User manual WELLTECH FXO GATEWAY H.323 3804 - VERSION 117

WellGate FXO GateWay User Manual S/W version:x4fxo.117 Notice © Copyright 2003 Welltech Computer Co., Ltd. All intellectual property rights in this publication are owned by Welltech Computer Co., Ltd. and are protected by Republic of China copyright laws, other applicable copyright laws and international treaty provisions. Welltech Computer Co., Ltd. retains all rights not expressly granted. No part of this publication may be reproduced in any form whatsoever or used to make any derivative work without prior written approval by Welltech Computer Co., Ltd. No representation of warranties for fitness for any purpose other than what is specifically mentioned in this guide is made either by Welltech Computer Co., Ltd. or its agents. Welltech Computer Co., Ltd. reserves the right to revise this publication and make changes without obligation to notify any person of such revisions or changes. Welltech Computer Co., Ltd. may make improvements or changes in the product(s) and/or the program(s) described in this documentation at any time. If there is any software on removable media described in this publication, it is furnished under a license agreement included with the product as a separate document. If you are unable to locate a copy, please contact Welltech Computer Co., Ltd. and a copy will be provided to you. Unless otherwise indicated, Welltech Computer Co., Ltd. registered trademarks are registered in the Republic of China and other territories. For further information, contact Welltech or your local distributor or reseller. Welltech Computer Co., Ltd. 13F-4, No.150, Jian-Yi Road, Chung-Ho City, Taipei, Taiwan 235, R.O.C. Tel: +886-2-82265699 Fax: +886-2-82265799 E-mail: sales@mail.welltech.com.tw http://www.welltech.com.tw 2 WellGate 3804 User Manual Table of Contents 1. INTRODUCTION ....................................................................................................................................... 4 1.1 FEATURES AND SPECIFICATION................................................................................................................. 5 1.2 APPEARANCE ........................................................................................................................................... 7 3802: ........................................................................................................................................................ 7 3804: ........................................................................................................................................................ 8 3806: ........................................................................................................................................................ 9 2. SYSTEM OPERATING PROCEDURE...................................................................................................11 2.1 SYSTEM REQUIREMENT ......................................................................................................................... 13 2.2 TELEPHONE LINE REQUIREMENT........................................................................................................... 14 2.3 IP ENVIRONMENT SETTING.................................................................................................................... 14 2.4 HYPER TERMINAL SETTING ................................................................................................................... 15 3. INITIALIZING WELLGATE FXO GATEWAY SETTING ................................................................. 18 3.1 GATEKEEPER MODE............................................................................................................................... 18 3.2 PEER-TO-PEER MODE ............................................................................................................................ 22 3.3 BEHIND IP-SHARING.............................................................................................................................. 23 4. DISCONNECT TONE CONFIGURATION ........................................................................................... 24 4.1 WHAT IS DISCONNECT TONE.................................................................................................................. 24 4.2 HOW TO CONFIGURE DISCONNECT TONE ON WELLGATE FXO GATEWAY GATEWAY .............................. 25 4.3 ADJUST TONE TABLE PARAMETERS MANUALLY .................................................................................... 26 4.4 ADJUST INPUT TONE LEVEL .................................................................................................................. 26 5. COMMAND LISTS................................................................................................................................... 27 5.1 [HELP] COMMAND .................................................................................................................................. 27 5.2 [QUIT] COMMAND .................................................................................................................................. 27 5.3 [DEBUG] COMMAND ............................................................................................................................... 28 5.4 [REBOOT] COMMAND ............................................................................................................................. 28 5.5 [FLASH] COMMAND................................................................................................................................ 29 5.6 [COMMIT] COMMAND............................................................................................................................. 29 5.7 [IFADDR] COMMAND .............................................................................................................................. 29 5.8 [TIME] COMMAND .................................................................................................................................. 31 5.9 [PING] COMMAND .................................................................................................................................. 31 5.10 [GREETRD] COMMAND ......................................................................................................................... 32 5.11 [PBOOK] COMMAND ............................................................................................................................. 34 5.12 [PPPOE] ................................................................................................................................................ 36 5.13 [SYSCONF] COMMAND.......................................................................................................................... 37 5.14 [H323] COMMAND................................................................................................................................ 40 5.15 [VOICE] COMMAND .............................................................................................................................. 43 5.16 [TOS] COMMAND .................................................................................................................................. 45 5.17 [TONE] COMMAND ............................................................................................................................... 45 5.18 [SUPPORT] COMMAND .......................................................................................................................... 46 5.19 [GROUP] COMMAND ............................................................................................................................. 47 5.20 [BUREAU] COMMAND........................................................................................................................... 48 5.21 [PREFIX] COMMAND ............................................................................................................................. 50 5.22 [ROM] COMMAND................................................................................................................................. 51 5.23 [PASSWD] COMMAND ........................................................................................................................... 52 6. UPGRADE THE WELLGATE FXO GATEWAY .................................................................................. 54 TFTP/FTP SERVER ...................................................................................................................................... 