1ST PRINTING JUNE 01 Universal Kit Kit Installation Instructions & Service Manual Switchable FROM High Resolution 31K TO Standard (Low) Resolution 15.75K. 1 - 2 PLAYER GAME SEGA ENTERPRISES, INC. USA MANUAL NO. 999-1292 Warranty Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered. Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor. Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void. Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages. This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above. World Series 2001 Sega Naomi System Kit Contains List Part # 400-5397-01 838-13616 560-5407-UL 838-13683-93CV1 600-7141-200 600-7009-2500 840-0051D-01 600-7247-500 LOC. PURCHASE XKT-0833 610-0630-0010 999-1293 999-1294 999-1295 999-1296 999-1297 NOA-20010-01 Desc NAOMI POWER SUPPLY AUDIO POWER AMP 2 CH AUDIO XFORMER 120V JAMMA I/O BD (NAOMI) USB CABLE VGA VIDEO CABLE ASSY CASE PC1 DIMM BD CABLE SCSI TYPE 2 500MM SERVICE SWT BRKT ASSY GD-ROM DRIVE KIT GD SOFT KIT WS2K1 MARQUEE WS2K1 INST SHT AMER LG WS2K1 INST SHT NAT LG WS2K1 INST SHT CONTROL WS2K1 SIDE DECALS WS2K1 CONT PNL ASSY WS2K1 (See Breakdown Next Page.) Qty 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 ASSY CTRL PNL 2A4B2S MB2K2 ENG (NOA-20010-01) (D-1/2) 2 ASSY CTRL PNL 2A4B2S MB2K2 ENG (NOA-20010-01) ITEM NO. 1 2 101 102 103 104 105 106 107 109 201 202 203 204 PART NO. HOT-2023 NOA-2025-01 610-6723-4B02 610-6723-4B01 610-0409 999-1290 999-1086 999-1289 280-5009-01 280-5275-SR10 050-U00400 060-F00400 060-S00400 050-H00400 DESCRIPTION CTRL PNL BASE 2A4B2S CTRL PNL PLATE 2A4B2S ENG (D-2/2) ASSY ANALOG JOY 4B PINK ASSY ANALOG JOY 4B GREEN ASSY BAT MECHA PUSHBUTTON RND YELLOW W/MICRO (2 PER) PUSHBUTTON RND GREEN W/MICRO (2 PER) PUSHBUTTON RND PINK W/MICRO (2 PER) CORD CLAMP 21 CORD CLAMP SR10 U NUT M4 FLT WSHR M4 SPR WSHR M4 HEX NUT M4 3 Feb 9. 2000 SERVICE BULLETIN SEGA Service Department 45133 Industrial Drive Fremont, Ca. 94538 http://www.seuservice.com Phone: 415.701.6580 Fax: 415.701.6594 120 SPECIAL NOTICE FOR ALLSEGANAOMIKITS PROBLEM: The SEGA Naomi Game kits are actually `JAMMA Dependent'. What this means exactly is they will only install into existing JAMMA Cabinets. If an operator tries to install these kits into a Non-JAMMA cabinet, they will first have to bring the wiring up to JAMMA Standards. SOLUTION: ° ° Step 1 Disconnect the games original DC Power Supply. You may only use the power supply provided with your kit. Be sure to set the voltages going to your Game BD to 5.1 and 3.3 volts DC to assure proper operation ( Measure on Square Connector at Game BD. Yellow = 5vdc / Brown = 3.3vdc / White = Gnd ) Step 2 You MUST USE THE COIN METER SUPPLIED WITH YOUR KIT to assure proper Coin acceptance. A minimum 18 Gauge wire should be used from the Coin Meter 1 output line on your JAMMA Harness. The 5vdc ( Yellow ) wire found in the wiring bag of your kit MUST BE USED for the supply voltage to the meter. Not following the directions provided herein may cause your game to malfunction. All electrical work should be performed by the site's Serviceman or Technician. In order to prevent an electric shock and short circuit, be sure to turn power off before performing work or touching the interior parts of the product. Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit accident. Do not touch places other than those specified. Touching places not specified can cause an electric shock or short circuit accident. If you have any questions please contact the SEGA Service Department at the numbers given above. 4 INSTALLATION INSTRUCTIONS 1) First. Remove all access panels from the game. Locate the original game Logic PCB's & Power Supply and remove from the Cabinet by first disconnecting all harnesses from the boards. (You need only to splice in the Main Power (110v AC) into the 3-Pin Connector (GRN/WHT/BLK).) 2) Remove all existing game harnesses (we suggest using New Jamma Harnesses (NOT contained in the kit) to ensure reliability). 