K7V88 User Manual Version 1.0 Published March 2004 Copyright©2004 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. With respect to the contents of this manual, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the manual or product. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ASRock Website: http://www.asrock.com 2 Contents 1. Introduction .................................................. 5 1.1 1.2 1.3 1.4 Package Contents .......................................................... Specifications ................................................................ Motherboard Layout ...................................................... ASRock I/O PlusTM ................................................................................................. 5 6 8 9 10 11 11 12 14 15 17 20 20 21 22 22 23 23 24 24 25 27 28 30 30 31 32 33 33 34 34 35 36 2. Installation .................................................... 10 Pre-installation Precautions ................................................... 2.1 CPU Installation .............................................................. 2.2 Installation of CPU Fan and Heatsink ............................ 2.3 Installation of Memory Modules (DIMM) ......................... 2.4 Expansion Slots (PCI and AGP Slots) ........................... 2.5 Jumpers Setup .............................................................. 2.6 Onboard Headers and Connectors .............................. 2.7 Serial ATA (SATA) Hard Disks Installation ..................... 2.8 Hot Plug and Hot Swap Functions for SATA HDDs ....... 2.9 Making An SATA Driver Diskette .................................... 3.1 Introduction .................................................................... 3.1.1 BIOS Menu Bar .................................................... 3.1.2 Navigation Keys ................................................... 3.2 Main Screen ................................................................... 3.3 Advanced Screen ......................................................... 3.3.1 CPU Configuration ................................................ 3.3.2 Chipset Configuration .......................................... 3.3.3 ACPI Configuration ............................................... 3.3.4 IDE Configuration ................................................. 3.3.5 PCIPnP Configuration ........................................... 3.3.6 Floppy Configuration ........................................... 3.3.7 Super IO Configuration ........................................ 3.3.8 USB Configuration ............................................... 3.4 Hardware Health Event Monitoring Screen .................. 3.5 Boot Screen ................................................................... 3.5.1 Boot Settings Configuration .................................. 3.5.2 Boot Device Priority ............................................... 3.6 Security Screen ............................................................ 3.7 Exit Screen .................................................................... 3. BIOS SETUP UTILITY ......................................... 22 3 4. Software Support .......................................... 37 4.1 Install Operating System ............................................... 4.2 Support CD Information ................................................. 4.2.1 Running Support CD ............................................ 4.2.2 Drivers Menu ........................................................ 4.2.3 Utilities Menu ........................................................ 4.2.4 ASRock "PC-DIY Live Demo" Program ................. 4.2.5 Contact Information .............................................. 37 37 37 37 37 37 37 4 1. Introduction Thank you for purchasing ASRock K7V88 motherboard, a reliable motherboard produced under ASRock's consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock's commitment to quality and endurance. In this manual, chapter 1 and 2 contain introduction of the motherboard and step-bystep guide to the hardware installation. Chapter 3 and 4 contain the configuration guide to BIOS setup and information of the Support CD. Because the motherboard specifications and the BIOS software might be updated, the content of this manual will be subject to change without notice. In case any modifications of this manual occur, the updated version will be available on ASRock website without further notice. You may find the latest memory and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com 1.1 Package Contents ASRock K7V88 Motherboard (ATX Form Factor: 12.0-in x 8.0-in, 30.5 cm x 20.3 cm) ASRock K7V88 Quick Installation Guide ASRock K7V88 Support CD One 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable One Ribbon Cable for a 3.5-in Floppy Drive One Serial ATA (SATA) Data Cable One Serial ATA (SATA) HDD Power Cable(Optional) One ASRock I/O PlusTM Shield 5 1.2 Specifications Platform: CPU: Chipsets: ATX Form Factor: 12.0-in x 8.0-in, 30.5 cm x 20.3 cm Supports Socket A (462 pins) for AMD AthlonTM / AthlonTM XP / DuronTM processor North Bridge: VIA KT880, FSB @ 400 MHz South Bridge: VIA VT8237, supports USB 2.0, ATA 133, SATA 1.5Gb/s Memory: 4 DDR DIMM Slots: DDR1, DDR2, DDR3, and DDR4 Support PC3200 (DDR400) / PC2700 (DDR333) / PC2100 (DDR266), Max. 4GB Dual Channel Memory Technology support (see CAUTION 1) IDE: