User manual HARMAN KARDON AVR 347 - annexe 1

AVR 347 AUDIO/VIDEO RECEIVER OWNER'S MANUAL SAFETY INFORMATION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN 1. Read Instructions. All the safety and operating instructions should be read before the product is operated. 2. Retain Instructions. The safety and operating instructions should be retained for future reference. 3. Heed Warnings. All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions. All operating and use instructions should be followed. 5. Cleaning. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. Attachments. Do not use attachments not recommended by the product manufacturer, as they may cause hazards. 7. Water and Moisture. Do not use this product near water ­ for example, near a bathtub, wash bowl, kitchen sink or laundry tub; in a wet basement; near a swimming pool; or the like. 8. Accessories. Do not place this product on an unstable cart, stand, tripod, bracket or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. 9. A Product and Cart Combination Should Be Moved With Care. Quick stops, excessive force and uneven surfaces may cause the product and cart combination to overturn. 10. Ventilation. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation, such as a bookcase or rack, unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 11. Power Sources. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your 2 home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12. Polarization. This product may be equipped with a polarized alternating-current-line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 13. Power-Cord Protection. Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 14. Nonuse Periods. The power cord of the product should be unplugged from the outlet when left unused for long periods of time. 15. Outdoor Antenna Grounding. If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A. 16. Lightning. For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 17. Power Lines. An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal. Figure A. Example of Antenna Grounding as per National Electrical Code ANSI/NFPA 70 18. Overloading. Do not overload wall outlets, extension cords, or integral convenience receptacles, as this can result in a risk of fire or electric shock. 19. Object and Liquid Entry. Never push objects of any kind into this product through openings, as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 20. Servicing. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 21. Damage Requiring Service. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. The power-supply cord or the plug has been damaged; or b. Objects have fallen onto, or liquid has been spilled into, the product; or c. The product has been exposed to rain or water; or d. The product does not operate normally when following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation; or e. The product has been dropped or damaged in any way; or f. The product exhibits a distinct change in performance; this indicates a need for service. 22. Replacement Parts. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. 23. Safety Check. Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 24. Wall or Ceiling Mounting. The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 25. Heat. The product should be situated away from heat sources such as radiators, heat registers, stoves or other products (including amplifiers) that produce heat. SAFETY INFORMATION Important Safety Information Verify Line Voltage Before Use Your AVR 347 has been designed for use with 120-volt AC current. Connection to a line voltage other than that for which it is intended can create a safety and fire hazard and may damage the unit. If you have any questions about the voltage requirements for your specific model, or about the line voltage in your area, contact your selling dealer before plugging the unit into a wall outlet. unit's feet may leave marks on certain wood or veneer materials. Use caution when placing the unit on soft woods or other materials that may be damaged by heat or heavy objects. Some surface finishes may be particularly sensitive to absorbing such marks, due to a variety of factors beyond Harman Kardon's control, including the nature of the finish, cleaning materials used, and normal heat and vibration caused by the use of the product, or other factors. We recommend that caution be exercised in choosing an installation location for the component and in normal maintenance practices, as your warranty will not cover this type of damage to furniture. Do Not Use Extension Cords To avoid safety hazards, use only the power cord attached to your unit. We do not recommend that extension cords be used with this product. As with all electrical devices, do not run power cords under rugs or carpets or place heavy objects on them. Damaged power cords should be replaced immediately by an authorized service center with a cord meeting factory specifications. Cleaning When the unit gets dirty, wipe it with a clean, soft, dry cloth. If necessary, and only after unplugging the AC power cord, wipe it with a soft cloth dampened with mild soapy water, then a fresh cloth with clean water. Wipe it dry immediately with a dry cloth. NEVER use benzene, aerosol cleaners, thinner, alcohol or any other volatile cleaning agent. Do not use abrasive cleaners, as they may damage the finish of metal parts. Avoid spraying insecticide near the unit. Handle the AC Power Cord Gently When disconnecting the power cord from an AC outlet, always pull the plug; never pull the cord. If you do not intend to use the unit for any considerable length of time, disconnect the plug from the AC outlet. Moving the Unit Before moving the unit, be certain to disconnect any interconnection cords with other components, and make certain that you disconnect the unit from the AC outlet. Do Not Open the Cabinet There are no user-serviceable components inside this product. Opening the cabinet may present a shock hazard, and any modification to the product will void your guarantee. If water or any metal object such as a paper clip, wire or staple accidentally falls inside the unit, disconnect it from the AC power source immediately, and consult an authorized service center. Important Information for the User This equipment has been tested and found to comply with the limits for a Class-B digital device, pursuant to Part 15 of the FCC Rules. The limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio-frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that harmful interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation. NOTE: Changes or modifications may cause this unit to fail to comply with Part 15 of the FCC Rules and may void the user's authority to operate the equipment. CATV or Antenna Grounding If an outside antenna or cable system is connected to this product, be certain that it is grounded so as to provide some protection against voltage surges and static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements of the grounding electrode. NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call the CATV (cable TV) system installer's attention to article 820-40 of the NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possible. Installation Location · To ensure proper operation and to avoid the potential for safety hazards, place the unit on a firm and level surface. When placing the unit on a shelf, be certain that the shelf and any mounting hardware can support the weight of the product. · Make certain that proper space is provided both above and below the unit for ventilation. If this product will be installed in a cabinet or other enclosed area, make certain that there is sufficient air movement within the cabinet. Under some circumstances, a fan may be required. · Do not place the unit directly on a carpeted surface. · Avoid installation in extremely hot or cold locations, or in an area that is exposed to direct sunlight or heating equipment. · Avoid moist or humid locations. · Do not obstruct the ventilation slots on the top of the unit, or place objects directly over them. · Due to the weight of the AVR 347 and the heat generated by the amplifiers, there is the remote possibility that the rubber padding on the bottom of the Unpacking The carton and shipping materials used to protect your new receiver during shipment were specially designed to cushion it from shock and vibration. We suggest that you save the carton and packing materials for use in shipping if you move, or should the unit ever need repair. To minimize the size of the carton in storage, you may wish to flatten it. This is done by carefully slitting the tape seams on the bottom and collapsing the carton. Other cardboard inserts may be stored in the same manner. Packing materials that cannot be collapsed should be saved along with the carton in a plastic bag. If you do not wish to save the packaging materials, please note that the carton and other sections of the shipping protection are recyclable. Please respect the environment and discard those materials at a local recycling center. It is important that you remove the protective plastic film from the front-panel lens. Leaving the film in place will affect the performance of your remote control. 3 STAPLE INVOICE HERE 4 TABLE OF CONTENTS 2 6 8 10 13 16 18 19 19 19 19 20 20 21 21 21 21 22 22 23 24 24 24 24 24 28 28 29 29 31 31 32 33 33 34 35 36 39 39 39 39 40 40 40 40 41 41 42 42 43 44 44 46 SAFETY INFORMATION INTRODUCTION FRONT-PANEL CONTROLS REAR-PANEL CONNECTIONS MAIN REMOTE CONTROL FUNCTIONS ZONE II REMOTE CONTROL FUNCTIONS INTRODUCTION TO HOME THEATER CONNECTIONS Speaker Connections Subwoofer Connecting Source Devices to the AVR Audio Connections Digital Audio Analog Audio Video Connections Digital Video Analog Video Antennas RS-232 Serial Port SPEAKER PLACEMENT INSTALLATION Step One ­ Connect the Speakers Step Two ­ Connect the Subwoofer Step Three ­ Connect the Antennas Step Four ­ Connect the Source Components Step Five ­ Connect Video Display Step Six ­ Plug in AC Power Step Seven ­ Insert Batteries in Remote Step Eight ­ Program Sources Into the Remote Step Nine ­ Remote IR Inputs and Output Step Ten ­ Install a Multiroom System Step Eleven ­ Turn On the AVR 347 INITIAL SETUP Using the On-Screen Menu System Configure the AVR 347 Using EzSet/EQ What EzSet/EQ Does Configure Sources OPERATION Turning On the AVR 347 Sleep Timer Volume Control Mute Function Tone Controls Headphones Source Selection Audio Input Selection Video Input Selection 6-/8-Channel Direct Inputs Using the Tuner XM Radio Operation Recording Using TheBridge Selecting a Surround Mode TM 47 ADVANCED FUNCTIONS 47 Audio Processing and Surround Sound 47 Analog Audio Signals 47 Digital Audio Signals 48 Surround Modes 49 Dolby Surround Settings 49 Default Modes 53 Manual Setup 53 Step One ­ Determine Speaker Size 53 Step Two ­ Measure Speaker Distances 53 Step Three ­ Manual Setup Menu 54 Speaker Size Menu 55 Speaker Crossover Menu 55 Delay Adjust Menu 56 Step Four ­ Setting Channel Output Levels Manually 57 Video Adjustments 58 Multiroom Operation 58 Installing a Multiroom System 59 Operating the Multiroom System 59 System Settings 60 Dim Function 60 Advanced Remote Control Functions 60 Punch-Through Programming 61 Macros 61 Resetting the Remote 61 Processor Reset 61 Memory 62 TROUBLESHOOTING GUIDE 63 TECHNICAL SPECIFICATIONS 63, 66 Trademark Acknowledgements 64 APPENDIX WARNING To prevent fire or shock hazard, do not expose this appliance to rain or moisture. For Canadian model This class B digital apparatus complies with Canadian ICES-003. For models having a power cord with a polarized