User manual WELLTECH FXSO GATEWAY H.323 3702A - VERSION 2.1A

FXSO GATEWAY User Manual (3701A/02A) Notice © Copyright 2002 Welltech Computer Co., Ltd. All intellectual property rights in this publication are owned by Welltech Computer Co., Ltd. and are protected by Republic of China copyright laws, other applicable copyright laws and international treaty provisions. Welltech Computer Co., Ltd. retains all rights not expressly granted. No part of this publication may be reproduced in any form whatsoever or used to make any derivative work without prior written approval by Welltech Computer Co., Ltd. No representation of warranties for fitness for any purpose other than what is specifically mentioned in this guide is made either by Welltech Computer Co., Ltd. or its agents. Welltech Computer Co., Ltd. reserves the right to revise this publication and make changes without obligation to notify any person of such revisions or changes. Welltech Computer Co., Ltd. may make improvements or changes in the product(s) and/or the program(s) described in this documentation at any time. If there is any software on removable media described in this publication, it is furnished under a license agreement included with the product as a separate document. If you are unable to locate a copy, please contact Welltech Computer Co., Ltd. and a copy will be provided to you. Unless otherwise indicated, Welltech Computer Co., Ltd. registered trademarks are registered in the Republic of China and other territories. For further information, contact Welltech or your local distributor or reseller. Welltech Computer Co., Ltd. 13F-4, No.150, Jian-Yi Road, Chung-Ho City, Taipei, Taiwan 235, R.O.C. Tel: +886-2-82265699 Fax: +886-2-82265799 E-mail: sales@mail.welltech.com.tw http://www.welltech.com.tw FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 STEPS IN CONFIGURATION ..................................................................................3 1. START UP ................................................................................................................4 1.1 INTRODUCTION......................................................................................................4 1.2 FEATURES AND SPECIFICATION ..............................................................................5 1.3 ACCESSORIES AND EQUIPMENT..............................................................................7 1.4 APPEARANCE.........................................................................................................8 2. HOW TO SETUP AND CONNECT BASICALLY............................................. 11 2.1 SYSTEM REQUIREMENT....................................................................................... 11 2.2 IP ENVIRONMENT SETTING .................................................................................12 2.2.1 For Windows 2000/NT ................................................................................12 2.3 NETWORK CONFIGURATIONS IN YOUR GATEWAY..................................................14 2.3.1 Static ip address ..........................................................................................16 2.3.2 DHCP mode ................................................................................................18 2.3.3 PPPoE mode ...............................................................................................19 2.4 MAKING A VOIP CALL ........................................................................................20 2.4.1 Configure the gateway into the Peer-to-Peer mode....................................20 2.4.2 Configure the gateway into the GK routed mode........................................24 2.4.2.1 The type in GK routed mode ....................................................................25 3. ADVANCED ...........................................................................................................28 3.1 IP SHARING .........................................................................................................28 3.2 LINE ....................................................................................................................33 3.3 GATEWAY PREFIX ................................................................................................35 3.4 FXO TYPE...........................................................................................................36 3.4 T.38.....................................................................................................................37 3.5 PREFIX ................................................................................................................38 3.6 ROUTING TABLE..................................................................................................41 3.6.1 Change the default routing .........................................................................42 3.6.2 Add a new Routing Table ............................................................................44 3.7 FXO PASSWORD..................................................................................................47 3.8 DDNS CONFIGURATION......................................................................................48 