3) Locate the most convenient and open area of the cabinet to mount the World Series 2001 Naomi System Assembly. Make sure this area is free and clear of all cable harnesses and grounds, cable clamps, etc. Vacuum out or clean bottom of cabinet of dirt & miscellaneous parts (e.g. screws, loose coins / tokens, etc.). Remove all exterior decals and repair any cabinet damage. Repaint cabinet if necessary. Remove the Monitor Plexi or if your game plexi has Silk-screened artwork, you will need to strip it off. 4) Connect the JAMMA Harnesses to the JVS-JAMMA Interface Boards. Separate the wires from each other (i.e. Control Panel, Video, Speaker, Power Supply). Run the various harnesses to the part of the cabinet they go to ensuring they are dressed properly & secured to the cabinet. Locate the Volume/ Speaker/Coin Meter Cable and connect to your existing Switch Bracket or use the new one included with the kit. Note: If you are using a VGA Compatible Monitor you can run your VGA Cable directly to the monitor or connect it to your JVS JAMMA Interface for RGB Conversion to your JAMMA Cables. 5) Remove Marquee from cabinet and cut to fit the new World Series 2001 Marquee in place. REPLACE old Joysticks & Buttons with the NEW ones supplied in Kit. 6) First remove all Joystick and Button assemblies from the Control Panel. Remove Lexan and Control Panel Overlay. Proceed to clean surface of the Control Panel by removing all adhesive and dirt. Fill in or plug up existing button holes to set up a blank work area for your new controls. 7) Install the new Control Panel Overlay by carefully peeling off the paper backing and laying down on the panel. Smooth it out, starting in the center and working your way to the edges (removing all of the trapped air pockets). If necessary, cut the edges of the overlay excess and fold under panel. 8) Cut out the button and Joystick Holes. Install Joystick and buttons from kit into the Control Panel and tighten down. Connect all game harness wires to switches and buttons. 5 INSTALLATION INSTRUCTIONS 9) Proceed to place new decals on the sides of the cabinet. Locate a new monitor bezel, if needed, and replace glass, if required (due scratches). Install Instruction Placard to the back of the Monitor Glass. NOTE: As a precaution, disconnect the JAMMA Harness from the I/O Boards and turn power on. With a Multi-Meter, measure the 5v and 3.3v. Adjust if necessary to 5.15v DCand 3.3vDC. Measure the +12 to ensure the wires and voltages are in the correct position. Turn power off. Plug in the JAMMA Harness once again to the I/O Boards. The Attract Mode should appear on the screen. Adjust the SIZE, CONTRAST, BRIGHTNESS, and COLORS on the Monitor for optimum appearance. Adjust VERTICAL/HORIZONTAL Hold to get a stable picture, if required. Enter DIAGNOSTICS and adjust the Volume Level, test all Buttons & Joystick for proper operation & wiring. Adjust Pricing. Coin-Up and test out a game to ensure proper play functions are as they should be. 6 Sega Naomi System Switch Bracket and Speaker Installation Diagrams (Figure 3) To CN1 of Amplifier Board Pin 1 Pin 4 Pin 5 JAMMA Pin 8 Yellow Wire from Extra Harness (+5v) _ + GRN/RED WHT/RED YEL/RED Coin Meter Test Service JAMMA Pin JAMMA Pin JAMMA Pin R 1 15 Volume GRY/RED From CN2 of Amplifier Board ORG/RED Left Speaker From CN4 of Amplifier Board GRY/BLUE ORG/BLUE Right Speaker 7 Sega Naomi System JAMMA Harness Wiring (JAMMA I/O BD) (Figure 4) Ground Ground +5v (Not Used) +5v (Not Used) (Not Used) +12v (Not Used) Key Coin Meter 1 (Not Used) (Not Used) (Not Used) Video Red Video Blue Video Ground Test Coin 1 1P Start 1P UP 1P Down 1P Left 1P Right Attack 1P (1P SW1) Grapple 1P (1P SW2) Support 1P (1P SW3) (Not Used) (Not Used) Ground Ground 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 4 28 A B C D E F H J K L M N P R S T U V W X Y Z a b c d e f Ground Ground +5v (Not Used) +5v (Not Used) (Not Used) +12v (Not Used) Key Coin Meter 2 (Not Used) (Not Used) (Not Used) Video