plug: CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert. Modèle pour les Canadien Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Sur les modèles dont la fiche est polarisee: ATTENTION: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu'au fond. 5 INTRODUCTION Please register your AVR 347 on our Web site at www.harmankardon.com. Note: You'll need the product's serial number. At the same time, you can choose to be notified about our new products and/or special promotions. WWW.HARMANKARDON.COM Thank you for choosing Harman Kardon®! In the years since Harman Kardon invented the high-fidelity receiver, we have taken to heart the philosophy of bringing the joy of home entertainment to as many people as possible, adding performance and ease-of-use features that enhance the home entertainment experience. In the years since our first single-channel component was introduced, Harman Kardon has offered a number of receiver models, each an improvement upon its predecessors, leading to the AVR 347, a 7.1-channel digital audio/video receiver that offers a wealth of listening and viewing options, all in an elegant package. To obtain the maximum enjoyment from your new receiver, we urge you to read this manual and refer back to it as you become more familiar with its features and their operation. If you have any questions about this product, its installation or its operation, please contact your retailer or customer installer, or visit our Web site at www.harmankardon.com. AVR 347 7.1-Channel Audio/Video Receiver Audio Section · 55 Watts x 7, seven channels driven at full power at 8 ohms, 20Hz ­ 20kHz, <0.07% THD (surround modes), 385 watts total · 70 Watts x 2, two channels driven at full power at 8 ohms, 20Hz ­ 20kHz, <0.07% THD (surround off mode), 140 watts total · High-current capability, ultrawide-bandwidth amplifier design with low negative feedback · All-discrete amplifier circuitry · Dual independent power supplies, for front and surround channels · Quadruple-crossover bass management · 24-Bit, twin-core Cirrus Logic® CS 49510 DSP processor with 32-bit postprocessor · 192kHz/24-bit D/A conversion · Sampling upconversion to 96kHz Surround Modes · Dolby® Digital EX · Dolby Pro Logic® II and IIx (Movie, Music and Game) · Dolby Virtual Speaker Version 2 (Reference two- or three-speaker; Wide two-, three-, four- or five-speaker) · Dolby Headphone Version 2 · DTS® (5.1; DTS Stereo; DTS-ES® 6.1 Discrete and Matrix) · DTS 96/24TM (DTS Stereo) · DTS Neo:6® (Cinema 3-, 5- or 6-channel; Music 5- or 6-channel) · Logic 7® (Cinema, Music and Enhance ­ 5.1 and 7.1) · Hall 1 and Hall 2 (5- or 6-channel) · Theater (5- or 6-channel) · 5- or 7-Channel Stereo · Surround Off (DSP or Analog Bypass) 6 INTRODUCTION Audio Inputs · AM/FM/XM®* tuner · CD · Tape · 6-/8-Channel direct · Bridge /DMP for iPod** connectivity with audio/video playback The TM Ease of Use · EzSet/EQTM automated setup (microphone supplied) · Graphic on-screen display with HDMI, component, composite and S-video · Two-line dot-matrix front-panel display · Color-coded connections · Programmable 11-device main remote control · Source input renaming · A/V Sync Delay · RS-232 serial port for system upgrades · Switched accessory power outlet · Remote infrared (IR) input and output · Multiroom IR input · IEC detachable AC power cord for easy installation The AVR 347 is Simplay HD-verified for compatibility via the HDMI connection with other Simplay HD-verified products. Audio/Video Inputs (With S-Video) · Video 1 · Video 2 · Video 3 · Video 4 (on front panel) · DVD · Three assignable 100MHz component video inputs · Simplay HDTM-verified HDMITM 1 and 2 with audio/video processing, 1080p pass-through and repeater for increased cable lengths without signal degradation · DCDi® by Faroudja video processing Transcodes composite and S-video to component video Transcodes 480i video to HDMI format, with upscaling up to 720p Upgraded graphic text-based on-screen displays Supplied Accessories The following accessory items are supplied with the AVR 347. If any of these items are missing, please contact Harman Kardon customer service at www.harmankardon.com. · System and Zone II remote controls · EzSet/EQ microphone · AM loop antenna · FM wire antenna · Five AAA batteries · Two covers for front-panel jacks · AC Power cord Digital Audio Inputs · Coaxial: three rear-panel/one front-panel · Optical: three rear-panel/one front-panel Outputs · 7.1-Channel preamp outputs · Tape (analog audio) · Video 1 (analog audio and video) · Video monitor (composite, S-video and component) · Digital audio (one coaxial, one optical) · Simplay HD-verified HDMI · Multiroom audio · Multiroom speaker- and preamp (shared with surround back channels) · A-BUS® Ready · Headphone *XM antenna module and subscription to XM service required. Hardware and service sold separately. XM service is not available in Alaska or Hawaii. **Compatible with all iPod models equipped with a dock connector. Not compatible with iPod shuffle models. Images and videos stored on iPod photo and video models may be viewed. 7 FRONT-PANEL CONTROLS Main Power Switch: This mechanical switch turns the power supply on or off. It is usually left pressed in (On position), and cannot be turned on using the remote control. Surround Mode: Press this button to select a surround sound (e.g., multichannel) mode group. Choose from the Dolby modes, DTS modes, Logic 7 modes, DSP modes or Stereo modes. Standby/On Switch: This electrical switch turns the receiver on for playback, or leaves it in Standby mode for quick turn-on using this switch or the remote control. Power Indicator: This LED has three possible modes. When main power is turned off, the LED is dark and the receiver won't respond to any button presses. When main power is turned on, but before the Standby/On Switch is used, the LED turns amber to indicate that the receiver is in Standby mode and ready to be turned on. When the receiver is turned on, the LED turns blue. Surround Select: After you have selected the desired surround mode group, press this button to select a specific mode. Surround Mode Indicators: One or more of these icons may light up as you select different surround modes. The Message Display also indicates the surround mode. Analog Audio, Video and Digital Audio Inputs: Connect a source component that will only be used temporarily, such as a camera or game console, to these jacks. Use only one type of audio and one type of video connection. Speaker/Channel Input Indicators: The box icons indicate which speaker positions you have configured, and the size (frequency range) of each speaker. When a digital audio input is used, letters will light inside the boxes to indicate which channels are present in the incoming signal. Source Select: Press this button to select a source device, which is a component where a playback signal originates, e.g., DVD, CD, cable TV, satellite or HDTV tuner. Source Indicators: The name of the current source input lights up. The indicated input changes each time the Source Select button is pressed. Volume Knob: Turn this knob to raise or lower the volume, which will be shown in decibels (dB) in the Message Display. Navigation: These buttons are used together with the following five buttons to make selections. Tone Mode: Press this button to access the tone controls (bass and treble). Use the < / > Navigation Buttons to make your selections. Message Display: Various messages appear in this two-line display in response to commands and changes in the incoming signal. When the on-screen display menu system (OSD) is in use, the message OSD ON will appear to remind you to check the video display. Speaker: Press this button to configure speaker sizes; that is, the low-frequency-range capability of each speaker. Channel Level Adjust: Press this button to set the output level for each channel so that all speakers sound equally loud at the listening position. Digital Input Select: Press this button to select the specific digital audio input (or analog audio input) you used for the current source. Tuner Band: Press this button to select the tuner as the source, to switch between the AM and FM bands, or to select XM satellite radio. Tuning: Press either side of this button to tune a radio station or XM channel. Tuning Mode: This button toggles between manual (one frequency step at a time) and automatic (seeks frequencies with acceptable signal strength) tuning mode. It also toggles between stereo and mono modes when an FM station is tuned. When XM Radio is in use, pressing this button repeatedly displays the channel name, category, artist and track title in the lower line of the Message Display. For traffic-and-weather channels, this button displays the city, channel name, local weather and local temperature. Delay: Press this button to set delay times that compensate for placing the speakers at different distances from the listening position. Remote IR Sensor: This sensor receives infrared (IR) commands from the remote control. It is important to ensure that it is not blocked. If covering the sensor is unavoidable, such as when the AVR 347 is placed inside a cabinet, you may use an optional Harman Kardon HE 1000, or other infrared receiver, connecting it to the Remote IR Input on the AVR 347's rear panel. Alternatively, connect the Remote IR Output of another compatible component to the AVR 347's Remote IR Input. Point the remote at the other device's remote sensor, and the command will be transmitted to the AVR 347. An external IR "blaster" may also be used, positioned to point at this area. Preset Stations: Press this button to select a preset radio station. Headphone Jack/EzSet/EQ Microphone Input: Plug a 1/4" headphone plug into this jack for private listening. This jack is also used to connect the supplied microphone before beginning the EzSet/EQ procedure described in the Initial Setup section. To begin EzSet/EQ, plug the supplied microphone into this jack, place the microphone at the listening position, and follow the directions given in the SPEAKER SETUP-AUTO CONFIGURATION on-screen menu. 8 Message Display Speaker/Channel Input Indicators Delay Volume Channel Level Adjust Speaker Size Tone Mode Setup Surround Mode Indicators Navigation Source Indicators Remote IR Sensor Digital Input Select Power Indicator Surround Select Surround Mode Tuning Preset Stations Tuner Band Standby/On Switch Main Power Switch Headphone Jack/EzSet/EQ Microphone Input Source Tuning Select Mode Digital Audio Inputs (Optical 4 and Coaxial 4) Video 4 Video Inputs Video 4 Analog Audio Inputs NOTE: To make it easier to follow the instructions throughout the manual that refer to this illustration, a copy of this page may be downloaded from the Product Support section at www.harmankardon.com. 9 REAR-PANEL CONNECTIONS AM and FM Antenna Terminals: Connect the included AM and FM antennas to their respective terminals for radio reception. XM Antenna Jack: Plug in an XM antenna module here. The XM antenna module is purchased separately, and should specify that it is for home use with an XM Ready® product. You will need to subscribe to the XM service, which is available separately, and activate the service for your antenna module. (XM service is not available in Alaska and Hawaii.) Front, Center and Surround Speaker Outputs: Use twoconductor speaker wire to connect each set of terminals to the correct speaker. Remember to observe the correct polarity (positive and negative connections). Always connect the positive lead to the colored terminal on the receiver and the red terminal on the speaker. Connect the negative lead to the black terminal on both the receiver and