User manual KONICA MINOLTA 7115 - annexe 1

Energy Star® As an ENERGY STAR® Partner, we have determined that this machine meets the ENERGY STAR® Guidelines for energy efficiency. What is an ENERGY STAR® Product? An ENERGY STAR® product has a special feature that allows it to automatically switch to a "low-power mode" after a period of inactivity. An ENERGY STAR® product uses energy more efficiently, saves you money on utility bills and helps protect the environment. Contents Contents 1 Introduction 1.1 1.2 We Want You to Be a Satisfied Customer ..................................1-1 CE Marking (Declaration of Conformity) .........................................1-1 SAFETY INFORMATION................................................................1-2 Warning and Precaution Symbols...................................................1-2 Meaning of Symbols........................................................................1-2 WARNING.......................................................................................1-3 CAUTION ........................................................................................1-4 Precautions for Routine Use ...........................................................1-5 Safety Information.........................................................................1-6 Laser Safety ....................................................................................1-6 Internal Laser Radiation ..................................................................1-6 LED Radiation Safety......................................................................1-8 Ozone Release ...............................................................................1-8 Acoustic Noise ................................................................................1-8 About the User Manual .................................................................1-9 Explanation of Manual Conventions................................................1-9 [ ] key...............................................................................................1-9 Explanation of Basic Concepts and Symbols ..........................1-10 Paper Feeding...............................................................................1-10 "Width" and "Length" .....................................................................1-11 Paper Orientation ..........................................................................1-11 1.3 1.4 1.5 2 Precautions 2.1 Installation Precautions................................................................2-1 Installation site ................................................................................2-1 Power source ..................................................................................2-1 Space Requirements.......................................................................2-2 Operation Precautions..................................................................2-3 Operating Environment ...................................................................2-3 Proper Use ......................................................................................2-3 Transporting the Copier ..................................................................2-4 Care of Copier Supplies ..................................................................2-4 Legal Restrictions on Copying ....................................................2-5 2.2 2.3 Konica 7115/7118 i Contents 3 Before Making Copies 3.1 3.2 3.3 Available Features........................................................................ 3-1 Components and Their Functions .............................................. 3-4 Parts Names and Their Functions .............................................. 3-6 Copier ............................................................................................. 3-6 Inside the Copier ............................................................................ 3-8 Options ........................................................................................... 3-9 Control Panel .............................................................................. 3-12 Names of Control Panel Parts and Their Functions ..................... 3-12 Icons on the Control Panel ........................................................... 3-14 Turning ON and OFF and the Initial Mode................................ 3-15 How to Turn ON/OFF the Copier.................................................. 3-15 When Copier is Turned ON .......................................................... 3-15 Default Settings ............................................................................ 3-16 Useful Functions ........................................................................ 3-17 Panel Resetting ............................................................................ 3-17 Auto Panel Reset.......................................................................... 3-17 Power Save .................................................................................. 3-18 Auto Shut OFF.............................................................................. 3-18 Auto Copy Start ............................................................................ 3-18 Interrupting Copy Jobs ................................................................. 3-19 Auto Tray Switching...................................................................... 