3.9 UPGRADE THE FIRMWARE ...................................................................................49 3.10 VERSION AND INFORMATION .............................................................................52 4. COMMAND LIST .................................................................................................53 4.1 HYPER TERMINAL SETTING.................................................................................53 Copyright (c) 2002 Welltech Computer Co. Ltd. 1 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 4.2 COMMAND LIST ..................................................................................................56 4.2.1 [help]...........................................................................................................56 4.2.2 [quit] ...........................................................................................................57 4.2.3 [debug]........................................................................................................57 4.2.4 [reboot] .......................................................................................................57 4.2.5 [flash]..........................................................................................................58 4.2.6 [commit]......................................................................................................58 4.2.7 [ifaddr]........................................................................................................59 4.2.8 [time]...........................................................................................................61 4.2.9 [ping] ..........................................................................................................61 4.2.10 [pppoe]......................................................................................................62 4.2.11 [sysconf] ....................................................................................................62 4.2.12 [h323] .......................................................................................................65 4.2.13 [line] .........................................................................................................69 4.2.14 [route] .......................................................................................................72 4.2.15 [prefix] ......................................................................................................74 4.2.16 [pbook]......................................................................................................75 4.2.17 [voice] .......................................................................................................77 4.2.18 [support] ...................................................................................................80 4.2.19 [phone]......................................................................................................82 4.2.20 [tone].........................................................................................................84 4.2.21 [fxopwd]....................................................................................................85 4.2.22 [record] .....................................................................................................86 4.2.23 [tos]...........................................................................................................94 4.2.24 [ddns]........................................................................................................95 4.2.25 [pt] ............................................................................................................96 4.2.26 [rom] .........................................................................................................97 4.2.27 [passwd]....................................................................................................98 Copyright (c) 2002 Welltech Computer Co. Ltd. 2 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 Steps in configuration STEP 1 Start Up To check out the peripheral equipments and understand the feature of this gateway. Please read this step very carefully before starting the configuring. Connecting the gateway and computer to start configuring by WEB GUI. STEP 2 How to Setup and Connect basically Setting the ip address for this gateway to make sure that it could connect with the internet. Setting the configurations of dialing, including the Peer-To-Peer, GK mode and how to set these tables to make calls by this gateway easily. The other configurations of make call will be discussed in this step. STEP 3 Advanced Advanced configurations and special functions of this gateway. Using the WEB GUI to show how to set this table and explain the meaning of these tables. STEP 4 Command List To explain the meaning of the command in the command line interface and example the usage of the command. To get more usages or configuration in this step and study about the command line configuration. Copyright (c) 2002 Welltech Computer Co. Ltd. 3 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 1. Start Up 1.1 Introduction WellGate 3701A/3702A is a one-port/two-port FXS+FXO gateway. It supports an innovative