the speaker. See the Connections section for more information on connecting your speakers. Surround Back/Multiroom Speaker Outputs: These speaker outputs may be used either for the surround back channels in a 7.lchannel home theater, or they may be reassigned to a remote room for use with a multiroom system. When these outputs are reassigned for multiroom operation, only a 5.1-channel configuration will be available in the main listening room. Use the on-screen menu system to configure these channels as desired. As with the other speaker outputs, remember to observe proper polarity by connecting the positive and negative output terminals to the corresponding terminals on each speaker. Remote IR Carrier Output: This output is similar in function to the Remote IR Output, with the difference that this jack outputs the full infrared signal as received by the AVR's IR sensor or the Remote IR Input, while the Remote IR Output jack outputs a "stripped" signal that has no carrier frequency. The full signal may be required by some components with IR inputs. It may also be required when you connect external IR emitters or other devices to the AVR to pass IR signals to other components. Multiroom Audio Outputs: Connect these jacks to an external amplifier to power the speakers in the remote zone of a multiroom system. When these jacks are used, it is possible to have a full 7.1channel system in the main listening room at the same time the multiroom system is in use. A-BUS Port: Use a Category 5/5e cable to connect this port to optional A-BUS equipment for multiroom operation. When the A-BUS system is used, it is possible to have a full 7.1-channel system in the main listening room at the same time the multiroom system is in use. Video 1, Video 2, Video 3 and DVD Audio/Video Inputs: These jacks may be used to connect your video-capable source components (e.g., VCR, DVD player, cable TV box) to the receiver. Remember to use only one type of video connection for each source. See the Connections section for more information on audio and video connection options for each source component. Video 1 Audio/Video Outputs: These jacks may be used to connect your VCR or another recorder. Composite and S-Video Monitor Outputs: If any of your sources use composite or S-video connections, you may need to connect one or both of these monitor outputs to the corresponding inputs on your television or video display in order to view the sources and to view the on-screen displays. If your video display is equipped with component video or HDMI inputs, you may take advantage of the AVR 347's transcoding capability, which transcodes composite and S-video signals to component video and HDMI, allowing for only a single video connection from the AVR to the video display. Subwoofer Output: If you have a powered subwoofer with a linelevel input, connect it to this jack. Preamp Outputs: Connect these jacks to an external amplifier if more power is desired. Surround Back/Multiroom Preamp Outputs: These outputs may be used with an external amplifier either to power the surround back channels, or to power the speakers in the remote zone of a multichannel system. Use the on-screen menu system to configure these channels as desired. Remote Infrared (IR) Input and Output: When the remote IR receiver on the front panel is blocked, such as when the AVR is placed inside a cabinet, connect an optional IR receiver to the Remote IR Input jack for use with the remote control. The Remote IR Output may be connected to the Remote IR Input of a compatible source device (or other product) to enable remote control through the AVR. This is particularly useful in multiroom applications, when you wish to control the source device from the remote room (when used with the Multiroom IR Input). When several source devices are used, connect them in "daisy chain" fashion. Multiroom Infrared (IR) Input: Connect a remote IR receiver located in the remote zone of a multiroom system to this jack to control the AVR and any source devices connected to the Remote IR Output from the remote zone. HDMI Inputs and Output: HDMI (High-Definition Multimedia Interface) is a newer type of connection for transmitting digital audio and video signals between devices. With the AVR 347's powerful processor, you may connect up to two HDMI-equipped source devices to the HDMI inputs using a single-cable connection, while benefiting from superior digital audio and video performance. However, if your video display is not HDMI-compatible, you will need to connect the device to one of the other source inputs, selecting a coaxial or optical digital audio input and analog video input. See the Connections and Installation sections for more information. If your video display has an HDMI input, but some of your sources have only analog video outputs, you may still rely on just the HDMI video connection to your display; the AVR 347 will automatically transcode analog video signals up to 720p to the HDMI format. High-resolution analog 1080i or higher signals are not available at the HDMI Output, but 1080i signals received through one of the HDMI Inputs will be passed through directly to the HDMI Output without any video processing. 10 REAR-PANEL CONNECTIONS The AVR 347 is Simplay HD-verified for compatibility via the HDMI connection with other Simplay HD-verified products. · Due to the design of some video displays, analog 480p or 720p component video source signals may produce artifacts when used with the AVR's analog video outputs (composite, S-video or component video). If this occurs, try changing the Video Mode setting in the INPUT SETUP menu, or connecting the source device's video output directly to your video display. However, for best results, we recommend you consider upgrading to an HDMI-capable video display. CD and Tape Audio Inputs: These jacks may be used to connect audio-only source components (e.g., CD player, tape deck). Do not connect a turntable to these jacks without a phono preamp. Tape Outputs: These jacks may be used to connect a CDR or another audio-only recorder. Coaxial and Optical Digital Audio Inputs: If a source has a compatible digital audio output, and if you are not using an HDMI connection for audio for the device, connect it to one of these jacks for improved audio performance. Use only one type of digital audio connection for each source. RS-232 Serial Port: This specialized connector may be used with your personal computer in case Harman Kardon offers a software upgrade for the receiver at some time in the future. RS-232 Mode: Leave this switch popped out in the Operate position unless the AVR 347 is being upgraded. RS-232 Reset: This switch is only used during a software upgrade. A standard processor reset is performed by pressing and holding the front-panel Tone button. Switched AC Accessory Outlet: You may plug the AC power cord of one source device into this outlet, and it will turn on whenever you turn on the receiver. Do not use a source that consumes more than 50 watts of power. Coaxial and Optical Digital Audio Outputs: If a source is also an audio recorder, you may connect a compatible digital audio output to the recorder's input for improved recording quality. The Bridge/DMP Input: Connect the optional Harman Kardon to this input for use with your iPod (not included). Make sure the receiver is turned off (in Standby mode) when connecting The Bridge. The TM Bridge 6-/8-Channel Inputs: Connect the multichannel analog audio outputs of a DVD-Audio, SACDTM, Blu-ray DiscTM or HD-DVDTM player (or any other external decoder) to these jacks to enjoy these proprietary formats. NOTE: When an HD-DVD or Blu-ray Disc player has an onboard digital decoder, it is not necessary to connect it to the 6-/8-Channel Analog Audio Inputs. Only a digital audio connection (HDMI, coaxial or optical) is needed. AC Power Cord Input: After you have made all other connections, plug the AC power cord into an unswitched outlet. Plug the female end of the cord into this receptacle, which conveniently allows you to install all wiring ahead of time. Component Video Inputs: If both a video source (e.g., DVD player or HDTV tuner) and your television or video display have analog component video (Y/Pb/Pr) capability and if you are not using HDMI connections for the device, then you may connect the component video outputs of the source to one of the two component video inputs. Do not make any other video connections to that source. Component Video Monitor Outputs: If you are using one of the Component Video Inputs and your television or video display is component-video-capable and if you are not connecting the HDMI output to our display, you may connect these jacks to the corresponding inputs on your video display. NOTES: · Due to copy-protection restrictions, there is no output at the Component Video Monitor Outputs for copy-protected sources. · High-resolution 1080i and 1080p video signals are not available at the HDMI Output, but 1080i signals are passed through, as is, to the Component Video Outputs. If your source output is analog high-resolution video, either use the AVR's Component Video Outputs, lower the output resolution of your source device, or connect your source's component video outputs directly to your video display. 11 12 Video 3 A/V Inputs Video 1 A/V Outputs DVD A/V Inputs Video Monitor Outputs RS-232 Mode HDMI 2 Input RS-232 Serial Port Video 1 A/V Inputs Video 2 A/V Inputs Component Coaxial Digital Video Audio XM Inputs Inputs Antenna RS-232 (1, 2 & 3) (1, 2 & 3) Reset Jack The Component HDMI 1 HDMI Bridge/ Output Input Video DMP Monitor Input Outputs Front Speaker Outputs 6-/8Channel Inputs Surround Speaker Outputs Coaxial Digital Audio Output Switched AC Accessory Outlet Center Speaker Outputs Optical Digital Audio Inputs (1, 2 & 3) Surround Back/ Multiroom Preamp Outputs Subwoofer Output Multiroom IR Input Remote IR Input Surround Back/Multiroom Speaker Outputs Remote IR Output Optical Digital Audio Output AC Power Cord Input Tape Outputs FM Antenna Tape Inputs AM Antenna CD Inputs Preamp Outputs Multiroom Audio Outputs A-BUS Port Remote IR Carrier Output NOTE: To make it easier to follow the instructions throughout the manual that refer to this illustration, a copy of this page may be downloaded from the Product Support section at www.harmankardon.com. MAIN REMOTE CONTROL FUNCTIONS The AVR 347 remote is capable of controlling 11 devices, including the AVR itself and an iPod docked in the optional The Bridge accessory. During the installation process, you may program the codes for each of your source components into the remote. Each time you wish to use the codes for any component, first press the Selector button for that component. This changes the button functions to the appropriate codes for that product. NOTE: Several of the Input Selectors are shared between two devices. The selector button will light in red when the remote is in the device mode printed on the button, and it will light in green for the device mode printed above the button. To switch between the two device modes, press the selector twice quickly in succession. The selector will remain in the last-selected mode until the next time you press the selector twice quickly. For example, the first time you press the DVD button, the button will light up in red, indicating that the remote is in DVD mode. If you press another selector, such as the VID3 selector, and then press the DVD button again, the DVD button will remain red, indicating the remote is still in DVD mode. Now press the DVD button twice quickly. At the first press the button will light red, indicating that the remote is in DVD mode. On the