3-19 Account Number........................................................................... 3-20 To enter an account number ........................................................ 3-20 Printing from the Personal Computer ........................................... 3-21 Sending and Receiving Faxes Using the Copier .......................... 3-21 Copy Paper.................................................................................. 3-22 Paper Specifications..................................................................... 3-22 3.4 3.5 3.6 3.7 4 Loading Originals 4.1 4.2 Two Ways of Loading the Original.............................................. 4-1 Specific Types of Originals ............................................................. 4-1 Loading Originals in the Automatic Document Feeder ............ 4-2 Precautions for Using the Automatic Document Feeder ................ 4-2 Mixed Originals............................................................................... 4-4 Place the Original on the Original Glass .................................... 4-6 Precautions for Placing the Original on the Original Glass............. 4-6 How to position a sheet original...................................................... 4-7 Highly Transparent Originals .......................................................... 4-8 Books.............................................................................................. 4-9 4.3 ii Konica 7115/7118 Contents 5 Making Copies 5.1 5.2 5.3 5.4 5.5 5.6 Copying..........................................................................................5-1 Selecting the Paper.......................................................................5-3 Feeding Paper Manually ...............................................................5-5 Making Copies by Using the Bypass Tray ......................................5-6 Specifying the Zoom Ratio.........................................................5-11 Setting the Zoom Ratio .................................................................5-12 Adjusting the Image Density......................................................5-16 Interrupting a Copy Job..............................................................5-18 6 Advanced Copying 6.1 6.2 Making 1-Sided Copies.................................................................6-1 Output Copies (Sort and Group)..................................................6-5 Three Output Types ........................................................................6-5 Sorting.............................................................................................6-6 Grouping .........................................................................................6-8 Erasing Part of Original Image (Erase) .....................................6-10 Precautions for Erase Position......................................................6-11 Reversing Original Tonal Arrangements ..................................6-13 Providing a Image Shift ..............................................................6-14 Precautions for Image Shift Position .............................................6-14 6.3 6.4 6.5 7 Using the Utility Mode 7.1 User's Choice ................................................................................7-2 Mixed Orig.......................................................................................7-6 Paper Priority ..................................................................................7-6 Copy Priority....................................................................................7-6 Density Priority ................................................................................7-6 Density Level Priority (Auto)............................................................7-6 Density Level Priority (Manual) .......................................................7-7 Output Priority .................................................................................7-7 Crisscross Mode .............................................................................7-7 4in1 Copy Order..............................................................................7-7 Book Binding Position .....................................................................7-7 Margin Setting .................................................................................7-7 Erase Setting (Left, Top, and Frame)..............................................7-8 Auto Panel Reset ............................................................................7-8 Power Save.....................................................................................7-8 Auto Shut OFF ................................................................................7-8 Density (ADF)..................................................................................7-8 iii Konica 7115/7118 Contents Printer Density ................................................................................ 7-8 Paper Auto Detection ..................................................................... 7-9 Paper Size Detection...................................................................... 7-9 Paper Type (1st Tray)..................................................................... 7-9 Paper Type (Bypass Tray).............................................................. 