User manual TANDBERG DLT-V4 - SPECIFICATION MANUAL

PRODUCT SPECIFICATION TAPE DRIVE DLT-V4 DLT-V4 Product Specification, 81-81502-01 A01, November 2005, Made in USA. COPYRIGHT STATEMENT Copyright 2005 by Tandberg Data. All rights reserved. Your right to copy this document is limited by copyright law. Making copies or adaptations without prior written authorization of Tandberg Data is prohibited by law and constitutes a punishable violation of the law. TRADEMARK STATEMENT Tandberg Data and the Tandberg Data logo are trademarks of Tandberg Data. Quantum, the Quantum logo, DLT, DLTtape, the DLTtape logo, and Super DLTtape logo are all registered trademarks of Quantum. DLTIce, DLTSage, and Super DLTtape are all trademarks of Quantum. Other company and product names used in this document are trademarks, registered trademarks, or service marks of their respective owners. Contents Preface ix Chapter 1 Physical Specifications 1 Physical Description ........................................................................................................ 2 Physical Dimensions and Weights ......................................................................... 2 Internal Tape Drive Mounting Hole Dimensions........................................................ 4 Chapter 2 Functional Specifications 7 Chapter 3 Performance Specifications 9 Timing Characteristics................................................................................................... 10 Data Cartridge and Media Characteristics ................................................................. 11 Reliability Factors ........................................................................................................... 11 Chapter 4 Power Specifications 12 Current Specifications.................................................................................................... 13 External Power Supply and Chassis Requirements .................................................. 14 DLT-V4 Product Specification iii Contents Chapter 5 Environmental Specifications 15 Temperature and Humidity Ranges............................................................................ 16 Altitude ............................................................................................................................ 17 Chapter 6 Shock and Vibration Specifications 18 Operating Shock and Vibration Specifications .......................................................... 19 Operating Shock Specifications............................................................................. 19 Operating Vibration Specifications ...................................................................... 19 Non-operating Shock and Vibration Specifications .................................................. 21 Non-operating Shock Specifications .................................................................... 21 Non-operating Packaged Vibration Specifications ............................................ 21 Non-operating Unpackaged Vibration Specifications....................................... 23 Chapter 7 Emission and Immunity Specifications 24 Emissions ......................................................................................................................... 24 Radiated Emissions................................................................................................. 25 Conducted Emissions ............................................................................................. 25 Harmonic Current Emissions ................................................................................ 25 Acoustic Noise Emissions ...................................................................................... 27 Immunities ...................................................................................................................... 28 Electrostatic Discharge (ESD) Immunity ............................................................. 28 Radiated Immunity................................................................................................. 28 Fast Transient Immunity........................................................................................ 