second press the button will turn green, indicating that the remote is now in CD mode. If you press a different selector and return to the DVD/CD Selector, you will observe that the remote is still in CD mode. Each Input Selector has been preprogrammed to control certain types of components, with only the codes specific to each brand and model changing, depending on which product code is programmed. The device types programmed into each selector may not be changed; however you may program the HDMI 1 and 2 selectors with the DVD, Cable/Satellite or VCR/PVR device type. IR Transmitter Lens: As buttons are pressed on the remote, infrared codes are emitted through this lens. Make sure it is pointing toward the component being operated. Power On Button: Press this button to turn on the AVR or another device. The Master Power Switch on the AVR 347's front panel must first have been switched on. Mute Button: Press this button to mute the AVR 347's speaker and headphone outputs temporarily. To end the muting, press this button or adjust the volume. Muting is also canceled when the receiver is turned off. Program Indicator: This LED lights up or flashes in one of three colors as the remote is programmed with codes. Power Off Button: Press this button to turn off the AVR 347 or another device. AVR Selector: Press this button to switch the remote to the codes that operate the receiver. Input Selectors: Press one of these buttons to select a source device, which is a component where a playback signal originates, e.g., DVD, CD, cable TV, satellite or HDTV tuner, or an iPod docked in the optional The Bridge. This will also turn on the receiver and switch the remote's mode to operate the source device. XM Radio Button: Press this button to select XM Satellite Radio as the source. You will need to have purchased and activated an XM antenna module, and you will also need to subscribe to the XM Radio service. Visit www.xmradio.com for more information. AM/FM Button: Press this button to select the tuner as the source, or to switch between the AM, FM and XM Radio bands. DVD: Controls DVD players and recorders. CD: Controls CD players and recorders. Tape: Controls cassette decks. Video 1: Controls VCRs, TiVo® and PVRs. Video 2: Controls cable and satellite television set-top boxes. Video 3: Controls televisions and other video displays. Video 4: Controls televisions and other video displays. HDMI 1 and 2: Each code set controls a source device (VCR/PVR, DVD player or cable/satellite set-top box) connected to one of these two inputs. 6-/8-Channel Input Selector: Press this button to select the 6-/8-Channel Inputs as the audio source. The receiver will use the video input and remote control codes for the last-selected video source. Learn Button: The AVR 347 remote is capable of "learning" individual IR codes from the original remote that came with your TV or a device that is connected to any of the source inputs. See the Advanced Functions section for instructions on learning remote codes. Test Tone: Press this button to activate the test tone for manual output-level calibration. TV/Video: This button has no effect on the receiver, but is used to switch video inputs on some video source components. Sleep Button: Press this button to activate the sleep timer, which turns off the receiver after a programmed period of time of up to 90 minutes. XM: Controls the AVR functions for XM Satellite Radio. The Bridge/DMP: Controls an iPod docked in The Bridge. Any given button may have different functions, depending on which component is being controlled. Some buttons are labeled with these functions. For example, the Sleep and DSP Surround Buttons are labeled for use as Channel Up/Down Buttons when controlling a television or cable box. See Table A8 in the appendix for listings of the different functions for each type of component. Volume Controls: Press these buttons to raise or lower the volume, which will be shown in decibels (dB) in the Message Display. DSP Surround: Press this button to select a DSP surround mode (Hall 1, Hall 2, Theater). 13 IR Transmitter Lens Power On Program Indicator AVR Selector AM/FM XM Radio Test Tone Sleep DSP Surround On-Screen Display Channel Level Mute Power Off Input Selectors 6-/8-Channel Input Selector Learn TV/Video Volume Controls Multiroom Speaker Setup Navigation Set Digital Input Delay Numeric Keys Tuning Mode Direct Station Entry Tuning Tone Mode Memory Clear Preset Stations Selectors Disc Skip Macros Surround Mode Selectors Dim Night Mode Track Skip Transport Controls Backlight NOTE: To make it easier to follow the instructions throughout the manual that refer to this illustration, a copy of this page may be downloaded from the Product Support section at www.harmankardon.com. 14 MAIN REMOTE CONTROL FUNCTIONS On-Screen Display (OSD): Press this button to activate the on-screen menu system. press the Set Button repeatedly until PRESET SEARCH appears. Use the // ¤ Buttons to select a letter (A through E) representing one of the five banks of preset memory slots. Then press the Memory Button, followed by a Numeric Key (1 through 8) for the precise preset memory location you wish to save the channel in. Multiroom: Press this button to control the multiroom system. Three settings are available: MULTI ON/OFF, which is used to turn the multiroom system on or off; MULTI LEVEL, which adjusts the volume of the remote zone only; and MULTI INPUT, which is used to select the source input for the remote zone. See Multiroom Operation in the Advanced Functions section for more information on using the AVR 347's multiroom system. Channel Level: Press this button to adjust the output levels for each channel so that all speakers sound equally loud at the listening position. Usually this is done while playing an audio selection, such as a favorite CD, after you have calibrated the levels using EzSet/EQ, as described in the Initial Setup section. Speaker Setup: Press this button to configure speaker sizes, that is, the low-frequency capability of each speaker. Usually this is done using the on-screen menu system, as described in the Initial Setup section. Tuning: Press these buttons to tune a radio station or XM Radio channel. For the AM and FM bands, and depending on whether the tuning mode has been set to manual or automatic, each press will either change one frequency step at a time, or seek the next frequency with acceptable signal strength. Direct: Press this button before using the Numeric Keys to directly enter a radio station frequency (AM or FM bands only). Clear: Press this button to clear a radio station frequency you have started to enter. Preset Stations Selector: Press these buttons to select a preset radio station. For XM Radio, first press the Set Button repeatedly until PRESET SEARCH appears and then use the // ¤ Buttons to select the letter of the desired bank of presets. Navigation (// ¤/ < / > ) and Set Buttons: These buttons are used to make selections within the on-screen menu system, or when accessing the functions of the four buttons surrounding this area of the remote ­ Channel Level, Speaker Setup, Digital Input or Delay. Digital Input Select: Press this button to select the specific digital audio input (or analog audio input) you used for the current source. Tone Mode: Press this button to access the tone controls (bass and treble). Use the Navigation Buttons to make your selections. Disc Skip: This button has no effect on the receiver, but is used with some optical disc changers to skip to the next disc. Delay: Press this button to set delay times that compensate for placing the speakers at different distances from the listening position, or to resolve a "lip sync" issue that may be caused by digital video processing. This may also be done using the on-screen menu system, as described in the Initial Setup section. Macros: These buttons may be programmed to execute long command sequences with a single button press. They are useful for programming the command to turn on or off all of your components, or for accessing specialized functions for a different component than you are currently operating. Surround Mode Selectors: Press any of these buttons to select a type of surround sound (e.g., multichannel) mode. Choose from the Dolby modes, DTS modes, Logic 7 modes or Stereo modes. Each press of a button will cycle to the next available variant of that mode. Not all modes or mode groups are available with all sources. Numeric Keys: Use these buttons to enter radio station frequencies or to select station presets. When the AM or FM band is in use, press the Direct button before entering the station frequency. When listening to XM Radio, you may enter channel numbers without first pressing the Direct Button; however, use the Preset Stations Selectors to access the preset stations. To access another bank of XM presets, press the Set Button repeatedly until PRESET SEARCH appears, then use the // ¤ Buttons to select the letter of the desired bank. Night Mode: Press this button to activate Night mode with specially encoded Dolby Digital discs or broadcasts. Night mode compresses the audio so that louder passages are reduced in volume to avoid disturbing others, while dialogue remains intelligible. Tuning Mode: When listening to AM or FM radio, this button toggles between manual (one frequency step at a time) and automatic (seeks frequencies with acceptable signal strength) tuning mode. It also toggles between stereo and mono modes when an FM station is tuned. When listening to XM Radio, press the Tuning Mode Button once to view the category name of the current channel. Additional presses will display the artist, song title and channel name. Track Skip: These buttons have no effect on the receiver, but are used with many source components to change tracks or chapters. Dim: Press this button to partially or fully dim the front-panel display. Transport Controls: These buttons have no effect on the receiver, but are used to control many source components. By default, when the remote is operating the receiver, these buttons will control a DVD player. Memory: After you have tuned a particular radio station, press this button, then the numeric keys, to save that station as a radio preset. For XM Radio, the procedure for saving a preset is a little different. To save the current channel in one of the 40 available preset locations, Backlight: Press this button to illuminate the buttons on the remote. Press it again to turn the backlight off, or wait five seconds after the last button press for the light to turn off on its own. 15 ZONE II REMOTE CONTROL FUNCTIONS The Zone II remote is a simplified device for use in the remote room of a multiroom system with an IR receiver connected to the Multiroom IR Input or an A-BUS device. It may be used to control the power, volume and mute functions for the remote zone; select a source input for the remote zone and control a compatible Harman Kardon DVD, CD or tape player that is connected to one of the AVR's Remote IR Outputs. The Zone II remote may also be used in the main listening room to directly control the AVR 347 and Harman Kardon DVD, CD or tape players connected to the Remote IR outputs. In that case the power, volume and mute controls will affect only the main listening area. The Zone II remote requires two AAA batteries (included) that are installed in the battery compartment on the back of the remote. Gently pull down on the tab at the top of the battery compartment cover and pull the cover off the remote. Make sure to observe proper polarity by matching the + and ­ symbols on the remote to the corresponding symbols printed inside the compartment. Input