intelligent call rouging function that transparently routes calls to destination either through PSTN or Internet. WellGate 3701A/3702A provides voice over IP and FAX over IP services for ITSP/ISP Internet Telephony Services Provider and Office/SOHO IP-PBX application. Application Architecture PBX Extension port FXO IP Network FXS FXS FXS FXS FXO Trunk side PBX Extension FXO ports can connect with PSTN Line or Extension Line of PBX FXS ports can connect with Phone Set or Trunk Line of PBX Copyright (c) 2002 Welltech Computer Co. Ltd. 4 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 1.2 Features and specification Features ITU-T H.323 v2/v3/v4 compliance Automatically Dial Path Selection (IP or PSTN) PSTN Line switch to telephone set when power is failure PPPoE support Behind NAT router or IP sharing device DNS server inquiry Automatically Gatekeeper Discovery Provide Peer-to-Peer Mode (Non Gatekeeper needed) selection E.164 Dial Plan TFTP/FTP software upgrade Remote configuration/ reset LED indication for system status MS-NetMeeting v3.0 compatible Support Fix IP and DHCP Parameters of VoIP packet Audio feature Codec -- G.711 a/law, G.723.1 (6.3kbps), G.729, G.729A G.168/165-compliant adaptive echo cancellation Dynamic Jitter Buffer Completed voice band signaling support Provide In-band or Out-band DTMF generation/detection Provide call progress tone Management Feature - TELNET/Console port and Web Browser configuration Certification - UL, CE, FCC FXS Features Copyright (c) 2002 Welltech Computer Co. Ltd. 5 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 - 2-wire loop start Programmable On-Hook voltage, Ring voltage/Cadence/Frequency, Loop current Line polarity reversal generation FXO Features - 2-wire loop start - Support auto-attendant (Tone or voice greeting) - PSTN polarity reversal detection - Provide 2nd dial tone to PSTN - Disconnect tone detection - Asking ping function with the inside or outside calls Environmental Operation temp:0°C to 40°C Humidity: 10% to 90% (Non-condensing) Copyright (c) 2002 Welltech Computer Co. Ltd. 6 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 1.3 Accessories and equipment The voice gateway in 2/4 FXS ports models and two RJ-45 connector (WAN and LAN). The AC adapter. The CD of user manual. The connection cable in RS-232 interface. Copyright (c) 2002 Welltech Computer Co. Ltd. 7 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 1.4 Appearance Front panel: The LED lights provide related system messages of the gateway. WellGate 3701A WellGate 3702A Power: Light on means Gateway is power on, and vice versa. TEL: Light on means the line is in use (off-hook), and vice versa. LINE: Light on means the line is in use (off-hook), and vice versa. Status: 1. LED light on means Gateway has successfully registered to Gatekeeper when it is in Gatekeeper Mode. 2. LED flash means Gateway is not registered to Gatekeeper when it is in Gatekeeper Mode. 3. Or when Gateway is in downloading mode, LED should be flash as well. 4. LED light off means Gateway is in Peer-to-Peer Mode. Ready: 1. Light on and slow flash means Gateway is in normal mode. 2. Light on and fast flash means Gateway is in downloading mode. WAN: Connected to Public Ethernet 1. Line- LED light on means Gateway is physically connected to the Ethernet correctly. 2. ACT- LED light on and flash when Ethernet data is being transmitted / received. LAN: Switch to another device, such as PC 1. Line- LED light on means Gateway is physically connected to the Ethernet Copyright (c) 2002 Welltech Computer Co. Ltd. 8 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 correctly. 2. ACT- LED light on and flash when Ethernet data is being transmitted received. Back panel: WellGate 3701A WellGate 3702A 1. Ethernet Port LAN/WAN: 10/100 Base-T; RJ-45 socket, complied with ETHERNET 10/100base-T. The pin-out is as following: PIN 1, 2: Transmit PIN 3, 6: Receive 2. COM: RS232 console port (DB-9pin male connector) Note: use straightforward cable to connect to your computer. Copyright (c) 2002 Welltech Computer Co. Ltd. 9 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 PINOUTS Pin Name Dir 2 3 5 RXD TXD GND Description Receive Data Transmit Data System Ground 3. TEL: RJ-11 connector, FXS interface is for connecting the analog phone sets or trunk line of PABX. 4. LINE: RJ-11 connector, FXO interface is for connecting the extension line of PABX or PSTN Line. 5. 12V DC: Input AC 100V~120V;output DC12V. Copyright (c) 2002 Welltech Computer Co. Ltd. 10 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 2. How to Setup and Connect basically 2.1 System Requirement 1. One PC (a) Pentium 100 or above, 64 RAM, Windows 98 or above. (b) Ethernet card or COM port 2. One standard straightforward RS-232 cable (female connector to Gateway side). 3. Analog telephone sets. 4. PBX extension Lines or PSTN Lines. 5. Software tools (a) Hyper Terminal, TELNET, Web Browser. (b) Gatekeeper (optional). Copyright (c) 2002 Welltech Computer Co. Ltd. 11 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 2.2 IP Environment Setting User must prepare a valid IP address, complied with IP Network, for Gateway's proper operation. For testing the validation of chosen IP address, using the same IP configuration in other PC or Notebook, and then try to connect to Public Internet (go to well-known website, receive Internet mail, or ping a specific public IP address). If it works, use the same IP address and network configuration for Gateway. Please follow up the step for the configuration of your computer or notebook. 