English HP SureStore CDWriter Plus User's Guide Hewlett-Packard Company, 800 S. Taft Ave., Loveland, CO 80537 C4415-XXXX Copyright 1999. Hewlett-Packard Company. All rights reserved. Hewlett-Packard is a registered trademark of the Hewlett-Packard Company. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. Pentium is a U.S. registered trademark of Intel Corp. Names of products mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective company. English-1 English-2 Product Certifications UL, cUL, TÜV, CE, C-Tick, meets or exceeds FCC Class B Requirements Laser: CDRH Laser Safety This unit employs a laser. Do not remove the cover or attempt to service this device when connected due to the possibility of eye damage. Laser-Sicherheit In das Gerät ist ein Laser eingebaut. Nehmen Sie die Abdeckung nicht ab und versuchen Sie nicht, das Gerät zu reparieren, solange es angeschlossen ist. Es besteht die Gefahr einer Augenverletzung. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser radiation exposure. WARNUNG Die Vornahme von Regelungen oder Einstellungen oder die Durchführung von Verfahren, die nicht in diesem Dokument angegeben sind, kann eine gefährliche Einwirkung von Laserstrahlung zur Folge haben. Class 1 Laser Product Klass 1 Laserapparat Luokan 1 Laserlaite Klasse 1 Laser-Produkt DANGER: INVISIBLE LASER RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM. DANGER: RADIATIONS INVISIBLES DU LASER EN CAS D'OUVERTURE. EVITER TOUT EXPOSITION DIRECTE AU FAISCEAU. VORSICHT: UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETZEN. ADVARSEL: USYNLIG LASERSTRÅLING VED ÅBNING. UNDGÅ UDS/ETTELSE FOR STRÅLING. ADVARSEL: USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES. UNNGÅ EKSPONERING FOR STRÅLEN. VARNING: OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG. VARO! NÄKYMÄTÖN AVATTAESSA OLET ALTTIINA LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEN. Laser Type: Semiconductor laser GaAlAs Wave length: 778~787 nm (at 25°C) Output power: 2.5 mW (read), 35 mW (write) Beam divergence: 60 degrees Notice Europe: This drive shall be installed only with an EN60950 (IEC950) approved power supply. USA/Canada: This drive is for use only with IBM compatible UL listed personal computers, weighing less than 18 kg. English-3 Federal Communications Commission R.F. Interference Statement WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: s s s s English Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION: Changes or modifications to this equipment not expressly approved by HewlettPackard could result in violation of Part 15 of the FCC rules. DECLARATION OF CONFORMITY according to ISO/IEC Guide 22 and EN 45014 Manufacturer's Name: Hewlett-Packard Company Colorado Personal Storage Solutions Division 800 S. Taft Ave. Loveland, Colorado 80537 HP SureStore CD-Writer Plus 8200i, 8210i, 7500i, 7510i C-4415A, C4411A, C4414A, C4410A All EN60950 A4:1995 EN60825-1:1994 CISPR 22:1993/EN 55022:1994 Class B EN 50082-1:1992 IEC 801-2:1991 - 4kV CD, 8kV AD IEC 801-3:1984 - 3V/m IEC 801-4:1988 1kV Power Lines 0.5kV Signal Lines ENV 50140:1993 - 3V/m FCC Part 15 Class B AS/NZS 3548: 1995 IEC 555-2 Manufacturer's Address: declares that the product: Product Name: Product Number: Product Options: Safety: conforms to the following Product Specifications: EMC: Supplementary Information The product herewith complies with the requirements of the EMC Directive 89/336/EEC and carries the "CE" mark accordingly. November 2, 1998 Todd Hammel, Manufacturing Manager European contact: Your local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH, Department HQ-TRE, Herrenberger Strae 130, D-71034 Böblingen (FAX: +49-7031-143143). English-4 FCC Declaration of Conformity According to 47CFR, Parts 2 and 15, Class B Computer Peripherals: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference (2) this device must accept any interference received including interference that may cause undesired operations. This applies to all product options. Hewlett-Packard Company Colorado Memory Systems Division 800 S. Taft Ave. Loveland, Colorado 80537 USA Telephone 970-635-1500 November 2, 1998 Todd Hammel, Manufacturing Manager Canadian Standards Association Information Statement INSTRUCTION TO USER: WARNING: This component is only considered to be approved when installed in CSA certified equipment evaluated to the standards C22.2 No. 220-M1986 or C22.2 No. 950-M89. The operator accessibility into the end use enclosure is defined with strict accordance in the operator's manual for the installation of components into the equipment. BAPT Statement Diese Ausrüstung erfüllt die Europäischen EMC-Bestimmungen für die Verwendung in folgender / folgenden Umgebung(en): s Wohngegenden s Gewerbegebiete s Leichtindustriegebiete (Diese Ausrüstung erfüllt die Bestimmungen der Norm EN55022, Klasse B.) Korean RRL Statement Copyright notice for Denmark: VIGTIGT! Copyright ved brug af CD-Writer 7500i, 7510i, 8200i, 8210i enheder solgt i Danmark I henhold til gældende dansk lov om ophavsret er det forbudt at foretage digital kopiering af et digitalt værk. CD-RW brænderen må derfor IKKE anvendes til at kopiere en musik-CD. CD-RW brænderen må desuden kun benyttes til at kopiere et digitalt EDB-program, når en sådan kopiering tjener til at fremstille et sikkerhedseksemplar af programmet eller hvor kopiering er nødvendig, for at programmet kan anvendes efter dets formål. Hvis De selv har ophavsretten til værket, har De også retten til at foretage digital kopiering med CD-RW brænderen. Installing CD-Writer Plus and Software English-5 Installing CD-Writer Plus and Software English 1. Insert the CD labeled Software Disc 1 into your CD-ROM drive (not the CD-Writer Plus drive). The main menu appears. If it does not appear automatically run SETUP from the installation disc. 