29 Surge Immunity....................................................................................................... 29 Conducted Immunity ............................................................................................. 29 Power Frequency Magnetic Field Immunity ...................................................... 29 Voltage Dips, Short Interruptions, and Variations Immunity.......................... 30 Voltage Fluctuations and Flicker Limits ..................................................................... 31 Direct Current (DC) Magnetic Field Interference...................................................... 31 Chapter 8 Safety Specifications 32 Safety Requirement ........................................................................................................ 32 Consumer Bulletin Scheme ........................................................................................... 32 DLT-V4 Product Specification iv Contents Appendix A Regulatory Statements 33 Environmental Compliance .......................................................................................... 37 Disposal of Electrical and Electronic Equipment ...................................................... 37 Glossary 38 DLT-V4 Product Specification v Figures Figure 1 Figure 2 Internal Tape Drive Mounting Hole Dimensions (Bottom View) ....... 5 Mounting Hole Dimensions (Side View) ................................................ 6 DLT-V4 Product Specification vi Tables Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Table 9 Table 10 Table 11 Table 12 Table 13 Table 14 Table 15 Table 16 Table 17 Physical Dimensions .................................................................................... 2 Weight Specifications ................................................................................... 2 Proper and Acceptable DLT-V4 Tape Drive Orientation........................3 Functional Specifications .............................................................................7 Tape Drive Timing Characteristics........................................................... 10 Data Cartridge and Media Characteristics.............................................. 11 Reliability Factors ....................................................................................... 11 Current Specifications ................................................................................ 13 Common Mode Noise Limitations........................................................... 14 Operating Ranges ....................................................................................... 16 Non-Operating Ranges (Packed or Unpacked)...................................... 16 Half Sine Wave Pulse Shock Operating Vibration Specifications ....... 19 Random Overstress Operating Vibration Specifications ...................... 19 Random Overstress Operating Vibration Specifications (PSD Spectrum) ................................................................................................. 20 Sweep / Dwell Operating Vibration Specifications .............................. 20 Non-operating (Unpackaged) Shock Specifications .............................. 21 Random Survival Non-operating (Packaged) Vibration Specifications ........................................................................................... 21 vii DLT-V4 Product Specification Tables Table 18 Table 19 Table 20 Table 21 Table 22 Table 23 Table 24 Table 25 Table 26 Table 27 Table 28 Table 29 Table 30 Table 31 Table 32 Table 33 Table 34 Table 35 Table 36 Random Overstress Non-operating Vibration Specifications (PSD Spectrum) ....................................................................................... 22 Impact Drop Non-operating (Packaged) Shock (Drop) Specifications ........................................................................................... 22 Random Non-operating (Unpackaged) Vibration Specifications........ 23 Standalone Random Non-operating (Unpackaged) Vibration Specifications (PSD Spectrum).............................................................. 