IDE1: ATA 133 / Ultra DMA Mode 6 IDE2: ATA 133 / Ultra DMA Mode 6 Support up to 4 IDE devices Serial ATA: 2 SATA connectors Support 1.5Gb/s data transfer rate Floppy Port: Supports up to 2 floppy disk drives Audio: 5.1 channels AC'97 Audio LAN: Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN Hardware Monitor: CPU temperature sensing (ASRock U-COP) Chassis temperature sensing CPU overheat shutdown to protect CPU life (ASRock U-COP)(see CAUTION 2) CPU fan tachometer Chassis fan tachometer Voltage monitoring: +12V, +5V, +3V, Vcore PCI slots: 5 slots with PCI Specification 2.3 AGP slot: 1 AGP slot, supports 1.5V, 8X/4X AGP card (see CAUTION 3) USB 2.0: 8 USB 2.0 ports: include 6 ready-to-use USB 2.0 ports on the rear panel, plus one on-board header supporting 2 extra USB 2.0 ports (see CAUTION 4) ASRock I/O PlusTM: 1 PS/2 mouse port, 1 PS/2 keyboard port, 1 serial port: COM1, 1 parallel port: ECP/EPP support, 6 ready-to-use USB 2.0 ports, 1 RJ 45 port, Audio Jack: Line In / Line Out / Microphone 6 BIOS: OS: AMI BIOS Supports "Plug and Play" ACPI 1.1 compliance wake up events SMBIOS 2.3.1 support CPU frequency stepless control (only for advanced users' reference, see CAUTION 5) Microsoft® Windows® 98SE / ME / 2000 / XP compliant CAUTION! 1. This motherboard supports Dual Channel Memory Technology. Before you implement Dual Channel Memory Technology, make sure to read the installation guide of memory modules on page 12 for proper installation. While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again. To improve heat dissipation, remember to spray thermal grease between the CPU and the heatsink when you install the PC system. 3. 4. Do NOT use a 3.3V AGP card on the AGP slot of this motherboard! It may cause permanent damage! Power Management for USB 2.0 works fine under Microsoft® Windows® XP SP1 / 2000 SP4. It may not work properly under Microsoft® Windows® 98 / ME. Please refer to Microsoft® official document at http://www.microsoft.com/whdc/hwdev/bus/USB/USB2support.mspx 5. Although this motherboard offers stepless control, it is not recommended to perform over clocking. Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU. The CPU host frequency of this motherboard is determined by the jumper-setting. To perform over-clocking, you must set the FSB jumper according to your AMD CPU before you use the "Manual" option as the FSB setting in BIOS setup. Please check page 22 for details. 2. 7 1.3 Motherboard Layout 1 1 PS2 Mouse 2 34 20.3cm (8.0 in) PS2_USB_PWR1 CPU_FAN1 5 6 7 ATX12V1 PARALLEL PORT PS2 Keyboard J1 1 COM1 DDR1 (64/72 bit, 184-pin module) DDR2 (64/72 bit, 184-pin module) DDR3 (64/72 bit, 184-pin module) USB 2.0 Top: T: USB0 RJ-45 B: USB1 34 USB 2.0 1 T: USB4 B: USB5 USB45 CD1 ATXPWR1 33 Top: Line In Center: Line Out Bottom: Mic In K VIA T hi 88 ps 0 et 32 31 Audio CODEC C AUX1 AGP 8X SATA FSB_SEL0 Dual Channel 30.5cm (12.0 in) 8 9 10 11 12 13 14 15 16 17 18 19 20 USB 2.0 T: USB2 B: USB3 30 29 28 LAN PHY JR1 1 1.5V_AGP1 IDE2 JL1 AUDIO1 PCI 1 ` Super I/O PCI 2 IDE1 27 26 25 2MB BIOS K7V88 PCI 3 FSB400 USB2.0 5.1 CH SATA2 VIA VT8237 FLOPPY1 SATA1 1 GAME1 PCI 4 ATA133 DDR400 PCI 5 IR1 1 CMOS Battery CLRCMOS2 1 CHA_FAN1 PWR_LED11 USB67 SPEAKER1 1 1 HDLED RESET PLED PWRBTN PANEL 1 24 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PS2_USB_PWR1 Jumper CPU Fan Connector (CPU_FAN1) CPU Multiplier Jumper (J1) CPU Socket North Bridge Controller ATX 12V Connector (ATX12V1) 2 x 184-pin DDR DIMM Slots (Dual Channel A: DDR1, DDR3; Blue) 2 x 184-pin DDR DIMM Slots (Dual Channel B: DDR2, DDR4; Black) FSB Select Jumper (FSB_SEL0) FSB Select Jumper (FSB_SEL1) AGP Slot (1.5V_AGP1) Secondary IDE Connector (IDE2, Black) Primary IDE Connector (IDE1, Blue) South Bridge Controller Secondary Serial ATA Connector (SATA2) Primary Serial ATA Connector (SATA1) 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 23 22 21 Floppy Connector (FLOPPY1) Chassis Fan Connector (CHA_FAN1) Power LED Header (PWR_LED1) System Panel Header (PANEL1) Chassis Speaker Header (SPEAKER 1) USB 2.0 Header (USB67, Blue) Clear CMOS Jumper (CLRCMOS2) Infrared Module Header (IR1) Game Port Connector (GAME1) Flash Memory 5 x PCI Slots (PCI1- 5) Front Panel Audio Header (AUDIO1) JR1 Jumper JL1 Jumper ATX Power Connector (ATXPWR1) Internal Audio Connector: AUX1 (White) Internal Audio Connector: CD1 (Black) Shared USB 2.0 Header (USB45, Blue) 8 DDR4 (64/72 bit, 184-pin module) 1 1 FSB_SEL1 SOCKET 462 1.4 ASRock I/O Plus TM 1 2 3 4 5 11 10 9 8 7 6 1 2 3 4 5 6 Parallel Port RJ-45 Port Line In (Light Blue) Line Out (Lime) Microphone (Pink) 2 x Shared USB 2.0 Ports (USB4, USB5) 7 8 9 10 11 2 x USB 2.0 Ports (USB0, USB1) 2 x USB 2.0 Ports (USB2, USB3) Serial Port: COM1 PS/2 Keyboard Port (Purple) PS/2 Mouse Port (Green) 9 2. Installation K7V88 is an ATX form factor (12.0-in x 8.0-in, 30.5 cm x 20.3 cm) motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Pre-installation Precautions Take note of the following precautions before you install motherboard components or change any motherboard settings. 1. 2. Unplug the power cord from the wall socket before touching any component. To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components. Hold components by the edges and do not touch the ICs. Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component. Before you install or remove any component, ensure that the power is switc ...