2.2.1 For Windows 2000/NT Please make sure that the network interface of your computer is working fine and the cross over line (RJ-45) is connecting with the computer correctly or you could use a hub to connect with your computer and this gateway. Turn on your computer and configure the network parameter as follow: 1 Go to the start menu and enter the setting area. Click control panel. 2 Enter the network configuration. Copyright (c) 2002 Welltech Computer Co. Ltd. 12 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 Figure 2.1: Network Configuration 3 Select the Property of the LAN card. 4 Setup the ip address, subnet mask and default gateway as below: Figure 2.2: Configure the network 5 Click OK after you finished the network setup. Copyright (c) 2002 Welltech Computer Co. Ltd. 13 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 The default ip address, netmask and default gateway address of the gateway is 10.1.1.3, 255.255.0.0, 10.1.1.254. 2.3 Network configurations in your gateway 1 Key in the ip address of the gateway (http://10.1.1.3) with the browser Copyright (c) 2002 Welltech Computer Co. Ltd. 14 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 2 After key in the ip address, you have to enter the user name and password to enter the WEB configuration. (Username: root ; No password) Figure 2.3: Login the username and password 3 You will enter the main page of the configuration after key in the login name and password correctly: Copyright (c) 2002 Welltech Computer Co. Ltd. 15 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 Figure 2.4: The main WEB configuration 4 Press the Network Interface to configure the networking of your gateway: Figure 2.5: The Network Interface 2.3.1 Static ip address 1 Please get the correct ip address, netmask and default gateway address from your ISP first. Press the OK button if you finished. Copyright (c) 2002 Welltech Computer Co. Ltd. 16 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 Figure 2.5: Configure the static ip address 2 Press the commit if you finish the configuration. Figure 2.6: Commit the data 3 Press the reboot if you want the configuration executed. Copyright (c) 2002 Welltech Computer Co. Ltd. 17 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 Figure 2.7: Reboot the system 2.3.2 DHCP mode 1 Enable the DHCP if you are using the cable modem or DHCP server. Figure 2.8: Enable the DHCP function Copyright (c) 2002 Welltech Computer Co. Ltd. 18 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 2 Please commit the data and reboot the machine after you enable the DHCP function. 2.3.3 PPPoE mode 1 Press the PPPoE Configuration and put the info of the PPPoE account and password in the configuration table. Figure 2.9: Configure the PPPoE function 2 Please commit the data and reboot the machine after you finished the configuration of PPPoE. Copyright (c) 2002 Welltech Computer Co. Ltd. 19 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 2.4 Making a VoIP Call There are two modes that you could configure the gateway for making VoIP calls. One is the Peer-to-Peer mode, another is GK routed mode. The configurations and functions are different. Please make sure about the mode you want and follow up the step to configure your gateway. 2.4.1 Configure the gateway into the Peer-to-Peer mode 1 Enter the H323 Configuration table and change the mode to Peer-to-Peer. Figure 2.10: Configure the Peer-to-Peer mode 2 Press the OK button which is on the buttom of this page to save the configuration. Copyright (c) 2002 Welltech Computer Co. Ltd. 20 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 Figure 2.11: Press OK to save the data 3 Enter the Phone Book configuration table and configure the name, ip address and phone number of the destination. Figure 2.12: Phone Book Copyright (c) 2002 Welltech Computer Co. Ltd. 21 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 Example Figure 2.13: The example of Phone Book configuration The name of the destination: test The E164 number (phone number) of the destination: 123 The ip address of the destination: 10.1.1.100 The call signal port of the destination: 1720 (The port will be 1720 if you don' t define it) Drop prefix: Enable ­ The e164 number you define will be deleted Disable ­ The e164 number you define will be kept Insert prefix: To add a number you define in this table Press the "Add Data" button when you finished, and the new table will display on the first index if you press the Phone Book configuration button. Copyright (c) 2002 Welltech Computer Co. Ltd. 22 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 4 Please Commit it and Reboot the system if the configuration is finished. Figure 2.14: To show the Phone Book record Phone Book is only for the Peer-to-Peer mode. Fifty index support. The application in the drop and insert function Input (E164) 100 200 300 400 Drop Disable Disable Enable