magicolor 2430 DL Warranty Exchange Guide ® 1760667-001A Trademarks KONICA MINOLTA and the KONICA MINOLTA logo are trademarks or registered trademarks of KONICA MINOLTA HOLDINGS, INC. magicolor is a trademark or registered trademark of KONICA MINOLTA PRINTING SOLUTIONS U.S.A., INC. All other trademarks are the property of their respective owners. Copyright Notice Copyright © 2004 KONICA MINOLTA PRINTING SOLUTIONS U.S.A., INC., One Magnum Pass, Mobile, AL 36618, USA. All Rights Reserved. This document may not be copied, in whole or part, nor transferred to any other media or language, without written permission of KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. Manual Notice KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. reserves the right to make changes to this manual and to the equipment described herein without notice. Considerable effort has been made to ensure that this manual is free of inaccuracies and omissions. However, KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. makes no warranty of any kind including, but not limited to, any implied warranties of merchantability and fitness for a particular purpose with regard to this manual. KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. assumes no responsibility for, or liability for, errors contained in this manual or for incidental, special, or consequential damages arising out of the furnishing of this manual, or the use of this manual in operating the equipment, or in connection with the performance of the equipment when so operated. Introduction Thank you for contacting a technical support representative to obtain information about returning your printer for warranty exchange. Follow these instructions very carefully. If you need additional assistance, refer to the General Information Guide (included with the original printer) or printer.konicaminolta.com for worldwide sources of service and support. Attention Failure to follow these instructions could result in voiding your warranty. Exchange Procedure Each of these steps is explained in detail in this guide. 1 2 3 4 5 Unpack the exchange printer. Prepare the original printer--turn it off, unplug the power cord, and remove the interface cables and dust cover. See page 2. See page 4. Move the consumables (the four toner cartridges, the See page 6. drum cartridge, and the transfer belt unit) from the original printer to the exchange printer. Finish setting up the exchange printer--plug it in, attach See page 12. the interface cables, turn it on, install the dust cover, and fill the tray with media. Repack the original printer, and call the shipper for pickup. See page 14. Introduction 1 Unpack the Exchange Printer Attention Use caution when unpacking the exchange printer, so the packaging can be used to repack the printer to be returned. 1 Unpack the exchange printer. WARNING! The printer weighs approximately 40 lbs/18 kg without consumables. Be sure to have help when lifting and moving it. Exchange 2 Remove the tape from the Exchange 2 outside of the exchange printer. Unpack the Exchange Printer 3 Open the input and exit trays on the exchange printer. Exchange 4 Remove the fuser separators from the exchange printer. Exchange See the instructions on the fuser separator tag for more details. Unpack the Exchange Printer 3 Prepare the Original Printer 1 Turn off the original printer, unplug the power cord, and remove the interface cable. A B Original C 4 Prepare the Original Printer 2 Remove the media and dust cover from the original printer. A B Original C 3 Close the top cover of the original printer. ! Original " Prepare the Original Printer 5 Move the Consumables Toner Cartridges 1 At the control panel of the original printer, access the ENGINE/ SERVICE/REMOVE ALL TONER menu and choose YES. Original The toner cartridge rack moves into removal position, and OPEN DOOR/REMOVE TONER C displays in the message window. OPEN DOOR REMOVE TONER C 2 Remove the cyan toner cartridge. A B C Original D E 6 Move the Consumables Original Exchange 3 Repeat steps 1 and 2 three more times to move the original printer's remaining toner cartridges into removal position and then remove them: black (K), yellow (Y), and then magenta (M). 4 At the control panel of the exchange printer, access the ENGINE/ SERVICE/REPLACE TONER menu and choose CYAN. The toner cartridge rack moves into position, and OPEN DOOR/ REPLACE TONER C displays in the message window. OPEN DOOR REPLACE TONER C Move the Consumables 7 5 Insert the cyan toner cartridge into the exchange printer. A B C Exchange D E F Exchange 8 6 Repeat steps 4 and 5 three more times to move the toner cartridge rack into position on the exchange printer, and insert the remaining toner cartridges: black (K), yellow (Y), and magenta (M). Move the Consumables Drum Cartridge 1 Open the top cover of the original printer, and then carefully pull out the drum cartridge. A Original B 2 Open the top cover of the exchange printer, and then carefully insert the drum cartridge. A Exchange B Move the Consumables 9 Transfer Belt Unit 1 With the top cover of the Original Original Original original printer still open, disconnect the transfer belt unit connector. 2 Remove two screws-- one on each side of the transfer belt unit. 3 Slide out the transfer belt unit out of the original printer, and then close the top cover. # Be careful not to $ scratch the transfer belt. 4 With the top cover of the Exchange 10 exchange printer still open, slide the transfer belt unit into place. Move the Consumables 5 Install two screws-- Exchange Exchange Exchange Original one on each side of the transfer belt unit. 6 Connect the transfer belt unit connector. 7 Close the top cover of the exchange printer. 8 Close the top cover of the original printer. Move the Consumables 11 Move the Power Cord, Interface Cables, and Dust Cover 1 Plug the power cord into the Exchange exchange printer and into an electrical socket. 2 Plug the interface cable into the exchange printer. Exchange 3 Turn on the exchange printer. Exchange 12 Move the Power Cord, Interface Cables, and Dust Cover 4 Install the dust cover (2 pieces), and fill the tray with paper. A B C Exchange D E F Move the Power Cord, Interface Cables, and Dust Cover 13 Repack the Original Printer 1 Replace the packing tape Original on the outside of the original printer. 2 Repack the original printer in the carton in which the exchange printer was shipped. Original 14 Original 3 Securely tape the top flaps of the shipping carton closed. Repack the Original Printer 4 In the Americas, clearly write the RMA (Return Merchandise Original Authorization) number you received from your customer support representative on the outside of the carton before calling the shipper for pickup. # If the RMA number is not prominently visible on the outside $ of the return carton, we will not accept receipt. Original 5 Ship the printer, using the shipper and shipping label provided with the exchange printer. Repack the Original Printer 15 ...