23 Sweep/Dwell Non-operating (Unpackaged) Vibration Specifications ........................................................................................... 23 Radiated Emissions Limits ....................................................................... 25 Conducted Emissions Limits.................................................................... 25 Odd Harmonic Limits for Class A Equipment Limits .......................... 26 Even Harmonic Limits for Class A Equipment...................................... 26 Acoustic Noise Emissions, Nominal ........................................................ 27 Acoustic Noise Declaration for German Noise Declaration Law ........ 27 Electrostatic Discharge (ESD) Immunity Limits..................................... 28 Radiated Immunity Limits ...................................................................... 29 Fast Transient Immunity Limits ............................................................... 29 Surge Immunity Limits .............................................................................. 29 Conducted Immunity Limits..................................................................... 29 Magnetic Field Immunity Limits.............................................................. 30 Voltage Dips, Short Interruptions, and Variations Immunity Limits ........................................................................................................ 30 Voltage Fluctuations and Flicker Limits.................................................. 31 DLT-V4 Product Specification viii Preface This document serves as an easy-to-use information source to familiarize customers and systems professionals with the DLT-V4 tape drive system. The DLT-V4 tape drive is an extension of the Digital Linear Tape (DLT®) product family. This chapter describes the purpose, scope, and audience of this document. It also lists the typographical conventions used in this document. Purpose 0 This document describes the tape drive, listing its physical, functional, and performance specifications, and describing the standards that the tape drive meets. Audience 0 The primary audience for this document consists of engineers and technicians interested in integrating the tape drive into tape libraries and other equipment. Document Organization 0 This document is organized as follows: · Chapter 1, Physical Specifications, contains the physical description of the DLT-V4 tape drive, including the internal and tabletop tape drives, and the environmental temperature and humidity specifications. Chapter 2, Functional Specifications, contains the functional specifications of the DLT-V4 tape drive, including the LED functions. · DLT-V4 Product Specification ix · Chapter 3, Performance Specifications, describes the performance specifications of the DLT-V4 tape drive, including timing characteristics, data cartridge and media characteristics, and the reliability factors of the tape drive. Chapter 4, Power Specifications, describes the power specifications of the DLT-V4 tape drive. Chapter 5, Environmental Specifications, describes the environmental specifications of the DLT-V4 tape drive. Chapter 6, Shock and Vibration Specifications, describes the shock and vibration specifications of the DLT-V4 tape drive. All testing was done on both the internal and tabletop tape drives. Chapter 7, Emission and Immunity Specifications, describes the emission and immunity specifications of the DLT-V4 tape drive. Chapter 8, Safety Specifications, describes the safety specifications of the DLT-V4 tape drive. Appendix A, Regulatory Statements, provides the regulatory statements of the DLT-V4 tape drive. · · · · · · Notational Conventions This document uses the following conventions: Note: Notes emphasize important information related to the main topic. Cautions indicate potential hazards to equipment and are included to prevent damage to equipment. Warnings indicate potential hazards to personal safety and are included to prevent injury. Caution: Warning: This document uses the following: · · · Tape Drive System -- Refers to the complete system including the cartridge. Tape Drive -- Refers to just the tape drive and does not include the