Enable 23 Insert X 0 X 500 Output 100 0200 X 500 Copyright (c) 2002 Welltech Computer Co. Ltd. FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 X ­ Do not enter any numbers 2.4.2 Configure the gateway into the GK routed mode 1 Enter the H323 Configuration table and change the mode from Peer-to-Peer to GK routed. To change the GK information from your service provider (Ex: The Gatekeeper IP, Registered Prefix and Registered Alias). Figure 2.15: Configure the GK info 2 Press the OK button which is on the buttom of this page to save the configuration. Copyright (c) 2002 Welltech Computer Co. Ltd. 24 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 Figure 2.16: Press OK to save the data 3 Press the Commit Data and Reboot System buttons when you finished the configuration. 2.4.2.1 The type in GK routed mode There are two types in the GK routed mode you could choose. One is Gateway type and another is Terminal type. There are some different functions, applications and configurations between the Gateway type and Terminal type. Please get more info from the table as below: Gateway Type Prefix number is necessary The E164 number of each port should be follow the prefix number Support the one-stage dialing Terminal Type Prefix number is not necessary The E164 number of each port could be different Do not support the one-stage dialing The default type of the all series Welltech gateway are Gateway type. But the LanPhone is the terminal type. You could change the type for your gateway but the LanPhone couldn't. Please pick up the type you want to use with your gateway and pay more attentions about the rules as above. There are two example for the Gateway type and Terminal type as below: Copyright (c) 2002 Welltech Computer Co. Ltd. 25 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 Example ­ Gateway type Figure 2.17: Gateway Type configuration The prefix number is necessary if you configure it to be a gateway. The number of ports must be followed the prefix number. Example ­ Terminal type Copyright (c) 2002 Welltech Computer Co. Ltd. 26 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 Figure 2.18: Terminal Type configuration The prefix number is only for the gateway type and the number of ports could be configured in the different numbers. Copyright (c) 2002 Welltech Computer Co. Ltd. 27 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 3. Advanced There are too many advanced commands for the advanced users. The following chapters are based on the application layer. Please get the info what you need. If you need the command, please watching the chapter of Command Line Interface. 3.1 IP Sharing The function is only for the user who is using the IP Sharing device. It is said Gateway is connected to the IP Sharing device. The IP Sharing Device must support the DMZ or Virtual server functions An example such as ADSL network is in the following. ATU-R ADSL Modem WAN Copyright (c) 2002 Welltech Computer Co. Ltd. 28 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 IP Sharing device LAN LAN Gateway PC The WAN IP Address obtained from ADSL has two kinds of methods. One is fixed IP Address, while user applies for one or more fixed IP Addresses. Another is dynamic IP Address while user applies for dial-up connection way. The LAN IP Address of User's PC can be set as DHCP client in order to gain a valid one. Another IP Address for Gateway must be set as an fixed one in order for that IP Sharing device pass forwarding the relevant information from WAN to LAN. Besides, a valid IP Address meets the IP Sharing device (LAN site) is the element. Please configure your gateway just like below: 1 Enter the IP address, Netmask and the default gateway in the network table. Please follow up your IP Sharing device. Copyright (c) 2002 Welltech Computer Co. Ltd. 29 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 Figure 3.1: Network configuration 2 Enable the ip sharing function and put the static ip address in the server address table. Copyright (c) 2002 Welltech Computer Co. Ltd. 30 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 Figure 3.2: Enable the ip sharing function 1. Fixed IP ­ Please put the ip address of the ip sharing device in the IP Sharing Server Address table. 2. Dynamic IP ­ Just leave it if the IP sharing device is using PPPoE or DHCP protocol to connect with the internet. 3 The IP change function is only for the special usage Figure 3.3: IP Change IP Change Function: The ip address of the IP Sharing Server Address will use what you configured in that table if you disable the IP Change function. It supports the static ip address. If user is using the dynamic ip address, this function has to be enabled. 