54 DOWNLOAD PROCEDURE............................................................................................................................. 54 7. APPENDIX: WEB CONFIGURATION.................................................................................................. 56 3 WellGate FXO GateWay User Manual S/W version:x4fxo.117 1. Introduction The WellGate FXO gateway provides voice/fax service over IP network with H.323 v3 protocol. By connecting to your existing ADSL or cable modem service, which allows the use of a single, network for voice and fax services with consequent saving in network infrastructure and greatly reduced telephone charges. Ideal solution for providing low cost communications between headquarters and branch offices in the world, as well as for SOHO and office telephony applications. WellGate FXO GateWay provides analog lines to connect local PSTN/PTT interface (FXO), and converts voice/fax signal onto IP network. The management feature is via RS-232C COM port and TELNET. 4 WellGate 3804 User Manual 1.1 Features and specification General Features - ITU-T H.323 v3 compliance - Automatically Gatekeeper Discovery - Peer-to-Peer mode (non-Gatekeeper) - Support auto-attendant (2nddial Tone / Voice greeting) - Dimensions : 221mm(W)*42mm(H)*217mm(L) - Line hunting - 2(3802)/4(3804)/6(3806) RJ-11 FXO ports - E.164 (Telephone Number Plan) - DTMF dialing - DTMF detection/generation - TFTP software upgrade - Remote configuration/reset via Telnet - LED indication for system status - LAN interface : One RJ-45 connector of 10Base-T - Microsoft Netmeeting v3.0 compatible - Support static IP and DHCP - QoS by ToS (Type Of Service) - SNTP (Simple Network Time Protocol) - Security: Password setting Audio feature - Codec -- G.711 a/ law, G.723.1 (6.3K/bps), G.729A (Optional) - VAD (Voice Activity Detection), CNG (Comfort Noise Generate) - G.168/165-compliant adaptive echo cancellation - Dynamic Jitter Buffer - Bad Frame Interpolation - Call Transfer (H.450.2) - Call Forward (H.450.3) - Call Hold (H.450.4) - Gain Settings - Provide Call Progress Tone: Dial tone, busy tone, call-holding tone and ring-back tone Management Features: Two easy ways for system configuration 5 WellGate FXO GateWay User Manual S/W version:x4fxo.117 - Console port: RS-232C port TELNET HTTP Brower (e.g. Internet Explorer) 6 WellGate 3804 User Manual 1.2 Appearance 3802: Front panel: The LED light provides system message of WellGate3802. Power : Light on means WellGate3802 is power on. L1-L2 : Light on means the line is in use. Link : Light on means WellGate3802 is connected to the network correctly. Act : LED should be light on and in flash display when data is transmitting. Ready : 1. Light on and in slow flash means WellGate3802 is in operation mode. Status : 1. Light on means WellGate3802 successfully registered to Gatekeeper when it is set as Gatekeeper Mode. 2. LED flash means WellGate3802 is not registered to Gatekeeper when it is set as Gatekeeper Mode. 3. Or when WellGate3802 is in downloading mode, LED should be flash as well. 4. Light off means WellGate3802 is in Peer-to-Peer Mode. Back panel: 7 WellGate FXO GateWay User Manual S/W version:x4fxo.117 3804: Front panel: The LED light provides system message of WellGate FXO GateWay. Power : Light on means WellGate FXO GateWay is power on. L1-L4 : Light on means the line is in use. Link : Light on means WellGate FXO GateWay is connected to the network correctly. Act : LED should be light on and in flash display when data is transmitting. Ready : 1. Light on and in slow flash means WellGate FXO GateWay is in operation mode. Status : 1. Light on means WellGate FXO GateWay successfully registered to Gatekeeper when it is set as Gatekeeper Mode. 2. LED flash means WellGate FXO GateWay is not registered to Gatekeeper when it is set as Gatekeeper Mode. 3. Or when WellGate FXO GateWay is in downloading mode, LED should be flash as well. 4. Light off means WellGate FXO GateWay is in Peer-to-Peer Mode. Back panel: 8 WellGate 3804 User Manual 3806: Front panel: The LED light provides system message of WellGate3806. Power : Light on means WellGate3806 is power on. L1-L6 : Light on means the line is in use. Link : Light on means WellGate3806 is connected to the network correctly. Act : LED should be light on and in flash display when data is transmitting. Ready : 1. Light on and in slow flash means WellGate3806 is in operation mode. Status : 1. Light on means WellGate3806 successfully registered to Gatekeeper when it is set as Gatekeeper Mode. 2. LED flash means WellGate3806 is not registered to Gatekeeper when it is set as Gatekeeper Mode. 3. Or when WellGate3806 is in downloading mode, LED should be flash as well. 4. Light off means WellGate3806 is in Peer-to-Peer Mode. Back panel: 9 WellGate FXO GateWay User Manual S/W version:x4fxo.117 10 Base-T: RJ-45 Modular Jack Female connector with 10 Mbps Ethernet. PIN 1, 2: Transmit PIN 3, 6: Receive COM: RS232 console port (9-pin Male connector, as the same as the computer). Male connector (as the same as the PC) 10 WellGate 3804 User Manual 9 PIN D-SUB MALE at the WellGate FXO GateWay Pin Name Dir Description Receive Data 2 RXD Transmit Data 3 TXD 5 GND System Ground L1 ~ L4: RJ-11 (PSTN or Extension Line of PBX) On / Off: Power switch on/off. 100 - 240 VAC: AC Power supply. 2. System Operating Procedure 11 WellGate FXO GateWay User Manual S/W version:x4fxo.117 START 2.1 System Requirement 2.2 Telephone Line Requirement 2.3 IP Environment Setting 2.4 Hyper Terminal Setting END 12 WellGate 3804 User Manual 2.1 System Requirement 1. One PC (a) Pentium 100 or above, 64 MB DRAM, Windows 98 or above. (b) Network card (RJ-45) & COM port 2. One standard RS-232 straight cable with two female connectors depended on the different model. 3. PSTN lines / PBX extension lines (up to 4 lines). 4. Software tools (a) Hyper terminal, telnet (Windows OS included) (b) Gatekeeper (optional) 13 WellGate FXO GateWay User Manual S/W version:x4fxo.117 2.2 Telephone Line Requirement Two kinds of analog lines can be connected to RJ-11 of WellGate FXO GateWay. 1. PSTN (Public Switched Telephone Network, POTS) or 2. PABX (Private Automatic Branch Exchange) / PBX (Private Branch Exchange) extension line. PSTN 1. It is necessary to provide PSTN/POTS telephone lines in order to plug into RJ-11 of WellGate FXO GateWay. 2. The maximum telephone lines are up to 2(3802)/4(3804)/6(3806). PABX / PBX 1. 2(3802)/4(3804)/6(3806) PSTN lines can be replaced to the 2(3802)/4(3804)/6(3806) extension lines of PBX. Note: Since the Line function feature starts from L1, please plug the telephone lines from L1. 2.3 IP Environment Setting User must prepare a valid IP address to be complied IP Network policy in order for WellGate FXO GateWay operating correctly. For example, if your company's IP address is 192.168.4.111, subnet mask is 255.255.0.0, default gateway is 192.168.1.254, you should prepare one IP for WellGate FXO GateWay, such as IP address is 192.168.4.99, and the same subnet mask and default gateway. 14 WellGate 3804 User Manual 2.4 Hyper Terminal Setting 1. Execute the Hyper Terminal program, then the following windows pop-up on the screen. (START ­ Program files ­ Accessories ­ Communication ­ Hyper Terminal) 2. Define a name such as `3804 Gateway' for this new connection. 15 WellGate FXO GateWay User Manual S/W version:x4fxo.117 3. After pressing OK button, the next window popping up is necessary to connect choose COM Port. Note: Some connection failed is derived the PC COM Port. If user cannot open the com port, for example com 1, please try another com port, ex.com port 2. 4. Configure the COM Port Properties as following: (1) Bits per second : 9600 (2) Flow control : None 16 WellGate 3804 User Manual Press `OK' button, and start to configure WellGate FXO GateWay. 17 WellGate FXO GateWay User Manual S/W version:x4fxo.117 3. Initializing WellGate FXO GateWay Setting 3.1 Gatekeeper Mode START (a) Configure WellGate FXO GateWay Password (b) Configure WellGate FXO GateWay IP Address (c) Gatekeeper Mode Settings (d) Save WellGate FXO GateWay Configuration & Reboot WellGate FXO GateWay END 18 WellGate 3804 User Manual (a) Configure WellGate FXO GateWay Password It is important for the first time user to follow the operation procedure. 