7-9 Special Paper Setting ..................................................................... 7-9 Making the User's Choice Settings............................................... 7-10 7.2 7.3 7.4 7.5 Drum Dehumidify........................................................................ 7-12 Toner Replenisher (Auxiliary Toner Replenishing)................. 7-13 Custom Size Input ...................................................................... 7-14 Administrator Mode.................................................................... 7-16 Administrator Mode ...................................................................... 7-16 Copy Track ................................................................................... 7-18 Disable Auto Shut OFF................................................................. 7-26 Checking the Total Number of Copies/Prints Produced......... 7-28 Storing a Job............................................................................... 7-30 7.6 7.7 8 Error Displays and Other Indicators 8.1 8.2 8.3 8.4 Major Error Displays and Remedial Actions.............................. 8-1 When the Add Paper Indicator Lights up ................................... 8-4 Adding Paper.................................................................................. 8-4 When the Add Toner Indicator Lights up ................................... 8-8 When the Paper Misfeed Indicator Lights ................................ 8-11 Misfeed Indications and Misfeed Locations.................................. 8-11 Clearing a Paper Misfeed ............................................................. 8-12 9 Troubleshooting Tips 9.1 9.2 When This Type of Copy is Produced ........................................ 9-1 When the Copier is not Operating Correctly.............................. 9-4 10 Appendix 10.1 Specifications ............................................................................. 10-1 Copier Konica 7115/7118 ............................................................. 10-1 Automatic Document Feeder DF-217........................................... 10-3 Paper Feed Unit PF-121............................................................... 10-3 Shifting Unit IS-101....................................................................... 10-4 Job Separator IT-102.................................................................... 10-4 Multiple Bypass Tray MT-102....................................................... 10-4 Care of the Copier ...................................................................... 10-5 10.2 iv Konica 7115/7118 Contents Cleaning ........................................................................................10-5 10.3 Function Combination Table......................................................10-6 Function Combination Table .........................................................10-6 Conditions for Combined Functions ..............................................10-6 List of Paper Sizes and Zoom Ratios ........................................10-7 Paper Sizes...................................................................................10-7 Zoom Ratios (Original Size to Paper Size) ...................................10-8 10.4 Konica 7115/7118 v Introduction 1 1 1.1 Introduction We Want You to Be a Satisfied Customer Thank you for choosing a Konica 7115/7118. This User Manual describes the functions, operating procedures, precautions, and basic troubleshooting for the Konica 7115/7118 copier. Before using this copier, be sure to read the User Manual thoroughly in order to ensure that you use the copier efficiently. After you have gone through the manual, store it in the holder on the rear side of the copier and keep it handy at all times. Note that some of the illustrations of the machine used in the User Manual may be different from what you actually see on your machine. CE Marking (Declaration of Conformity) This product complies with the following EU directives: 89/336/EEC, 73/23/EEC and 93/68/EEC directives. This declaration is valid for the area of the European Union. This device must be used with shielded interface cables. The use of nonshielded cable is likely to result in interference with radio communications and is prohibited under EU directives. Konica 7115/7118 1-1 1 1.2 SAFETY INFORMATION Introduction This section contains detailed instructions on the operation and maintenance of this machine. To achieve optimum utility of this device, all operators should carefully read and follow the instructions in this manual. Please keep this manual in a handy place near the machine. Please read the next section before using this device. It contains important information related to user safety and preventing equipment problems. Make sure you observe all of the precautions listed in this manual. * Please note that some parts of the contents of this section may not correspond with the purchased product. Warning and Precaution Symbols Ignoring this warning could cause serious injury or even death. WARNING: CAUTION: Meaning of Symbols Ignoring this caution could cause injury or damage to property. A triangle indicates a danger against which you should take precaution. This symbol warns against possible electrical shock. A diagonal line indicates a prohibited course of action. This symbol warns against dismantling the device. A black circle indicates an imperative course of action. This symbol indicates you must unplug the device. 