Selectors: Press one of these buttons to select a source device for the remote zone. It will also turn on the multiroom system and switch the remote to operate the source device. You may select a different source device than is in use in the main room. If you select the same source as the main room, then any commands sent to the source, such as changing radio stations or skipping tracks on a CD, will affect both zones. AM/FM/XM Radio: Press this button once to select the tuner as the source for the remote zone, which will also turn on the multiroom system. The last-used band will be active. Press the button repeatedly to switch to the desired band. In order to listen to XM Radio, you must have purchased and activated an XM antenna module and subscribed to the XM Radio service. Visit www.xmradio.com for more information. Preset Up/Down ­ Track Skip: When the tuner has been selected as the source, these buttons may be used to scroll through the radio stations previously stored as presets, as described in the Using the Tuner section. When a CD or DVD player or an iPod docked in The Bridge is in use, these buttons may be used to skip forward or backward through the tracks or chapters on a disc. IR Transmitter: This button-shaped lens emits infrared codes when buttons on the remote are pressed. Make sure it is pointing toward the IR receiver when in the remote room, or the component being operated when used in the main listening room. Power Off: Press this button to turn off the AVR 347. The Zone II remote has no Power On Button, since the AVR turns on its multiroom system automatically when any of the Input Selectors is pressed, even if the AVR itself is in Standby mode. Tuning Up/Down ­ Fast Play: When the tuner has been selected as the source, these buttons may be used to tune a radio station. They will function in auto or manual tuning mode, depending on the current status of the AVR. It is not possible to change the tuning mode from the remote room using the Zone II remote. When a CD or DVD player, tape deck or an iPod docked in The Bridge is in use, these buttons may be used to fast-play forward or backward within a track. Mute: Press this button to mute the AVR 347's remote zone speakers temporarily. To end the muting, press this button or adjust the volume, or turn off the multiroom system. Unless the remote is used in the main listening area, only the remote zone will be affected. Play, Stop, Pause: These buttons have no effect on the AVR, but may be used to operate many source devices. Disc Skip Up/Down: These buttons have no effect on the AVR or a single-disc DVD or CD player, but may be used with some disc changers to skip to another loaded disc. Volume Controls: Press these buttons to raise or lower the volume in the remote zone. AVR Selector: Press this button switch the remote to the AVR device mode. It will also turn on the multiroom system if it was off. 16 IR Transmitter Power Off AVR Selector AM/FM/XM Radio Mute Input Selectors Preset Up/Down ­ Track Skip Stop Tuning Up/Down ­ Fast Play Play Disc Skip Pause Volume Controls NOTE: To make it easier to follow the instructions throughout the manual that refer to this illustration, a copy of this page may be downloaded from the Product Support section at www.harmankardon.com. 17 INTRODUCTION TO HOME THEATER The AVR 347 may be the first multichannel surround sound receiver you have owned. Although it has more connections and features than two-channel receivers, many of the principles are similar and the new concepts are easy to understand. This introductory section will help you to familiarize yourself with the basic concepts, which will make setup and operation smoother. If you are already familiar with home theater, you may skip this section and proceed to the Connections section on page 19. your main listening area, and reassign the surround back channels for use with a multiroom system, in which you use the surround back channels to power a pair of loudspeakers located in another room. Many people expect the surround speakers to play as loudly as the front speakers. Although all of the speakers in the system will be calibrated to sound equally loud at the listening position, most artists use the surround speakers for ambient effects only, and they program their materials to steer very little sound to these speakers. · Subwoofer ­ A subwoofer is a special-purpose speaker designed to play only the lowest frequencies (the bass). It may be used to augment smaller, limited-range satellite speakers used for the other channels. In addition, many digital-format programs, such as movies recorded in Dolby Digital, contain a special low-frequency effects (LFE) channel which is directed only to the subwoofer. The LFE channel packs the punch of a rumbling train or airplane, or the power of an explosion, adding realism and excitement to your home theater. Many people use two subwoofers, placed on the left and right sides of the room, for additional power and even distribution of the sound. Typical Home Theater System A home theater typically includes your audio/video receiver, which controls the system; a DVD player; a source component for television broadcasts, which may be a cable box, a satellite dish receiver, an HDTV tuner or simply an antenna connected to the TV; a video display (television); and loudspeakers. All of these components are connected using various types of cables for audio and video signals. Multichannel Audio The main benefit of a home theater system is that several loudspeakers are used in various locations around the room to produce "surround sound." Surround sound immerses you in the musical or film presentation for increased realism. The AVR 347 may have up to seven speakers connected directly to it (plus a subwoofer). Each main speaker is powered by its own amplifier channel inside the receiver. When more than two speakers are used, it is called a multichannel system. · Front Left and Right ­ The main speakers are used the same way as in a 2-channel system. However, you may notice that in many surround modes, these speakers are used more for ambient sound while the main action, especially dialogue, is moved to the center speaker. · Center ­ The center speaker is usually placed above or below the video screen, and is used mostly for dialogue in movies and television programs. This placement allows the dialogue to originate near the actors' faces, for a more natural sound. · Surround Left and Right ­ The surround speakers are used to improve directionality of ambient sounds. In addition, by using more loudspeakers in the system, more dynamic soundtracks may be played without risk of overloading any one speaker. · Surround Back Left and Right ­ Additional surround speakers may be placed behind the listening position, improving the precision with which ambient sounds may be placed and allowing for more realistic-sounding pans. By using more speakers in the system, the same sound levels may be attained with less burden placed on any individual speaker. The surround back speakers may also be used with specialized surround modes that are designed for use with 7.1-channel systems, such as Dolby Digital EX, DTS-ES (Discrete and Matrix) and Logic 7 (7.1 modes). However, the surround back speakers are optional. In fact, the AVR 347 enables you to set up a 5.1-channel system in Surround Modes There are different theories as to the best way to present surround sound and to distribute soundtrack information among the various speakers. A variety of algorithms have been developed in an effort to accurately reproduce the way we hear sounds in the real world. The result is a rich variety of surround mode options. Some modes are selected automatically, depending on the signal being received from the source. In many cases, you may select a surround mode manually. Several companies have taken surround sound in slightly differing directions. It is helpful to group the numerous surround modes either by their brand name, or by using a generic name: · Dolby Laboratories, Inc. Modes ­ Dolby Digital, Dolby Digital EX, Dolby Pro Logic II and IIx, Dolby Virtual Speaker, Dolby Headphone · DTS Modes ­ DTS, DTS-ES (Discrete and Matrix), DTS Neo:6, DTS 96/24 · Harman International (Harman Kardon's Parent Company) ­ Logic 7 · DSP Modes ­ Generic modes that include Hall 1, Hall 2 and Theater · Stereo Modes ­ Generic modes that expand upon conventional 2-channel stereo, including DSP Surround Off, Analog Bypass Surround Off and 5- and 7-Channel Stereo Table 8 on pages 50­52 contains detailed explanations of the differences between the various mode groups, and the mode options available within each group. Digital modes, such as Dolby Digital and DTS, are only available with specially encoded programs, such as HDTV, DVDs and digital cable or satellite television. Other modes may be used with various digital and analog signals to create a different surround presentation, or to use a different number of speakers. Surround mode selection depends upon the number of speakers in your system, the materials you are watching or listening to, and your personal tastes. Feel free to experiment. 18 18 CONNECTIONS There are different types of audio and video connections used to connect the receiver to the speakers and video display, and to connect the source devices to the receiver. To make it easier to keep them all straight, the Consumer Electronics Association (CEA®) has established a color-coding standard. Table 1 may be helpful to you as a reference while you set up your system. Table 1 ­ Connection Color Guide Audio Connections Left Front (FL/FR) Center (C) Surround (SL/SR) Surround Back (SBL/SBR) Subwoofer (SUB) Right Bare wire cables are installed as follows (see Figure 2): 1. Unscrew the terminal cap until the pass-through hole in the collar is revealed. 2. Insert the bare end of the wire into the hole. 3. Hand-tighten the cap until the wire is held snugly. 