1. Power on the WellGate FXO GateWay and the sentence "Please wait while system is initializing............S" is displayed. --------------------------------------------------------------------------------------------Attached TCP/IP interface to cpm unit 0 Attaching interface lo0...done Please wait while system is initializing .......... S 2. Wait around 40 seconds, the login name and password are requested. --------------------------------------------------------------------------------------------Attached TCP/IP interface to cpm unit 0 Attaching interface lo0...done AC4804[0] is OK AC4804[1] is OK AC4804[2] is OK Successful Initialize OSS libraries...OK! open stack successful cmInitialize succeed! GK mode selected. 19 WellGate FXO GateWay User Manual S/W version:x4fxo.117 login: 3. Login: when WellGate FXO GateWay is used for the first time, "root" is default login name without a password. 4. Password setting: type "passwd ­set root ****" to define a password for "root" account. "****", in above description, stands for contents of the password. An example, to set root's password as good, is demonstrated as following: --------------------------------------------------------------------------------------------usr/config$ passwd -set root good Setting login: root Password: good OK (b) Configure WellGate FXO GateWay IP Address Use "ifaddr" command to set up WellGate FXO GateWay's IP address and related network information. An example is demonstrated below: --------------------------------------------------------------------------------------------------usr/config$ ifaddr ­ ip 10.1.1.1 ­ mask 255.2555.255.0 ­ gate 10.1.1.254 Note: this is to assign WellGate FXO GateWay an IP address of "10.1.1.1", subnet mask "255.255.255.0", and default IP gateway "10.1.1.254". (c) Gatekeeper Mode Settings To assign a gatekeeper address for WellGate FXO GateWay, and define its own registered ID and phone number. For detail, please refer to Chapter 5.14 [h323] command. Several important H323 parameters is listed below when setting gatekeeper mode: "­gk", "­e164", and "­alias". 20 WellGate 3804 User Manual An example is demonstrated below: --------------------------------------------------------------------------------------------------------usr/config$ h323 ­ gk 10.2.2.2 ­ e164 ­ alias fxo Note: This is to set gatekeeper IP address as "10.2.2.2", e.164 number as "1", and alias name (h323ID) as "fxo". (d) Save WellGate FXO GateWay Configuration & Reboot WellGate FXO GateWay 1. 2. 3. Confirming the values, type commit and press enter to save all the changes you have done. Type reboot and press enter to reboot the WellGate FXO GateWay. Wait for WellGate FXO GateWay initializing in gatekeeper mode. 21 WellGate FXO GateWay User Manual S/W version:x4fxo.117 3.2 Peer-to-Peer Mode Peer-to-Peer Mode allows users to call other VoIP devices without using a gatekeeper. When in Peer-To-Peer mode, WellGate FXO GateWay will send SETUP message directly to the destination IP address once the dial is finished. Users have 2 methods of dial. One is IP dialing, and the other is Phonebook dial, which we will describe later. When using IP address as destination phone number, press "*" as "." in IP address expression, and press "#" when dial is finished. When using Phonebook, users can dial predefined phone number, and press "#" (optional, to accelerate the dial) as end of dial. To configure Peer-To-Peer Mode in WellGate FXO GateWay, follow the steps below: 1. Set Peer-To-Peer Mode, using "h323" command ------------------------------------------------------------------------------------------------usr/config$ h323 ­ mode 1 Note: mode 1 is for Peer-To-Peer (non-gk) mode, while mode 0 is for GK mode. 2. Configure Phonebook, using "pbook" command. Users can refer to chapter 5.11 [pbook] command for more information. ------------------------------------------------------------------------------------------------usr/config$ pbook ­ add name TEST1 ip 10.1.1.1 e164 10 Note: the command is to add a record onto Phonebook. After the command completed, you can type "pbook ­print" to see if the input record is correct. When adding a record to Phonebook, users do not have to reboot the machine, and the record will be effective immediately. 22 WellGate 3804 User Manual 3.3 Behind IP-Sharing IP Sharing function The function is for user whose network environment is behind IP Sharing device. It is said WellGate FXO GateWay is connected to the IP Sharing device. An example such as ADSL network is in the following. ATU-R ADSL Modem WAN IP Sharing device LAN WellGate FXO GateWay LAN PC The WAN IP Address obtained from ADSL has two kinds of methods. One is fixed IP Address, while user applies for one or more fixed IP Addresses. Another is dynamic IP Address while user applies for dial-up connection way. The LAN IP Address of User's PC can be set as DHCP client in order to gain an valid one. Anther IP Address for WellGate FXO GateWay must be set as an fixed one in order for that IP Sharing device pass forwarding the relevant information from WAN to LAN. Besides, a valid IP Address which meets the IP Sharing device (LAN site) is the element. WellGate FXO GateWay must enable the IP Sharing function for the fixed / dynamic WAN IP Address. Fixed IP Address ­ usr/config$ ifaddr ­ipsharing 1 210.11.22.33 Dynamic IP Address ­usr/config$ ifaddr ­ipsharing 1 ============================================================= Please be noted With Dynamic WAN IP Address, an valid Gatekeeper for WellGate FXO GateWay to get register on it is a must. In other word, it is not workable in Peer-to-Peer mode while dynamic WAN IP Address. IP Sharing device must have a function to do IP/Port mapping. Some is named as DMZ, some is named as virtual server. The VoIP messages from WAN have to completely pass forward to the LAN. It is said if the WellGate FXO GateWay is assigned a virtual fixed IP Address such as 192.168.1.5, IP Sharing device must forward the VoIP messages to 192.168.1.5. 23 WellGate FXO GateWay User Manual S/W version:x4fxo.117 4. Disconnect Tone Configuration This application note is going to describe the procedures of configuring the disconnect tone on WellGate FXO GateWay in order to release LINE ports of WellGate FXO GateWay after PSTN/PBX caller party is hung up. 4.1 What is Disconnect Tone IP Side PSTN or PBX IP-Network WellGate PSTN side FXO GateWay Other VoIP devices Caller A caller make a telephone call to Gateway from PSTN side, WellGate FXO GateWay will answer the call automatically. If the IP side of other VoIP devices do not answer the call and the caller hang up the call, the PSTN/PBX will give Gateway a disconnect tone automatically. Or, both devices are installed with WellGate FXO GateWay and connect to local PSTN. If both parties are in talk mode, one side hang up the call the WellGate has to recognize the disconnect tone from local PSTN. The WellGate FXO GateWay gateway will recognize this disconnect tone and release the LINE port with the pre-defined busy tone or reorder tone from WellGate FXO GateWay tone table. If the other VoIP device of IP side hangs up the phone, the gateway will release the LINE port automatically without analyzing disconnect tone from PSTN/PBX. There are three parameters received from PSTN/PBX. - High level frequency and Low level frequency - Tone Cadence (ON/OFF intervals) - Tone level These parameters have to be properly configured to WellGate FXO GateWay in order to recognize disconnect tone correctly. Each different PSTN/PBX have different parameters. So, WellGate FXO GateWay has to configure tone table when LINE port connect to different PSTN/PBX. 24 WellGate 3804 User Manual 4.2 How to configure disconnect tone on WellGate FXO GateWay gateway WellGate FXO GateWay has a default setting of disconnect tone (Busy tone 1, Busy tone 2, reorder tone 1 and reorder tone 2 ). If the disconnect tone was recognized correctly, the LINE port from PSTN/PBX will be released in two seconds. Otherwise it may be released after one minute or lock this LINE permanently. The tone table parameters are shown as follows. LowFreq 480 : Low frequency is 480 HZ HighFreq 620 : High frequency is 620 HZ LowFreqLevel 8 : Low frequency level received range from PSTN/PBX HighFreqLevel 8 : High frequency level received range from PSTN/PBX TOn1 50 : Disconnect tone cadence ON time is 0.5 seconds TOff1 50 : Disconnect tone cadence OFF time is 0.5 seconds ( If this is continuous tone, the Toff has to set to 1023 ) TOn2 1023 : Disconnect tone second cycle cadence ON time is OFF TOff2 1023 : Disconnect tone second cycle cadence OFF time is OFF ( If the tone cadence has only one cycle, the second cycle