · · · · · · · · · · · · · · Standard Fast PIO 1 Fast PIO 2 Fast PIO 3 Fast PIO 4 Multiword DMA 1 Multiword DMA 2 Disabled Mode 0 Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 [Multiword DMA 2] Ultra DMA Mode: [Disabled] Selects the method for moving data to/from the drive. Autotype the drive to select the optimum transfer mode. This option cannot be changed when Auto is selected. A bootable CD-ROM may have a floppy disk format or a hard drive format. When the bootable CD-ROM is used, the drive allocations change automatically without changing the BIOS setup. If a floppy disk format CD-ROM is used, the CD-ROM becomes Drive A. The CD-ROM will only take Drive C: (hard drive format) if the internal hard drive is not present or is disabled. The bootable CD-ROM can never use a C: designation if a formatted internal hard drive is present, since the C: designator is always reserved for the internal hard drive. The boot sequence ignores the new drive designations, but your application software will use the new designations. Be careful of the operating environment when booting from a CD-ROM or you may overwrite files by mistake. 7 LifeBook C Series Notebook BIOS Secondary Master Submenu of the Main Menu The Secondary Master submenu is for the internal CD-ROM drive. The drive type is displayed on this menu as well as the Main menu. Your notebook auto-senses the characteristics of the internal CD-ROM Drive installed. You will not need to modify these settings; they are displayed for your reference. Note that actual drive labels shown may vary. PhoenixBIOS Setup Utility Main Secondary Master [MATSHITADVD-RAM UJ-830S-(SM)] Item Specific Help Type: Multi-Sector Transfers: LBA Mode Control: Transfer Mode: Ultra DMA Mode: [Auto] [Disabled] [Disabled] [Standard] [Disabled] Select ATA/ATAPI drive installed here. [Auto] The BIOS auto-types the drive on boot time. Except [Auto] You enter parameters of the drive. [None] The drive is disabled. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 3. Primary Slave Submenu Table 3: Fields, Options and Defaults for the Primary Slave Submenu of the Main Menu Menu Field Type: Options · · · · Auto None CD-ROM Hard Disk Default [Auto] Description Selects the ATA/ATAPI device type. Select Auto to have the type automatically identified by the BIOS at POST. If None is selected, all of the following Set-up items do not appear. Select CD-ROM or Hard Disk for appropriate drive type installed at this connection. This option cannot be changed when Auto is selected. Specify the number of sectors per block for multiple sector transfer. Multi-Sector Transfers: · · · · · Disabled 2 Sectors 4 Sectors 8 Sectors 16 Sectors [Disabled] LBA Mode Control: · Disabled · Enabled [Disabled] Enables or disables Logical Block Addressing in place of Cylinder, Head, Sector addressing. This option cannot be changed when Auto is selected. 8 Main Menu Table 3: Fields, Options and Defaults for the Primary Slave Submenu of the Main Menu Menu Field Transfer Mode: Options · · · · · · · · · · · · · · Standard Fast PIO 1 Fast PIO 2 Fast PIO 3 Fast PIO 4 Multiword DMA 1 Multiword DMA 2 Disabled Mode 0 Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Default [Standard] Description Selects the method for moving data to/from the drive. Autotype the drive to select the optimum transfer mode. This option cannot be changed when Auto is selected. Ultra DMA Mode: [Disabled] Selects the method for moving data to/from the drive. Autotype the drive to select the optimum transfer mode. This option cannot be changed when Auto is selected. Exiting from Main Menu When you have finished setting the parameters on this menu, you can either exit from the setup utility, or move to another menu. If you wish to exit from the setup utility, press the [Esc] key or use the cursor keys to go to the Exit menu. If you wish to move to another menu, use the cursor keys. 9 LifeBook C Series Notebook BIOS ADVANCED MENU ­ SETTING DEVICE FEATURE CONTROLS The Advanced Menu allows you to: · Set the I/O addresses for the ports. · Set the communication mode for the parallel and infrared ports. · Set the features of the keyboard/mouse. · Select between the display panel and an external CRT display. · Configure IDE devices in your system. · Configure CPU features. · Configure USB features. · Configure the power button. · View DMI Event Logging Follow the instructions for Navigating Through the Setup Utility to make any changes. See Navigating through the Setup Utility for more information. The following tables show the names of the menu fields for the Advanced Menu and its submenus, all of the options for each field, the default settings and a description of the field's function and any special information needed to help understand the field's use. Note that not all fields appear in all configurations; the fields that appear are dependent upon the system CPU. Main Advanced PhoenixBIOS Setup Utility Security Boot Info Exit Item Specific Help F1 Help ESC Exit Serial/Parallel