31 Copyright (c) 2002 Welltech Computer Co. Ltd. FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 If the wan port of the ip sharing device is using the dynamic ip address, the gateway couldn't get the ip address if the GK isn't from ours, too. 4 Please Commit it and Reboot the system if the configuration is finished. This chapter is focus on the DMZ function of the IP Sharing Device, Please get another application from our web site. Copyright (c) 2002 Welltech Computer Co. Ltd. 32 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 3.2 Line The Line configuration will show the status of the registrations and the ports. It includes the hunt group, hotline, and no answer forward configuration. Press the Line configuration button to enter configuration table (see figure 3.14) Figure 3.4: Line Configuration Type ­ Show the type of this port. There are only two types of this gateway. One is FXS type another is FXO type. It couldn't be changed. Hunting Group ­ Define the group number of this port. When the port is busy, the call could be transferred to another port in the same group. Hotline ­ Enable or Disable the hotline mode. The hotline mode will be enabled if you enter the hotline number. The default setting is disabled. No Answer Forward ­ When the port didn't answer the call, this call will be forwarded to the number you configured. This is only for the E164 number or the phone number you want to transfer. This function should be used with the forwardtime command (in the System configuration table). The range of the forward time is 5 to 65535. If the function is enable, the No Answer forward number is 123, and the forward time is 5 seconds. The call will be forwarded to the destination with 123 numbers when the origin port didn't answer the call. Copyright (c) 2002 Welltech Computer Co. Ltd. 33 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 Registration ­ To show the gateway registered on the GK or not. Status ­ To show the port is busy or ready. Copyright (c) 2002 Welltech Computer Co. Ltd. 34 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 3.3 Gateway Prefix The prefix number is necessary if the type of gateway is gateway type. The type of gateway is for the GK mode only. The Gateway Prefix function is only support the gateway which is the destination. Please enter the WEB configuration of this function if you want to configure it (see figure 3.5) Figure 3.5: Gateway Prefix The gateway could keep or drop the prefix number if the call is coming from the ip side and bring the prefix number of this gateway. The usage of this command is about the one-stage-dialing function. Of course it must work with the Routing table. Please get the info about the Routing table configuration in the chapter 3. Source 10012345 10012345 Gateway Prefix Keep Drop Receive 10012345 10012345 Transfer 10012345 12345 If the incoming call (From IP side) with the number is 10012345, and the prefix number of the destination gateway is 100. The gateway will receive 10012345. But the number it transfer will be 10012345 (Gateway Prefix Keep). The Copyright (c) 2002 Welltech Computer Co. Ltd. 35 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 transfer number will be 12345 if the Gateway Prefix function is enabled. 3.4 FXO Type The function coerces the calls to be two-stage-dialing. It working even the Routing Table has been configured. Enter the System Configuration to configure this function (see figure 3.6) Figure 3.6: FXO Type Normal ­ Following the origin usage Force 2nddial ­ Any calls to FXO port will be the two-stage-dialing Copyright (c) 2002 Welltech Computer Co. Ltd. 36 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 3.4 T.38 The T.38 is a "Real Time Group 3 Fax Communication over IP network" format. That's meaning it's a protocol for Fax over IP. You have to enable this function if you need the Fax issue. Press the Support button to enter the configuration table (see figure 3.7) Figure 3.7: T.38 configuration T.38 ­ Enable will Support Fax function, disable won't. T.38 Fax ECM ­ Error Correction during fax high speed Mode support. T.38 Fax ASN.1 Support ­ The transmission of voice data over packet switch networks support. Abstract Syntax Notation 1. Copyright (c) 2002 Welltech Computer Co. Ltd. 37 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 3.5 Prefix The Prefix function is using the drop and insert function (see figure 3.8). Figure 3.8: Prefix Configuration There is a rule between Prefix and Routing command, the Prefix command have priority over the Routing command. If there is a incoming call from any sides, the Routing will check this calling number after the Prefix checked (see figure 3.) YES Check the Prefix Table first Follow the Routing you configure NO Figure 3.9: The Priority Follow the Default Routing There is an example about the configuration, please follow up these steps. Copyright (c) 2002 Welltech Computer Co. Ltd. 38 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 1 Press the Prefix Configuration button to enter the configuration table (see figure 3.8) 2 Enter the index number. Put the prefix numbers you will dial in the prefix table, enable (disable) the drop function and enter the numbers you want to insert (see figure 3.10) Figure 3.10: Configure the Prefix Table The usage is as same as the drop, insert function of the Phone Book. Input (Prefix) 100 200 300 400 Drop Disable Disable Enable Enable 39 Insert X 0 X 500 Output 100 0200 X 500 Copyright (c) 2002 Welltech Computer Co. Ltd. FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 3 Press the Prefix Configuration button to reload the configuration table (see figure 3.11) Figure 3.11: Show the added table 4 Please Commit it and Reboot the system if the configuration is