cartridge. Right side of the tape drive -- Refers to the right side as you face the component being described. x DLT-V4 Product Specification · · · · Left side of the tape drive -- Refers to the left side as you face the component being described. b -- All binary numbers are succeeded by "b." h -- All hexadecimal numbers are succeeded by "h." Error or attention conditions are represented in parenthesis that translate as follows: (SK=S ASC=AA ASCQ=QQ) where: S -- hexadecimal sense key value AA -- hexadecimal additional sense code QQ -- hexadecimal additional sense code qualifier Typographical Conventions This document uses the following typographical conventions: 0 Element Commands Messages Hexadecimal Notation Binary Notation Decimal Notation Acronyms Abbreviations Convention Uppercase (unless case-sensitive) Uppercase Number followed by lowercase h Number followed by lowercase b Number without suffix Uppercase Lowercase, except where standard usage requires uppercase No units specified (Inches understood unless otherwise specified) Example FORMAT UNIT INVALID PRODUCT NUMBER 25h 101b 512 POST Mb (megabits) MB (megabytes) 0.57 EJECT DISTANCE Dimensions in Figures DLT-V4 Product Specification xi Related Documents The following documents are related to the DLT-V4 tape drive: Document No. 81-81252-xx 81-81422-xx Document Title Bezel Replacement Guide DLT-V4 Product Manual DLT-V4 Quick Start Guide Document Description Provides bezel replacement instructions Provides detailed product information for the tape drive. Provides basic tape drive installation instructions. 81-81355-xx Current SCSI standards documents available from www.t10.org · SCSI Architecture Model (SAM-3) · SCSI Primary Commands (SPC-3) · SCSI Parallel Interface (SPI-5) · SCSI Stream Commands (SSC-3) Current SATA standards documents available from www.serialata.org · Serial ATA 1.0a Specification SCSI Standards Copies of the approved version of the SCSI standards may be obtained from: Global Engineering Documents 15 Inverness Way, East Englewood, CO 80112 (800) 854-7179 or (303) 397-2740 0 DLT-V4 Product Specification xii Chapter 1 1Physical Specifications This chapter contains the physical description of the DLT-V4 tape drive, including the internal and tabletop tape drives, and the environmental temperature and humidity specifications. DLT-V4 Product Specification 1 Chapter 1 Physical Specifications Physical Description Physical Description Physical Dimensions and 1 Weights 1 Table 1 Physical Dimensions Specification Height Internal Tape Drive 1.656 in. (42.05 mm) with the bezel 1.618 in. (41.10 mm) without the bezel 5.748 in. (146.00 mm) behind the bezel 5.807 in. (147.50 mm) with the bezel 8.614 in. (218.80 mm) measured from the rear of the front bezel 8.874 in. (225.40 mm) including the bezel Tabletop Tape Drive 2.608 in. (66.24 mm) Width 8.352 in. (212.13 mm) Length 10.728 in. (272.49 mm) Table 2 Weight Specifications Specification Unit Weight Shipping Weight Internal Tape Drive 3.00 lb. (1.36 kg) 4.39 lb. (1.99 kg) depending on the configuration Tabletop Tape Drive 8.00 lb. (3.63 kg) 11.81 lb. (5.36 kg) depending on the configuration Table 3 shows the acceptable operating orientation for the DLT-V4 tape drive. DLT-V4 Product Specification 2 Chapter 1 Physical Specifications Physical Description Table 3 Proper and Acceptable DLT-V4 Tape Drive Orientation Orientation Top Side Up (typical) Internal Tape Drive Tabletop Tape Drive Left Side Down Right Side Down DLT-V4 Product Specification 3 Chapter 1 Physical Specifications Internal Tape Drive Mounting Hole Dimensions Internal Tape Drive Mounting Hole Dimensions 1 Figure 1 shows the mounting holes and dimensions in a bottom view for the internal tape drive. DLT-V4 Product Specification 4 Chapter 1 Physical Specifications Internal Tape Drive Mounting Hole Dimensions Figure 1 Internal Tape Drive Mounting Hole Dimensions (Bottom View) Data cartridge Notes: The following is additional information for figure 1. · The dimension referenced in boxed note [1] is from the front of the base plate. · The dimension referenced in boxed note [2] is from the right-side tape drive mounting plane to the