2. Watch the installation video (about 6 minutes) by clicking on the Watch Installation Video icon. 3. Get installation recommendations using the Install Assistant that came on your installation disc. Note: Install Assistant provides installation recommendations, but is not required for installation. If you have a CD-ROM, go to the main software setup's menu and click on the Install CD-Writer Plus icon. Install CD-Writer Plus icon If your computer does not have a CD-ROM drive: Create an Install Assistant diskette from another computer's CD-ROM. To copy the Install Assistant program to a diskette, insert "Software Disc 1" into the other computer's CD-ROM drive. From the main menu, click Browse this CD. Double-click the CopyDisk folder and then doubleclick Copydisk.exe. Select the Install Assistant option and follow the instructions. Insert the diskette you just made, into your computer's floppy drive and run A:\ASSIST. 4. Follow the instructions on the screen. English-6 Installing CD-Writer Plus and Software 5. When the CD-Writer Plus Install Recommendation screen appears, click Print. Or, if you don't have a printer, copy the information by hand. You'll need this information in the next section. 6. If you are replacing the CD-ROM drive, remove Software Disc 1 from your CD-ROM drive. 7. After getting the Install Recommendation, you must shut down your computer when prompted, and turn off your computer, monitor, and connected devices. Unplug the power cords from power outlets. 8. Remove the cover from your computer. 9. Prepare the drive bay: If you are installing the drive into an empty drive bay, remove the cover plate from a larger half-height drive bay (approx. 6" x 1.75"/15cm x 4.5 cm). If you are replacing an existing CD-ROM drive, remove the drive. Take note of where the cables are attached and lay them aside to reconnect to the CD-Writer Plus. You will not need the data cable that came with your CD-Writer Plus. If an audio cable was connected to the drive you just removed, you can attach it to your CD-Writer Plus. 10. If the bay requires special rails or brackets to mount the CD-Writer, locate an extra set or contact your computer manufacturer to purchase necessary hardware. 11. Write the CD-Writer Plus' serial number in the space below. The serial number is on the main label on the top of the drive. Serial number: 12. Read the Install Recommendation you printed earlier to learn if the jumper on the CD-Writer Plus should be set as Master or Slave. 13. Find the pairs of pins labeled Master, Slave, and Cable Select on the back of the CD-Writer Plus. Notice that one pair of pins has a small plastic cap or jumper. This jumper can be pulled off using your fingers, tweezers, or needlenose pliers, and placed on a different pair of pins to change the setting. Installing CD-Writer Plus and Software English-7 14. Set the jumper on the CD-Writer Plus as advised in the Install Recommendation Printout for your computer. English Slave Check the back of the new drive and make sure the jumper is on the center location (Slave). Don't use Cable Select This is a jumper. You can pull it off and place it on another pair of pins to change the setting. or Master Check the back of the new drive and make sure the jumper is on the righthand location (Master). 15. Insert the drive into the selected drive bay. Be careful not to dislodge any cables inside your computer as you do this. If you are replacing an existing CD-ROM, skip to step 19 on page 8. 16. If you are installing in an empty drive bay, look at the Install Recommendation Printout again and find whether the data cable should be connected to the computer's primary or secondary IDE controller. English-8 Installing CD-Writer Plus and Software TIP: (For two devices connected to the data cable) If the Install Recommendation states that your CD-Writer Plus drive will share the data cable with another device (such as a CD-ROM drive), follow the cable already attached to the other device to the circuit board to locate the IDE controller that you need. If you find an extra connector along that cable, simply attach that connector to the CD-Writer Plus drive. 17. Locate the recommended 40-pin IDE controller connector (primary or secondary) on your computer's motherboard. IDE connectors are usually found in pairs and may be hidden by some of the computer's cables or may be behind a drive. If your computer has an IDE hard drive or CD-ROM drive, you can follow the data cable from the back of one of those drives to find the IDE controller. IDE connectors may be labeled as any of the following: PRI and SEC, IDE-0 and IDE-1, IDE-1 and IDE-2, HD and CD-ROM, or PCIIDE and ISA-IDE. 18. Refer to the Install Recommendation Printout to see if you will have one or two devices connected to the data cable. See page 10 for examples of one- and two-device installations. 19. Make the necessary data cable connections for your system. Installing CD-Writer Plus and Software English-9 Most data cable connectors are keyed to fit only one way. If your connector is not keyed, make sure the cable's colored edge is aligned with both PIN-1 on the CD-Writer Plus drive and PIN-1 on the IDE controller. If the cable is attached incorrectly, your computer may not boot up. PIN-1 Look for a label identifying PIN-1 next to the IDE connector. The data cable's colored edge is aligned with PIN-1 of the IDE connector. This illustration shows a specific computer. Yours may look different. PIN-1 could be on either side of the IDE connector. English colored stripe on the data cable Colored stripe on the data cable PIN-1 The cable's colored edge is aligne with PIN-1 on the CD-Writer Plus drive. English-10 Installing CD-Writer Plus and Software One Device The OPTIONAL data cable that came with the CD-Writer Plus drive is only used if there ...