finished. Copyright (c) 2002 Welltech Computer Co. Ltd. 40 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 3.6 Routing Table Routing Table is a rule to define the destination of the calls you make. You could define the rules by the number you dial or by the ports. The Routing Table button will show you the configuration table (see figure 3.12). In fact, there are three directions of the incoming calls (from IP, FXS and FXO side). The explanation of the default routing is as below: The location with The location with the incoming calls the destination IP (Default) Fxs The explanation The destination will be the FXS port when the calls from the IP side without any define rules. The destination will be the IP side when the calls from the FXS port without any define rules. The destination will be the IP side when the calls from the FXO port without any define rules. Fxs (Default) IP Fxo (Default) IP Copyright (c) 2002 Welltech Computer Co. Ltd. 41 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 Figure 3.12: Routing Table Configuration 3.6.1 Change the default routing Please follow up the steps if you want to change the default routing: 1 Pick up the side for the incoming calls and define the destination of this side. Press the Change Default to save the data. Copyright (c) 2002 Welltech Computer Co. Ltd. 42 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 Figure 3.13: Change The Default Setting 2 The default setting is changed after you press the Change Default button. Please press the Routing Table button again to show the new setting. Copyright (c) 2002 Welltech Computer Co. Ltd. 43 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 Figure 3.14: The Default Setting Changed 3 Please Commit it and Reboot the system if the configuration is finished. 3.6.2 Add a new Routing Table 1 The default setting is changed after you press the Change Default button. Please press the Routing Table button again to show the new setting. Copyright (c) 2002 Welltech Computer Co. Ltd. 44 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 Figure 3.15: Edit and Add a new routing table Index ­ Define the number of this data. Prefix ­ Define the number you dial. You could just define the first digit of the numbers Destination ­ Define the destination of this rule. There are three directions of the destination. E164 ­ Define a right E164 number of the destination you want. For example: There are two FXO ports of the gateway (3702A) and I want the first FXO port (1002 is the default E164 number) to be the destination. So the E164 number I have to define is 1002. Min Digits ­ The minima digits you dial. Max Digits ­ The maxima digits you dial. The min and max digits are the range for the number you dial. For example: The min digits is 1 and max digits is 10. The call will follow this routing if the number I dial is between 1 and 10 digits. If I dial over 10 digits, this call will follow the default routing. Hunt ­ Define the hunt group function. 45 Copyright (c) 2002 Welltech Computer Co. Ltd. FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 None ­ Disable this function Group ­ The call will search other ports to be the destination with the same group if the origin destination is busy. All ­ The call will search other ports to be the destination with the same type if the origin destination is busy. 2 Press Add Data button to save the configuration and press the Routing Table button again to reload the configuration. Figure 3.16: New Special Routing The explanation of figure 3.16 is as below: When the user dial 0 with the first digit of the numbers (from FXS side), or from FXO and IP side. And the numbers you dial is between 1 and 10 digits. If this call matches the rule, it will be transferred to the FXO port whose E164 number is 1002. 3 Please Commit it and Reboot the system if the configuration is finished. Copyright (c) 2002 Welltech Computer Co. Ltd. 46 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 3.7 FXO Password You will get the IVR if you make calls from PSTN side or from IP side. The IVR will ask you the password you set, and you could make other calls to IP side or PSTN side if the password you type is correct. Please press the FXO Password button to configure the password (see figure 3.17) Figure 3.17: FXO Password Index ­ The number of this table. Password ­ The password you set. Direction ­ Playing the IVR to PSTN, IP or both side. (Out ­ To IP side ; In ­ To PSTN side) Copyright (c) 2002 Welltech Computer Co. Ltd. 47 FXSO H.323 Gateway User Manual Document Ver.: 2.1a Release Sep., 2003 3.8 DDNS Configuration This version of firmware supports DDNS function. Before using this function, please have a DDNS account and some info from your DDNS server. Press the DDNS Configuration button to configure it. (see figure 3.18) Figure 3.18: DDNS Configuration Status ­ To enable or disable this function. Server ­ Enter the server address of your DDNS server. Host Name ­ Your DDNS address. ID ­ Your account. Password ­ Your password. Please get this info from your DDNS server. IP Check Server ­ Will check the endpoints ip address. Check Every ­ The endpoint will check the server after a period. Copyright (c) 2002 Welltech Computer Co. Ltd. 48