1-2 Konica 7115/7118 Introduction WARNING 1 · Do not modify this product: Fire, electrical shock, or breakdown could result. If the product employs a laser, the laser beam source could cause blindness. · Do not attempt to remove the covers and panels which have been fixed to the product. Some products have a high-voltage part or a laser beam source inside that could cause an electrical shock or blindness. · Use only the power cord supplied in the package. Failure to use this cord could result in fire or electrical shock. · Use only the specified power source voltage. Failure to do so could result in fire or electrical shock. · Do not use a multiple outlet adapter to connect any other appliances or machines. Use of a power outlet for more than the marked current value could result in fire or electrical shock. Do not unplug and plug in the power cord with a wet hand: An electrical shock could result. Plug the power cord all the way into the power outlet. Failure to do so could result in fire or electrical shock. · Do not scratch, abrade, place a heavy object on, heat, twist, bend, pull on, or damage the power cord. Use of a damaged power cord (exposed core wire, broken wire, etc.) could result in fire or breakdown. Should any of these conditions be found, immediately turn OFF the power switch, unplug the power cord from the power outlet, and then call your authorized service representative. · In principle, do not use an extension cord. Use of an extension cord could cause fire or electrical shock. Contact your authorized service representative if an extension cord is required. Do not place a flower vase or other container that contains water, or metal clips or other small metallic objects on this product. Spilled water or metallic objects dropped inside the product could result in fire, electrical shock, or break-down. Should a piece of metal, water, or any other similar foreign matter get inside the product, immediately turn OFF the power switch, unplug the power cord from the power outlet, and then call your authorized service representative. · If this product becomes inordinately hot or emits smoke, or emits an unusual odor or noise, immediately turn OFF the power switch, unplug the power cord from the power outlet, and then call your authorized service representative. If you keep on using it as is, fire or electrical shock could result. · If this product has been dropped or its cover damaged, immediately turn OFF the power switch, unplug the power cord from the power outlet, and then call your authorized service representative. If you keep on using it as is, fire or electrical shock could result. Do not throw the toner cartridge or toner into an open flame. The hot toner may scatter and cause burns or other damage. Connect the power cord only to an electrical outlet that is equipped with a grounding terminal. Konica 7115/7118 1-3 1 CAUTION Introduction · Do not use flammable sprays, liquids, or gases near this product, as fire could result. · Do not leave a toner unit or drum unit in a place within easy reach of children. Licking or ingesting any of these substances could injure your health. · Do not let any object plug the ventilation holes of this product. Heat could accumulate inside the product, resulting in a fire or malfunction. · Do not install this product at a site that is exposed to direct sunlight, or near an air conditioner or heating apparatus. The resultant temperature changes inside the product could cause a malfunction, fire, or electrical shock. · Do not place the product in a dusty place, or a site exposed to soot or steam, near a kitchen table, bath, or a humidifier. Fire, electrical shock, or breakdown could result. · Do not place this product on an unstable or tilted bench, or in a location subject to a lot of vibration and shock. It could drop or fall, causing personal injury or mechanical breakdown. · After installing this product, mount it on a secure base. If the unit moves or falls, it may cause personal injury. · Do not store toner units and PC drum units near a floppy disk or watch that are susceptible to magnetism. They could cause these products to malfunction. The inside of this product has areas subject to high temperature, which may cause burns. When checking the inside of the unit for malfunctions such as a paper misfeed, do not touch the locations (around the fusing unit, etc.) which are indicated by a "Caution! High Temperature!" warning label. Do not place any objects around the power plug, as the power plug may be difficult to pull out when an emergency occurs. · Always use this product in a well ventilated location. Operating the product in a poorly ventilated room for an extended period of time could injure your health. Ventilate the room at regular intervals. · Whenever moving this product, be sure to disconnect the power cord and other cables. Failure to do this could damage the cord or cable, resulting in fire, electrical shock, or breakdown. · When moving this product, always hold it by the locations specified in the User manual or other documents. If the unit falls it may cause severe personal injury. The product may also be damaged or malfunction. · Remove the power plug from the outlet at least twice a year and clean the area between the plug terminals. Dust that accumulates between the plug terminals could cause a fire. · When unplugging the power cord, be sure to hold onto the plug. Pulling on the power cord could damage the cord, resulting in fire or electrical shock. 