must set to 1023 ) (1) Examples how to configure Tone table a. 480/620 frequency with ON/OFF time is 0.5 seconds tone -busy1 480 620 8 8 50 50 1023 1023 b. 480 HZ single frequency with continuous tone tone ­reorder2 480 0 8 0 50 1023 1023 1023 (2) There are two ways to analyze the disconnect tone. a. The first one is using command "greetrd" from WellGate FXO GateWay. Once you follow the instruction to analyze the disconnect tone, Gateway will configure the tone table (Busy tone 1, Busy tone 2, reorder tone 1 and reorder tone 2 ) with proper frequency and default tone level and cadence (Ton1/Toff1) automatically. Or you may read the analysis tone frequency from command line and configure to one of tone table manually. The default tone level is set to 8. And the tone cadence (Ton1/Toff1) is set to four different values on tone table. They are 0.1 second, 0.25 seconds, 0.5 seconds and 0.75 seconds with parameters 10/10, 25/25, 50/50 and 75/75. If the PBX/PSTN cadence is not the value as default shown as above, you need to use the following instruction to analyze ON/OFF intervals. b. You may use your PC (START Program Files Accessories Multimedia Recorder) with Headset or Microphone to record the disconnect tone via a telephone set from PSTN/PBX and save to a voice file. Then you can use "CoolEdit Pro" software to analyze the frequency and ON/OFF time. Please visit http://www.cooledit.com to download demo version for analysis. You can use this program to analyze ON/OFF time and fill in to tone table. 25 WellGate FXO GateWay User Manual S/W version:x4fxo.117 4.3 Adjust Tone Table parameters manually If the gateway still cannot release the LINE port in two seconds, try to adjust the frequency by 1 hz on tone table. For example, your analysis value is 620/480, take the following procedures. 620/479 620/480 620/481 621/479 621/480 621/481 619/479 619/480 619/481 If the LINE port of gateway was locked, please use "hangup 0" command to release LINE 1, "hanhup 1" to release LINE 2...etc. 4.4 Adjust Input Tone Level Sometimes the disconnect tone level is too low to be detected by WellGate FXO GateWay. You can increase input gain from the following command. voice -volume input xx commit reboot xy is the input gain parameters. The maximum number is 35. if the number is over 35, the echo may be happened. Once you increase input gain, the voice volume from PSTN to IP side is increased too. 26 WellGate 3804 User Manual 5. Command lists 5.1 [help] command Type help or man or ? to list all the available command. usr/config$ ? help quit debug reboot flash commit ifaddr time ping greetrd pbook sysconf h323 voice gk tos tone support group bureau prefix rom passwd help/man/? [command] quit/exit/close show debug message reboot local machine clean configuration from flash rom commit flash rom data internet address manipulation show current time test that a remote host is reachable Greeting voice and Disconnect tone Record mode Phonebook information and configuration System information manipulation H.323 information manipulation Voice information manipulation H.323 gatekeeper manipulation IP Packet ToS (Type of Service)values Setup of call progress tones Special Voice function support manipulation Grouping setting information and configuration Bureau line information manipulation Prefix information manipulation ROM file update Password setting information and configuration usage: help [command] 5.2 [quit] command Type quit will quit the WellGate FXO GateWay configuration mode. And turn back to login prompt. usr/config$ quit Disconnecting... login: 27 WellGate FXO GateWay User Manual S/W version:x4fxo.117 Note: It is recommended that type the "quit" command before you leave the console. If so, WellGate FXO GateWay will ask password again when next user connects to console port. 5.3 [debug] command Open debug message will show up specific information while WellGate FXO GateWay is in operation. After executing the debug command, it should execute command debug -open as well. One example is demonstrated below. usr/config$ debug -add h323 vp usr/config$ debug -open Parameters Usage: -status Display the enabled debug flags. -add Add debug flag. -- h323 : h323 related information -- vp : voice related information -delete Remove specified debug flag. -open Start to show debug messages. -close Stop showing debug messages. 5.4 [reboot] command After commit command, type reboot to reload WellGate FXO GateWay in new configuration. The procedure is as below: usr/config$ reboot Attached TCP/IP interface to cpm unit 0 Attaching interface lo0...done AC4804[0] is OK AC4804[1] is OK AC4804[2] is OK Successful Initialize OSS libraries...OK! open stack successful cmInitialize succeed! GK mode selected. login: 28 WellGate 3804 User Manual 5.5 [flash] command This command will clean the configuration stored in the flash rom and reboot WellGate FXO GateWay in factory default setting. Parameter Usage: -clean clean all the user-defined value, and reboot WellGate FXO GateWay in factory default mode. Note: It is recommended that use "flash ­clean" after application firmware id upgraded. Warning: Once users execute flash ­clean, all the configurations of WellGate FXO GateWay will be cleaned. This can only be executed by user who log in with root 5.6 [commit] command Save changes after configuring the WellGate FXO GateWay. ------------------------------------------------------------------------------------------------usr/config$ commit This may take a few seconds, please wait.... Commit to flash memory ok! usr/config$ Note: Users should use commit to save modified value, or they will not be activated after system reboot. 5.7 [ifaddr] command Configure and display WellGate FXO GateWay network information. usr/config$ ifaddr LAN information and configuration Usage: ifaddr [-print]|[-dhcp used]|[-sntp mode [server]] ifaddr [-ipsharing used [deviceAddr]][-cmcenter ip address] ifaddr [-ip ipaddress] [-mask subnetmask] [-gate defaultgateway] -print -ip -mask -gate -dhcp -sntp -http -DNS Display LAN information and configuration. Specify ip address. Set Internet subnet mask. Specify default gateway ip address Set DHCP client service flag (On/Off). Set SNTP server mode and specify IP address. Set HTTP server port. Set DNS sever IP address 29 WellGate FXO GateWay User Manual S/W version:x4fxo.117 -timezone Set local timezone. -cmcenter Set Management Center IP Address. -ipsharing Specify usage of an IP sharing device and specify IP address. Note: Range of ip address setting (0.0.0.0 ~ 255.255.255.255). DHCP client setting value (On=1, Off=0). If DHCP set to 'On', Obtain a set of Internet configuration from DHCP server assgined. SNTP mode (0=no update, 1=specify server IP, 2=broadcast mode). Example: ifaddr -ip 210.59.163.202 -mask 255.255.255.0 -gate 210.59.163.254 ifaddr -dhcp 1 ifaddr -sntp 1 210.59.163.254 ifaddr -ipsharing 1 210.59.163.254 ifaddr -timezone 8 ifaddr -dns primary secondary usr/config$ Parameters Usage: -print print current IP setting -ip assigned IP address for WellGate FXO GateWay -mask internet subnet mask -gate IP default gateway -dhcp Dynamic Host Configuration (1 = ON; 0 = OFF) -sntp Simple Network Time Protocol (1 = ON; 0 = OFF) When SNTP function is activated, users have to specify a SNTP server as network time source. An example is demonstrated below: ------------------------------------------------------------------------------------------------usr/config$ ifaddr -sntp 1 10.1.1.1 while 10.1.1.1 stands for SNTP server's IP address. -http -dns Change http port. User can change default HTTP port(80) to another one for security or NAT application. Set DNS server IP address. User can set one or two sets of DNS server. (ifaddr ­dns 1 "primary DNS server IP address" ; ifaddr ­dns 2 "secondary DNS server IP address") Set timezone for WellGate FXO GateWay. User can set different time zone according to the location WellGate FXO GateWay is. For example, in Taiwan the time zone should be set as 8,which means GMT+8. Set management center IP address. IF user specifies management center IP address, WellGate FXO GateWay will send information to management center, let user can easily -timezone -cmcenter 30 WellGate 3804 User Manual configure via management center interface. (sysconf ­cmcenter "IP address of management center") Note: management center is optional software to help user can easily configure WellTech products, please contact your reseller to know more about it. -ipsharing Specify usage of an IP sharing device and specify IP address. If WellGate FXO GateWay is behind a IP-sharing , user can enable IP sharing function and specify public IP address of IP-sharing. 