interior guiding surface of the media opening. · The dimension referenced in boxed note [3] is from the bottom tape drive mounting hole to the interior guiding surface of the media opening. · The tape drive width and length are standard 5¼-inch form factor measurements. · Dimensions are identical on left side and right sides. · Dimensions are in millimeters. The dimensions in brackets [x.x] are in inches. Figure 2 shows the mounting holes and dimensions in a side view for the internal tape drive. DLT-V4 Product Specification 5 Chapter 1 Physical Specifications Internal Tape Drive Mounting Hole Dimensions Figure 2 Mounting Hole Dimensions (Side View) Data cartridge Notes: The following is additional information for figure 2. · The dimension referenced in boxed note [1] is from the front of the base plate. · The dimension referenced in boxed note [2] is from the bottom tape drive mounting plane to the interior guiding surface of the media opening. · Boxed note [3] states that the data cartridge is shown in the ejected position. · The tape drive width and length are standard 5¼-inch form factor measurements. · Dimensions are identical on left side and right sides. · Dimensions are in millimeters. The dimensions in brackets [x.x] are in inches. DLT-V4 Product Specification 6 Chapter 2 2Functional Specifications This chapter contains the functional specifications of the DLT-V4 tape drive, including the LED functions. Table 4 lists the key functional specifications of the DLT-V4 tape drive. Table 4 Functional Specifications Specification Formatted Capacity, Native Mode Formatted Capacity, Compressed Modea Interface Tape Drive Type Recording Type Read Compatibilityb Write Compatibility Form Factor Sustained Transfer Rate, Native Mode Value 160 gigabytes (GB) 320 GB Low-Voltage Differential (LVD) DLT Derivative, streaming; 16-bit LVD Partial Response Maximum Likelihood (PRML) DLT-V4, DLT VS160, DLT VS80 / DLT1 DLT-V4 5¼-in. Half-height Up to 10 megabyte (MB) per second DLT-V4 Product Specification 7 Chapter 2 Functional Specifications Specification Sustained Transfer Rate, Compressed Modea Transfer Rate, Burst Error Rate (Unrecoverable) Value Up to 20 MB / sec 160 MB / sec 1 in 1017 bits (non-media error) a. Compressed values use a nominal 2:1 compression ratio. Actual compression ratios achieved depend on the redundancy of data files being recorded. b. Performance may vary when the tape drive reads data previously written to the DLT VS80 and DLT1 formatted data cartridges. Performance depends on the quality of the data cartridge you are reading, not the DLT-V4 tape drive. DLT-V4 Product Specification 8 Chapter 3 3Performance Specifications This chapter describes the performance specifications of the DLT-V4 tape drive, including timing characteristics, data cartridge and media characteristics, and the reliability factors of the tape drive. DLT-V4 Product Specification 9 Chapter 3 Performance Specifications Timing Characteristics Timing Characteristics Table 5 lists the timing characteristics of the DLT-V4 tape drive. 3 Table 5 Tape Drive Timing Characteristics Specification Read/Write Tape Speed Rewind Tape Speed Linear Search Tape Speed Average Rewind Time Maximum Rewind Time Average Access Time (BOT) Maximum Access Time (from BOT) Load to BOT -- previously recorded tape Unload from BOT Value 118 inches per second 160 inches per second 118 inches per second 68 seconds 135 sec 84 sec 168 sec 90 sec 22 sec (no brush), 61 sec (brush) DLT-V4 Product Specification 10 Chapter 3 Performance Specifications Data Cartridge and Media Characteristics Data Cartridge and Media Characteristics Table 6 lists the data cartridge and media characteristics. Table 6 Data Cartridge and Media Characteristics 3 Characteristic Media Width Media Length Media Type Data Cartridge Dimensions Shelf Life Usage Specification 0.5 in. 1,847 ft Metal Particle 4.1 in. x 4.1 in. x 1.0 in. 30 years minimum @ 20 ºC and 40% relative humidity (non-condensing) 600 hrs (150 full read/write uses) Reliability Factors Table 7 lists the reliability factors for the DLT-V4 tape drive. Table 7 Reliability Factors 3 Factor Head Life MTBF Hours / Cycles 