1-4 Konica 7115/7118 Introduction Precautions for Routine Use 1 · Do not store toner units, PC drum units, or other supplies and consumables in a place subject to direct sunlight and high temperature or humidity, as poor image quality and malfunction could result. · Do not attempt to replace the toner unit and PC drum unit in a place exposed to direct sunlight. If the PC drum is exposed to intense light, poor image quality could result. · Do not unpack a toner unit or PC drum unit until the very time of use. Do not leave an unpacked unit standing. Install it immediately or poor image quality could result. · Do not keep toner units and PC drum units in an upright position or upside down, as poor image quality could result. · Do not throw or drop a toner unit or PC drum unit, as poor image quality could result. · Do not use this product in an area where ammonia or other gases or chemicals are present. Failure to do so may shorten the service life of the product, cause damage or decrease performance. · Do not use this product in an environment with a temperature outside the range specified in the User manual, as breakdown or malfunction could result. · Do not attempt to feed stapled paper, carbon paper or aluminum foil through this product, as malfunction or fire could result. Do not touch or scratch the surface of the toner unit developing roller or the PC drum, as poor image quality could result. Use the supplies and consumables recommended by the dealer. Use of any supply or consumable not recommended could result in poor image quality or breakdown. Konica 7115/7118 1-5 1 1.3 Safety Information Laser Safety Introduction This is a digital machine which operates using a laser. There is no possibility of danger from the laser provided the machine is operated according to the instructions in this manual. Since radiation emitted by the laser is completely confined within protective housing, the laser beam cannot escape from the machine during any phase of user operation. This machine is certified as a Class 1 laser product: This means the machine does not produce hazardous laser radiation. Internal Laser Radiation Maximum Average Radiation Power: 26.4 µW at the laser aperture of the print head unit. Wavelength: 770-795 nm This product employs a Class 3b laser diode that emits an invisible laser beam. The laser diode and the scanning polygon mirror are incorporated in the print head unit. The print head unit is NOT A FIELD SERVICE ITEM: Therefore, the print head unit should not be opened under any circumstances. Print Head 1-6 Konica 7115/7118 Introduction 1 Laser Aperture of the Print Head Unit There is a laser aperture at the location shown above, which must, however, NEVER be viewed directly by the user. CAUTION Use of controls, adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure. This is a semiconductor laser. The maximum power of the laser diode is 5 mW and the wavelength is 770-795 nm. Konica 7115/7118 1-7 1 LED Radiation Safety Introduction This product is a copier which operates using a LED (light emitting diodes) exposure system. There is no possibility of danger from LED optical radiation, because the LED optical radiation level does not exceed the accessible radiation limit of class 1 under all conditions of operation, maintenance, service and failure. Ozone Release NOTE = Locate the Machine in a Well Ventilated Room = A negligible amount of ozone is generated during normal operation of this machine. An unpleasant odor may, however, be created in poorly ventilated rooms during extensive machine operations. For a comfortable, healthy, and safe operating environment, it is recommended that the room well ventilated. Acoustic Noise For European Users Machine Noise Regulation 3 GSGV, 18.01.1991 : The sound pressure level at the operator position according to EN 27779 is equal to or less than 70dB(A). 1-8 Konica 7115/7118 Introduction 1 1.4 About the User Manual Explanation of Manual Conventions The marks and text formats used in this manual are described below. WARNING Failure to observe instructions highlighted in this manner may result in fatal or critical injuries. Observe all warnings in order to ensure safe use of the copier. CAUTION Failure to observe instructions highlighted in this manner may result in serious injuries or property damage. Observe all cautions in order to ensure safe use of the copier. Note (* May also appear as "Important" or "Tip") Text highlighted in this manner contains useful information and tips to ensure safe use of the copier and serve as supplementary information. It is recommended that you read all of them. 1 The number 1 as formatted here indicates the first step of a sequence of actions. 2 Subsequent numbers as formatted here indicate subsequent steps of a sequence of actions. An illustration inserted here shows what operations must be performed. this style ? Text formatted inassistance.provides additional Text formatted in this style describes the action that will ensure the desired results are achieved. [ ] key The names of keys on the control panel are written as shown above. Konica 7115/7118 1-9 1 1.5 Introduction Explanation of Basic Concepts and Symbols The use of words and symbols in this manual are explained below. Paper Feeding During printing, paper is supplied from the right side of the copier and fed into the Exit Tray on top with the printed surface of the page facing down. The paper feed direction is shown by the arrows in the diagram below. 