5.8 [time] command When SNTP function of WellGate FXO GateWay is enabled and SNTP server can be found as well, type time command to show current network time. ------------------------------------------------------------------------------------------------usr/config$ time Current time is THU JAN 01 05:29:23 1970 5.9 [ping] command Use ping to test whether a specific IP is reachable or not. For example: if 192.168.1.2 is not existing while 210.63.15.32 exists. Users will have the following results: usr/config$ ping 210.54.23.129 PING 210.54.23.129: 56 data bytes no answer from 210.54.23.129 usr/config$ ping 192.168.4.121 PING 192.168.4.121: 56 data bytes 64 bytes from 192.168.4.121: icmp_seq=0. time=5. ms 64 bytes from 192.168.4.121: icmp_seq=1. time=0. ms 64 bytes from 192.168.4.121: icmp_seq=2. time=0. ms 64 bytes from 192.168.4.121: icmp_seq=3. time=0. ms ----192.168.4.121 PING Statistics---4 packets transmitted, 4 packets received, 0% packet loss round-trip (ms) min/avg/max = 0/1/5 31 WellGate FXO GateWay User Manual S/W version:x4fxo.117 5.10 [greetrd] command This command is for user to record their own greeting and analyze disconnect tone. If WellGate FXO GateWay can't hang up call and release line correctly, please use this function to analyze disconnect tone of PSTN side. 1. Greeting Voice Record : please follow instructions on screen ; first, call in line1 of WellGate FXO GateWay from PSTN side(now can't hear greeting) and press "enter" to start record .After finishing recording, please press "enter" again to stop recording. Then choose "y/n" to replay and save or not. ------------------------------------------------------------------------------------------------------------usr/config$ greetrd ================================================== Welcome to Voice Record/Analysis Mode -------------------------------------------------1.Greeting Voice Record. 2.Disconnect Tone Analysis. 3.exit. -------------------------------------------------Please input function(1~3): 1 1.Greeting Voice Record. Please Dial-in "Line 1" and press "Enter" to start record!!! Press "Enter" to stop record!!! Starting record... Stoped record!!! New Greeting Voice Infomation --------------------------------------File size : 0 (K bytes) 8 (seconds) Totally time: Do not Hang up the phone!! Please wait for Writing...block 0 32 WellGate 3804 User Manual Please wait for Writing...block 1 Please wait for Writing...block 2 Replay New Greeting Voice?(y/n): 2. Disconnect Tone Analysis : please follow instructions on screen ; first call in line1 of WellGate FXO GateWay from PSTN side(now can't hear greeting), hang up the phone and press "enter" to start record disconnect tone. Finally, choose "y/n" to save data analyzed or not. Notice that system will save one set of frequency analyzed and 4 set different on/off time in "busytone1","busytone2" ," reordertone1" , "reordertone2" (Please refer to tone command) . If WellGate FXO GateWay still can't hang up call correctly, it could be tone cadence issue (on/off time). Please count on/off time and configure it into tone command. ------------------------------------------------------------------------------------------------------------usr/config$ greetrd ================================================== Welcome to Voice Record/Analysis Mode -------------------------------------------------1.Greeting Voice Record. 2.Disconnect Tone Analysis. 3.exit. -------------------------------------------------Please input function(1~3): 2 2.Disconnect Tone Analysis. Please Dial-in "Line 1" and then Hang up the phone!!! Press "Enter" to start record!!! Waiting for Disconnect Tone from PSTN.... Disconnect Tone Detected.... Starting Record... Set parameters to flash? (Y/N) 33 WellGate FXO GateWay User Manual S/W version:x4fxo.117 3. exit : exit this command ------------------------------------------------------------------------------------------------------------usr/config$ greetrd ================================================== Welcome to Voice Record/Analysis Mode -------------------------------------------------1.Greeting Voice Record. 2.Disconnect Tone Analysis. 3.exit. -------------------------------------------------Please input function(1~3): 3 Are you sure to EXIT?!(y/n): y usr/config$ 5.11 [pbook] command Phone Book function allows users to define their own numbers, which mapping to real IP address. It is effective only in peer-to-peer mode. When adding a record to Phone Book, users do not have to reboot the machine, and the record will be effective immediately. ------------------------------------------------------------------------------------------------usr/config$ pbook Phonebook information and configuration Usage: pbook [-print [start_record] [end_record]] pbook [-add [ip ipaddress] [name Alias] [e164 phonenumber]] pbook [-search [ip ipaddress] [name Alias] [e164 phonenumber]] pbook [-insert [index] [ip ipaddress] [name Alias] [e164 phonenumber]] pbook [-delete index] pbook [-modify [index] [ip ipaddress] [name Alias] [e164 phonenumber]] -print -add Display Phonebook data. Add an record to Phonebook. 34 WellGate 3804 User Manual -search -delete -insert -modify Note: Search an record in Phonebook. Delete an record from Phonebook. Insert an record to Phonebook in specified position. Modify an exist record. If parameter 'end_record' is omited, only record 'start_record' will be display. If both parameters 'end_record' and 'start_record' are omited, all records will be display. Range of ip address setting (0.0.0.0 ~ 255.255.255.255). Range of index setting value (1~100), Example: pbook -print 1 10 pbook -print 1 pbook -print pbook -add name Test ip 210.59.163.202 e164 1001 pbook -insert 3 name Test ip 210.59.163.202 e164 1001 pbook -delete 3 pbook -search ip 192.168.4.99 pbook -modify 3 name Test ip 210.59.163.202 e164 1001 Parameter Usages: -print print out current contents of Phone Book. Users can also add index number, from 1 to 100, to the parameter to show specific phone number. Note: means the sequence number in phone book. If users do request a specific index number in phone book, WellGate FXO GateWay will give each record a automatic sequence number as index. -add -search -delete -insert -modify add a new record to phone book. When adding a record, users have to specify name, ip, and e164 number to complete the command. search a record in phone book. The searching criteria can be name, ip, or e164. delete a specific record. "pbook ­delete 3" means delete index 3 record. add a new record and force to assign a specific index number for it. modify an existing record. When using this command, users have to specify the record's index number, and then make the change. Phonebook Rules: To meet the requirements of communicating with trunk gateway or other applications, Phonebook has following characteristics to be noticed. When the destination side is a terminal, for ex: IP Phone or soft phone, e164 number stands for exact destination phone number. 35 WellGate FXO GateWay User Manual S/W version:x4fxo.117 When the destination side is a gateway, for ex: T1/E1 gateway, e164 phone number stands only for gateway prefix. That is to say, users have to continue to dial destination number, following the prefix number. A example is as below: A WellGate FXO GateWay In Phonebook, there's a record : Index Name IP E164 1 B_gateway 192.168.1.2 0 ------------------------------------------------------------------------------------------B E1 trunk gateway, which connects to PSTN with E1 PRI. If users want to make a call to PSTN number "82265699", they have to pickup one of the phone connected to WellGate FXO GateWay, and then dial "082265699". After receiving the complete dialed number, WellGate FXO GateWay will search for its Phone Book, find "0" as matched prefix, and then dial out to B's IP address directly with destination e.164 (phone number) "82265699". Pleased be noted that "0" is eliminated from WellGate FXO GateWay itself. Note:1. Because of above characteristics, users have to take care of the number plan very well to avoid the numbering conflict. If users already defined "0" for specific trunk gateway, other terminal started with "0" shall be avoided, or the number will be routed to the trunk gateway defined "0". 2. If user wants to set 2 sets of similar e164 such as 123 and 1234, please be careful configure 123 first, or it may cause problem when user dial 1234, WellGate FXO GateWay may dials out IP address of 123. 