30,000 tape motion hours 250,000 hours Comments Continuous operation. The manufacturer does not warrant that predicted MTBF is representative of any particular unit installed for customer use. Actual figures vary from unit to unit. MTBF is measured at 100% duty cycle, excluding head life. This excludes media errors. Load/Unload 50,000 cycles DLT-V4 Product Specification 11 Chapter 4 4Power Specifications This chapter describes the power specifications of the DLT-V4 tape drive. DLT-V4 Product Specification 12 Chapter 4 Power Specifications Current Specifications Current Specifications Note: 4 The +5 Volt bus is ±5%; the +12 Volt bus is ±10%. Table 8 Current Specifications Mode Power Up Load Tape Unload Tape Write Tape Read Tape Rewind Idle (tape tensioned) Idle (tape untensioned) Idle (no tape) 5VDC Apk 1.6 1.6 1.6 1.9 1.9 1.5 1.3 1.3 1.3 5VDC Arms 1.2 1.3 1.3 1.6 1.4 1.4 1.3 1.3 1.3 12VDC Apk 0.3 2.7 2.6 1.4 1.3 1.4 0.6 0.3 0.1 12VDC Arms 0.1 0.7 0.8 0.5 0.5 0.5 0.2 0.1 0.1 DC Pwr W (typ) 7.2 14.9 16.1 14 13 13 8.9 7.7 7.7 AC Pwr W (typ) 9 20 20 20 19 17 13 12 12 AC Pwr W (max) 18 24 24 21 21 19 14 13 13 DLT-V4 Product Specification 13 Chapter 4 Power Specifications External Power Supply and Chassis Requirements External Power Supply and Chassis Requirements 4 This section lists the common mode noise limitations between enclosures. The noise level cannot exceed the values listed in the following table. All measurements must be administered with an active or differential probe to reduce oscilloscope ground loops. Table 9 Common Mode Noise Limitations First Enclosure Enclosure Chassis (Host Server, Workstation, or DLTV4 Tabletop Enclosure) Enclosure Chassis (Host Server, Workstation, or DLTV-4 Tabletop Enclosure) Second Enclosure DLT-V4 Tape Drive Chassis Common Mode Noise Limit Millivolt (mV) <1 mV Peak to Peak Power Supply Enclosure Ground <300 mV Peak to Peak DLT-V4 Product Specification 14 Chapter 5 5Environmental Specifications This chapter describes the environmental specifications of the DLT-V4 tape drive. The tape drive operates in environments that include general offices and workspaces that consist of: · · · · · · · · Conditioned and marginally-conditioned areas with central or remote air-conditioning Complete temperature and humidity controls Moderate control tolerances Systems capable of maintaining consistent comfort levels. Marginal heating or cooling apparatus No humidity conditioning Uncontrolled tolerances Systems inadequate to maintain constant comfort levels. The tape drive does not conform to environments that consist of: For long-term trouble-free operation, we strongly recommend that you operate and store the tape drive in a clean, smoke-free environment. The following tables provide the operating, non-operating, storage, and shipping environmental specifications for the DLT-V4 tape drive systems (both the internal and the tabletop configurations). DLT-V4 Product Specification 15 Chapter 5 Environmental Specifications Temperature and Humidity Ranges Temperature and Humidity Ranges 5 Table 10 lists the operating temperature and humidity ranges of the tape drive. Table 10 Operating Ranges Specification Temperature Range Airflow Wet Bulb Temperature Temperature Gradient Temperature Shock Relative Humidity Humidity Gradient Value 10 ºC to 40 ºC (50 ºF to 104 ºF) 3.0 CFM (min.) 25 ºC (77 ºF) 11 ºC (19.8 ºF) per hour (across range) 10 ºC (18 ºF) over two minutes 20% to 80% non-condensing 10% per hour Table 11 lists the non-operating storage and shipment temperature and humidity ranges of the tape drive. Table 11 Non-Operating Ranges (Packed or Unpacked) Specification Dry Bulb Temperature Wet Bulb Temperature Temperature Gradient Temperature Shock Relative Humidity Humidity Gradient Value -40 ºC to 66 ºC (-40 ºF to 150.8 ºF) 46 ºC (114.8 ºF) 20 ºC (36 ºF) per hour with 5º margin (across the range) 15 ºC (27 ºF) with 5º margin (over two minutes) 10% to 95% non-condensing 10% per hour DLT-V4 Product Specification 16 Chapter 5 Environmental Specifications Altitude Altitude The tape drive operates normally in pressures from -500 feet to 30,000 feet. 5 DLT-V4 Product Specification 17 Chapter 6 6Shock and Vibration Specifications This chapter describes the shock and vibration specifications of the DLTV4 tape drive. All testing was done on both the internal and tabletop tape drives. DLT-V4 Product Specification 18 Chapter 6 Shock and Vibration Specifications Operating Shock and Vibration Specifications Operating Shock and Vibration Specifications Operating Shock Specifications Table 12 lists the shock specifications for the tape drive while it is operating. 