Green Video Sync Service (Not Used) Coin 2 2P Start 2P UP 2P Down 2P Left 2P Right Attack 2P (2P SW1) Grapple 2P (2P SW2) Support 2P (2P SW3) (Not Used) (Not Used) Ground Ground 8 Sega Naomi System Filter Board Information Connector Description etc. PSW2 PSW1 DIPSW1 Service Switch CN4 CN3 CN2 CN1 Test Switch Preamp Level Audio Out VGA Level Video Out Power Connectors 1 2 3 4 Setting for High Resolution 31KHZ 1 -4 off 1 2 3 Setting for Standard Resolution 15KHZ 1 on 2-4 off. 9 1. SPECIFICATIONS 1 MONITOR Monitor Position HORIZONTAL Horizontal Synchronous Frequency 15/31 kHz 2 CONTROL PANEL NEW ASTRO CITY, NAOMI CABINET, NET CITY, BLAST CITY (PART NO. HOT-20011 or NOA-20010-01) 00H FFH FFH 00H 00H 1P 2P FFH BBUTTON START FFH ABUTTON ANALOG BAT MECHA LEVER PLAYER 1 FFH 00H BBUTTON 00H FFH ABUTTON ANALOG BAT MECHA LEVER PLAYER 2 00H ANALOG LEVER: Move cursor (for throwing, batting); Specify base (for defense, base running) A BUTTON: Throw (for defense); Steal base (for batting); Advance to next base (for base running) Enter command (within command acceptance time) B BUTTON: Check runner (for throwing); Move between bases (for defense); Return to base (for running) Enter command (within command acceptance time) BAT MECHA: Swing START: Start game; Time out (for throwing, batting) The analog input on the I/O board uses the following channels: CH0 : 1P ANALOG LEVER VOLUME VERTICAL UP(FFH) DOWN(00H) CH1 : 1P ANALOG LEVER VOLUME HORIZONTAL LEFT(FFH) RIGHT(00H) CH2 : 1P BAT MECHA VOLUME STANDARD POS.(00H) MAX(FFH) CH3 : (RESERVE) CH4 : 2P ANALOG LEVER VOLUME VERTICAL UP(FFH) DOWN(00H) CH5 : 2P ANALOG LEVER VOLUME HORIZONTAL LEFT(FFH) RIGHT(00H) CH6 : 2P BAT MECHA VOLUME STANDARD POS.(00H) MAX(FFH) CH7 : (RESERVE) 3 Minimum DIMM Memory Capacity 256 MB 10 Removing and Attaching the BAT MECHA If you need to remove the BAT MECHA as in the case of a failure, open the control panel base and remove the BAT MECHA through the following procedure. To reinstall the BAT MECHA, reverse the removing procedure, being certain that the BAT MECHA is faced in the correct direction. For instructions on opening the control panel base, refer to the Instruction Manual of the cabinet. To prevent electric shock, be sure to turn off the power for the cabinet when removing or attaching the BAT MECHA. 1 Remove the wiring connector (AMP 3P, white) located near the volume. 2 Remove the tamperproof screw clamping the bat center axis on the front side of the control panel. Tightening/loosening of the tamperproof screw should use the tamperproof screw M4 wrench (540-0006-01) that is included as an accessory for the NAOMI CABINET, NET CITY, and NEW ASTRO CITY cabinet. The tamperproof screw M4 wrench is not included with the following cabinets: Versus CITY, New VERSUS CITY, and BLAST CITY. If the wrench is not available, please order the following part numbers: · Wrench type (M4): 540-0006-01 · Screwdriver type (M4): 540-0018 3 Remove the four flange nuts clamping the BAT MECHA body on the back side of the control panel. BAT MECHA Part number: 610-0409 Part name: ASSY BAT MECHA 123 123 The above figure does not show the wiring of the volume and its connector (AMP 3P, white). 11 2. CONTENTS OF GAME · This is a sports action game where the Major League Baseball in the United States of America was taken as a subject matter. · In this game, the following teams appear: 14 American and 16 National teams, and two all-star teams from the two leagues. · The number of players appearing in the game is over 700. All of the 30 really existing ballparks also appear there. · The game player or players operate their favorite teams to participate in the baseball game, aiming at the win. · The following play modes are available: Player vs. CPU, Player vs. Player, and Game of Intrusion. HOW TO PLAY THE GAME · First select your favorite from the 32 teams. Use the lever to designate the selected team, and use the A Button for determination. This applies also to all the subsequent ...