1 Input Output 2 3 Digital Audio Connections Coaxial Optical Figure 2 ­ Binding-Post Speaker Terminals With Bare Wires Video Connections Component Composite S-Video Y Pb Pr Subwoofer The subwoofer is a specialized type of loudspeaker that is usually connected in a different way. The subwoofer is used to play only the low frequencies (bass), which require much more power than the other speaker channels. In order to obtain the best results, most speaker manufacturers offer powered subwoofers, in which the speaker contains its own amplifier on board. Sometimes the subwoofer is connected to the receiver using the front left and right speaker outputs, and then the front left and right speakers are connected to terminals on the subwoofer. More often, a line-level (nonamplified) connection is made from the receiver's Subwoofer Output to a corresponding jack on the subwoofer, as shown in Figure 3. Although the subwoofer output looks similar to the analog audio jacks used for the various components, it is filtered and only allows the low frequencies to pass. Don't connect this output to any other devices. Although doing so won't cause any harm, performance will suffer. HDMI Connections (digital audio/video) TM HDMI Types of Connections This section will briefly review different types of cables and connections that you may use to set up your system. Speaker Connections Speaker cables carry an amplified signal from the receiver's speaker terminals to each loudspeaker. Speaker cables contain two wire conductors, or leads, inside plastic insulation. The two conductors are usually differentiated in some way, by using different colors, or stripes, or even by adding a ridge to the insulation. Sometimes the actual wires are different, one being copper-colored and the other silver. The differentiation is important because each speaker must be connected to the receiver's speaker-output terminals using two wires, one positive (+) and one negative (­), referred to as speaker polarity. It's important to maintain the proper polarity for all speakers in the system. If some speakers have their negative terminals connected to the receiver's positive terminals, performance can suffer, especially for the low frequencies. Always connect the positive terminal on the loudspeaker, which is usually colored red, to the positive terminal on the receiver, which is colored as shown in the Connection Color Guide (Table 1). Similarly, always connect the black negative terminal on the speaker to the black negative terminal on the receiver. The AVR 347 uses binding-post speaker terminals that can accept banana plugs or bare-wire cables. Banana plugs are simply plugged into the hole in the middle of the terminal cap. See Figure 1. Preout Subwoofer Figure 3 ­ Subwoofer Connecting Source Devices to the AVR The AVR 347 is designed to process audio and video input signals, playing back the audio and displaying the video on a television or monitor connected to the AVR. These signals originate in what are known as "source devices," including your DVD player, CD player, DVR (digital video recorder) or other recorder, tape deck, game console, cable or satellite television box or MP3 player. Although the tuner is built into the AVR, it also counts as a source, even though no external connections are needed, other than the FM and AM antennas and the XM antenna module. Separate connections are required for the audio and video portions of the signal, except for digital HDMI connections. The types of connections used depend upon what's available on the source device, and for video signals, the capabilities of your video display. + Figure 1 ­ Binding-Post Speaker Terminals With Banana Plugs 19 19 CONNECTIONS Audio Connections There are two formats for audio connections: digital and analog. Digital audio signals are of higher quality, and are required for listening to sources encoded with digital surround modes, such as Dolby Digital and DTS. There are three types of digital audio connections: HDMI, coaxial and optical. Any one type of digital audio connection may be used for each source device, but never more than one for the same source. However, it's okay to make both analog and digital audio connections at the same time to the same source. NOTE: Since the AVR 347 is capable of processing the audio and video portions of most HDMI signals, if your video display device has an HDMI input, you may make a single HDMI connection from your HDMI 1.1-or-higher source device (such as a DVD player) to the AVR. In that case, no separate digital audio connection is required. Make sure to turn the volume on your television all the way off. IMPORTANT NOTE: The AVR 347 cannot convert 1080i or 1080p analog video signals to the HDMI format, but passes 1080i signals in their native format to the Component Video Outputs. This affects users of Microsoft® Xbox® 360 systems and some older set-top boxes. If your digital cable television set-top box outputs 1080i or better video via component video outputs and is not equipped with an HDMI output, contact your cable operator for a replacement. For Xbox 360 and satellite television customers, either change the settings on your source device to ensure that it outputs only 720p video through its component video outputs, which the AVR can convert to the HDMI format, or connect the AVR's Component Video Monitor Outputs to the video display. Although you could connect the source device's component video outputs directly to your video display, you would then have to select the correct video input on the display, depending on which source input on the AVR was in use. The physical HDMI connection is simple. The connector is shaped for easy plug-in (see Figure 4). If your video display has a DVI input, you may use an HDMI-to-DVI adapter (not included) to connect it to the AVR's HDMI Output. Digital Audio The AVR 347 is equipped with two HDMI (High-Definition Multimedia Interface) inputs, and one output. HDMI is capable of carrying digital audio and video information using a single cable, thus delivering the highest possible quality picture and sound. The AVR 347 is Simplay HD-verified for compatibility via the HDMI connection with other Simplay HD-verified products. There are different versions of HDMI, depending on the capability of the source device and the type of signal it is capable of transmitting via the HDMI connection. In addition, receivers and processors such as the AVR 347 may handle the incoming signal in several different ways, depending on their capability as well. The AVR 347 uses HDMI version 1.1, and is capable of processing both the audio and video components of the HDMI data, minimizing the number of cable connections in your system. NOTE: Some multichannel audio devices, such as DVD-Audio, SACD, HD-DVD or Blu-ray Disc players, output some audio formats only through the source's multichannel analog outputs. These include DVD-Audio players with HDMI version 1.0, and HD-DVD and Blu-ray Disc players that do not decode the digital audio. In those cases, make a separate analog audio connection in addition to the HDMI connection, which is still used for video or if you wish to listen to Dolby Digital, DTS or PCM materials that may be stored on the disc. In addition, the AVR 347 will convert analog video signals to the HDMI format, upscaling to high-definition 720p resolution. Source signals with 1080i or 1080p resolution are passed via the HDMI Output to your display at their original high-quality resolution, depending on your display's capabilities. You may view the AVR 347's own on-screen display menus using the HDMI output. Figure 4 ­ HDMI Connection HDMI cable runs are usually limited to about 10 feet. The AVR 347 incorporates a repeater, which allows an additional 10 feet of cable between the source device and the video display. If your video display or source device is not HDMI-capable, use one of the analog video connections (composite, S- or component video) and if available on your source device, either a coaxial or optical digital audio connection. Coaxial digital audio jacks are usually color-coded in orange. Although they look similar to analog jacks, they should not be confused, and you should not connect coaxial digital audio outputs to analog inputs or vice versa. See Figure 5. Coaxial digital audio cable Figure 5 ­ Coaxial Digital Audio Coaxial Optical digital audio connectors are often covered by a shutter to protect them from dust. The shutter opens as the cable is inserted. Input connectors are color-coded using a black shutter, while outputs use a gray shutter. See Figure 6. Optical digital audio cable Optical Figure 6 ­ Optical Digital Audio Due to the nature of digital signals as binary bits, they aren't subject to signal degradation the way analog signals are. Therefore, the quality of all digital audio connections should be the same, although it is important to limit the length of the cable. Whichever type of connection you choose, Harman Kardon recommends that you always select the highest quality cables available within your budget. 20 20 CONNECTIONS Analog Audio Analog connections require two cables, one for the left channel (white) and one for the right channel (red). These two cables are often attached to each other for most of their length. See Figure 7. Most sources that have digital audio jacks also have analog audio jacks, although some older types of sources, such as tape decks, have only analog jacks. For sources that are capable of both digital and analog audio, you may wish to make both connections. The analog audio connection is strongly recommended if you intend to use the source with the multiroom system. It's required if you will be using the multiroom preamp outputs with an external amplifier to power your remote speakers, as the AVR 347's multiroom system is not capable of converting the digital signal to analog format. It's suggested that you also use the analog audio connections when using the surround back/multiroom speaker outputs, in case another two-channel digital audio source is in use in the main listening area. The AVR 347 is only capable of processing one PCM source at a time. If you wish to record materials from DVDs or other copy-protected sources, you may only do so using analog connections. Remember to comply with all copyright laws, if you choose to make a copy for your own personal use. Analog audio cable (RCA) L R AVR 347 remote to control the iPod, with navigation messages displayed on the front panel and on a video display connected to the AVR. The Bridge outputs analog audio to the AVR 347, and it is available to the multiroom system. Figure 9 ­ The Bridge Video Connections Although some sources produce an audio signal only (e.g., CD player, tape deck), many sources output both audio and video signals (e.g., DVD player, cable television box, HDTV tuner, satellite box, VCR, DVR). In addition to the audio connection, you will need to connect one type of video connection for each source (never more than one at the same time for any source). Digital Video If you have already connected a source device to one of the HDMI inputs as explained in the Digital Audio Connections section, then you have automatically made a video connection at the same time, as the HDMI signal includes both digital audio and video components. If the source device is not capable of transmitting its digital audio signal through the HDMI connection, then use one of the coaxial or optical digital audio inputs for the source. If a multichannel analog audio connection is required for certain lossless formats (e.g., DVD-Audio, SACD, HD-DVD or Blu-ray Disc), you may make both audio connections, but you must also make an analog video connection. To listen to the multichannel disc, first select the analog video source input, then select the 6-/8-channel analog audio inputs, and the AVR will retain the last video source you selected other than HDMI. The AVR 347 is Simplay HD-verified for compatibility via the HDMI connection with other Simplay HD-verified products. Figure 7 ­ Analog Audio Multichannel analog connections are used with some high-definition sources where the copy-protected digital content is decoded inside the source. These types of connections are usually used with DVD-Audio, SACD, Blu-ray Disc, HD-DVD and other multichannel players. See Figure 8. However, the multichannel analog audio connection is not required for DVD-Audio players compliant with HDMI version 1.1 or better, or HD-DVD and Blu-ray Disc players that decode the digital audio internally and output linear PCM signals in digital format. Consult the owner's guide for your disc player for more information. Figure 4 (repeated) ­ HDMI Connection Front Surround Center Multichannel analog audio cable (RCA) Subwoofer Analog Video There are three types of analog video connections: composite video, S-video and component video. Composite video is the basic connection most commonly available. The jack is usually color-coded yellow, and looks like an analog audio jack, although it is important never to confuse the two. Do not plug a composite video cable into an analog or coaxial digital audio jack, or vice versa. Both the chrominance (color) and luminance (intensity) components of the video signal are transmitted using a single cable. See Figure 10. Composite video cable Figure 8 ­ Multichannel Analog Audio Harman Kardon receivers also