6 6 Table 12 Half Sine Wave Pulse Shock Operating Vibration Specifications Specification Pulse Shape Peak Acceleration Duration Application 5 G Shock ½ Sine Pulse 5G 11 millisecond (ms) X, Y, and Z axis, 10 pulses per axis (± ), 60 total, 1 pulse every 6 seconds 8 G Shock ½ Sine Pulse 8G 10 ms X, Y, and Z axis, 1 pulse per axis (± ), 6 total 62 G Shock ½ Sine Pulse 62 G 2 ms X, Y, and Z axis, 1 pulse per axis (± ), 6 total Operating Vibration Specifications 6 Table 13, table 14, and table 15 list the vibration specifications for the tape drive while it is operating. Table 13 Random Overstress Operating Vibration Specifications Factor Frequency Range Acceleration Level Application Criteria 5 to 800 Hz 0.5 Grms X, Y, and Z axis Comments Top to bottom, 10 minutes per axis (min.) DLT-V4 Product Specification 19 Chapter 6 Shock and Vibration Specifications Operating Shock and Vibration Specifications Table 14 Random Overstress Operating Vibration Specifications (PSD Spectrum) Power Spectral Density (PSD) Spectrum Frequency (Hz) 5 20 200 800 PSD (G2/Hz) 0.0002113 0.0004225 0.0004225 0.0002113 Table 15 Sweep / Dwell Operating Vibration Specifications Factor Frequency Range Acceleration Level Application Criteria 5 to 500 to 5 Hz 0.5 G, 0 to Peak X, Y, and Z axis Comments 1 ­ Upward and Downward Sweep Sweep Rate; ½ octave per minute Dwell on 4 lowest resonances per axis for 15 minutes each DLT-V4 Product Specification 20 Chapter 6 Shock and Vibration Specifications Non-operating Shock and Vibration Specifications Non-operating Shock and Vibration Specifications Non-operating Shock Specifications Table 16 lists the shock specifications for the tape drive without its shipping package (non-operating). 6 6 Table 16 Non-operating (Unpackaged) Shock Specifications Specification Pulse Shape Peak Acceleration Duration Application 40 G Shock Square Wave 40 G 10 ms X, Y, and Z axis, twice in each axis (once in each direction) 142 G Shock ½ Sine Pulse 142 G 2 ms X, Y, and Z axis, twice in each axis (once in each direction) Non-operating Packaged Vibration Specifications 6 Table 17, table 18, and table 19 list the vibration specifications for the tape drive in its shipping package (non-operating). Table 17 Random Survival Non-operating (Packaged) Vibration Specifications Factor Frequency Range Acceleration Level Application Criteria 5 to 200 Hz 1.46 Grms X, Y, and Z axis Comments 30 minutes per axis DLT-V4 Product Specification 21 Chapter 6 Shock and Vibration Specifications Non-operating Shock and Vibration Specifications Table 18 Random Overstress Non-operating Vibration Specifications (PSD Spectrum) Power Spectral Density (PSD) Spectrum Frequency (Hz) 3 100 200 PSD (G2/Hz) 0.0144717 0.0144717 0.0036662 Table 19 Impact Drop Nonoperating (Packaged) Shock (Drop) Specifications Factor Test Type Drop Height Criteria Drop Shock Internal Single Pack = 42 in. External Single Pack = 36 in. Application 10 drops total; 1 each side, 3 edges, 1 corner DLT-V4 Product Specification 22 Chapter 6 Shock and Vibration Specifications Non-operating Shock and Vibration Specifications Non-operating Unpackaged Vibration Specifications Table 20 Random Nonoperating (Unpackaged) Vibration Specifications Table 20, table 21, and table 22 lists the vibration specifications for the tape drive without its shipping package (non-operating). 