3. (1) If called party is FXO product, please set e164 of pbook as e.164 of called party, and remember to set sysconf ­drule in_drop "e.164"(refer to 5.12.)in called party. (2) If called party is FXS product, please set e164 of pbook as prefix of called party, when dialing to different line of FXS product, please dial line number. 5.12 [pppoe] Display PPPoE related information. --------------------------------------------------------------------------------------------------PPPoE device information and configuration Usage: pppoe [-print]|[-open]|[-close] pppoe [-dev on/off][-id username][-pwd password] -print Display PPPoE device information. -dev Enable(=1) or Disable(=0) device. -open Open PPPoE connection. -close Disconnect PPPoE connection. -id Connection user name. -pwd Connection password. -reboot Reboot after remote host disconnection. --------------------------------------------------------------------------------------------------Paremeter Usage: -print print PPPoE status. -dev Enable PPPoE Dial-up function 36 WellGate 3804 User Manual -open -close -id -pwd -reboot Open the connection Close the connection Input the User name ID provided by ISP Input the User name password provided by ISP Reboot the PPPoE connection. 5.13 [sysconf] command This command displays the system information and configuration. ------------------------------------------------------------------------------------------------usr/config$ sysconf System information and configuration Usage: sysconf [-service type] [-plan digits] [-2nddial flag] [-keypad dtmf] [-ringdet method] [-callalive flag] [-port s1 s2 s3 s4 ] [-seizure mode] [-2nddial switch] [-drule [in_filter str1] [in_drop str2] [in_insert str3] [out_filter str4] [out_drop str5] [out_insert str6]] [-askpin f] [-pincode [set1 pin1] [set2 pin2] [set3 pin3] [set4 pin4]] sysconf -print -print -service Display system overall information and configuration. Specify gateway service type. (0: Dial in service, 1: Direct in service (2: HotLine/LineToLine 3: Transient service.) -ringdet -plan -port -idto -eod -seizure -2nddial Specify gateway ring detect method. (0:For 1st hardware version, 1:For 2st hardware version. Number of digits for dial plan. (any positive number.) Enable/Disable individual port. The duration of two pressed digits in dial mode Digit type of end of dialing. ( 0:No end of dialing, 1:[*] button, 2:[#] button ) Choose line seizure mode (None/UCD). Config GW to accept 2nd dtmf set. In this mode, device from IP side needs to dial GW's E164, wait for PSTN dialtone, and then dial out. -drule Specify digits to be filtered/dropped/inserted before making an outgoing IP call or after receving an incoming 37 WellGate FXO GateWay User Manual S/W version:x4fxo.117 IP call. -askpin -ring -keypad -pincode -cid -faxrdd Note: Use character 'x' to delete the drule parameter. For line seizure 0: None, 1: UCD. For askpin: f=0: No, f=1: Yes, f=2: per channel Hotline feature should be used together with: $sysconf -2nddial 0 (2nddial off) $h323 -mode 1 (peer-to-peer mode) for Hotline/LineToLine table configuration. $bureau -print PIN code prompt before greeting. 0:Disable 1:Per Unit 2:Per Channel. Ring number before answer. 0:Disable, other is number of ring ( 1 ~ 5 ). DTMF setting: 0=In-band, 1=H.245 Alphanumeric, 2=H.245 SignalType, 3=Q.931 UserInfo. , 4=RFC2833. Specify PIN codes. Specify caller id type.(0:diable 1: Bellcore) FAX redundancy depth.(0 ~ 2) LineToLine feature should be used together with: $sysconf -2nddial 1 (2nddial on) $h323 Example: sysconf -service 0 -plan 4 -port 1 1 1 1 0 0 sysconf -callalive 0 -keypad 0 sysconf -2nddial 0 -drule out_filter 002 in_insert x in_drop 1 sysconf -askpin 1 -pincode set1 12345 usr/config$ -mode 1 (peer-to-peer mode) for Hotline/LineToLine table configuration. $bureau -print - service: 0 Dial In Service in Dial In Service, WellGate FXO GateWay will pick up incoming calls from PSTN, play pre-recorded voice greeting or, and then have users to make a 2nd dial to destination. 1/2 HotLine Service (this feature must be implemented after set bureau ­table command) HotLine Service provides Hot Line function, which connects directly to pre-defined destination. For ex: if L1 of WellGate FXO GateWay is assigned to destination address 192.168.1.12 in Hot Line Mode. 38 WellGate 3804 User Manual When users from PSTN make a call to L1 of WellGate FXO GateWay, it will directly connect to 192.168.1.12 without a 2nd dial. Note: In hotline service, must set WellGate FXO GateWay sysconf ­2nddial 0 . LineToLine Service is like HotLine Service, but ask for a specific line number. For ex: if L1 of WellGate FXO GateWay is assigned to destination address 192.168.1.12 /Line4 in LineToLine Mode. When users from PSTN make a call to L1 of WellGate FXO GateWay, it will directly connect to 192.168.1.12 and choose Line4 to call out to PSTN. This is mostly applied to ITSP, who provides international VoIP solution. Note: In LineToLine service, must set WellGate FXO GateWay sysconf ­2nddial 1 . 1 Transient service. If an call from IP to PSTN for landing (dial to PSTN phone), the IP side connection will be established only when an tip/ring polarity reversal was detected by FXO gateway. This service type must used in GK mode, fast start enabled on both endpoints. -2nddial off and use ­drule command to drop the number of FXO itself. - ringdet: to define ring detection method. (0 is for old hardware version; 1 for new hardware version) - plan: It is for setting dial-numbering plan. While e164 number is three digits, the plan should be set as 3 or 0. The plan 0 is for any positive digits use. - port: This command can enable or disable individual port. The default value is set to enable all ports. - idto: The duration of two pressed digits in dial mode - eod: Digit type of end of dialing. ( 0:No end of dialing, 1:[*] button, 2:[#]button ) - seizure: line seizure mode. None (0) when calling from IP side, choose L1 every time if it is available. UCD (1) when calls from IP side, choose L1 for the first time, and L2 for the 2nd time, (cyclic) Note: Do not enable this function together with group (please refer to 5.18). - 2nddial: This command is necessary for setting one time dial method use. While user would like to skip 2nddial process, WellGate FXO GateWay must close 2nddial and set as 0 (2nddial off). The default value is set as 1 (2nddial on). - drule: This command only works while 2nddial is off. When user would like to make an outgoing call or receive an incoming call shortly, it is necessary to set the following three commands belonged to drule. drop: drop the dial digit. insert: insert the dial digit filter: filter the dial digit. 39 WellGate FXO GateWay User Manual S/W version:x4fxo.117 Note: 1. out: Through WellGate FXO GateWay to dial out to another Gateway's e164 number. When making an outgoing call, it is necessary to set three commands in order, filter, insert then drop. Example: sysconf ­drule out_filter 002886 out_insert 0 out_drop 02 2. in: Through pass WellGate FXO GateWay in order to connect with PSTN / PBX side. When making an incoming call from other Gateway, the three commands is necessary to be set in order, drop, insert, then filter. Example: sysconf ­drule in_drop 002886 in_insert 0 in_filter 02 3. 3. While the specified digit would like to be deleted, use the character x instead of any digits have configured. -askpin: 0 disables ASKPIN function 1 enables ASKPIN function, and apply to the whole unit. Every channel uses the same PINCODE. 2. enables ASKPIN function, and apply to each channel respectively. Every channel uses a different pincode. -ring: To set when dial in WellGate FXO GateWay from PSTN side, WellGate FXO GateWay will pick the call immediately or rings for specific times before picks up. 0 disable: pick up immediately 1-5 times of ring before WellGate FXO GateWay picks up. - keypad: keypad type when relay DTMF signal. 0 In-Band 1 h.245 alphanumeric 2 h.245 signal type 3 q.931 user info 4 RFC2833. - pincode: to specify 2 sets of pincode. - cid : to disable or enable Bellcore format caller ID. If user enables this function, gateway will receive caller ID and pass it through. (Note: only FSK type of caller ID is available.) - faxrdd: To add the redundancy depth in fax when the network is not in a good quality. (sysconf -faxrdd 2 ;0:default / 1:first level in depth / 2:highest level in depth) Note: It's will take more bandwidth if the depth level is the highest in 2. 