1-10 Konica 7115/7118 Introduction "Width" and "Length" Whenever paper dimensions are mentioned in this manual, the first value always refers to the width of the paper (shown as "A" in the illustration) and the second to the length (shown as "B"). A: Width B: Length 1 Paper Orientation Lengthwise ( ) If the width (A) of the paper is shorter than the length (B), the paper has a vertical or portrait orientation, indicated by either "L" or . Crosswise ( ) If the width (A) of the paper is longer than the length (B), the paper has a horizontal or landscape orientation, indicated by either "C" or . Konica 7115/7118 1-11 Precautions 2 2 Precautions Observe the following precautions to keep the copier in the best possible conditions. 2.1 Installation Precautions Installation site To ensure utmost safety and prevent possible malfunctions, install the copier in a location that meets the following requirements: - A location away from curtains, etc. that may catch fire and burn easily A location that is not exposed to water or other liquids A location free from direct sunlight A location out of the direct airflow of an air conditioner or heater, and not exposed to extremely high or low temperatures A well-ventilated location A location that is not exposed to high humidity A location that is not extremely dusty A location not subjected to undue vibrations A stable and level location A location where ammonia or other organic gases are not generated A location that does not put the operator in the direct airflow of exhaust from the copier A location that is not near any kind of heating devices Power source The power source requirements are as follows. q q Voltage Fluctuation: Within±10% Frequency Fluctuation: Within ± 3Hz Use a power source with as few voltage or frequency fluctuations as possible. Konica 7115/7118 2-1 2 Space Requirements Precautions To ensure easy copier operation, supply replacement, and maintenance, adhere to the recommended space requirements detailed below. 1038 959 1038 995 1524 1065 Unit: mm Note Be sure to allow a clearance of 100 mm or more at the back of the copier for the ventilation duct and 150 mm or more at the right of the copier for the removal of the misfed papers. 2-2 Konica 7115/7118 Precautions 2 2.2 Operation Precautions Operating Environment The environmental requirements for correct operation of the copier are as follows: q q Temperature: 10°C to 30°C (50°F to 90°F) with fluctuations of no more than 10°C (18°F) within an hour Humidity: 15% to 85% with fluctuations of no more than 10% within an hour Proper Use To ensure the optimum performance of the copier, follow the precautions listed below: - Never place heavy objects on the Original Glass or subject it to shocks. Never open any copier doors or turn OFF the copier while it is making copies/printing, as a paper misfeed could result. Never bring any magnetized object, or use flammable sprays or liquids, near the copier. electrical output. Always make sure that the power plug is completely plugged into the - Always make sure that the copier's power plug is visible and not hidden by the copier. to be used for a long period of time. Always unplug the copier from the electrical outlet if the copier is not Always provide good ventilation when making a large number of continuous copies/printed pages. CAUTION A negligible amount of ozone is generated during normal operation of this copier. An unpleasant odor may, however, be detected in poorly ventilated rooms during extensive copier operations. For a comfortable operating environment, it is recommended that the room be well ventilated. Konica 7115/7118 2-3 2 Precautions CAUTION The area around the Fusing Unit is extremely hot. Do not touch any area other than those authorized in the manual to reduce the risk of burns. Be especially careful not to touch parts marked with warning labels, and their surrounding areas. Transporting the Copier If you need to transport the copier over a long distance, consult your Tech. Rep. Care of Copier Supplies Use the following precautions when handling the copier supplies (toner, paper, etc.). Store the supplies in a location that meets the following requirements: Free from direct sunlight Away from any heating apparatus Not subjected to high humidity Not extremely dusty Paper that has been removed from its wrapper but not loaded in the copier should be stored in a sealed plastic bag in a cool, dark place. - Use only toner that has been manufactured specifically for this copier. Never use other types of toner. Keep all supplies out of the reach of children. CAUTION Be careful not to spill toner inside the copier or get toner on your clothes or hands. If your hands become soiled with toner, immediately wash them with soap and water. 