Port Configurations Keyboard/Mouse Features Video Features Internal Device Configurations CPU Features USB Features Miscellaneous Configurations Event Logging Configures serial ports and parallel ports. Select Item Select Menu -/Space Change Values Enter Select Sub-Menu Figure 4. Advanced Menu F9 Setup Defaults F10 Save and Exit 10 Advanced Menu Table 4: Fields, Options and Defaults for the Advanced Menu Menu Field Serial/Parallel Port Configurations Keyboard/Mouse Features Video Features Description When selected, opens the Serial/Parallel Port Configurations submenu which allows the user to modify settings for the infrared and parallel ports. When selected, opens the Keyboard/Mouse Features submenu, which enables and disables the power-on state for [NumLock]. When selected, opens the Video Features submenu, which allows setting of the display parameters, including routing of video signals to different displays. When selected, opens the Internal Device Configuration submenu, which allows enabling or disabling the IDE Controller. When selected, opens the CPU Features submenu, which allows enabling or disabling the SpeedStepTM Technology feature for optimal battery life. When selected, opens the USB Features submenu, which allows enabling or disabling of Legacy Floppy Emulation. When selected, opens the Miscellaneous Configurations submenu, which allows you to configure the power button. When selected, opens the event logging submenu. Internal Device Configurations CPU Features USB Features Miscellaneous Configurations Event Logging 11 LifeBook C Series Notebook BIOS Serial/Parallel Port Configuration Submenu of the Advanced Menu The Serial/Parallel Port Configuration submenu provides the ability to set the I/O addresses and interrupt levels for the serial (infrared) and parallel ports of your notebook. I/O addresses, DMA channels, and Interrupt levels can be entered in various ways, including via the BIOS setup utility, the control software for the I/O device, or the hardware. If any two ports or devices have the same I/O address assigned, your notebook will not function normally. · To prevent IRQ and address conflicts, avoid changing the default settings. If you must change the settings, you can call 1-800-8FUJITSU for technical assistance. · The BIOS will warn you of a resource conflict by placing a yellow asterisk next to each device that is in conflict. · All I/O addresses in Table 5 are in hexadecimal. PhoenixBIOS Setup Utility Advanced Serial/Parallel Port Configurations Serial Port: I/O Address: Interrupt: Infrared Port: Mode: I/O Address: Interrupt: I/O Address: DMA Channel: Parallel Port: Mode: I/O Address: Interrupt: Enabled [3F8 - 3FF] [IRQ 4] [Enabled] [FIR] [2E8 - 2EF] [IRQ 3] [400 - 43F] [DMA 3] [Enabled] [Bi-directional] [378-37F] [IRQ 7] Item Specific Help [Disabled] The port is disabled. [Enabled] The port is enabled with user configuration. [Auto] Plug & Play OS configure the port. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 5. Serial/Parallel Port Configuration Submenu 12 Advanced Menu Table 5: Fields, Options and Defaults for the Port Configuration Submenu of the Advanced Menu Menu Field Serial Port: Options · Disabled · Enabled · Auto Default [Enabled] Description When [Enabled] is selected, the port is on. When [Disabled] is selected, the serial port is turned off. When [Auto] is selected, the Plug & Play feature configures the port. Note that for systems running Windows XP, this legacy port is not supported without additional device-specific drivers. Select the I/O address for the serial port. (Note that if there is a conflict between the port interrupts or addresses, asterisks will appear adjacent to the affected port names to alert you to the fact. In that case, make a different selection.) Allows user to set the infrared port base I/O address when the serial port is Enabled. (Note that if there is a conflict between the port interrupts or addresses, asterisks will appear adjacent to the affected port names to alert you to the fact. In that case, make a different selection.) When Disabled, the infrared port is off; when Enabled, the infrared port is on. When Auto is selected, the Plug & Play operating system configures the port. Select the mode for the infrared port: Infrared or Fast Infrared. Allows user to set the infrared port base I/O address when the infrared port is Enabled. (Note that if there is a conflict between the port interrupts or addresses, asterisks will appear adjacent to the affected port names to alert you to the fact. In that case, make a different selection.) [IRQ 3] Allows user to set the infrared port interrupt when the infrared port is Enabled. (Note that if there is a conflict between the port interrupts or addresses, asterisks will appear adjacent to the affected port names to alert you to the fact. In that case, make a different selection.) I/O Address: · · · · 3F8 - 3FF 2F8 - 2FF 3E8 - 3EF 2E8 - 2EF [3F8 - 3FF] Interrupt: · · · · IRQ 3 IRQ 4 IRQ 10 IRQ 11 [IRQ 4] Infrared Port: · Disabled · Enabled · Auto · IrDA · FIR · · · · 3F8 - 3FF 2F8 - 2FF 3E8 - 3EF 2E8 - 2EF [Enabled] Mode: [FIR] I/O Address: [2E8 - 2EF] Interrupt: · · · · IRQ 3 IRQ 4 IRQ 10 IRQ 11 13 LifeBook C Series Notebook BIOS Table 5: Fields, Options and Defaults for the Port Configuration Submenu of the Advanced Menu Menu Field I/O Address: Options · · · · 400 - 43F 480 - 4BF 500 - 53F 580 - 5BF Default [400 - 43F] Description Allows user to set the infrared port base I/O address when the Fast Infrared (FIR) port is Enabled. (Note that if there is a conflict between the port interrupts or addresses, asterisks will appear adjacent to the affected port names to alert you to the fact. In that case, make a different selection.) [DMA 3] Select the direct memory access channel for fast infrared (FIR). Configures the parallel port using either no configuration (Disabled), a user defined configuration (Enabled), or by allowing the BIOS or OS to choose the configuration (Auto). When the parallel port is enabled this option is available allowing the user to set the mode for the parallel port. Bidirectional allows two-way transfer of information between your notebook and a connected parallel device. Output Only (Half Duplex) allows information to be transferred in only one direction, from your notebook to the printer or similar device. ECP Mode allows communication with the ECP class of parallel I/O devices. Check your device documentation for the proper setting. Allows user to set the parallel port base I/O address when the parallel port is Enabled. DMA Channel: · DMA 1 · DMA 3 · Disabled · Enabled · Auto Parallel Port: [Enabled] Mode: · Output Only · Bi-directional · ECP [Bi-directional] I/O address: · 378 - 37F · 278 - 27F · 3BC - 3BF · IRQ 5 · IRQ 7 [378 - 37F] Interrupt: [IRQ 7] Allows user to set the parallel port interrupt when the parallel port is Enabled. 14 Advanced Menu Keyboard/Mouse Features Submenu of the Advanced Menu The Keyboard/Mouse Features submenu is for selecting the power-on state for the NumLock key. Advanced PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help Keyboard/Mouse Features Numlock [Off] Select power-on state for Numlock. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 6. Keyboard/Mouse Features Submenu Table 6: Fields, Options and Defaults for the Keyboard/Mouse Submenu of the Advanced Menu Menu Field Numlock: Options · On · Off Default [Off] Description Sets the NumLock function state when the computer completes booting. 15 LifeBook C Series Notebook BIOS Video Features Submenu of the Advanced Menu The Video Features Submenu is for choosing the display. PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help Main Advanced Video Features Display: Compensation: [Auto]] [Enabled] Select display terminal. * This setting is not effective after operating system starts up. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 7. Video Features Submenu Table 7: Fields, Options and Defaults for the Video Features Submenu of the Advanced Menu Menu Field Display: Options · Internal Flat Panel · External · Auto · Disabled · Enabled Default [Auto] Description Selects where the video signal will be routed. Compensation: [Enabled] Enables or disables video compensation. 16 Advanced Menu Internal Device Configurations Submenu of the Advanced Menu The Internal Device Configurations submenu allows the user to enable or disable Primary and/or Secondary IDE ports, Modem Controller, and Wireless LAN module. Main Advanced PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help [Disabled] No IDE ports are enabled. [Primary] Only primary IDE port is enabled. [Secondary] Only secondary IDE port is enabled. [Both] Both primary and secondary IDE ports are enabled. Internal Device Configurations IDE Controller: Modem Controller: LAN Controller: [Both] [Enabled] [Enabled] F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 8. Internal Device Configuration Submenu Table 8: Fields, Options and Defaults for the Internal Device Configuration Submenu of the Advanced Menu Menu Field IDE Controller: Options · · · · Disabled Primary Secondary Both Default [Both] Description Enables or disables IDE controllers. Modem Controller: LAN Controller: · Disabled · Enabled · Disabled · Enabled [Enabled] Enables or disables the modem. [Enabled] Enables or disables the LAN device. 17 LifeBook C Series Notebook BIOS CPU Features Submenu of the Advanced Menu The CPU Features Submenu configures the system processor. Note that this submenu only appears in certain configurations, based upon the system CPU. PhoenixBIOS Setup Utility Security Power Savings Exit CPU Features Item Specific Help Main Advanced SpeedStep(R) Technology: On Battery: On AC: [Enabled] [Battery Optimized] [Maximum Performance] Select Enhanced Intel(R) SpeedStep(R) Technology enabled or disabled. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 9. CPU Features Submenu Menu Field SpeedStep® Technology: Options · Disabled · Enabled Default [Enabled] Description When Enabled is selected, CPU speed and battery use can be selected from On Battery and On AC. When Disabled is selected, SpeedStep Technology is disabled. When Maximum Performance is selected, CPU speed is maximized. When Battery Optimized is selected, CPU power requirements are optimized for battery operation. When Automatic is selected, the CPU speed is determined by the power source used. When Maximum Performance is selected, CPU speed is maximized. When Battery Optimized is selected, CPU power requirements are optimized for battery operation. When Automatic is selected, the CPU speed is determined by the power source used. On Battery: · Maximum Performance · Battery Optimized · Automatic [Battery Optimized] On AC: · Maximum Performance · Battery Optimized · Automatic [Maximum Performance] 18 Advanced Menu USB Features Submenu of the Advanced Menu The USB Features Submenu allows for the enabling or disabling of SCSI SubClass support, thus enabling support for USB mass storage devices that belong to the SCSI SubClass. Examples of such devices include USB memory keys and floppy drives. Main Advanced PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help USB Features Legacy USB Support: SCSI SubClass Support: [Enabled] [Enabled] [Disabled] The feature is disabled. [Enabled] Legacy USB Emulation is enabled, and USB devices are available without USB-aware OS. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 10. USB Features Submenu Table 10: Fields, Options and Defaults for the USB Features Submenu of the Advanced Menu Menu Field Legacy USB Support: Options · Disabled · Enabled Default [Enabled] Description When Enabled is selected, Legacy USB Emulation is enabled and USB devices are available without a USBaware OS. When Disabled is selected, Legacy USB Emulation is disabled. When Enabled is selected, USB devices that belong to the SCSI subclass in the mass storage class (e.g., USB Memory Key) are enabled. Note that enabling this feature may cause the system to hang during POST, depending on the device that is connected. SCSI SubClass Support: · Disabled · Enabled [Enabled] 19 LifeBook C Series Notebook BIOS Miscellaneous Configurations Submenu of the Advanced Menu The Miscellaneous Configurations Submenu configures the power button. PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help Main Advanced Miscellaneous Configurations Power Button: Wake up on LAN: Volume Setting: [Disabled] [Disabled] [Middle] Configures the power button. *ACPI OS ignores this setting. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 11. Miscellaneous Configurations Submenu Table 11: Fields, Options and Defaults for the Miscellaneous Configuration Submenu of the Advanced Menu Menu Field Power Button: Options · Disabled · Power Off Default [Disabled] Description When Disabled is selected, the power button does not control power. When Power Off is selected, pressing the power button shuts off power to the system. When [Enabled], the system wakes up when the internal LAN device receives a Magic Packet while in Power-Off state. Select the default volume level of the system speakers. Wake up on LAN: Volume Setting: · Disabled · Enabled · · · · Off Minimum Middle Maximum [Disabled] [Middle] 20 Advanced Menu Event Logging Submenu of the Advanced Menu The Event Logging Submenu configures event logging features for DMI events. PhoenixBIOS Setup Utility Security Power Savings Exit Item Specific Help Main Advanced Event Logging Event Log Capacity: Event Log Validity: View Event Log: Event Logging: System Boot Event: Clear All Event Logs: Mark Events as Read: Space Available Valid [Enter] [Enabled] [Disabled] [No] [Enter] Press key to view the contents of the event log. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu F9 Setup Defaults F10 Save and Exit Figure 12. Event Logging Submenu Table 12: Fields, Options and Defaults for the Event Logging Submenu of the Advanced Menu Menu Field Event Log Capacity: Event Log Validity: View Event Log: Event Logging: · Enter · Disabled · Enabled · Disabled · Enabled · No · Yes · Enter Options Default Space Available Valid [Enter] [Enabled] Description Display only Display only Allows you to view content of event log Turns event logging on and off for all DMI events. System Boot Event: [Disabled] Turns event logging on and off for DMI system boot events. When set to [Yes] all event logs will be cleared at next boot. Allows you to make all events currently in the event log as having been read. Clear All Event Logs: [No] Mark Events as Read: [Enter] 21 LifeBook C Series Notebook BIOS SECURITY MENU ­ SETTING THE SECURITY FEATURES The Security menu allows you to set up the data security features of your notebook to fit your operating needs and to view the current data security configuration. Follow the instructions for Navigating Through the Setup Utility to make any changes. See Navigating through the Setup Utility for more information. The tables show the names of the menu fields for