6 Factor Frequency Range Acceleration Level Application Criteria 5 to 500 Hz 2.41 Grms X, Y, and Z axis 30 minutes per axis (min.) Comments Table 21 Standalone Random Non-operating (Unpackaged) Vibration Specifications (PSD Spectrum) Power Spectral Density (PSD) Spectrum Frequency (Hz) 5 100 137 350 500 PSD (G2/Hz) 0.0201 0.0201 0.0107 0.0107 0.0052 Table 22 Sweep/Dwell Nonoperating (Unpackaged) Vibration Specifications Factor Frequency Range Acceleration Level Application Criteria 5 to 500 to 5 Hz 1.0 Grms, 0 to Peak X, Y, and Z axis Comments 1 ­ Upward and Downward Sweep Sweep Rate; ½ octave per minute Dwell on 4 lowest resonances per axis for 15 minutes each DLT-V4 Product Specification 23 Chapter 7 7Emission and Immunity Specifications This chapter describes the emission and immunity specifications of the DLT-V4 tape drive. Emissions The tape drive meets the following standards: · · · · · · · · FCC CFR Part 15 Class B (ANSI C63.4: 1992, IEC/CISPR 22: 1997, +A1: 2000, +A2: 2003 Class B) EMC Directive (89/336/EEC) EN 55022: 1998, +A1: 2000, +A2: 2003 Class B IEC/CISPR 22: 1997, +A1: 2000, +A2: 2003 Class B VCCI-03: 2004 Class B CNS 13438 AS/NZS 3548 ICES ­ 0003 7 DLT-V4 Product Specification 24 Chapter 7 Emission and Immunity Specifications Emissions Radiated Emissions 7 The tape drive meets the radiated emissions limits per IEC/CISPR 22: 1997, +A1: 2000, +A2: 2003 Class B listed in table 23. Table 23 Limits Radiated Emissions Frequency Range Megahertz (MHz) 30 to 230 230 to 1000 Quasi-peak limit decibel (dB) microVolt per meter (µV/m) @ 10m 30 37 Conducted Emissions 7 The tape drive meets the conducted emissions limits per IEC/CISPR 22: 1997, +A1: 2000, +A2: 2003 Class B listed in table 24. Table 24 Conducted Emissions Limits Limits dB (µV) Frequency Range (MHz) 0.15 to 0.50 0.50 to 5 5 to 30 Quasi­peak 66 to 56a 56 60 Average 56 to 46a 46 50 a. The limit decreases with the logarithm of the frequency. The tape drive meets this standard: EN 61000­3­3: 2001, Limitation of voltage fluctuations and flicker in low-voltage supply systems for equipment with rated current up to and including 16A. Table 25 lists the odd harmonic limits for Class A equipment. The harmonics of the input current do not exceed the maximum permissible values given in this table multiplied by a factor of 1.5. Harmonic Current Emissions 7 DLT-V4 Product Specification 25 Chapter 7 Emission and Immunity Specifications Emissions Table 25 Odd Harmonic Limits for Class A Equipment Limits Harmonic Order (n) 3 5 7 9 11 13 15 <= n <= 39 Maximum Permissible Harmonic Current (A) 2.3 1.14 0.77 0.40 0.33 0.21 0.15 x (15/n) Table 26 lists the even harmonic limits for Class A equipment. Table 26 Even Harmonic Limits for Class A Equipment Harmonic Order (n) 2 4 6 8 <= n <= 40 Maximum Permissible Harmonic Current (A) 1.08 0.43 0.30 0.23 x (8/n) DLT-V4 Product Specification 26 Chapter 7 Emission and Immunity Specifications Emissions Acoustic Noise Emissions 7 Table 27 lists the acoustic noise emission levels, both as noise power and sound pressure for the tape drive. The table provides the preliminary declared values per ISO 9296 and 7779 / EN27779. Table 27 Acoustic Noise Emissions, Nominal Mode Noise Power Emission Level (LwA, B) Internal Tabletop Not applicable 5.8 Sound Pressure Level (LpAm, dBA) (bystander positions) Internal Not applicable 54 Tabletop Not applicable 54 Idle Streaming Not applicable 5.8 Note: Current values for specific configurations are available from product representatives. Table 28 lists the acoustic noise declaration for the German Noise Declaration Law. Table 28 Acoustic Noise Declaration for German Noise Declaration Law Schallemissionswerte ­ Werteangaben nach ISO 9296 und ISO 7779 / DIN EN27779 Schalleistungspegel Schalldruckpegel LpAm, dBA (Zuschauerpositionen) Betrieb 5,8 Leerlauf N/A Betrieb 54 LwA, B Gerät DLT-V4 Leerlauf N/A Note: Aktuelle Werte für spezielle Ausrüstungsstufen sind über Tandberg Data erhältlich. DLT-V4 Product Specification 27 Chapter 7 Emission and Immunity Specifications Immunities Immunities The tape drive meets the following standards: · · · EMC Directive (89/336/EEC) EN 55024: 1998 Information Technology Equipment ­ Immunity (reference the basic standard IEC 61000­4­n) IEC/CISPR 22: 1997, +A1: 2000, +A2: 2003 Class B Information Technology Equipment ­ Immunity 7 Electrostatic Discharge (ESD) Immunity 7 The tape drive meets the ESD immunity limits per EN 61000­4­2: 2001 listed in table 29 for operator access areas of the tape drive.