2-4 Konica 7115/7118 Precautions 2 2.3 Legal Restrictions on Copying Certain types of documents must not be copied with the purpose or intent to pass copies of such documents off as the originals. The following is not a complete list, but is meant to be used as a guide to responsible copying. q q q q q q Personal checks Travelers checks Money orders Certificates of deposit Bonds or other certificates of indebtedness Stock certificates Food stamps Postage stamps (canceled or uncanceled) Checks or drafts drawn by government agencies Internal revenue stamps (canceled or uncanceled) Passports Immigration papers Motor vehicle licenses and titles House and property titles and deeds Identification cards, badges, or insignias Copyrighted works without permission of the copyright owner q q q q q q q q q q In addition, it is prohibited under any circumstances to copy domestic or foreign currencies, or works of art, without permission of the copyright owner. When in doubt about the nature of a document, consult with legal counsel. Konica 7115/7118 2-5 Before Making Copies 3 3 3.1 Before Making Copies Available Features The main copy settings available with this copier are listed below. For details on their operation, refer to the pages indicated. Copies q 1-sided copies (p.6-1) q 2in1 copies (p.6-1) q 4in1 copies (p.6-1) q Dual Page copies (p.6-2) Konica 7115/7118 3-1 3 Zoom Ratio q Before Making Copies Reduced/Full Size/Enlarge (p.5-11) Output q Sort (p.6-6) q Group (p.6-8) Note The Output functions available are limited according to the options equipped to the copier. 3-2 Konica 7115/7118 Before Making Copies Applications q 3 Erase (p.6-10) q Reverse Image (p.6-13) q X/Y Zoom (p.5-14) q Image Shift (p.6-14) Mixed Orig. Detection q Mixed Originals (p.4-4) Note The Mixed Orig. Detection function is available when the copier is equipped with an Automatic Document Feeder (option). Konica 7115/7118 3-3 3 3.2 Components and Their Functions Copier q Before Making Copies Konica 7115/7118 Platen Cover CV-117 (option) q Presses down on an original placed on the Original Glass. Standard on Konica 7115. Automatic Document Feeder DF-217 (option) q Automatically feeds originals one page after another for scanning. Paper Feed Unit PF-121 (option) q Capable of holding up to 250 sheets of paper. Shifting Unit IS-101 (option) q Permits sorting or grouping of copies according to the particular output setting made. Performs sorting and grouping of faxes, printed pages, and copies into the upper or lower bin. Job Separator IT-102 (option) q 3-4 Konica 7115/7118 Before Making Copies Multiple Bypass MT-102 (option) q 3 Up to 50 sheets of Paper can be loaded in the Bypass Tray. Pedestal (option) q Adjusts the height when a Paper Feed Unit is mounted. Fax unit for Konica 7115/7118 FK-117 (option) q Permits fax transmission using this copier. A built-in type printer controller that allows the copier to be used as a printer with the copier connected to a personal computer. Allows the copier to be used as a network printer. Printer Controller IP-413 (option) q Network Interface Card KN-305 (option) q 16MB Memory for Copier MU-409 (option) 32MB Memory for Copier MU-410 (option) q Expands the memory capacity of the copier (16MB, 32MB), thereby allowing image rotation and 2in1 copying to be performed. Konica 7115/7118 3-5 3 3.3 Parts Names and Their Functions Copier Before Making Copies 1 6 2 5 3 4 9 10 11 8 7 * The above illustrations represent a copier mounted with the optional Platen Cover. 3-6 Konica 7115/7118 Before Making Copies 3 Description Holds copies fed out face down from the copier. Open when replacing the Toner Bottle. (p.8-8) Holds up to 250 sheets of paper and easily adjusts to different paper sizes. Special paper can be used. (p.3-22) Use for manual feeding of paper. The paper is fed one sheet at a time. Special paper can be used. (p.5-6) Use to unlock the Side Cover. Open to clear a misfed sheet of paper. Use to turn the copier ON and OFF. (p.3-15) Use to align the original. (p.4-6) Holds the original against the Original Glass. Place your original on this glass to allow the copier to scan it. The original is to be placed face down. (p.4-6) Use to start a copy cycle and make necessary settings. (p.3-12) No. 1 2 3 Part Name Copy Tray Front Cover 1st Tray 4 Manual Bypass Tray 5 6 7 8 9 10 11 Lock Release Cover Side Cover Power Switch Original Scales Original Cover Original Glass Control Panel Konica 7115/7118 3-7 3 Inside the Copier Before Making Copies 3 2 1 No. 1 2 3 Part Name Imaging Unit Toner Bottle Holder Pressure Lever Description Forms a copy image. The Imaging Unit is to be replaced only by your Tech. Rep. Open to replace the Toner Bottle. Use to clear a misfed sheet of paper at the Fusing Unit. (p.8-12) 3-8 Konica 7115/7118 Before Making Copies Options 3 3 2 1 4 5 6 Automatic Document Feeder No. 1 2 3 Part Name Document Exit Tray Document Guide Plate Document Feeder Cover (Doc. Feed Cover) Document Feeder Tray Description Receives originals which have been scanned by the copier. Slide the guide plate to the size of the originals. (p.4-3) Open when clearing an original that has been misfed. (p.818) Load the originals to be copied face up on this tray. (p.4-3) 4 Multiple Bypass Tray No. 5 6 Part Name Bypass Tray Bypass Tray Extender Description Up to 50 sheets of plain paper or 20 sheets of special paper can be loaded on this tray. (p.8-7) Slide this Bypass Tray Extender out to load paper of a large size. Konica 7115/7118 3-9 3 Before Making Copies 7 8 9 10 11 Paper Feed Unit No. 7 8 9 10 11 Part Name 2nd Tray 3rd Tray 4thTray 5thTray Side Cover Open to clear a misfed sheet of paper. (p.8-15) Description Up to 250 sheets of plain paper can be loaded. (p.8-6) Konica 7118 accepts a Paper Feed Unit of four