the Security menu and its submenus, all of the options for each field, the default settings and a description of the field's function and any special information needed to help understand the field's use. The default condition is no passwords required and no write protection. If you set a password, write it down and keep it in a safe place. If you forget the password, you will have to contact your support representative to regain access to your secured functions and data. n Entering a password incorrectly 3 times in a row will cause the keyboard and mouse to be locked out and the warning [System Disabled] to be displayed. If this happens restart the computer by turning the power off and on with the power switch and use the correct password on reboot. If you make an error when re-entering the password a warning will be displayed on the screen. To try again press [Enter] and retype the password. Press [Esc] to abort the password setting process. If Password On Resume is Enabled and Password On Boot is Disabled you will not have to type your password upon resuming the system from the Suspend or Save-to-Disk modes. Password On Resume will work only if Password On Boot is enabled. Boot sector protection must be set to [Normal] to install or upgrade an operating system. n n n Main Advanced PhoenixBIOS Setup Utility Security Boot Info Exit Item Specific Help Supervisor Password Is: User Password Is: Set Supervisor Password Set User Password Minimum User Password Length: Password on Boot: On Automatic Wake up: KB Lock on Resume: Boot from Removable Media: Flash Write: Hard Disk Security Owner Information Clear Clear [Enter] [Enter] [0] [Disabled] [Disabled] [Disabled] [All] [Enabled] Press [Enter] key to set Supervisor Password to enable any password features. Then password entry is required to enter BIOS Setup. F1 Help ESC Exit Select Item Select Menu -/Space Change Values Enter Select Sub-Menu Figure 13. Security Menu F9 Setup Defaults F10 Save and Exit 22 Security Menu Table 13: Fields, Options and Defaults for the Security Menu Menu Field Supervisor Password is: User Password is: Set Supervisor Password Options ­-- Default Clear Description A display-only field. Set is displayed when the system supervisor password is set and Clear when it is not. A display-only field. Set is displayed when the general user password is set and Clear when it is not. Sets, changes or cancels the Supervisor Password. The Supervisor Password may be up to seven characters and must include only letters or numbers (no symbols). Passwords are NOT case-sensitive. To cancel a password press [Enter] instead of entering characters in the Enter New Password field and Reenter New Password fields. When a Supervisor Password is set it must be used to access the BIOS setup utility. This field can only be accessed if Supervisor Password is set. This field sets, changes, or cancels User Password. User Password may be up to seven characters and must include only letters or numbers (no symbols). Passwords are NOT case-sensitive. To cancel a password, press the Enter key instead of entering characters in the Enter New Password field and in the Re-enter New Password field. When a User Password is set it must be used to access the BIOS setup utility. Sets the minimum length for the user password. Requires a supervisor password in order to be set. When set to Disabled, no password is required. When set to First Boot, a password (User or Supervisor) is required after the Power On Self Test (POST) before the operating system will be read from a disk. If Every Boot is set, a password (User or Supervisor) is required after the Power On Self Test (POST) every time the system is booted (before the operating system is read from the disk). When set to Disabled, it is not necessary to enter a password to wake up from LAN or Real Time Clock (RTC). When Enabled, it is still necessary to enter a password after automatic wake-up. When set to Enabled, the PS/2 mouse and keyboard inputs are locked out upon Resume from Suspend or Save to Disk mode until you enter the password. When set to Disabled no password is required. If no Supervisor Password is set, this feature is not available and no password is required. If Supervisor Only is selected, only the supervisor can boot from removable media. If All is selected, anyone can boot from removable media. ­-- ­-- Clear [Enter] Set User Password ­-- [Enter] Minimum User Password Length: Password on Boot: ­-- [0] · Disabled · First Boot · Every Boot [Disabled] On Automatic Wake-up: KB Lock on Resume: · Disabled · Enabled · Disabled · Enabled [Disabled] [Disabled] Boot from Removable Media: Flash Write: · All · Supervisor only · Disabled · Enabled ­-- [All] [Enabled] When disabled, the BIOS Flash memory is write protected; when enabled, it is not. Configures hard disk security features. Hard Disk Security: Owner Information: ­-- ­-- ­-- Sets Owner information. 23 LifeBook C Series Notebook BIOS Hard Disk Security Submenu of the Security Menu