Start Here 1 2 Important: Do not connect the USB cable until Step 15 or the software may not install properly. Follow the steps in order. If you have problems during setup, see Troubleshooting at the end of this Guide. Remove all tape and cardboard CAUTION: Make sure you remove all packing material or the device will not work properly. 3 Title in HP Futura Book 14-20 pt., centered Subtitle in 10-14 pt., centered, white Magyar Italiano Japanese Español Norsk Português Russian Simplified Chinese Slovencina Slovenscina Español Svenska TraditionalChinese Thai Türkçe Ukrainian © 2004 Hewlett-Packard Development Company, L.P. English Arabic Bahasa Português Hrvatski Cesky Dansk Nederland Suomi Français Deutsch Greek Hangul Hebrew Magyar Italiano Español Locate components Windows CD print cartridges HP PSC control panel overlay (glossy sticker, may be pre-attached) *32322 Title in HP Futura Book 14-20 pt., centered Subtitle in 10-14 pt., centered, white Magyar Italiano Japanese Español Norsk Português Russian Simplified Chinese Slovencina Slovenscina Español Svenska TraditionalChinese Thai Türkçe Ukrainian Macintosh CD power cord and adapter © 2004 Hewlett-Packard Development Company, L.P. English Arabic Bahasa Português Hrvatski Cesky Dansk Nederland Suomi Français Deutsch Greek Hangul Hebrew Magyar Italiano Español HP Photosmart 2600/2700 series all-in-one User Guide User Guide USB cable* * Purchased separately. The contents of your box may differ. HP PSC 1500 All-in-One series Setup Guide 4 Attach the control panel overlay (if not attached) a Bend the bottom of the control panel overlay. b Remove the bottom tab and the backing from the overlay. c Lift the lid. Insert the tabs of the overlay into the device. Make sure the tabs are inserted correctly before sticking the overlay to the device. d Press down on the overlay to ensure it is firmly attached. Do not press on the LCD area. The tabs must be in the slots. CAUTION: The control panel overlay must be attached for the HP All-in-One to work! 5 Connect the power cord and adapter Important: Do not connect the USB cable until instructed later in this guide. 2 · HP All-in-One 6 On Press the On button After you press the On button, the green light flashes, and then becomes solid. This may take up to a minute. 7 a Load plain white paper b c d 8 Open access door Lower the access door until it stops. Make sure the print carriage moves to the right side. 9 Remove tape from both cartridges Pull the pink tab to remove the tape from both print cartridges. CAUTION: Do not touch the copper-colored contacts or retape the cartridges. HP All-in-One · 3 10 Insert the tri-color print cartridge CAUTION: The device must be On before you can insert the print cartridge. a Hold the tri-color print cartridge with the blue HP logo on top. b Place the tri-color print cartridge in front of the left slot. c Push the cartridge firmly into the slot until it snaps into place. 11 Insert the black print cartridge a Hold the black print cartridge with the blue HP logo on top. b Place the black print cartridge in front of the right slot. c Push the cartridge firmly into the slot until it snaps into place. d Close the access door. 4 · HP All-in-One 12 Align the print cartridges After you insert the cartridges, a print cartridge alignment page prints. (This may take a few minutes.) a Lift the lid. Place the top of alignment page face down in the right front corner of the glass. Close the lid. b Press the Start Scan button. After the On light stops blinking, alignment is complete. Recycle or discard the alignment page. 13 Turn on your computer a Turn on your computer, login if necessary, and then wait for the desktop to appear. b Close any open programs. 14 Choose the correct CD Macintosh Users: a Insert the HP All-in-One Windows CD. b Follow the onscreen instructions. a Locate the HP All-in-One Macintosh CD. b Continue to the next step. Windows Users: If the startup screen does not appear, double-click My Computer, double-click the CD-ROM icon, and then double-click setup.exe. HP All-in-One · 5 15 Connect the USB cable Macintosh Users: Connect the USB cable to the port on the back of the HP All-in-One, and then to any USB port on your computer. Windows Users: You may have to wait several minutes before you see the onscreen prompt to connect the USB cable. Once the prompt appears, connect the USB cable to the port on the back of the HP All-in-One, and then to any USB port on your computer. If you do not see these screens, see Troubleshooting on the next page. 6 · HP All-in-One 16 Finish software installation Macintosh Users: a Insert the HP All-in-One Macintosh CD. b Double-click the HP All-in-One Installer icon. c Make sure you complete all screens, including the Setup Assistant. Congratulations! Windows Users: Follow the onscreen instructions. Complete the Sign up now screen. Congratulations! Troubleshooting Software Problem: (Windows only) You did not see the screen telling you when to connect the USB cable. Action: Remove, and then re-insert the HP All-in-One Windows CD. Refer to Step 14. Problem: (Windows only) The Microsoft Add Hardware screen appears. Action: Click Cancel. Unplug the USB cable, and then insert the HP All-in-One Windows CD. Refer to Steps 14 and 15. Problem: (Windows only) The Device Setup Has Failed To Complete screen appears. Action: Verify that the control panel overlay is firmly attached. Unplug the device and plug it in again. Check all connections. Make sure the USB cable is plugged into the computer. Do not plug the USB cable into a keyboard or nonpowered hub. Refer to Steps 4 and 15. HP All-in-One · 7 Troubleshooting Control Panel Correct: Alerts: *Q5888-90232* *Q5888-90232* Q5888-90232 The first image shows how the control panel overlay looks after a successful setup. The second image shows possible problems. See below for more information. 1 2 3 E 4 Alerts: Action: Check the input tray. The paper was not loaded correctly. Reload the paper, and then press the Cancel/Resume button. Make sure the tape was removed from the cartridges. Re-insert the cartridge and then, close the door. Press the Cancel/ Resume button to continue. Check for other lights to determine the problem. See the User Guide for more information. The overlay is not attached correctly. Refer to step 4. After attaching, press the Cancel/Resume button to continue. 1 2 The Check Paper light is flashing. The Check Print Cartridge light is flashing. 3 4 E An E in the Copies area. The Check Paper, Check Print Cartridge, Start Copy areas are flashing. Printed on at least 50% total recycled fiber with at least 10% post-consumer paper. Visit www.hp.com/support for assistance. © Copyright 2005 Hewlett-Packard Development Company, L.P. Printed in []. ...