5.14 [h323] command This command is to configure H.323 related parameters. ------------------------------------------------------------------------------------------------ 40 WellGate 3804 User Manual usr/config$ h323 H.323 stack information and configuration Usage: h323 h323 [-gk ipaddress] [-multicast used] [-e164 number] [-alias h323id] [-rtp port] [-h245 port] [-ttl time] [-gkfind port] [-ras port] [-range [start num1] [end num2]] h323 -print -print -mode -gk -gkname -dfgw -e164 -alias -gkdis -rtp -h225 -q931 -ttl -gkfind -gwtype -ras -range -respto -connto Note: H.245 port configuration is not available now. Options -gk -e164 -alias -multi -ttl -gkfind -ras are ignored when RAS mode is configured as Peer-to-Peer mode. Example: h323 -gk 210.59.163.171 -e164 0 -alias fxo h323 -mode 1 Display H.323 stack information and configuration. Configure as Gatekeeper mode or Peer-to-Peer mode. Gatekeeper ip address. (0.0.0.0 ~ 255.255.255.255) Gatekeeper ID Default Gateway ip address. (0.0.0.0 ~ 255.255.255.255) IP side registered number (phone number). IP side registered H.323 alias (account name). Gatekeeper auto discovery (On=1, Off=0). RTP port number (1024~65532). H225 RAS port number (N/A). H225 Signal port number (N/A). RAS TTL time (0~3600 second). Gatekeeper finding port (1024~65535). Register as Gateway (1) or Terminal (0) type Gatekeeper RAS port (1024~65535). Dynamically allocated port range (1024~65535). Max waiting time for 1st response to a new call (1~200). Max waiting time for call establishment after receiving 1st response of a new call (1~20000). Parameters Usage: -print print current h323 related settings -mode alternatives for gatekeeper or peer-to-peer mode (0=gatekeeper mode; 1=peer-to-peer mode). If users select gatekeeper mode, a extra gatekeeper is need when WellGate FXO GateWay is in operation. 41 WellGate FXO GateWay User Manual S/W version:x4fxo.117 -gk -gkname -dfgw to assign gatekeeper's IP address when WellGate FXO GateWay is in gatekeeper mode. to assign Gatekeeper ID when WellGate FXO GateWay is in gatekeeper mode. to set IP address of default gateway, this function is the same as Microsoft NetMeeting. A.To implement this feature both endpoints must be under peer-to-peer mode. B.If the other endpoint is FXO products, such as WellGate 38xx, which have to set as sysconf ­2nddial 0 to make one-stage dialing. From PSTN side dial in WellGate FXO GateWay, when hearing greeting user can dial remote PSTN number under default gateway, WellGate FXO GateWay will automatically dial to default gateway, then default gateway will dial this number to PSTN side. For example, user wants to dial from WellGate FXO GateWay A to ext.888 under WellGate FXO GateWay B, user only have to dial 888 after hearing greeting of WellGate FXO GateWay . C.If the other endpoint is FXS products such as WellGate 35xx : From PSTN side dial in WellGate FXO GateWay, when hearing greeting user can dial line number of WellGate 35xx. For example ,user wants to dial from WellGate FXO GateWay to WellGate 3502 the configuration of 3502 is h323 ­line1 101 ­line2 102user can press 101 or 102 dialing to line1 or line2 of WellGate 3502 after hearing greeting of WellGate FXO GateWay. -e164 -alias -gkdis -rtp -h225 -q931 -ttl -gkfind -gwtype e164 number, which is registered as phone number in gatekeeper. h323 ID, a identification in h323 world for other parties' recognition. The field might be used as a key of authorization or accounting in some VoIP application. It is recommended to assign a special name, or it might conflict with other devices. Switch ON or OFF gatekeeper discovery function (1 = ON; 0 = OFF). When it's ON, WellGate FXO GateWay will send GRQ with GK ID to default gatekeeper. If the GK ID didn't matched, GW will send GRQ with GK ID in multicast. to allocate RTP port range--NOT RECOMMENDED. This may be used when RTP port range conflicts with Firewall policy. Configure H225 RAS port number manually.(N/A). Configure H225 Signal port number manually.(N/A). to set timer for TTL(Time To Live). WellGate FXO GateWay would send RRQ, with keepAlive, to gatekeeper periodically according to TTL timer. gatekeeper finding port. Port number, which WellGate FXO GateWay uses it to discover a gatekeeper. Default value is 1718. to set WellGate FXO GateWay register mode as terminal or 42 WellGate 3804 User Manual -ras -range -respto -connto gateway,0 as terminal 1 as gateway. Please notice that if set WellGate FXO GateWay as terminal mode, must set sysconf ­2nddial 1(refer to 5.12). to set default gatekeeper RAS port number. Default value, 1719, is well-known port for RAS communication. to allocate dynamic port range, which WellGate FXO GateWay might be using. response timeout. Max waiting time for 1st response to a new call (1~200). connection timeout. Max waiting time for call establishment after receiving 1st response of a new call (1~20000). 5.15 [voice] command The voice command is associated with the audio setting information. There are four voice codecs (g.729a optional) supported by WellGate FXO GateWay. -----------------------------------------------------------------------------------------------Voice codec setting information and configuration Usage: voice [-send [G723 ms] [G711A ms] [G711U ms] [G729A ms] [G729 ms] ] [-volume [voice level] [input level] [dtmf level]] [-nscng G723 used] [-echo used] [-mindelay used] [-maxdelay used] voice -print voice -priority [G723] [G711A] [G711U] [G729A] [G729] -print -send Display voice codec information and configuration. Specify sending packet size. G.723 (30/60 ms) G.711A (20/40/60 ms) G.711U (20/40/60 ms) G.729A (20/40/60 ms) G.729 (20/40/60 ms) -priority Priority preference of installed codecs. G.723 G.711A G.711U G.729A G.729 -volume Specify the following levels: 43 WellGate FXO GateWay User Manual S/W version:x4fxo.117 voice volume (0~63, default: 32), input gain (0~63, default: 32), dtmf volume (0~31, default: 27), -nscng -echo No sound compression and CNG. (G.723.1 only, On=1, Off=0). Setting of echo canceller. (On=1, Off=0, per port basis). -mindelay Setting of jitter buffer min delay. (0~150, default: 100). -maxdelay Setting of jitter buffer max delay. (0~150, default: 150). Example: voice -send g723 60 g711a 60 g711u 60 g729a 60 g729 60 voice -volume voice 20 input 32 dtmf 27 voice -echo 1 1 1 1 1 1 usr/config$ Parameters Usage: -print print current voice information and configurations. -send to define packet size for each codec. 20/40/60ms means to send a voice packet per 20/40/60 milliseconds. The smaller the packet size, the shorter the delay time. If network is in good condition, smaller sending packet size is recommended. In this parameter, 20/40/60ms is applicable to G.711u/a law, and G.729a codec, while 30/60/90ms is applicable to G.723.1 codec. -priority codec priority while negotiating with other h323 device. This parameter determines the listed sequence in h.245 TCS message. The codec listed in left side has the highest priority when both parties determining final codec. -volume There are three adjustable value. voice volume stands for volume, which can be heard from WellGate FXO GateWay side; input gain stands for volume, which the opposite party hears. dtmf volume stands for DTMF volume/level, which sends to its own Line1 or Line2. -nscng silence suppression and comfort noise generation setting (1 = ON; 0 = OFF). It is applicable to G.723 codec only. An example is demonstrated below: ------------------------------------------------------------------------------------------------usr/config$ voice -nscng g723 1 -mindelay the minimum jitter buffer size. (Default value= 90 ms) -maxdelay the minimum jitter buffer size. (Default value= 150 ms) ------------------------------------------------------------------------------------------------usr/config$ voice ­ mindelay 90 ­ maxdelay 150 -optfacor 7 -echo activate each canceller (1 = ON; 0 = OFF). Note: be sure to know well the application before you change voice parameters because this might cause incompatibility. 44 WellGate 3804 User Manual 5.16 [tos] command TOS service allows users to achieve QoS on IP network. ------------------------------------------------------------------------------------------------usr/config$ tos IP Packet ToS(type of Service)/Differentiated Service configuration Usage: tos [-rtptype dscp] tos [-sigtype dscp] tos -print Example: tos -rtptype 7 -sigtype 0 usr/config$ Parameter Usages: -print : display current TOS values configurations. -sigtype configure DSCP value of signaling packets from 0 to 63 -rtptype configure DSCP value of RTP packets from 0 to 63 Note: 1. Users should be aware that TOS is effective only when network devices (for ex: router, switch.. etc.) support TOS. 2. tos -rtptype 14 -sigtype 10 is top priority of package. 