include a proprietary, dedicated audio connection called "The Bridge/DMP". If you own an iPod with a dock connector, you may separately purchase The Bridge and connect it to The Bridge/DMP port on the receiver. See Figure 9. Dock your iPod (not included) in The Bridge, and you may listen to your audio materials through your high-performance audio system. If your iPod is photoor video-capable, you may view still images or video materials stored on the iPod using your home theater system. You may even use the 21 Figure 10 ­ Composite Video S-video, or "separate" video, transmits the chrominance and luminance components using separate wires contained within a single cable. The 21 CONNECTIONS plug on an S-video cable contains four metal pins, plus a plastic guide pin. Be careful to line up the plug correctly when you insert it into the jack on the receiver, source or video display. See Figure 11. S-video cable Figure 11 ­ S-Video The AM loop antenna needs to be assembled. Then connect the two leads to the screw terminals on the receiver. See Figure 14. Component video separates the video signal into three components ­ one luminance ("Y") and two sub-sampled color signals ("Pb" and "Pr") ­ that are transmitted using three separate cables. The "Y" cable is colorcoded green, the "Pb" cable is colored blue and the "Pr" cable is colored red. See Figure 12. Component video cable Figure 14 ­ AM Antenna RS-232 Serial Port The RS-232 serial port on the AVR 347 is used only for data. If Harman Kardon releases a software upgrade for the receiver's operating system at some time in the future, the upgrade may be downloaded to the AVR using this port. Complete instructions will be provided at that time. Figure 12 ­ Component Video If it's available on your video display, HDMI is recommended as the best quality connection, followed by component video, S-video and then composite video. NOTES: · Due to copy-protection restrictions, there is no output at the Component Video Monitor Outputs for copy-protected sources. · High-resolution 1080i and 1080p video signals are not available at the HDMI Output, but 1080i signals are passed through, as is, to the Component Video Outputs. If your source outputs analog high-resolution video, either use the Component Video Outputs, change the output resolution of your source device to 720p, or connect your source's component video outputs directly to your video display. · Due to the design of some video displays, analog 480p or 720p component video source signals may produce artifacts when used with the AVR's analog video outputs (composite, S-video or component video). If this occurs, try changing the Video Mode setting in the INPUT SETUP menu, or connecting the source device's video output directly to your video display. However, for best results, we recommend that you consider upgrading to an HDMI-capable video display. Antennas The AVR 347 uses separate terminals for the included FM and AM antennas that provide proper reception for the tuner. The FM antenna uses a 75-ohm F-connector. See Figure 13. Figure 13 ­ FM Antenna 22 22 SPEAKER PLACEMENT Before you begin to connect cables, it is important to place your speakers in their correct locations in the room. Optimally, the speakers should be placed in a circle with the listening position at its center. The distance from the listening position to the video display forms the radius of the circle. The speakers should be angled so that they directly face the listening position. Placement of Surround Speakers in a 7.1-Channel System In a 7.l-channel system, the side surround speakers are placed 90 degrees from the center speaker, directly to either side of the listening position, which is different than in a 5.1-channel system. The surround back left and right speakers are placed 150 degrees from the center speaker, or directly facing the opposite-side front speaker. See Figure 16. SUB C FL 30° 30° Front Speaker Placement The center speaker is placed either on top of, below or mounted on the wall above or below the video display screen. The front left and right speakers are placed along the circle, about 30 degrees from the center speaker and angled toward the listener. It is best to place the front left/right and center speakers as close to the same height as possible, preferably at about the same height as the listener's ears. In any event, the center speaker should be no more than two feet above or below the left/right speakers. Placement of the surround speakers depends on the number of speakers in your system. If you're using only two speakers with the AVR 347, place them in the front left and right positions, and skip to the Installation section. However, Harman Kardon recommends using the AVR 347 in a 5.1- or 7.1-channel configuration for optimal surround sound performance. SUB C FL 30° 30° FR SL 90° 150° 150° 90° SR SBL SBR Figure 16 ­ Speaker Placement (7.1-Channel System) FR 110° 150° 150° 110° SL SR NOTE: Some speaker manufacturers offer 6.1-channel speaker systems, which are compatible with the 6.1-channel digital surround sound formats available on DVD and elsewhere, such as Dolby Digital EX and DTS-ES Discrete and Matrix modes. We do not recommend using the AVR 347 in a 6.1-channel configuration. In fact, the 6.1-channel formats will sound better when played through a 7.1-channel system. The same surround back channel information is played through both surround back speakers, but with twice the power and clarity. If you wish to use the AVR 347 with a 6.1-channel speaker system, place the single surround back speaker directly behind the listener, but do not connect it until after you have run the EzSet/EQ procedure for a 5.1-channel system. After EzSet/EQ finishes, connect the surround back speaker to the Surround Back Left Speaker Output. You will then need to follow the directions in the Advanced Features section for manual setup of the surround back speaker. Alternate placement for Side Surround Left Speaker Alternate placement for Side Surround Right Speaker Subwoofer Placement The subwoofer's location is less critical, since low-frequency sounds are omnidirectional. Placing the subwoofer close to a wall or in a corner will reinforce the low frequencies, and may create a "boomy" sound. You may wish to experiment over time by placing the subwoofer where the listener normally sits and then walking around the room until the low frequencies sound best. Place the subwoofer in that spot. NOTE: Your receiver will sound its best when the same model loudspeaker is used for all positions (other than the subwoofer). If that isn't possible, try to use speakers made by the same manufacturer. 23 Figure 15 ­ Speaker Placement (5.1-Channel System) Placement of Surround Speakers in a 5.1-Channel System The side surround speakers should be placed 110 degrees from the center speaker; that is, slightly behind and angled toward the listener. If this isn't feasible, place them behind the listener, with each surround speaker facing the opposite-side front speaker. See Figure 15. The surround speakers may be placed a little higher than the listener's ears. INSTALLATION You are now ready to connect your various components to your receiver. Before beginning, make sure that all components, including the AVR 347, are turned completely off and their power cords are unplugged. Don't plug any of the power cords back in until you have finished making all of your connections. Remember that your receiver generates heat while it is on. Select a location that leaves several inches of space on all sides of the receiver. It is preferable to avoid completely enclosing the receiver inside a cabinet. It is also preferable to place components on separate shelves rather than stacking them directly on top of the receiver. Some surface finishes are delicate. Try to select a location with a sturdy surface finish. Step Three ­ Connect the Antennas Connect the FM and AM antennas to their terminals. If you have purchased an XM antenna module designed for connection to an XM Ready device, such as the AVR 347, you may connect it now. To enjoy XM Radio, remember to purchase a subscription and activate your antenna module. More information is available at www.xmradio.com.See Figure 19. AVR 347 Step One ­ Connect the Speakers If you have not yet done so, place your speakers in the listening room, as described in the Speaker Placement section above. Connect the center, front left, front right, surround left, surround right, surround back left and surround back right loudspeakers to the corresponding speaker terminals on the AVR 347. See Figure 17. Remember to maintain the proper polarity by always connecting the positive and negative terminals on each speaker to the positive and negative terminals on the receiver. Use the Connection Color Guide on page 19 as a reference. AM FM Figure 19 ­ Antenna Connections Step Four ­ Connect the Source Components Use the Table A4 worksheet in the Appendix to note which connections you will use for each of your source devices. For each source, select a source input (Video 1, Video 2, Video 3, etc.). In Table 2 we recommend connecting certain types of sources to certain source inputs to make it easier to program and use the remote control. Decide which audio connections you will use. If your source device has them, use one of the HDMI, coaxial digital or the optical digital audio connection. Referring to Table 2, we recommend that you connect the DVD source to the Coaxial 1 input jack, and the source designated Video 2 to the Optical 1 input jack. If you are using the HDMI inputs, then in most cases no other audio connection is required. If your source outputs video but not audio via its HDMI connection, then select any available digital audio input on the AVR to use with the source. If your HDMI source plays DVD-Audio, SACD, HD-DVD, Blu-ray Discs or another multichannel audio format, connect its multichannel analog audio outputs to the AVR 347's 6-/8-Channel Inputs, and connect one of its analog video outputs to a source input on the AVR 347 (e.g., Component Video 3 or Video 3). When you select that source input, e.g., Video 3, select the 6-/8-Channel Inputs, and the AVR will automatically use the analog video input. NOTE: The multichannel analog audio connection is not required for DVD-Audio players compliant with HDMI version 1.1 or better, or HD-DVD and Blu-ray Disc players that decode the digital audio internally and output linear PCM signals in digital format. Consult the owner's guide for your disc player for more information. In addition to the digital audio connections, we recommend that you connect the analog audio connections for each source, as a backup to the digital connections, for recording, for use with the multiroom system, or in the event that you use all eight of the digital audio inputs for other devices. For sources that don't have digital audio outputs, you must use the analog audio connections. 