trays. Konica 7115 accepts a Paper Feed Unit of one tray. 3-10 Konica 7115/7118 Before Making Copies 3 When Job Separator is Mounted 13 12 14 15 Shifting Unit No. 12 Part Name Copy Tray Description Receives copy sets sorted. Job Separator No. 13 14 15 Part Name Copy Tray Lamp Upper Copy Tray Lower Copy Tray Description Lights up when paper is fed into the Upper Copy Tray. Receives printed pages produced via the personal computer or faxes received. Receives copies made. Konica 7115/7118 3-11 3 3.4 Control Panel Before Making Copies Names of Control Panel Parts and Their Functions No. 1 Part Name PRINT Description · Lit while data received from personal computer is being printed. Blinks while data is being transferred. For details, refer to the Printer Controller User Manual. · Press to select the Job Store mode. Two different jobs can be programmed. · Press to display the Total Counter or Size Counter value. · Press to copy an original with the original tonal arrangements reversed. · Press to select the Mixed Org. or Dual Page function. · Press to select the 2in1 or 4in1 function. 2 3 4 5 6 JOB STORE COUNTER REVERSE IMAGE ORIGINAL COMBINATION 3-12 Konica 7115/7118 Before Making Copies 3 Description · Press to select the erase position. · Press to select the output function. · Press to select the Image Shift mode. · Press to make a copy with different zoom ratios set for X (horizontal) and Y (vertical) directions. · Press to recall either one of the two jobs previously stored in memory. · Press to select the size of the paper loaded in the Bypass Tray. · Press to change the zoom ratio in the range between 50% and 200% in 1% increments. · What is shown on the Display changes from the number of copies to be made to the zoom ratio. · Shows the number of copies to be made, the zoom ratio, and other setting data. · Use to type in the number of copies to be made and any other numeric data. · Press when entering an account number. · Becomes valid only when Copy Track has been set. · Press to set the copier into the Power Save mode. · Press to interrupt a copy job. · Press to reset all copy functions and settings to their defaults. · Holding down the key for 3 seconds or more will set the copier into the Utility mode. · Press to reset the number of copies to "1". · Press to stop a print cycle. · Press to stop a scanning sequence. · · · · Press to start a scanning sequence. Press to start a print cycle. Press to validate the setting just made. The key lights up green when the copier is ready to make copies, orange when it is not ready to make copies. No. 7 8 9 10 11 12 13 Part Name ERASE OUTPUT IMAGE SHIFT X/Y ZOOM JOB RECALL BYPASS TRAY ZOOM 14 15 16 17 18 19 DISPLAY KEY PAD ID POWER SAVE INTERRUPT AUTO RESET 20 21 22 CLEAR STOP START 23 24 25 26 27 ENTER RE APS/AMS PAPER SIZE DENSITY SET · Press to validate the setting just made. · Press to select a zoom ratio from among those fixed ratios available as standard. · Press to select either APS or AMS. · Press to select the paper size. · Press to adjust the image density of the copy. Konica 7115/7118 3-13 3 Icons on the Control Panel Icon Name Paper Misfeed indicator Malfunction indicator Maintenance indicator Description Before Making Copies Lights up when a paper misfeed occurs in the copier. Lights up when a malfunction occurs in the copier. Blinks or lights up when the time approaches that copier needs maintenance service. Call your Tech. Rep. Add Paper indicator Lights up when the paper source currently selected for use runs out of paper. Add Toner indicator Lights up when toner will soon run out. 3-14 Konica 7115/7118 Before Making Copies 3 3.5 Turning ON and OFF and the Initial Mode How to Turn ON/OFF the Copier Turning Copier ON: Press the Power Switch to the 1 (ON) position. Turning Copier OFF: Press the Power Switch to the 2 (OFF) position. Note Do not turn OFF the copier while a copy cycle is being run, as paper misfeed will result. Before attempting to turn OFF the copier, always be sure that the current copy cycle has been completed. Turning OFF the copier will initialize all settings except those for the jobs previously programmed and Utility Mode. Note The copier automatically enters the Power Save mode 15 min after it has been touched last. It also enters the Auto Shut OFF mode automatically 30 min after it has been touched last. The time for the copier to enter the Power Save and Auto Shut OFF mode can be set by selecting User's Choice. For details, refer to "Using the Utility Mode" (p.7-1, p.7-8). When Copier is Turned ON When the Power Switch is turned ON, the [START] key starts blinking indicating that the copier is warming up. At this time, the copier can be specified for the Auto Copy Start function by loading a document in the Automatic Document Feeder and pressing the [START] key. Pressing the [START] key at this time will not immediately start the copy cycle. Rather, you are going to have to wait for about 30 seconds (at an ambient temperature of 23°C). Konica 7115/7118 3-15 3 Default Settings Before Making Copies When the copier is turned ON, the function indicators on the control panel will indicate the default settings which serve as the reference for all control panel settings to be made later. Default settings q q q q q Number of copies: 1 Density: Auto RE: 100% (full size) Paper Size: APS (When Automatic Document Feeder is mounted) Output: Non-Sort