5.17 [tone] command Tone detection of WellGate FXO GateWay is configurable if the bureau line is connected to PABX or PSTN. Users can refer to "greetrd" command for tone recording and analysis. Sometimes the frequencies might shift from standard level. In such a situation, users have to adjust the tone value manually using this command. ------------------------------------------------------------------------------------------------usr/config$ tone Setup of call progress tones Usage: 45 WellGate FXO GateWay User Manual S/W version:x4fxo.117 tone -toneX LowFreq HighFreq LowFreqLevel HighFreqLevel TOn1 TOff1 TOn2 TOff2 tone -print Note: toneX has the following possibility: busy1 busy2 reorder1 reorder2 ringtone1 ringtone2 dialtone Example: tone -busy1 400 0 8 0 50 50 0 0 tone -dialtone 400 0 19 0 25 25 0 0 5.18 [support] command This command provides some extra functions that might be needed by users. ----------------------------------------------------------------------------------------------------usr/config$ support Special Voice function support manipulation Usage: support[-tunnel enable] support -print -t38 -t38ecm -fstart -tunnel -h245fs Example: support -t38 1 support -t38ecm 1 support -fstart 1 support -tunnel 0 support -h245fs 1 usr/config$ T.38(FAX) enabled/disabled. T.38(FAX) ECM enabled/disabled. Fast start enabled/disabled. H245 Tunneling enabled/disabled. H245 seperate channel after faststart. Parameter Usages: -print print current setting in support command. -t38 to switch ON/OFF (1 = ON; 0 = OFF) T.38 function.T.38 function is for FAX. If user will use FAX machines, please switch on T.38 function. -t38ecm to disable/enable T.38 error correction mode. This mode 46 WellGate 3804 User Manual -fstart -tunnel -h245fs support error correction during fax high-speed mode. to switch ON/OFF (1 = ON; 0 = OFF) FastStart function. Fast Start function can shorten the connection time if the opposite party also support FastStart. to switch ON/OFF (1 = ON; 0 = OFF) H.245 tunneling function. If the function is ON, WellGate FXO GateWay will send H.245 (Call Control messages) via H.225's (Call Signal messages) link. The function is effective only when both side support h245 tunnel. to set if open H.245 separate channel after fast start or not. (1 = ON; 0 = OFF) Note: 1. it is not recommended to change the value in this command, only if users do know well the application. This might cause incompatibility with other devices. 2. If user wants to use T.38 fax under fast start mode, please make sure "h245fs" function is enabled, or fax can't work normally. 5.19 [group] command This command is for grouping 4 ports of WellGate FXO GateWay. If users need to register at least 2 numbers separately to gatekeeper, then this command is needed for such an application. ------------------------------------------------------------------------------------------------usr/config$ group PSTN side grouping information and configuration Usage: group -print | -enable | -disable | -number group_number -pattern pattern_numbers -e164 e164_numbers | -pattern pattern_numbers -e164 e164_numbers | -e164 e164_numbers Comment: -print -enable -disable -number -pattern -e164 Example: : Print current group configuration : Enable PSTN Grouping : Disable PSTN Grouping : Set number of divided groups : Set number of members in each group : Set E.164 number for each group 47 WellGate FXO GateWay User Manual S/W version:x4fxo.117 group -print group -enable group -disable group -number 2 -pattern 3 3 -e164 01 02 group -pattern 3 1 -e164 100 200 group -e164 11 22 Parameter Usages: - print : display current grouping information - enable : enable grouping function - disable : disable grouping function - number : set how many groups will be divided - pattern : set how many members in each group - e164 : set e164 of each group For ex: if users need to divide WellGate FXO GateWay into L1 in the 1st group, and L2 in the 2nd group), and have them register to gatekeeper separately (e164=100 for 1st group; e164=200 for 2nd group). They have to use the following command: ------------------------------------------------------------------------------------------------usr/config$ group ­ pattern 1 3 ­ e164 100 200 Note: GROUP function is effective only in gatekeeper mode. 5.20 [bureau] command Type bureau to display the command usage. ------------------------------------------------------------------------------------------------usr/config$ bureau Bureau line setting information and configuration Usage: bureau [-pstn number] [-hold used] [-hotline [Port DestIP TELnum]] bureau -print -print -pstn Display Bureau line information and configuration. PSTN number (per port basis). This number is used to display as a caller ID when the caller ID is not available. The maximum digit length is 32. -hold Specify the hold tone generation (using PCM file). (On/Off) Setting value (On=1, Off=0). 48 WellGate 3804 User Manual -table Note: Set Hot line/Line To Line information. (Port range: 1~6) Hotline feature should be used together with: $sysconf -service 2 (HotLine service) $sysconf -2nddial 0 (2nddial off) $h323 -mode 1 (peer-to-peer mode) Line To Line feature should be used together with: $sysconf -service 2 (HotLine service/Line To Line ) $sysconf -2nddial 1 (2nddial on) $h323 Example: bureau -pstn 2011 2012 2013 2014 2015 2016 bureau -hotline 1 192.168.4.69 628 2 192.168.4.200 999 usr/config$ -mode 1 (peer-to-peer mode) Parameter Usages: - print: display bureau line information and configuration. ------------------------------------------------------------------------------------------------usr/config$ bureau -print Bureau line setting relate information PSTN number : 2011 2012 2013 2014 2015 2016 Hold tone generation : On Hot line / Line to Line table ===================================================== Port 1 2 Destination Address 192.168.4.69 192.168.4.69 Remote TEL/CHANNEL 628 628 -------------------------------------------------------------------------------------------------- ====================================================== - pstn: PSTN number (per port basis). This number is used to display as a caller ID when the caller ID is not available. The maximum digit length is 32. - hold: while the terminals support H.450 hold function, the WellGate FXO GateWay will play the hold tone to PSTN side. - table: Set Hot line/LineToLine destination IP and e164 numbers information. - hotline : the same function with table command. Note: 1. HotLine and LineToLine functions are using the same table. 2.In HotLine service, user have to set No. prepared to dial out; in LineToLine 49 WellGate FXO GateWay User Manual S/W version:x4fxo.117 service ,user have to set port No. For example, if user set bureau ­table 1 192.168.4.69 628 in hotline service, after user dial in WellGate FXO GateWay port 1, WellGate FXO GateWay will direct dial to 192.168.4.69 and dial 628 to PSTN side, then Phone 628 will ring, user will hear ring back tone. If user set bureau ­table 1 192.168.4.69 1 in LineToLine service, after user dial in WellGate FXO GateWay port 1 , WellGate FXO GateWay will direct dial to 192.168.4.69 port 1,user will hear dial tone, then user can dial out No. to PSTN side. 5.21 [prefix] command This function can do digits replacement of incoming call from IP side or PSTN side. -----------------------------------------------------------------------------------------------usr/config$ prefix Prefix setting information and configuration Usage: prefix [-pstnrule index oldnumber newnumber (index = 1 ~ 6)] [-iprule index oldnumber newnumber (index = 1 ~ 6)] prefix -print -print -pstnrule -iprule Example: prefix -pstnrule 1 2 8862 : prefix 2 will be replaced with 8862 Display prefix information and configuration. Set PSTN incoming prefix rule information. Set IP incoming prefix rule information. Parameter Usages: -print print current setting in prefix command. -pstnrule to do digit replacement of incoming call from PSTN side. Ex, to set prefix ­pstnrule 1 123 456which means the first set of PSTN side rule is: IF user press 123888 after dialing in WellGate FXO GateWay from PSTN side ,the real number dialed out will become 456888. -iprule to do digit replacement of incoming call from IP side. Ex, to set 50