24 AVR 347 C FR FL SBR SBL SR SL Figure 17 ­ Speaker Connections NOTE: If you only have one surround back speaker, wait until after you have run EzSet/EQ in the Initial Setup section before connecting it to the Surround Back Left speaker outputs. Step Two ­ Connect the Subwoofer Connect the Subwoofer Output on the AVR 347 to the line-level input on your subwoofer. See Figure 18. Consult the manufacturer's guide for the subwoofer for additional information. AVR 347 SUB Figure 18 ­ Subwoofer Connection 24 INSTALLATION For each video source, select one type of video connection. HDMI video is preferred, but both your source device and your video display must have this type of video capability. If either device does not, then use component video, S-video or composite video. Referring to Table 2, we recommend that you connect the DVD source to the Component Video 1 inputs, the Video 1 source to the Component Video 2 inputs, and the Video 2 source to the Component Video 3 inputs. Any HDMI-capable source devices should be connected to one of the two HDMI inputs. All other source devices should be connected to either the component, S- or composite video input for that source. However, you may make whatever video connections are best for your system. Table 2 ­ Recommended Source Component Connections Source Device Type VCR, DVR, PVR, TiVo or other audio/video recorder AVR 347 Source Input Video 1 Audio Connections · Video 1 Analog (inputs and outputs) and · Any one available coaxial or optical digital, audio input, with corresponding coax or optical digital output · Video 2 Analog Inputs and · Optical 1 Input Video Connections · One of Component Video 2, Video 1 S-video or Video 1 Composite Video Input · For recording, use Video 1 S-video or Composite Video Output, and do not use component video connections at all · One of Component Video 3, Video 2 S-video or Video 2 Composite Video Input NOTE: It's possible for a source to use none of the connections named for that source. For example, you might connect your DVD player to the Component Video 1 inputs and the Coax 1 digital audio input. However, we will refer to this source as "DVD," and in the Initial Setup section you will program the receiver so that these connections are assigned to the DVD source. When you select "DVD" as your source using the front panel or the remote, the correct connections for your DVD player will be used. We recommend connecting your various sources using the connections shown in Table 2 (below) in order to simplify programming your receiver and remote control. However, you may connect any device to any source input. Cable TV, satellite TV, HDTV or other device that delivers television programs Video 2 TV or other audio/video Video 3 device (only when used as a source) TV, game console, camera or other audio/video device DVD Audio/Video, SACD, HD-DVD, Blu-ray Disc Video 4 (front-panel jacks) · Video 3 Analog Inputs and · Any one available coaxial or optical digital audio input · Video 4 Analog Inputs and · Either Coax 3 or Optical 3 Input · DVD Analog Inputs · 6-/8-Channel Inputs (optional) and · Coax 1 Input · HDMI 1 Input · 6-/8-Channel Inputs (optional) · Video 3 S-video or Video 3 Composite Video Input · Not required if source is a TV · Video 4 S-video or Video 4 Composite Video Input · Not required if source is a TV · Component Video 1 Input DVD HDMI-capable DVD HDMI 1 Audio/Video or HD-DVD player or other audio/ video device HDMI-capable DVD HDMI 2 Audio/Video or HD-DVD player or other audio/ video device CD player CD · HDMI 1 Input · HDMI 2 Input · 6-/8-Channel Inputs (optional) · HDMI 2 Input · CD Analog Inputs and · Any one available coaxial or optical digital audio input · Tape Analog (inputs and outputs) and · Any one available coaxial or optical digital, audio input, with corresponding output or optical digital output · Not required CDR, MiniDisc, cassette Tape · Not required 25 INSTALLATION NOTE: The AVR 347 is equipped with a total of eight digital audio inputs, not including the HDMI inputs: six on the rear panel (Coaxial 1, 2 and 3, Optical 1, 2 and 3) and two on the front panel (Coaxial 4 and Optical 4). However, there are a total of nine sources that may be connected to devices that have digital audio outputs. We recommend certain digital audio connections simply because, as reflected in Table A1 of the Appendix, those digital audio inputs are assigned to those sources by default at the factory. But any digital audio input (except HDMI) may be reassigned to any source. Since you may not be using all nine source inputs, you may reassign a digital audio input that is recommended for a source you aren't using to another device. Table 2 is a guide; you may need to make adjustments to fit your system. Figure 21 ­ Video 2 A/V, Digital Audio and Component Video Inputs Video 3 Source The Video 3 source is used for playback only. The remote control is programmed to operate a TV, but you may connect any audio/video source device to the Video 3 inputs and use the device's own remote to control it. If you receive your television programming using your TV with an antenna or direct cable connection, connect the analog audio outputs (if available on your TV) to the Video 3 Analog Audio inputs. See Figure 22. Do not connect any video output on the television set to any video input on the receiver. See Step Five for information on connecting the receiver's video monitor outputs to the TV. NOTE: You may connect any video source other than a display device to the Video 3 S-video or composite video inputs. Video 1 Source Since this source includes audio and video recording output jacks, it is best suited to a video recorder, such as your VCR or DVR/PVR. Referring to Table 2, connect your recorder to the Video 1 Analog Audio inputs and outputs and to any available coaxial or optical digital audio input (and corresponding digital audio output). See Figure 20. Use either the Video 1 S-video or composite video input and output if you wish to make recordings. If you don't plan on recording, you may use the Component Video 2 inputs. Figure 22 ­ Video 3 A/V Inputs Video 4 Source Figure 20 ­ Video 1 A/V Inputs and Outputs, and Digital Audio Inputs and Outputs Remember to connect the audio and video output jacks on your recorder to the Video 1 or digital audio input jacks on the AVR, and the audio and video input jacks on your recorder to the Video 1 or digital audio output jacks on the AVR. NOTE: It isn't possible to make recordings using component video or HDMI connections. Keep this in mind as you connect other source devices that you may wish to make recordings from. The Video 4 source is used only for playback. It is also generally reserved for components that are only temporarily connected to the receiver, such as cameras and game consoles. When not in use, you may place the supplied covers over the front-panel Video 4 jacks for a cleaner appearance. Simply snap the covers in place. When you wish to use the jacks, gently press on the left side of each cover to pivot it out for removal. Referring to Table 2, connect your camera or game console to the Video 4 Analog Audio inputs and to either the Coaxial 4 or Optical 4 digital audio input. Connect the component's S-video or composite video output to the matching Video 4 video input. See Figure 23. Video 2 Source The Video 2 source is used only for playback. The AVR 347 remote control is programmed to operate many brands and models of cable and satellite television devices, and we recommend connecting your cable or satellite set-top box to this source. Referring to Table 2, connect your set-top box to the Video 2 Analog Audio inputs and to the Optical 1 Digital Audio input. If possible, use the Component Video 3 inputs. Otherwise, connect the set-top box's S-video or composite video output to the matching Video 2 video input. See Figure 21. 26 Figure 23 ­ Video 4 A/V and Digital Audio Inputs NOTE: The Video 4 Input Selector on the remote may be programmed to operate a television or video display only. 26 INSTALLATION IMPORTANT NOTE FOR MICROSOFT® XBOX® 360 USERS: The Microsoft Xbox 360 gaming system is capable of outputting high-definition 1080i and 1080p video signals using the analog component video outputs. Since the AVR 347 is not capable of converting these analog component video signals to the HDMI format, although 1080i signals are passed through, as is, to the Component Video Outputs, to view your Xbox 360's video output, connect the AVR's or Xbox's component video outputs to your video display, or change your Xbox 360's settings so that it outputs 720p video, which the AVR 347 can then convert to the HDMI format. Content Protection) in order to display copy-protected materials. If the source device is not capable of outputting digital audio via its HDMI output, connect its coaxial or optical digital audio output to an available input on the AVR. If the source device plays multichannel discs (e.g., DVD-Audio, SACD, HD-DVD, Blu-ray Disc), connect its multichannel analog audio outputs to the AVR 347's 6-/8-Channel Inputs (but see the note that follows Figure 25). Connect one of the source's analog video outputs to a source input on the AVR (e.g., Component Video 3 or Video 3) and select that source input, then select the 6-/8-Channel Inputs for audio; the AVR 347 will retain the last video selection other than HDMI. See Figure 26. The AVR 347 is Simplay HD-verified for compatibility via the HDMI connection with other Simplay HD-verified products. If your video display is equipped with a DVI (Digital Video Interface) input, you may use an HDMI-to-DVI adapter (not included). DVD The DVD source is used for a DVD player. If you have a more advanced multichannel device, such as a Blu-ray Disc or HD-DVD player, you may connect it to the DVD source, or to one of the HDMI sources. Referring to Table 2, connect your DVD player to the DVD Analog Audio inputs and to the Coaxial 1 Digital Audio input. If possible, use the Component Video 1 inputs. Otherwise, connect the DVD player's S-video or composite video output to the matching DVD video input. See Figure 24. Figure 26 ­ HDMI and Digital Audio Inputs CD The CD source is used for a strictly audio device, such as a CD player. Referring to Table 2, connect your CD player to the CD Analog Audio inputs and to any available digital audio input. See Figure 27. Figure 24 ­ DVD A/V, Digital Audio and Component Video Inputs If your DVD player plays multichannel lossless discs, such as SACD or DVD-Audio, or when an HD-DVD or Blu-ray Disc player is used, you may also need to connect the 6- or 8-channel analog audio outputs on the player to the 6-/8-channel analog audio inputs on the receiver, in order to enjoy these discs to their fullest. See Figure 25. Figure 27 ­ CD Audio Inputs and Digital Audio Inputs No video connections are needed. Tape The Tape source is used for audio-only recorders, such as a CDR, MiniDisc or cassette deck. Figure 25 ­ 6-/8-Channel Analog Audio Inputs NOTE: The multichannel analog audio connection is not required for DVD-Audio players compliant with HDMI version 1.1 or better, or HD-DVD and Blu-ray Disc players that decode the digital audio internally and output linear PCM signals in digital format. Consult the owner's guide for your disc player for more information. Referring to Table 2, connect your recorder to the Tape Analog Audio inputs and outputs, and to any available digital audio input (and corresponding digital audio output). See Figure 28. Figure 28 ­ Tape Audio Inputs and Outputs, and Digital Audio Inputs and Outputs HDMI 1 and 2 The HDMI sources are used with devices that are capable of outputting digital, audio and video through an HDMI connection, such as an HD-DVD or Blu-ray Disc player or HDTV tuner. The HDMI 1 and 2 sources are not used with any of the 2-channel analog audio or video inputs on the AVR 347. Make sure your video display is HDMI-capable, and for many source devices, the display must be HDCP-compliant (High-Bandwidth Digital Remember to connect the output jacks on your recorder to the Tape or digital audio input jacks on the AVR, and the input jacks on your recorder to the Tape or digital audio output jacks on the AVR. No video connections are needed. The Bridge TM With Harman Kardon's optional The Bridge, you can listen to audio or view videos stored on your iPod (not included), use your AVR 347 27 INSTALLATION